Victory II
Contents
1. Entirely developed by engineers of the SGM Research amp Development Laboratory Has a power supply card CS 0207 and a logic card CS 0208 By means of dip switches to address the control channels of the projector and to set the selectable options PAN TILT scanning inversion 8 or 16 bit mirror movement resolution Control mode Remote from remote control or Auto for automatic functioning independent of the projector 5 a micro stepper motors 5 DC motors Digital serial signal DMX512 or RS232 423 ch1 dimmer ch2 colour ch3 gobos ch4 shutter strobe ch5 pan ch6 tilt ch7 gobo rotation ch8 palette ch9 prism and prism rotation ch10 reset ch11 pan 16bit ch 12 tilt 16bit Mirror rotation by means of 2 extra high precision micro stepper motors and controlled by the relevant control card Option to invert mirror scanning The Victorys are in conformity with current CE regulations IP20 degree of protection Automatic power cut off in case of overheating or cooling system operation failure Forced through 1 axial fan In die cast extruded aluminium Epoxy powder enamelling In epoxy powder enamelled steel Installation position with adjustable inclination over 110 cm 18 x 65 x 35 Weight Kg 14 SGM Elettronica reserves the right to make improvements and modifications to its products at any time Always refer the manual to the equipment it pertains to in order to avoid mis2. After carrying out the necessary operations before pushing the lower part towards the top Fig 2 to close the projector release the locking lever lifting it towards the top Fig 3 Screw down the 2 knobs one after the other taking care that these have properly hooked the lower part to prevent it from suddenly drop ping downwards Projector cleaning Periodic checks Cleaning the optics internally and externally is determining for maximum lumi nous yield and should periodically be carried out The cleaning frequency above all depends on the place where the projector operates In particular a humid environment with a great deal of smoke or dust favours greater accumulation of dirt on the projector optics Clean with a soft cloth using normal window cleaning products or denatured alcohol always carefully drying the parts Clean the external optics at least every 15 20 days and the internal optical unit condenser lenses parabola and gobo unit CEN CT CD CF CE ee SIGIM page 7 SIGIM page 8 including the rotation system at least every 40 60 days To ensure an always perfectly efficient projector a general overall inspection every 700 hours of opera tion is recommended Checking of the electrical and mechanical parts must be carried out by technical staff Colour replacement Open the projector after disconnecting it from the mains If it was on wait for the lamp and the internal mechanical parts to cool down
3. figure adjustable to 4 preset speeds allows obtaining a special visual effect Other than 3 fixed gobos Victory Il is fitted 0 19 No gobo 20 39 Gobo 1 rotante 40 59 Gobo 2 60 79 Gobo 3 rotante 80 99 Gobo 4 100 119 Gobo 5 rotante 120 139 Gobo 6 140 159 Gobo 7 rotante Rotagobo speed 1 160 177 173 194 195 212 Rotagobo speed 2 Rotagobo speed 3 21552209 Rotaqobo speed 4 Music Hard change gobo with 4 variable speed rotating gobos adjustable in the two directions Gobo change with or without blackout The linearity and gobo rotation speed thanks to an exclusive system created by SGM engineers is unequalled and selectable in direction and speed Channel 3 interacts with channel 4 From channel 4 the operator may select gobo change with blackout values 186 198 or slow gobo change values 225 237 shutter strobe The shutter strobe is adjustable from Channel 4 Shutter Strobe O20 Shutter closed Use of iMusic Flashi is recommended see 10 19 table which gives a remarkable visual impact 20 29 2030 Strobe 1 fps Strobe 1 39 fps Channel 4 interacts with channel 2 and channel 3 values 186 237 It can enable colour change and or gobo 40 49 50 59 Strobe 1 65 fps Strobe 1 94 fps Strobe 2 34 fps change with blackout as well as analog 6069 Strobe 2 78 fps gobo change slo
4. not to those on the dip switch Victory Connections The projector is fitted with a DMX512 and RS 232 423 input output When making the start address settings consider that 4 channels are used channel 1 is not operatio nal in this version For connection in a DMX network always use balanced microphonic cables type RF 60 12 2x0 25mm or similar and select a good quality to prevent malfunctioning of the projector To reduce interference it may be necessary to insert a network terminator on the last projector in the DMX chain realized with a 120Q 1 4W resistor placed between pins 2 and 3 of the DMX connector Warning The screening part of the cable braid must NEVER be connected to the system earth since this would lead to malfunctioning of the projector and the control units DMX512 or RS 232 line socket pin out RS 232 423 connection input pin 1 DIGITAL SIGNAL RS 232 COMPUTER OUT output 25 PIN a 09 ween CONNECTOR 3 o 9 SIGIM page 9 CEN CT CD CF CE e SIGIM page 10 OPTIONS Dip switches PAN TILT Normal Reverse The PAN and TILT dip switches are used to invert vert
5. SIGIM LIGHT TECHNOLOGY A C ro l Ig ae a S yi L e Ictory Lx automated luminaire user manual rel 1 02 General warnings Carefully read the warnings contained in this manual since they supply important instructions concer ning safety of installation use and maintenance It is very important that this manual be kept with the equipment for future consultation In case of sale or transfer of the equipment to another user ensure that this manual always accompanies the equipment to allow the new owner to obtain information about the operation and the relevant warnings Not for residential use After unpacking check the integrity of the equipment In case of doubt do not use the equipment and contact an authorized SGM Technical Service Centre The packaging materials plastic bags expanded polystyrene nails etc must be kept out of reach of children since they are potential sources of danger This equipment may only be operated by adults Do not allow children to tamper with the machine or play with the product The electrical work necessary for the installation of the equipment must be carried out by a qualified electrician or by a competent person Before connecting the unit check that the data on the registration plate is the same as that of the electrical grid Avoid using the equipment in places subject to excessive humidity in places subject to vibrations or knocks in places with temperatures h
6. about 30 minutes The colour wheel consists of two parts between which the seats of the colour filters are located To replace them with the finger very gently separate the two locking discs at the point of the dichroic filter to be replaced Remove the filter and insert the new one Properly close the wheel and the projector Gobo replacement Open the projector after disconnecting it from the mains If it was on wait for the lamp and the internal mechanical parts to cool down about 30 minutes With the aid of a small screwdriver remove the spring C replace the gobo B reinsert the spring taking care to insert it perfectly on the special gobo ring A Properly close the projector Start Addresses For connection in DMX512 mode each projector must appropriately be configured The start address is set with the dip switch located on the back of the projector The address can be modified also when the projector is on 1 2 4 8 16 32 64 128 256 Victory II PRO150 1 ch 01 12 Victory II PRO150 2 ch 13 25 Victory II PRO150 3 ch 26 38 Victory II PRO150 4 ch 39 51 1 Ai 2 n E 2 CE 4 w CE 4 CR 8 a CH 8 M 16 16 16 W 32 lo 32 1 32 L_ To 64 Hi 644 HM 644M 128 00 H 1288 HM 256 256 H Js 256IH le Warning Always refer to the numbers silk screen printed on the Victory panel and
7. before commercialisation the Victorys have brilliantly passed the long testing period and the strict tests they have had to undergo this is synonymous with high quality and reliabi lity The particular care over the aesthetics and the optimisation of the outer structure aimed at functiona lity allow easy installation in any position and extremely fast technical intervention The Victorys are constructed in conformity with the CE regulations currently in force Lamp The Victorys use an extra low voltage incandescent halogen lamp with a 2 pin connector without doubt the ideal lamp for this type of projector since it combines good reliability with long life about 300 hours It has surprising luminous power at ridiculously low cost absolutely incomparable with other metallic iodide lamps mounted on projectors of the same type e Optic system The special SGM designed parabola able to concentrate the luminous beam and the condenser lens in selected glass with a high transmission coefficient subjected to special multilayer antireflection treat ment exalt the brilliance and luminous power of the Victorys whose brightness is positively astoun ding Focusing Focusing the Victorys is extremely easy fast and with absolute precision from the screw panel located on the front of the projector Focus Focusing is accurate on all the gobos as they are all arranged on the same wheel Mirror The mobile mirror of the Victorys has ultra high r
8. e and occurs in 0 08 sec To activate change with blackout channel 4 shutter must be set to a value of between 199 and 211 0 9 White 10 19 White Yellow 20 29 Yellow 30 39 Yellow Magenta 40 49 Magenta 50 59 Magenta Cyan 60 69 Cyan 70 79 Cyan Orange 80 89 Orange 90 99 Orange Green 100 109 Green TOSS Green Blue 120 129 Blue 130 139 Blue Red 140 149 Red 150159 Red White 160 170 Rainbow speed 1 171 1380 Rainbow speed 2 181 191 Rainbow speed 3 192 201 Rainbow speed 4 202 212 Rainbow speed 5 AS EURE Rainbow speed 6 224 233 Rainbow speed 7 234 244 Rainbow speed 8 245 255 Music hard change EN CT CD CF CE ee SIGIM page 11 SIGIM page 12 EP The gobo wheel is adjustable from Channel 3 All the gobos are easily interchangeable the light filter diameter is 34 mm The gobo selection is controlled by optical sensors located near the wheel The Victory gobo unit consists of only one wheel with 7 ima ges and one empty position All the gobos are easily interchangeable so that the ope rator may install new figures easily and quickly The gobo change occurs in fast impercepti ble mode or in analog mode with a slow passage from one figure to the next Selecting the rotagobo function running of
9. eflection able to reduce the loss of luminous yield to a minimum The scanning time is 0 5 seconds for the 90 Pan and 0 3 seconds for the 180 Tilt Extremely elaborate software and the use of first class motors have allowed obtaining a movement capability which is ultrafast precise and very linear even at lower speeds Moreover the Victorys accept 16 bit control which ensures a linearity of movement unbeatable among the projectors in this range Mirror scanning can also be inverted to facilitate installation and programming Strobe The stroboscopic effect of the Victorys is extremely fast for a projector of this category and may be adjusted by the operator to a frequency from 1 to 9 flashes a second Dimmer The Victorys are also fitted with a dimmer function so that the light intensity may be dimmed from 0 to 100 CEN CT CD CF CE mie SIGIM page 3 SIGIM page 4 e Diaphragm The Victorys do not have a mechanical iris but the 8 position gobo wheel has a position to shape the luminous beam thus obtaining a narrower beam which for example can be directed at a mirrored globe or used to satisfy any other special need Since the gobo is interchangeable the amplitude of the luminous beam may be selected from the many available Shutter A shutter is available on the Victorys which may be activated instantaneously to block the luminous beam output Colour and colour conversion filter On Victory II the 8 base colours are mul
10. ical and hori zontal scanning from top to bottom from left to right and v versa Ex In the case where two Victorys are installed one in front of the other moving the joystick to the left right or top bottom the Victorys will have opposite movements Therefore to make mirror scanning uniform act on PAN MOVE TILT MOVE of one of these OPTIONS 1234 TILT normal reverse i PAN normal reverse MIRROR res 8 16 bit MODE auto remote TILT normal reverse PANT normal reverse MIRROR res 8 16 bit MODE auto remote OPTIONS TILT 100 x PAN Max AREA DI LAVORO OPTIONS TILT normal reverse _ PAN normal reverse MIRROR res 8 16 bit MODE auto remote TILT normal reverse _ PAN normal reverse MIRROR res 8 16 bit MODE auto remote TILT 100 x Pa PAN 100 x PAN 100 x CENTER POINT AREA Max AREA DI LAVORO Mirror res 8 16 bit The Victorys may also be 16 bit controlled on PAN TILT This function which normally is coupled to more professional projec tors guarantees absolute linearity of movement To activate this function the OPTIONS dip switch 3 must be set to ON In order to use the 16 bit control the Victorys need 2 additional control channels therefore passing from 10 to 12 channels Auto remote mode The Victorys can also function autonomously without the control auxiliary To activate this function the OPTIONS dip switch 4 must be set to OFF The projector will start run
11. igher than 45 C or lower than 2 C Protect the equipment from excessively humid conditions the optimum values are between 35 and 80 Do not disassemble or modify the equipment Prevent inflammable liquids water or metallic objects from penetrating the equipment In case of spilling liquid on the equipment immediately disconnect the power supply of the mixer The minimum distance between the projector and the surface to be illuminated must not be less than 1 5 m In case of serious functioning problems switch off the equipment and contact the nearest SGM retailer or the manufacturer directly for inspection Avoid opening the equipment there are no parts repairable by the user Never try to repair the equipment alone Repairs carried out by inexpert persons may cause damage or serious malfunctioning Contact the nearest authorised Technical Service Centre Always insist on original spare parts Protect the environment do not throw the packaging in your dustbin but return it to your retailer or take it to a collection point for special waste disposal CN CT CD CF CE mie SIGIM page 1 SIGIM page 2 o ONNNNOOOAPAPHPP PP CO CO CO CO CO OO ND gt 10 10 10 10 11 11 12 13 13 14 14 14 Index General warnings Indice Main characteristics Lamp Optics Focusing Mirror Strobe Dimmer Iris Shutter Colour and colour conversion filter Luminous beam diffusion Gobo Prism Technical characteristics Posit
12. ioning and focusing Positioning Focus adjustment Victory I 250 maintenance Access to inside Lamp mounting and replacement Cleaning Periodic checks Colour replacement Gobo replacement Start addresses Victory connections Options Dip switch Pan Tilt Normal Reverse Mirror 8 16 bit res Auto Remote mode Control channels ch 1 dimmer ch 2 colour ch 3 gobo ch 4 shutter strobe ch 7 gobo rotation ch 8 palette ch 9 prism and prism rotation ch 10 reset LIGHT TECHNOLOGY Made in Italy by SGM Electronic Printed in September 1998 Rel 1 02 Main Characteristics The intelligent projectors of the Victory series spring from a design philosophy which all SGM products have for years had in common These new scanners because of their avant garde performance cer tainly take top place among the best in world wide production The accurate study of the functions the search for innovative materials the continuous technical updating have led to the realization of a certainly unique product Victorys are projectors suitable for a multitude of applications The vast and pluridecennial experience of SGM in the sector of light control systems has allowed developing a product with high reliability and precision of which the mechanics optics and electronics are entirely designed by our own research laboratories This allows absolute mastery of the know how and optimisation of the quality price relation As every SGM product
13. is obtained Victory Il is fitted with 4 variable speed rotating gobos adjustable in the two directions Gobo change with or without blackout The linearity and gobo rotation speed thanks to an exclusive system created by SGM engineers is unequalled and selectable in direction and speed according to the requirements of the operator Prism Victory Il is able to create truly innovative and interesting graphic and decorative effects thanks to the use of a rotating prism lens The prism rotation speed is adjustable The fixed and rotating gobos and the rotating prism are totally independent this gives the lighting desi gner a remarkable number of effects to work with since by merely changing a parameter direction or rotation speed of the gobo or the prism the visual effect is changed considerably Technical Characteristics Power supply Lamp Absorbed power Optic unit Optic system Lenses Mirror Electronics Settings Motors Input Control channels Mirror movement Safety regulations Safety devices Cooling system Body Mounting bracket Dimensions 90 260V 50 60Hz Universal automatic voltage change 250W 24V EVC M 33 G6 35 connector Life approx 300 hours 300 W Mirrored parabola with very high luminous yield designed for Victory Mirrored parabola 7Omme lens 9Omma lens screw focusing In glass with high transmission coefficient Ultra high reflection in special glass
14. ly innovative and interesting graphic and decorative effects thanks to the use of a rotating prism lens The prism rotation speed is adjustable The fixed and rotating gobos and the rotating prism are totally independent this gives the lighting desi gner a remarkable number of effects to work with since by merely changing a parameter direction or rotation speed of the gobo or the prism the visual effect is changed considerably Prism on not rotating Prism rotating ae Whenever necessary perhaps due to an imperfect electric line reset the Victory logic which may feel the effects of interference on the network when very powerful from the controller driving the projec tor This may be done thanks to the remote reset first of all activating it on the logic circuit CS0208 from the relevant dip switch Then it can be used according to the following table 0 49 Off 50 234 Lamp histeresis 2357255 Reset SIGM LIGHT TECHNOLOGY Via Pio La Torre 1 61010 TAVULLIA PS e ITALY e Tel 39 0721476477 e Fax 39 0721476170 www sgm it e info sgm it cod M001095
15. ning 8 resident programs AUTO in a continuous cycle 1 2 3 4 Waat o OFF TILT normal reverse PAN normal reverse MIRROR res 8 16 bit MODE auto remote OPTIONS CENTER POINT AREA PAN 50 x Max AREA DI LAVORO OPTIONS 12324 Max AREA DI LAVORO OPTIONS 1 2 3 4 OFF TILT normal reverse PAN normal reverse MIRROR res 8 16 bit MODE auto remote OPTIONS 1234 OFF TILT normal reverse PAN normal reverse MIRROR res 8 16 bit MODE auto remote Control channels nn simmo Adjustable from channel 1 allows linear adjustment of the light intensity from 0 to 100 according to operator requirements EP On Victory Il the 8 base colours are multi plied by a colour temperature conversion fil ter thus obtaining 16 colours The top qua lity 38 dichroic filters are carefully selected to guarantee perfect colour uniformity They are all easily interchangeable so that also personal requirements can be satisfied The colours may be selected as follows e fixed positions full colour e intermediate positions for two colour beams e variable speed rotation to obtain a spectacular rainbow effect e passage from one colour to another with or without blackout e synchronization of the colour change with the music on fixed positions Music Hard The passage between the different colours is imperceptible to the human eye as it is extremely fast the absolute fastest among the projectors in this rang
16. ss to inside Victory has a particular way of access to the inside of the projector Remaining fixed as installed the projector can be opened exactly halfway in longitudinal direction thus allowing easy access to the inner parts in order to carry out any necessary operation be it cleaning lamp change or service of any mechanical or electrical part To open the projector unscrew the 2 knobs on the front Fig 1 taking care that the lower part does not drop downwards suddenly when the screws are undone A locking lever Fig 3 will automatically hold it open at maximum travel fig 2 L Lamp mounting or replacement WARNING Before replacing the lamp Evaluate the effective necessity to replace the lamp average lamp life about 300 h Disconnect the projector from the mains If the projector was on before opening it wait for the lamp and the internal mechanical parts to cool down 10 30 minutes Remove the burnt out lamp Be extremely careful not to touch the optics the parabola and the lamp with bare hands since the residuals subjected to high tem peratures burn causing the parts to blacken and irreparably damaging the lamp Proceed with mounting the new lamp placing it carefully in its housing FOR GOOD PROJECTION IT IS VERY IMPORTANT THAT THE LAMP FITS PER FECTLY IN THE SOCKET After each lamp replacement it Is recommended to carry out a complete cleaning cycle
17. takes and straying from the actual functions as illustrated in the manual CEN Cl CD CF CE SIGIM page 5 appendice SIGIM page 6 Positioning and Focusing Positioning To position the projector the channels must be set as follows Channel 1 dimmer Channel 2 colour Channel 3 gobos Channel 4 shutter strobe Channel 5 6 pan tilt Channel 7 gobo rotation Channel 8 palette Channel 9 orism 100 open white no figure open centre position off none off Position the projector rotating it on its support bracket then lock it in the desired position with the knobs Focus adjustment To adjust the lens the channels must be set as follows Channel 1 dimmer Channel 2 colour Channel 3 gobos Channel 4 shutter strobe Channel 5 6 pan tilt Channel 7 gobo rotation Channel 8 palette Channel 9 prism 100 open white position on a figure open in position on the point where focus is desired off none off Focusing the Victorys is very easy fast and with absolute precision through the screw knob located on the front of the projector Focus Focusing is accurate on all the gobos as they are all arranged on the same wheel Victory II 250 Maintenance Acce
18. tiplied by a colour temperature conversion filter thus obtaining 16 colours The top quality 38 dichroic filters are carefully selected to guarantee perfect colour unifor mity They are all easily interchangeable so that also personal requirements can be satisfied The colours may be selected as follows e fixed positions full colour e intermediate positions for two colour beams e variable speed rotation to obtain a spectacular rainbow effect e passage from one colour to another with or without blackout e synchronization of the colour change with the music on fixed positions Music Hard The passage between the different colours is imperceptible to the human eye as it is extremely fast the absolute fastest among the projectors in this range and occurs in 0 08 sec Diffused light beams Victory Il is equipped with a frost filter to allow emission of diffused light beams to create coloured backgrounds and settings with fixed or variable colours The frost filter may be combined with the whole range of colours available Gobos The Victory gobo unit consists of a single wheel with 7 images and one empty position All the gobos are easily interchangeable so that the operator may install new figures easily and quickly The gobo change occurs in fast imperceptible mode or in analog mode with a slow passage from one figure to the next Selecting the rotagobo function running of figure adjustable to 4 preset speeds a special visual effect
19. w 70 79 Strobe 3 29 fps 80 89 Strobe 3 91 fps 90 99 Strobe 4 56 fps 100 109 Strobe 5 45 fps 110 119 Strobe 5 98 fps 120 129 Strobe 6 98 fps 130 139 Strobe 7 85 fps 140 149 Strobe 9 fps axles Shutter Sync audio low freq 160 172 Flash Sync audio low freq 173 165 Flash Sync audio high freq 186 198 Shutter open amp auto shade gobos 199 211 Shutter open 8 auto shade colours 212 224 Shutter open amp auto shade gobos colours AZA Shutter open low speed gobo change 238 255 gobo rotation Channel 7 controls variable speed rotation in the two directions of the rotating gobos pos 1 3 5 7 Rotating gobos 0 112 cw rotation speed regulation 113 142 stop rotation 143 255 ccw rotation speed requlation Shutter open EN EN CT CD CF CE ee SIGIM page 13 SIGIM page 14 palette Channel 8 controls activation of the palettes which activate the colour conversion and frost filter The colour conversion filter allows doubling the number of colours projected by Victory Il from the 8 base colours 16 are thus obtained The frost filter allows generating diffused light ideal to create coloured backgrounds 0 63 Off 64 127 Colour conversion filter 128 191 Frost 192 255 Colour cov filter frost prism and prism rotation Victory Il is able to create tru
Download Pdf Manuals
Related Search