Manual - Nady Systems, Inc.
Contents
1. SYSTEMS INC 5 Portable Sound System Owner s Manual INTRODUC HON W 3 USING THIS MANUAL 3 SV 9TEM FEATURES 1 11 110 1 4 49511 4 94 4 9 4 4 1 19 9 95 955 16 029 4 5 4 PAS 300BT INSTALLATION WE 5 6 SIGNAL E 7 FRONT PANEL CONTROLS 8 8 10 SERVICE INFORMATION ea 10 WARRANTY GE 11 0 Nady Systems Inc 2 INTRODUCTION Congratulations on your choice of a portable sound system you have purchased one of the finest portable sound systems on the market today This unit was developed using the expertise of professional sound engineers and working musicians You will that your new NADY AUDIO portable sound system has superior performance and greater flexibility than any other portable sound system in its price range Please read this manual carefully to get the most out of your new unit Thanks for selecting NADY AUDIO as your choice in portable sound systems USING THIS MANUAL This booklet provides information regarding the use of the PAS 300BT portable sound system It includes detailed instructions description of features and step by step guides to operating This should answer any questions about the oper2. using the unit 1 INSPECTION Your NADY AUDIO PAS 300BT Portable Sound System was carefully packed at the factory in packaging designed to protect the units in shipment Before installing and using your unit carefully examine the packaging and all contents for any signs of physical damage that may have occurred in transit Please note Nady Systems is not responsible for shipping damage If your unit is dam aged do not return to NADY but notify your dealer and the shipping company if shipped to you immediately to make a claim Such claims must be made by the consignee in a timely CONTENTS PAS 300BT Mixer Section PAS 300BT Left Speaker PAS 300BT Right Speaker 2 2 18 Speaker Cables AC cord Instruction Manual Warranty Card 2 SETUP After transporting the PAS 300BT to the desired location stand the unit upright so that the feet of the speaker are down on an even surface Unlock and carefully remove the amplifier from the back of the speaker if desired and place a flat surface Unlock the accessory panel of the 2nd speaker to retrieve the included speaker and power cables Replace the accessory panel and lock back into place The speakers can now be mounted to any standard speaker stand with 35mm pole Mixer Section Position the PSS 300BT mixer section on its flat surface with the control panel facing up Parts of the unit can become very warm during use This is normal during operation Care should
3. original retail purchase If any such defect is discovered within the warranty period Nady Systems Inc will repair or replace the unit free of charge subject to verification of the defect or malfunction upon return to Nady Systems Please do not return your Nady product to the store where it was purchased as Nady Systems handles your warranty ser vice directly Communication with our Service Department 15 the most efficient means of servicing your unit and we are dedicated to keeping you a Satisfied customer To the extent permitted by law any applicable implied warranties including warranties of merchantability and fitness are hereby limited to one year from the date of purchase Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded This warranty is in lieu of all other agreements and warranties general or special express or implied and no representative or person including a Nady dealer agent or employee is authorized to assume for us any other liability in connection with the sale or use of this Nady Systems product Whereas some states do not allow limitations on how long implied warranties last and do not allow exclusion of incidental or consequential damages the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state This warranty is sub
4. D at rated output REVERB DSP digital reverb SPEAKERS 10 woofer and neodymium horn tweeter AC POWER 110 VAC 60 Hz DIMENSIONS Speaker s 18 4 10 34 9 34 4735 x 273 x 24 76 cm Mixer 11 x6 x3 29 21 x 15 24 x 8 9 cm WEIGHT 21 1 lbs 9 53 kg assembled U S Should your Nady PAS 300BT require either warranty or non warranty service please contact the Nady Service Department via phone at 510 652 2411 or e mail at service nady com for a Return Authorization R A number and a service quote if out of warranty Make sure the R A number is clearly marked on the outside of the package and cashier s check or money order is enclosed if not under warranty or prepaid with a credit card Include a brief description of the problems you are having and if under warranty a proof of date and place of purchase 1 photocopy of bill of sales and ship prepaid to Nady Systems Inc Service Department 6701 Shellmound Street Emeryville CA 94608 For service outside the U S International please contact the Nady distributor in your country through the dealer from whom you purchased this product DO NOT ATTEMPT TO SERVICE THIS UNIT YOURSELF AS IT CAN BE DANGEROUS AND ALSO VOID THE WARRANTY w Nady Systems Inc 10 ONE YEAR LIMITED WARRANTY Nady Systems Inc warrants to the original consumer purchaser that the unit 15 free from any defects in material or workmanship for a period of one year from the date of
5. S00BT T KI TAERE 0517 PORTABLE SOUND SYSTEM wer aera DESIGNED IN CA ISA ASSEMBLED IM CHINA 1 a ee 6 f kel 01 2 0 8 ar a ie 7 Com KE FRONT PANEL CONTROLS amp CONNECTIONS 1 CHANNEL 1 4 XLR INPUT The XLR mic inputs an electronically balanced XLR type designed to accept mic level signals from any balanced or unbalanced low impedance Low Z microphone The XLR Jacks are configured for 1 ground Pin2 positive Pin3 negative The 1 4 mono line inputs are designed to accept unbalanced line level signals such as those trom keyboards drum machines or samplers 2 CHANNEL 5 6 STEREO 1 4 RCA INPUTS The TS 4 or stereo RCA line level inputs can be used for connecting CD players Tape Decks and other audio equipment with line level outputs 3 CHANNEL 7 8 STEREO 1 8 INPUT The stereo 1 8 line level input can be used for connect ing CD players Tape Decks and other audio equipment with line level outputs 4 REVERB CONTROL The REVERB CONTROL knobs can used to add an effect to the mic or line input on any of the inputs 1 4 Adjust the REVERB MASTER knob and control the individual channels REVERB CONTROL by using the knobs on channels 1 4 5 TREBLE CONTROL Turn to the right to boost high frequencies adding cris
6. antom power button to engage power on Ch 1 4 for devices such as condenser microphones that may require an additional 48 volts of power for operation 18 IEC INLET Connect the supplied heavy gauge 3 pin IEC power cable here w Nady Systems Inc 8 5 6 FRONT PANEL CONTROLS amp CONNECTIONS 1 50358 12 14 16 MONITOR DUTPUTS MEDIA PLAYER STEREOIIN 5 6 gt d MopE LINE 0000006 2 2 a 3 54 PAS 300BT EE PORTABLE SOUND SYSTEM POWER CAUTION gt AC95V 250V RISK OF ELECTRIC SHECK SPKR 50HZ 60HZ WARNING SHOCK HAZARD DO NOT OPEN O rower AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR 32 VOLUME VOLUME MEDIA PLAYER MASTER DESIGNED IN CA USA ASSEMBLED IN CHINA 7 4 9 13 158 10 INC nady com 0 SPECIFICATIONS OUTPUT POWER 150W per side into 6 load OVERLOAD PROTECTION Servo system limits the power amplifier input to Automatic Maximum Amplitude prevent clipping distortion that can damage speakers FREQUENCY RESPONSE 40Hz to 20KHz at 3dB TONE CONTROLS Bass 100 Hz 10 dB Treble 10 KHz 10 dB INPUT IMPEDANCE 1 4 Mic input 3 K 1 4 Line input 20K Ch 5 6 TRS 20K Q Ch 5 6RCA 1 2K 0 7 8 3 5 20 MAX GAIN 86 dB mic input to speaker output DISTORTION Less than 0 8 TH
7. ation and servicing of this system 3 nady com KE PAS 3OOBT PORTABLE SOUND SYSTEM Ultra compact portable PA system with 2 speakers and detachable 8 channel powered mixer Lightweight 21 lbs for easy transport and set up Speakers are pole mountable on optional SPST 1A speaker stands Dual 150W Class D amplifier with built in peak limiter Full range 10 woofers and 1 titanium high frequency drivers XLR mic line and stereo RCA inputs All inputs with 2 band reverb and level controls L R stereo and monitor outputs Built in media player with USB SD Bluetooth playback functionality Rear storage compartment for cables and accessories SAFETY TIPS 8 WARNINGS 1 2 10 11 When using this electronic device basic precautions should always be taken including the following read all instructions before using the product Do not use this product near water e g near a bathtub washbowl kitchen sink in a wet basement or near Swimming pool This product should be used only with a cart or stand that will keep it level and stable and prevent wobbling This product combination with headphones or speakers may be capable of producing sound levels that could cause permanent hearing loss Do not operate for a long period of time at a high volume level or at a level that is uncomfortable If you experience any hearing loss or ringing the ears you should consult an audiologist The product s
8. be taken to ensure that there is enough space behind the Mixer Section for cooling Also do not place the Portable Sound System on high temperature devices such power amplifiers etc or the unit may overheat in operation Although the PAS 300BT is shielded against radio frequency RF and electromag netic interference EMI extremely high fields ofRF and EMI should be avoided Please make sure that the power is rated properly for the required voltage 110VAC 60 Hz Power requirements for electrical equipment differ from area to area In new installations and portable sound systems or any situation in which the AC power is in question It is wise to confirm the voltage before connecting it to power sources Europe except UK 230V 50Hz UK and Australia 240V 50Hz USA and Canada 120V 60 Hz For other areas please check with local authorities 5 nady com KE Speakers and Stands To set up fully extend the speaker stand tripod legs and tighten the base screw Extend the pole of the stand to the desired height and insert the safety pin completely through the stand hole above the pole thumbscrew Lower the pole so that the pin rests on the holder and tighten the pole thumbscrew Setup the stands on a flat surface where the speakers will be located not disturbed Place the speakers on the stands and position them as desired and tighten the included bolt on the speaker mount until secured to the pole Note facing the speakers
9. hould be positioned so that proper ventilation is maintained The product should be located away from heat sources such as radiators heat vents or other devices including amplifiers that produce heat The product should be connected to a power supply only of the type described the operating instructions or as marked on the product The power supply cord should 1 be undamaged 2 never share an outlet or extension cord with other devices so that the outlet s or extension power rating is exceeded and 3 never be left plugged into the outlet when not being used for a long period of time Care should be taken so that objects do not fall into and liquids are not spilled through the enclosure s openings The product should be serviced by qualified service personnel if a The power supply cord or the plug has been damaged b Objects have fallen into or liquid has been spilled onto the product c The product has been exposed to rain d The product does not appear to operate normally or exhibits a marked change in performance e The product has been dropped or the enclosure damaged Do not attempt to service the product beyond what is described in the user maintenance instructions All other servicing should be referred to qualified service personnel 0 Nady Systems Inc To ensure years of enjoyment from your NADY AUDIO 300 Portable Sound System please read and understand this manual thoroughly before
10. ject to the following conditions 1 This system must have been purchased from an authorized Nady dealer and all warranty service must be performed by 5 service department Any service not performed by Nady will automatically void this warranty 2 Items not covered physical damage resulting from improper handling of the unit in transit from the factory by the shipper Nady Systems 15 not responsible for such damage and all such claims must be made against the shipping company by the consignee defects caused by normal wear of the product expendable parts are typically connectors cables potentiometers switches and similar components damage or defects caused by abuse neglect accident failure to connect or operate the unit in any way that does not comply with applicable technical or safety regulations or improper repair excessive heat or humidity alteration or unreasonable use of the unit causing cracks broken cases housings or parts finish or appearance items items damaged in shipment en route to Nady Systems Inc for repair The warranty is null and void if any Nady serial number has been removed or defaced 11 nady com KE NADY SYSTEMS INC Emeryville CA USA nady com
11. pness too percussion from drum machines cymbals and synths Turn to the left to cut these frequencies reducing sibi lance or hiss The control has a shelving response giving 10dB of boost or cut at 10kHz 6 BASS CONTROL The bass control shelving response gives 10dB of boost or cut at 100Hz Add warmth to vocals or extra punch to guitars drums and synths by turning to the right Turn to the left to reduce stage rumble hum or to improve a mushy sound 7 CHANNEL FADER The channel faders determine the output signal level to the Master Mix bus It offers a smooth logarithmic taper more often associated with much more expensive consoles for optimum control of the signal 8 MASTER FADER The master fader determines the output signal level of the Master Mix bus They offer a smooth logarithmic taper more often associated with much more expensive console for optimum control of the signal 9 REVERB MASTER KNOB The REVERB master knob 15 used to adjust the amount of reverb added to all channels 10 MONITOR VOLUME KNOB The monitor volume knob controls the output level of the line and stereo RCA record out Note that the monitor out is intended to be used with powered speak ers or other devices that require no additional wattage power 11 MONITOR OUT There 2 14 TS RCA connectors as well as 3 5mm jack for headphone monitoring that be used to connect to powered speakers or any device not requiring additional wat
12. tage power 12 MEDIA PLAYER The PAS 300BT features a USB SD Bluetooth media player built in Simply load a USB driver or SD card with desired MP3s and push the MODE button until the USB or SD media is selected Next use the on board playback controls for play pause rewind fast forward and play When using BT push the MODE button until the word Bluetooth appears You will hear a beep tone come from the speakers indicating itis discovery mode Next pair with your media player and use the Media Player volume knob to adjust the level 13 MEDIA PLAYER VOLUME KNOB Controls the Media Player volume 14 SPEAKER OUT The PAS 300BT has two 4 TS connectors which are powered outputs used to connect your left and right speakers Use the included speaker cables to connect the speakers CAUTION The total impediance load for each side of the amplifier must not be less than 6 Ohms Do not connect additional speakers to the PAS 300BT unless using monitor out section please read above for more details 15 POWER PEAK INDICATOR The POWER LED will illuminate Green when the main power switch is turned on and the red light will indicate the amplifier is near the clipping point If the Peak indicator is consistently light up turn down the MASTER volume or the individual channel faders until the indicator light does not flash consistently 16 POWER SWITCH Use the power switch to turn the PAS 300BT on or off 17 PHANTOM POWER Use the ph
13. towards any of the microphones connected with the PAS 300BT will increase the chance of feedback Connect the speaker cables to the input jacks on the lower left front panel of both the Left and Right speakers Connect the other end of each cable to the corresponding Left and Right speaker outputs on the rear panel of the PAS 300BT mixer section Position the length of the cables so they will not be a safety hazard to people WARNING Connect only the supplied speakers to the PAS 300BT Never connect additional passive speakers to the PAS 300BT Inputs Connect all sound sources to the appropriate inputs 1 microphones keyboards CD players karaoke machines When ready to operate plug the AC cord into the power source Make sure that the unit is turned off before connecting to the AC power source to avoid possible loud transients which can damage your speakers or your ears Before turning on connect up the speakers and all inputs and outputs desired and turn down the Master Volume 0 Nady Systems Inc 6 SIGNAL FLOW MICROPHONE INPUTS 4 XLR JACKS INSTRUMENT INPUTS MONITOR OUTS WITH 3 BAND EQ 4 1 4 JACKS L R 1 4 CABLES AND EFFECTS WITH 3 BAND EQ RCA MAIN OUT L R PHANTOM POWER AND EFFECTS 1 8 AUX JACK 2 1 4 CABLES Microphones Keyboard Guitar ActiveMonitors Included Speakers sa Headphones iPod CD player MWA gt lt gt CG PAS
Download Pdf Manuals
Related Search