IR-E1 PACKAGE CO
Contents
1. The wire lead marked with a gray stripe is positive the unmarked lead is negative USING THE IR BLOCKING COVER To prevent A V components from receiving IR commands from sources other than the IR E1 and IR E2 the IR Blocking Cover should be used The IR Blocking Cover is designed to cover both the IR E1 and IR E2 and the IR Receiver window of the component The IR Blocking Cover serves two functions 1 It ensures that a component receives IR signals solely from the IR E1 and IR E2 2 It prevents the IR output of the IR E1 and IR E2 from radiating to other components or IR receivers R Sty So R Qe Ly Figure 4 Mounting the IR Blocking Cover MOUNTING THE IR BLOCKING COVER Make sure the mounting surface is clean before installing the blocking cover You may improve the appearance by trimming the cover with scissors to exactly cover the remote receiver window Mount the blocking cover using the self adhesive tape so that the IR E1 and IR E2 and the IR remote receiver window of the component are completely covered See figure 4 TROUBLESHOOTING Testing the Remote Control Test to see that the hand held remote control operates the component when you point it at the front panel check the batteries if it does not IR Connecting Blocks Power Supply Check that the red power light on the IR Connecting Blocks is lit the in line power supply should be plugged into an active AC wall outlet2. a Niles Audio Corporation company warrants its passive products those not requiring AC or battery power to the original purchaser to be free of manufacturing defects in material and workmanship for a period of ten years from date of purchase JOBSITE warrants its passive loudspeaker products those not requiring AC or battery power to the original purchaser to be free of manufacturing defects in material and workmanship for a period of five years from date of purchase JOBSITE warrants its indoor outdoor loudspeaker products to the original purchaser to be free of manufacturing defects in material and workmanship for a period of two years from date of purchase JOBSITE warrants its all weather rock loudspeaker products to the original purchaser to be free of manufacturing defects in material and workmanship for a period of five years from date of purchase JOBSITE warrants its active products those requiring AC or battery power to the original purchaser to be free of manufacturing defects in material and workmanship for a period of two years from date of purchase This Warranty is subject to the following additional conditions and limitations The Warranty is void and inapplicable if JOBSITE deems that the product has been used or handled other than in accordance with the instructions provided by the manufacturer including but not limited to damage caused by accident mishandling improper installation abuse negligence
3. and supplying 12V DC 6 Over Please Jobsite PURE CUSTOM JOBSITE SYSTEMS 12331 S W 130 STREET MIAMI FLORIDA 33186 P 866 4JUB SITE 866 452 7483 F 305 238 0185 WWW JOBSITESYSTEMS COM 2004 JobSite Systems All rights reserved JobSite Pure Custom and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logo is a trademark of Niles Audio Corporation All other trademarks are the property of their respective owners Some JobSite products or components thereof are manufactured under one or more U S Patents foreign equivalents and or pending patents see product for details Because we constantly strive to improve our products JobSite reserves the right to change product specifications descriptions and prices without notice The technical and other specifications of information contained herein are not intended to set forth all technical and other specifications of JobSite products Additional information can be obtained at WWW JOBSITESYSTEMS COM or by calling JobSite at 866 452 7483 Printed in China 7 04 DS00392BCN IR Saturation Sometimes the emitter output can saturate the IR receiving window of a component When this occurs the IR command will not be executed This can occur anytime the output level of the emitters exceeds the input capability of the IR receiving circuit Having a Plasma TV in the system can cause this to occur on an intermittent basis Solution 1 Remove the IR Bl
4. FEATURES Infrared pass through housing Miniature size and shape Installation friendly design 10 of cable with 3 5mm plug Reliable adhesive backing Includes IR blocking cover PACKAGE CONTENTS IR E1 IR E1 Emitter x 1 10 Feet of Connecting Wire x 1 IR Blocking Cover x 1 Extra Emitter Adhesive strips x 2 PACKAGE CONTENTS IR E2 IR E2 Emitter x 1 10 Feet of connecting wire x 1 IR Blocking Covers x 2 Extra emitter adhesive strips x 4 PREPARING FOR INSTALLATION The IR E1 and IR E2 are typically mounted to the infrared remote receiver windows of audio video components using the attached self adhesive tape The emitter directs its infrared output toward the component not out into the room If the component has a tray or door that opens you may have to route the emitter wire from the top or the side of the component Make sure the mounting surface is cleaned and degreased before installation PRODUCT OVERVIEW IR Blocking Cover Infrared LED Infrared Transparent Housing Figure 1 Pon 2 conductor INSTALLATION 1 Locate the IR remote receiver window of each component to control The receiver is usually located behind its own plastic window on the front of the component 2 Make sure the mounting surface is clean 3 Attach the IR E1 E2 directly over the IR remote receiver windows of the components using its self adhesive tape 4 Route the connecting two conductor wire to the
5. IR Connecting Block and plug it into an Emitter output 5 Coil any excess wire and tie it in place 6 On IR Connecting Blocks with selectable Emitter outputs make certain the HI LOW SWITCH is placed in the LOW position See figure 2 and 3 Self adhesive tape 10 feet of 3 5mmmo no mini plug liners OWER 1 3 4 3 30V 12VDC I i I I AC DC OUTPUT hav pc o EMITTER OUTPUTS STATUS b IN Jobsite HI HI IR CB2 Low Low IR CONNECTING BLOCK Figure 2 Connecting the emitter to the main system unit s emitter low outputs IR E1 E2 A S60 Resi Ts JobSite Ts IR E1 E2 4 Emitter 12V DC Power Supply Not Supplied plugged into the Switched Outlet IR SMR 12V DC Power Supply Plugged into an Unswitched AC Outlet Figure 3 Powers the System 4 INCREASING THE WIRE LENGTH If the connecting wire is too short to reach the IR Connecting Blocks an additional length of wire may be spliced in to extend it Cut the emitter wire approximately six inches from the plug end strip off 1 4 and connect your additional wiring between the ends of the original emitter wire For distances between 10 and 20 feet upgrade the original wire to an 18 gauge 2 conductor wire For distances of up to 200 feet a 16 gauge two conductor wire should be used Be sure to observe proper polarity when extending the emitter wire
6. ocking Cover if you are using one 2 Turn on the Plasma TV because this may be contributing to the problem 3 Relocate the IR Emitter approximately 1 2 away from the IR Receiving window Some experimentation will be required to determine the best location for emitter 4 Test system Do not use an IR Blocking Cover if a component is sensitive to IR saturation Optical Feedback Loop If you have an IR Receiver in the same room as an emitter and you have some low level noise or interference an optical feedback loop can occur which will interfere with proper operation Symptoms can include poor range intermittent operation or no operation Solution You can eliminate optical feedback by covering all emitters with the supplied IR Blocking Covers There are many methods for reducing interference Which solution is best for you depends on your situation SPECIFICATIONS IR system Works with practically all brands of IR remote controls IR transmitting Up to 4 line of sight Emitters mount directly to the IR window of a component Wiring requirements 10 of 2 conductor 24 gauge wire with a 3 5mm plug is supplied Use 18 gauge for distances up to 20 and 16 gauge for up to 200 Mounting Self adhesive surface mount Dimensions 5 16 wide x 3 16 high x 1 2 deep IR Blocking Cover Dimensions 2 wide x 2 high x 1 4 deep Warranty 2 year limited 10 LIMITED WARRANTY JobSite Systems JOBSITE
7. on may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state For the name of the nearest authorized JOBSITE wholesale distributor contact JobSite Systems 12331 S W 130 Street Miami Florida 33186 WWW JOBSITESYSTEMS COM 12 INSTALLATION amp USER GUIDE Jobsite PURE CUSTOM For Transmitting Infrared Commands to Audio Video Components SINGLE DUAL IR EMITTER IR E1 E2
8. or normal wear and tear or any defect caused by repair to the product other than by JOBSITE or an authorized JOBSITE wholesale distributor To obtain warranty service you must write to 11 JOBSITE Include your name address telephone number model number and serial number of your unit and a brief description of the problem A factory Return Authorization Number will be sent to you DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING WRITTEN AUTHORIZATION AND SHIPPING INSTRUCTIONS FROM JOBSITE If the above conditions are met the purchaser s sole remedy shall be to return the product to JOBSITE in which case JOBSITE will repair or replace at its sole option the defective product without charge for parts or labor JOBSITE will return the unit repaired or replaced under warranty by shipping it by its usual shipping method from the factory only at its expense within the United States of America THERE ARE NO OTHER WARRANTIES INCLUDING WITHOUT LIMITATION EITHER EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER PURCHASER NILES SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO THE EXTENT PROVIDED OR PROHIBITED BY APPLICABLE LAW Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitati
Download Pdf Manuals
Related Search