User Guide - Signal Boosters
Contents
1. 3G 4G Home or Office Five Band Signal Booster Kit User Guide Fusion5 Table of Contents How It Works Pg 3 Package Contents Pg 4 5 Installation Overview Pg 6 Installing Your Hardware Finding the Strongest Signal Pg 7 Installing the Outside Anntenna Pg 8 9 Installing the Insides Anntenna Pg 10 11 Installing Signal Booster Pg 12 13 Configure Gain Setting Pg 14 Troubleshooting Pg 15 16 Specification Pg 16 Kitting Information Pg 17 Warranty Pg 18 19 Safety Information Pg 19 2 Thank you for purchasing SureCall s Fusion5 cellular signal booster kit Fusion5 was specifically designed to eliminate frustrations over dropped calls limited range and slow data rates by amplifying incoming and outgoing cellular signals in buildings homes and offices up to 6 000 square feet The Fusion5 provides enhanced cellular signals for multi carrier 2G 3G and 4G voice and data reception If you have any questions while assembling this kit please contact tech support at 1 888 365 6283 or email us at support surecall com SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 3 How It Works SureCall s Fusion5 is a high quality bidirectional signal booster that enhances cellular signals to areas that are prone to weak cellular coverage Fusion5 works with two or more antennas2. Dome Panel SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 5 Note Fusion5 is available in four kits that are customized to your particular needs Please determine which kit you have from the following list Package Contents Model Antenna Type SC POLYH O 72 OD Kit Omni Outdoor Antenna SC POLYH O 72 YD Kit Yagi Outdoor Antenna SC POLY O 72 OP Kit Dome Antenna SC POLY O 72 YP Kit Panel Antenna Package Options Model No Usage Coverage 1 Outdoor Omni antenna 1 interior dome antenna 30 and 75 SC 400 coax cables SC 288W 1 Outdoor Yagi antenna 1 interior dome antenna 30 and 75 SC 400 coax cables SC 230W S 1 Outdoor Omni antenna with 1 interior panel antenna 30 and 75 SC 400 coax cables SC 222W 1 Outdoor Yagi antenna with 1 interior panel antenna 30 and 75 SC 400 coax cables For a detailed description see Kitting Information on page 21 SC 248W Omni antennas are ideal for topographies with minimal obstacles they have 360 reception Dome antennas are designed for central locations with 360 coverage Yagi antennas are designed to reach carrier towers that are up to 30 miles away Panel Antennas allow optimum reception to targeted areas Note Due to the recent change of our company name from Cellphone Mate CM to SureCall SC
3. 10 dBi SC 222W 7 dBi 3 dBi 3 dBi 6 dBi 6 dBi 2 05dB SC 400 30NN 30 Feet 2 12 dB 2 83 dB 2 98 dB Outside Cable Inside Antenna Inside Cable Gain Loss LTE A Verizon amp ATT 700 Mhz AWS T Mobile 1700 2100 MHz Cellular 800 MHz PCS 1900 MHz Product Number Description Description Note Due to the recent change of our company name from Cellphone Mate CM to SureCall SC we have changed the prefix on all of our antennas cables and accessories from CM to SC Three Year Product Warranty SureCall warrants its products for three years from the date of purchase against defects in workmanship and or materials Specifica tions are subject to change The three year warranty only applies to products meeting the latest FCC Certification Guidelines stated on 2 20 2013 and going into effect April 30 2014 A two year warranty applies to any products manufactured before May 1 2014 Products returned by customers must be in their original un modified condition shipped in the original or protective packaging with proof of purchase documentation enclosed and a Return Merchandise Authorization RMA number printed clearly on the outside of the shipping container Buyers may obtain an RMA number for warranty returns by calling the SureCall Return Department toll free at 1 888 365 6283 Any returns received by SureCall without an RMA number clearly printed on the outside of the shipping container
4. PAYMENT IF ANY RECEIVED BY CELLPHONE MATE INC FOR THE UNIT OF PRODUCT OR SERVICE FURNISHED OR TO BE FURNISHED AS THE CASE MAY BE WHICH IS THE SUBJECT OF CLAIM OR DISPUTE IN NO EVENT SHALL SURECALL BE LIABLE FOR INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES HOWSOEVER CAUSED All matters regarding this warranty shall be interpreted in accordance with the laws of the State of California and any controversy that cannot be settled directly shall be settled by arbitration in California in accordance with the rules then prevailing of the American Arbitration Associa tion and judgment upon the award rendered may be entered in any court having jurisdiction thereof If one or more provisions provided herein are held to be invalid or unenforceable under applicable law then such provision shall be ineffective and excluded to the extent of such invalidity or unenforceability without affecting in any way the remaining provisions hereof SAFETY INFORMATION This is a CONSUMER device BEFORE USE you MUST REGISTER THIS DEVICE with your wireless provider and have your provider s consent Most wireless providers consent to the use of signal boosters Some providers may not consent to the use of this device on their network If you are unsure contact your provider You MUST operate this device with approved antennas and cables as specified by the manufacturer Antennas MUST be installed at least 20 cm 8 inches from any person You MUST cease operating this dev
5. Up to four inside antennas that communicate with your cell phone An outside antenna that communicates with the cell tower Signals sent from a cell tower are received by the outside antenna amplified by the booster and then sent to your phone via the inside antenna When your phone transmits the signal is sent to the inside antenna and then sent to the cell tower via the outside antenna 4 Package Contents 1 Unpack all package contents For missing or damaged items contact your reseller 2 Turn over the signal booster and record the model and serial number for reference Serial Purchase Date 3 Keep the carton and packing material to store the product in case you need to return it Standard Fusion5 signal booster packages include the following items One SureCall Fusion5 booster One outside antenna Cable for connecting the outside antenna to the signal booster One inside antenna Cable for connecting the inside antenna to the signal booster One power supply Warning Unauthorized antennas cables and or coupling devices are prohibited by FCC new rules Please contact the FCC for details 1 888 CALL FCC Changes or modifications not expressly approved by SureCall could void the user s authority to operate the equipment Signal Booster CM288W Omni CM230W S Yagi CM222W Dome CM248W Panel Outside Antenna Option Inside Antenna Option SC 400 Cables Fusion5 Omni Yagi
6. Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com
7. and airtight enclosures 2 If you d like to mount the booster to a wall mark location of screw tabs on the wall in the desired location 3 Use supplied screws or appropriate screws for surface of mounting location and drill through screw tab holes on booster 4 Connect the outside antenna cable to the signal booster connector marked OUTSIDE Hand tighten the connection 5 Connect the inside antenna cable to the signal booster connector marked INSIDE Hand tighten the connection 6 Connect the AC power cord to the signal booster 7 Connect the plug on the other end of the 110V AC power outlet 8 Turn the booster s power switch on SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 13 Installing your Hardware Booster Hardware The following image shows the key hardware components on the cellullar booster Refer to this image as you install your Fusion5 kit components The signal booster turns on automatically Note If the Power LED does not turn ON or the Alert LEDs continue to flash see PAGES 15 16 This booster is rated for 5 20V input voltage DO NOT use the booster with a higher voltage power supply This can damage the booster cause personal injury and void your warranty Power LED N connector to outside antenna N connector to inside antenna Alert LED Programmer Power Sw
8. as no power Verify that the switch on the power supply is turned on and red LED is ON Connect the power supply to an alternate power source Be sure the power source is not controlled by a switch that can remove power from the outlet Check the green POWER LED on the signal booster If it is OFF return the power supply to SureCall Contact tech support at 1 888 365 6283 or support surecall com or go to www surecall com and log on to online support to receive an RMA The Alert LEDs flash after the initial activation period The Alert LEDs continue to flash Lower the dial above the blinking LED by 5dB for example from 65 to 60 and monitor the bars on your cell phone to see whether reception has improved The singal booster shuts down automatically and then restarts after 60 seconds Turn down the PCS Cellular or LTE AWS dial that is oscillating dial that is to prevent the signal booster from shutting down autimatically Problem Resolution SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 17 Kitting Information Kitting Information Component Outside Antennas All equivalent antennas and cables are suitable for use with the Fusion5 booster SC 288W 3 dBi 3 dBi 7 5 dBi 4 dBi 4 dBi 8 dBi 8 dBi SC 230W S SC 230W Option 7 5 dBi 10 dBi 11 dBi 11 dBi SC 400 75NN 75 Feet 10 dBi 4 41dB 6 17dB 6 54 dB SC 248W 4 22dB 7 dBi 10 dBi
9. es for all products returned to SureCall for repair and SureCall will pay the return shipping with the exception of products returned from outside the United States in which case the Buyer will pay the shipping charges The Buyer will pay the cost of inspecting and testing any goods returned under the warranty or otherwise which are found to meet the applicable specifications or which are not defective or not covered by this warranty Products sold by SureCall shall not be considered defective or non conforming to the Buyer s order if they satisfactorily fulfill the performance requirements that were published in the product specification literature or in accordance with samples provided by SureCall This warranty shall not apply to any products or parts thereof which have been subject to accident negligence alteration abuse or misuse SureCall makes no warranty whatsoever in respect to accessories or parts not supplied by it 18 Warranty SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com Limitations of Warranty Damages and Liability EXCEPT AS EXPRESSLY SET FORTH HEREIN THERE ARE NO WARRANTIES CONDITIONS GUARANTEES OR REPRE SENTATIONS AS TO MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR OTHER WARRANTIES CONDITIONS GUARANTEES OR REPRESENTATIONS WHETHER EXPRESSED OR IMPLIED IN LAW OR IN FACT ORAL OR IN WRITING SURECALL AGGREGATE LIABILITY IN DAMAGES OR OTHERWISE SHALL NOT EXCEED THE
10. ge significantly Any reduced antenna separation reduces the booster s cellular signal capabilities Alert LTE A dB Gain dB Gain dB Gain dB Gain dB Gain OFF OFF OFF OFF OFF 39 39 40 47 46 44 44 45 52 51 49 49 50 57 56 54 54 55 62 61 59 59 60 67 66 64 64 65 72 71 Alert LTE V Alert CELLULAR Alert PCS Alert AWS If Coverage Area is 3000 6000 square feet 60 80 feet 50 75 feet 40 60 feet 35 50 feet 30 35 feet 2000 4000 square feet 1500 2000 square feet 1000 1500 square feet 1000 square feet and below And Antenna Separation is Set All Dial to 65 default setting 60 60 60 60 WARNING Do not adjust the uplink and downlink dB attenuation settings more than 20dB This could cause the booster to shut down SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 15 Troubleshooting In the event you encounter a problem follow the suggestions below to resolve the issue One of the red LEDs next to the dials on your signal booster is flashing red Your signal booster restarted and shut down for 15 minutes and is now shut down permanently The red LED goes ON The Power LED does not turn ON Turn down the dB gain on the dial until the light goes OFF or turns yellow Be sure the ins
11. he N Female connection from the interior antenna to the cable leading to the connector labeled INSIDE on your booster Step 4 Tighten fixing nut to secure antenna do not over tighten Storage and transportation Store and place in non extreme room temperature and dry environment Attention This antenna should not be used near open fire or flame The SC 222W multi band plastic antenna is an omni directional interior antenna that gathers signals from all sides Range of antenna is dependent on three factors 1 physical obstructions 2 power generated by booster and 3 reception from outside signal received and distributed by outside antenna Besides the antenna itself parts include mounting equipment for either a flat horizontal surface or a wall It should be mounted in an upright position for best results You can also install your interior antenna above the ceiling panel provided your ceiling isn t made of a material that could obstruct signals from the booster Step 1 Drill a 35mm diameter hole in the ceiling The ceiling thickness should be 20mm maximum Step 2 Unscrew fixing nut from antenna Place antenna cable through hole Screw the fixing nut back onto antenna and cable on crawl space side of ceiling and fasten 12 Installing Your Hardware Step 4 Install the Signal Booster 1 Select a location close to a working AC outlet Do not expose the signal booster to excessive heat direct sunlight moisture
12. ice immediately if requested by the FCC or a licensed wireless service provider WARNING E911 location information may not be provided or may be inaccurate for calls served BY USING THIS DEVICE 48346 Milmont Drive Fremont California 94538 USA 888 365 6283 Fax 510 996 7250 www surecall com SureCall has made a good faith effort to ensure the accuracy of the information in this document and disclaims the implied warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may be stated in its written agreement with and for its customers SureCall shall not be held liable to anyone for any indirect special or consequential damages due to omissions or errors The information and specifications in this document are subject to change without notice 2014 All Rights Reserved All trademarks and registered trademarks are the property of their respective owners SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 19 Warranty SureCall 48346 Milmont Dirve Fremont CA 94538 1 888 365 6283 sales surecall com BEFORE USE you MUST REGISTER THIS DEVICE with your wireless provider and have your provider s consent Most wireless providers consent to the use of signal boosters Some providers may not consent to the use of this device on their network If you are unsure contact your provider You MUST operate this device with approved antennas and cable
13. ide panel antenna is facing away from the outside antenna Use the recommended antenna separation 72dB 100 110 ft separation 65dB 75 80 ft separation 55dB 60 ft separation 50dB 50 ft separation 45dB 15 20 ft separation 40dB 5 6 ft separation Signal booster has no power After installing your signal booster system you have no signal or reception Verify that the booster switch is turned on Connect the power supply to an alternate power source Be sure the AC outlet is working and is not controlled by a wall switch that can cut power to the outlet If the green POWER LED on the signal booster is OFF return the power supply to SureCall Contact tech support at 1 888 365 6283 or support surecall com or go to www surecall com and log on to online support to receive a Return Merchandise Authorization RMA Check the strength of the outside signal as close as you can to the outside antenna see instructions on page 7 Double check all signal booster and antenna cable connections Be sure your signal booster s dB gain is turned up to full power on each dial see apge 14 Each SureCall signal booster is equipped with Auto Shutdown to prevent cell tower interference The outside antenna may be close to a cell tower Move the outside antenna to a location that provides sufficient distance from the cell tower to prevent the signal booster from automatically enabling Auto Shutdown Once away from the original location perform
14. itch 5 6 4 PCS 1900 Uplink AWS 2100 Uplink Power OFF normal operation ON AWS uplink warning Power off booster immediately Green ON or blink booster receiving power OFF booster not receiving power Red ON oscillation has occurred for longer than 15 minutes and the booster is shuttin down OFF normal operation ON PCS downlink warning Power off booster immediately LED 1 2 3 LTE 707 Uplink LTE 781 Uplink Cellular 800 Uplink OFF normal operation ON LTE Verizon uplink warning Power off booster immediately OFF normal operation ON LTE AT amp T uplink warning Power off booster immediately OFF normal operation ON Cellular uplink warning Power off booster immediately Designation Description 14 Step 5 Configure Gain Settings 1 Find the PCS Cellular and LTE AWS dials on top of the signal booter 2 Set the dials according to the coverage area and the distance between the indoor and outdoor antennas see next page If you Want to Improve Coverage 1 Find a location that receives a stronger signal and relocate the outside antenna to that location 2 Increase the distance between the outside and inside antennas 3 Be sure your signal booster s dB gain is turned up to maximum gain on each dial Installing Your Hardware Note As you can see from the table above acquiring the recommended indoor and outdoor antenna separation optimizes covera
15. minimum cellular signal of low 100 dBm Signal readings usually appear as a negative number for example 85 The more bars you get the closer the dB gets to zero Aim for a signal close to 50dB Signals stronger than 50dB may cause the booster to shut down see the graph below If you have an omni outside antenna and your signal is too weak you may need a yagi antenna which can be aimed at the closest antenna tower Before installing the outside antenna find the area with the strongest cellular signal source from your service provider by following the directions below You can also go to www antennasearch com to find the general location of carrier towers Measure the strength of the existing cellular signal in various locations Apple iPhones Dial 3001 12345 and press Call In the top left corner a dB number appears instead of bars Android devices download apps such as Network Signal Info in the Google Play store to measure signal strength Search check real signal strength to find other cell signal measurement apps Internet go to www speedtest net to test 3G and 4G data rates 2 Select a location away from buildings walls trees hills and other terrain features that can block or reflect wireless signals 12 inch clear radius is recommended Note Where you install your outside antenna in relation to the carrier s cell phone tower also determines signal strength Although cell phone carriers try t
16. o place towers for maximum coverage local ordinances and terrain features can restrict tower locations which can limit signal strength at your location Cell Tower Outside Antenna Signal Strength 50dB 60dB 70dB 80dB 90dB 100dB 110dB Excellent Good Poor 8 Installing Your Hardware Step 2 Install the Outside Antenna 1 Outside omni antennas receive and send signals in a 360 radius Yagi or directional antennas work best when facing the direction of cellular phone towers Mount the outside antenna as high as possible If you are installing a Yagi antenna set it up facing the cellular tower in the area where you located the best signal source see step 1 on the previous page 2 Make sure that the mounting area has at least a 12 inch radius clear of obstructions and other radiating elements 3 If the mounting area is prone to weak cellular signals or if the density of the roof and ceiling partially block the signal the booster will operate at its default setting of 65 dB gain be sure to place the outside antenna at least 75 feet from the inside antenna for best performance 4 Do not collocate antennas or operate the outside antenna with any other antenna or signal booster 5 Run the SC 400 cable from the outside antenna to the signal booster Hand tighten the connection IMPORTANT For boosters enhancing T Mobile s AWS frequencies the FCC has stated for consumer signal boosters
17. ome type mount it on the ceiling in a central location 2 If your indoor antenna is a flat panel install it against a wall or surface projecting the area where you want reception Point the antenna away from the outside antenna To avoid interference stay a minimum distance of 3 feet from the panel antenna 3 Run the SC 400 cable from the inside antenna to the signal booster Connect the inside antenna to the booster connector marked INSIDE see page 13 4 Hand tighten the connection Step 3 Install the Inside Antenna Inside antennas come in omni directional dome and flat panel versions Installing Your Hardware Note As you can see from the table above acquiring the recommended inside and outside antenna separation optimizes coverage significantly Any reduced antenna separation reduces the booster s coverage Note see next page for outside antenna installation details Required Between Outside and Inside Antenna Antenna Separation Table antenna separation 40dB 5 6 45dB 15 20 50dB 50 55dB 60 65dB 75 80 72dB 100 110 Amplifier gain Min separation ad Fusion5 Optional 1 Inside Dome Optional 2 Inside Panel SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 11 Amplifier gain Min separation ad Installing Your Hardware Step 3 Attach t
18. operating as a fixed station in the 1710 1755 MHz uplink 2110 2155 downlink bands the users or installation manual must contain the 30 foot height restriction requirements per FCC 27 50 d 4 Optional 1 Outside Omni Optional 2 Outside Yagi Fusion5 SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 9 Fusion5 s omni antennas come with equipment for mounting on a vertical wall For best results the antenna should be mounted in an upright position Step 1 Unscrew antenna from L mounting bracket on antenna base with hands or wrench if needed Step 2 Using vertical plate of bracket mark position of desired placement with pencil or marker Step 3 Unscrew nut on end of stucco screw and remove it along with lock washer and regular washer Step 4 Place vertical plate into desired location and tap the screws head first along with sleeve into stucco 1 2 to 5 8 deep into place Step 5 In this order place washer lock washer and nut on each screw and tighten until secure When tightening screw sleeve will expand to secure plate Screw antenna securely back onto horizontal plate Installing Your Hardware Note If desired surface for installation plate is wood or concrete wood or masonry screws for L plate will have to be purchased separately 10 1 If your indoor antenna is a d
19. s as specified by the manufacturer Antennas MUST be installed at least 20 cm 8 inches from any person You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider WARNING E911 location information may not be provided or may be inaccurate for calls served by using this device This is a CONSUMER device Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help SureCall 48346
20. the procedure under step 3 on page 10 More antenna separation is needed If you cannot provide more antenna separation and the Alert LEDs flash after the initial activation period lower the dial above the blinking LED by 5dB for example from 50 to 45 and monitor the bars on your cell phone to see whether reception improves Be sure the AC outlet is working and is not controlled by a wall switch that can cut power to the outlet Problem Resolution LED flashing yellow This means that the Automatic Gain Control AGC is adjusting which is part of the boosters normal operation 16 Specifications Product Name Fusion5 Uplink Frequency Range MHz 698 716 776 787 824 849 1850 1915 1710 1755 G Block Included 728 746 746 757 869 894 1930 1995 2110 2155 G Block Included 50 72dB 8 dB 2 0 CDMA WCDMA GSM EDGE HSPA EVDO LTE and all cellular standards Input AC110V 60 Hz Output DC 5 20V 1 Watt EIRP SC 400 N Female both ends lt 50W 10 x 9 x 2 25 9 5 lbs RSNFUSION 5 Downlink Frequency Range MHz Supported Standards AC Input VSWR Maximum Gain Noise Figure Input Impedance Maximum Output Power Cable RF Connectors Power Consumption Dimensions Operation Temperature 4 F to 158 F Weight FCC USA SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com Your signal booster h
21. we have changed the prefix on all of our antennas cables and accessories from CM to SC 6 Step 1 Make sure you have positioned the booster close enough to an existing electrical outlet Step 2 Make sure you have sufficient cable length between proposed outside antenna location and booster connector Step 3 Make sure you have sufficient cable length between proposed inside antenna location and booster connector Additional cable may be purchased from your dealer if needed Installation Overview Step 1 Find the outside area that has the strongest signal See page 7 for directions as needed Step 2 Install the outside antenna in the area identified in step 1 See page 8 9 for directions as needed Step 3 Install the inside antenna See page 10 11 for directions as needed Step 4 Mount the signal booster connect the outside and inside antenna cables to the signal booster and connect the booster to an AC power source See page 12 13 for directions if needed Step 5 Configure gain settings on the signal booster if needed See page 14 for directions as needed Before You Install Outside Omni Fusion5 Inside Domes Outside Omni SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com SureCall 48346 Milmont Drive Fremont CA 94538 1 888 365 6283 sales surecall com 7 Installing Your Hardware Step 1 Find the area with the Strongest Signal The signal booster requires a
22. will be returned to sender In order to receive full credit for signal boosters all accessories originally included in the signal booster box must be returned with the signal booster The Buyer does not need to include accessories sold in addition to the signal booster such as antennas or cables This warranty does not apply to any product determined by SureCall to have been subjected to misuse abuse neglect or mishandling that alters or damages the product s physical or electronic properties SureCall warrants to the Buyer that each of its products when shipped will be free from defects in material and workman ship and will perform in full accordance with applicable specifications The limit of liability under this warranty is at SureCall s option to repair or replace any product or part thereof which was purchased up to THREE YEARS after May 1 2014 or TWO YEARS for products purchased before May 1 2014 as determined by examination by SureCall prove defective in material and or workmanship Warranty returns must first be authorized in writing by SureCall Disassembly of any SureCall product by anyone other than an authorized representative of SureCall voids this warranty in its entirety SureCall reserves the right to make changes in any of its products without incurring any obligation to make the same changes on previously delivered products As a condition to the warranties provided for herein the Buyer will prepay the shipping charg
Download Pdf Manuals
Related Search