HydraMeter Installation Guide 2015
Contents
1. bring power to a HydraMeter HydraMeter 2 Another way to bring power along with communications to the HydraMeter is to connect it to an iDrop iDrops are installed into conventional electrical junction boxes Since these boxes come in a variety installation and service types the box that best suits the environment should be used For example if an iDrop is to be installed into an existing wall a conventional wall type box is suggested If the iDrop is to be installed outdoors a weather proof box is appropriate Power is brought into the iDrop using a Seco Sys provided AC power supply with an output rating of 12 volts DC On the back of the iDrop are connectors with colored terminals similar to those found on the HydraMeter Connect the red positive wire from the power supply to the right hand red terminal on the iDrop connector The black negative wire from the power supply is to be connected to the right hand black terminal The green will be empty Along with distributing power for HydraMeters special function iDrops provide a docking station for specialized Seco Sys water management devices These iDrops can provide interface to third part water management devices such as irrigation controllers and supervisory control and data acquisition SCADA systems A special function iDrop will have connectors labeled Pulse Flow and RS 232 are reserved for interface with compatible third party equipment This feature permits the2. Water Control Technologies ELECTRICAL SPECIFICATIONS e Input power 12 VDC 50mA MAX e Reserve Power 3 7v Lithium lon Polymer Battery e Output Valve Control 12 VDC Latching or Continuous Current 1 5 Amp Max impulse e Output Valve Control e Type DC Latching or Continuous Current e Power 12 VDC 1 5 Amp Max Impulse Current e Optional Pump Control e Type Non Latching Relay Coil e Power 12 VDC 50mA Max WARRANTY e 3 year limited warranty SECO SYS0 4 PAGE Water Contro Technologies HydraMeter Installation Where to install the meter Prior to securing the HydraMeter controller the water meter must be plumbed by a competent installer The water meter can be installed above or below ground level depending on local climate conditions The preferred alternative is to place the HydraMeter above ground where the water delivery plumbing and electrical power are easily accessed For below ground installations the meter should be contained in a meter box as depicted below If the HydraMeter and an electronic valve are to be housed in a common meter box the box should be at least 16 inches in length for meters up to 9 inches long and 24 inches in length for meters ups to 16 inches long These boxes are low cost and readily available from plumbing and landscape outlets or home improvement stores NOTE The HydraMeter is water tight as long as either a cable or the supplied grommet plugs are inserted into the three black grom
3. is permitted to run e Configurable limit alert by high flow rate limits the highest flow rate permitted for any event e Configurable limit alert by low flow rate limits the lowest flow rate permitted for any event e Configurable limit alert by flow volume limits the volume of water delivered for any event e Configurable leak rate detection independent of low flow rate e Configurable water window schedules up to 4 per day e Flow time limits can be set to 16 hours 39 minutes in one second increments e Optional output for booster pump control activated by user defined flow rate e Pulsed flow output signal to share live flow rate data with compatible equipment e Independent programmable alarm delay time for all limits e Connectivity for networking multiple HydraMeters up to 19 in cascaded configuration AVAILABLE OPTIONS e Ability to connect to the internet using SecoNet via HydraPod or HydraConnect e Ability to operate in remote locations using solar power from a HydraPod e Ability to share flow data with SCADA and other compatible third party equipment MECHANICAL SPECIFICATION e Durable fade resistant injection molded plastic enclosure with hinged lid e Water tight transparent cover with valve control access e Liquid tight cord grip connection ports e Dimensions e 41 4W x3H x5 1 2D inches 107 95W x 76 2H x 139 7D mm without meter adapter e Shipping Weight 12 3 Ounces without meter adapter SECO SYS0 3 PAGE
4. mets at the front of the HydraMeter and those grommets are tightened appropriately While our valves are also watertight neither the valves nor the HydraMeter are intended for continuous submerged use Hence if water is anticipated to continually enter and flood the meter box the installation of the HydraMeter and valve should be above ground Water Meter Installation The HydraMeter is a combination of an AWWA approved water meter and the HydraMeter Controller The HydraMeter Controller can be mounted to most meter service sizes mounts by latching onto the mounting flanges normally used to secure a mechanical register Refer to the Table of Meters for a list of compatible meters e To plumb a water meter special seals and flange adapters are used establish a leak free connection e The flange type depends on the meter size see illustration below e The flange fittings must be appropriately spaced apart to accommodate the meter that will be installed 5 8 to 1 inch service A Electronic Valve 1 inch and up Meter Fittings Mounting Flange Face to face ds fitting spacing GH fa Os required for a o or particular size _ ine water meter can A B i be determined i from Table 1 A SECO SYS 5 PAGE Water Control Technologies For sizes above 2 inches use the manufacturers dimensional specifications and recommended meter couplings Bringing Power to the HydraMeter 3 Ways to
5. patent pending nvurameter i Installation Guide 4 20 2015 SECO SYS 1 PAGE Water Control Technologies 4 20 2015 Introduction Congratulations You have selected the most advanced and diverse water management device available With engineering inspiration Seco Sys has designed and developed the HydraMeter to be the first fully comprehensive water management device ever conceived The HydraMeter is an ultra intelligent water meter controller that mounts atop many common water meters In its application users can have visibility and control of water consumption in a way never obtained before Like Hydra the powerful multi headed water serpent of Greek mythology Seco Sys HydraMeter has several metering personalities and modes of operation This unique ability makes it possible for the HydraMeter to tackle nearly any water management task setting it apart from other available water management devices Key features are as follows e Advanced flow measurement and processing for flow rate flow time and flow volume e Independent control of master valves and pumps e Configurable water budget management with automatic alarm response e Direct interface with flow sensor compatible control systems e Internet communication capable The HydraMeter facilitates a single solution for all water management requirements The HydraMeter controller is completely scalable and mounts to nearly any AWWA approved water meter allowing i
6. se wire colors correspond to the colors of the HydraMeter 2 connection terminals and SecoNet labels Bring the 3 wire communication cable through one black grommet on the HydraMeter to one set of SecoNet terminals on the iDrop The red SecoNet terminal distributes power on the network and is intended for connection with the red power wire lead The SecoNet terminal distributes data on the network and is intended for connection with the green communication wire lead The black terminal distributes the negative voltage and ground on the network and is intended for connection with the black negative wire lead Bringing Valve Control to the Valve ain ire the HydraMeter sid The HydraMeter provides 12 VDC ValveNet output to drive an electric control valve Valves can be either motorized or latching solenoid type To wire the valve to the HydraMeter bring the valve wiring through a black grommet Connect the red positive lead of the valve to the red ValveNet connector terminal and black negative lead of the valve to the black ValveNet connector terminal Power amp Web Use SecoNet to connect to an iDrop to ace ali power to raMeters of your netwo Now dock your Communication Use SecoNet to network multiple HydraConnect HydraMeters di your iDrop and it s all as ia SECO SYS0 7 PAGE Water Control Technologies
7. sharing of relevant information with other devices or systems such as irrigation controllers or supervisory control and data acquisition devices 3 Finally power can be supplied to the HydraMeter by connecting it to a solar powered HydraPod The wiring is similarly color coded and more specific instructions can be found in the HydraPod installation manual 6 PAGE 1 If you are using the HydraMeter as a stand alone product you will use the supplied wall mount 12 Volt DC at 300 milliamps power supply Make sure that the power outlet you use is appropriate to the environment and complies with any local building or safety codes Minimally we recommend a weatherproof outlet with a built in high sensitivity GFCI Connect the red positive wire from the power supply to a red SecoNet terminal on the HydraMeter Connect the black negative wire from the power supply to a black SecoNet terminal on the This is where the red and black wires from the 12 Volt DC Power Supply go Back of the iDrop This is where the red green amp black communication wires from the HydraMeter go SECO SYS0 Water Contro Technologies Networking your Hydra Meters SecoNet SecoNet allows more than one HydraMeter to be networked together HydraMeter to HydraMeter SecoNet communication uses a three conductor communication cable The cable specified by Seco Sys has three 24 gauge conductors red green and black wires housed in a PVC jacket The
8. t to easily integrate and manage water for small or large water delivery systems To take full advantage of the many personalities and features of your HydraMeter please take the time to review the user manual i J A Il AMICIORS ni This guide is intended to be a general overview and is NOT a plumbing How To If you are not experienced in water meter installation or have any doubts as to your abilities please seek out a qualified installer If you are doing your own installation be aware that you are doing so at your own risk and Seco Sys will not be held liable for failures due to improper installation procedures SECO SYS0 2 PAGE Water Control Technologies HydraMeter Specifications BASIC METERING FEATURES e Acquires flow measurement resolution from AWWA water meters e Measures flow down to 04 gallons per minute with zero drag e Multiple character LCD display to interpret water consumption and alarms e Configurable units of measure Gallons or Liters e Simultaneous display of flow rate and accumulated volume OPERATING FEATURES UME me METER e Multi mode keypad interface for direct configuration ug e Manual control keys to Open or Close a connected valve 0 123 124456 e Rechargeable Lithium lon Polymer Batter KS m m eo CONTROL FEATURES e Control output for electric valve Motorized or DC Latching type e Configurable limit alert by flow time limits how long a flow event
Download Pdf Manuals
Related Search