User Manual - Online Security Products
Contents
1. Pi DAMPING P2 DAMPING P3 DRIVE P4 GND Auto Iris Direct Drive Connections C or CS Mount Lenses Most lenses are available in 2 different mounting options C mount and CS mount CS mount lenses are now the most popular size as they are shorter and more compact than C mount lenses Most cameras are now manufactured to accept CS mount lenses Before fitting the lens you need to verify that you are using a CS mount lens with the camera You can confirm this with your lens supplier or the literature that came with your lens check the instructions or packaging to see if your lens is a C or a CS mount version If your lens is a C mount type you can still fit it to the camera by following the instructions under the heading Using a C Mount lens Using a CS Mount lens If you are using a standard CS mount lens you can screw the lens straight into the camera without the need for the C CS adapter ring supplied Email suppornt nitedevil com Last Revised 03 01 1 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic Adjusting the inner focus ring Once you have fitted the lens if you have a picture on the monitor but cannot correctly focus the lens by the fine focal adjust on the lens itself you may need to alter the inner adjusting ring that is screwed into the end of the camera To do this you will need a small Allen key This ring enables the lens to either sit a little closer or a little further away fr2. Select OFF to revert to normal video MIRROR MIRROR ROTATE V FLIP OFF This option allows the normal video displayed to be switched to vertical flip horizontal flip both or none MIRROR This flips the camera view vertically on the screen Ee l l D ZOOM ROTATE This flips the camera view horizontally on the screen V FLIP This flips the camera horizontally and vertically on the screen ees eh kee PAN 0 D ZOOM OFF ON 2 This option switches on digital zoom TLT 0 RETURN RET 4T GAMMA The standard value is 0 45 The values 0 05 1 00 can be set NEG IMAGE OFF ON Acolour negative image can be set RETURN Returns to the SPECIAL menu SPECIAL RS485 CAM TITLE OFF ON _ D EFFECT lt 1 RS485 lt 1 CAM ID ID DISPLAY MOTION OFF PRIVACY OFF SYNC INT LANGUAGE ENGLISH RETURN lt BAUDRATE RETURN The RS485 option allows you to control these menu settings by connecting a CATS matched pair to the RS485 connections on the back of the camera and the other end of the cable to an RS485 keyboard controller or a DVR that has PTZ functionality Ensure that the polarity 1s correct to the control device On the DVR you will need to connect to the T and T RS485 transmit connections In order to see the camera menu it will be necessary to set the camera ID number and the baud rate The camera is set to the Pelco D protocol and this cannot be changed The baud rate is usually set to 2400 baud
3. This will give the longest distance coverage These settings will have to be reflected in the control device whether it is a keyboard or a DVR Note that you need to check that the DVR used has this functionality Email suppornt nitedevil com Last Revised 03 011 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic Note if using the Alien DVR then by selecting the PTZ option and clicking on ZOOM this will display the menu Use the up and down arrow keys to locate an option and use the right arrow key or ZOOM to select option SPECIAL MOTION This option allows motion detection to be set 1 CAM TITLE OFF ON lt T and to display MOTION DETECTION on the monitor pE An output on the camera allows a closed contact to be made A by using the M D OUT and ground 3 RS485 lt a 4 MOTION OFF 5 PRIVACY OFF MOTION 6 SYNC INT 7 LANGUAGE ENGLISH AREA SELECT AREA1 4 RETURN r AREA DISPLAY ON OFF LEFT RIGHT i WIDTH 42 TOP BOTTOM 38 vot seer ead HEIGHT 30 otion can be detected in 1 4 areas You can select 1 4 areas in SENSITIVITY setting To see DED Ena ee 3 the MOTION DETECTION message displayed on MOTION VIEW OFF ON the monitor MOTION VIEW must be set RETURN END T AREA SELECT 1 4 Select the area required AREA DISPLAY ON OFF Determines whether to use the motion area selected in SENSITIVITY LEFT RIGHT Determines the vertical axis for area WIDTH Adjusts the
4. ensure that the positive and negative connections are correct If incorrectly V Auto IRIs connected damage to the camera may result The 12V DC cameras require a power supply that has a continuous rating of 140mA or higher per camera It is recommended that you allow headroom per camera to be on the safe side especially taking into account any extra load created by adding an auto iris lens typically 10mA The power supply you choose must be a well regulated one giving a smooth regulated 12V DC output and it is recommended that it should be rated at no less than 200mA D amp N MID RS485 in ot WARNING This power supply must not be a security type used in intruder alarms as the over voltage may damage the camera and void the warranty The earthing arrangement of an intruder type alarm PSU may give rise to problematic earth loops and poor voltage regulation can give poor noisy image quality We offer no technical support or warranty with the camera if you use a 13 8V intruder alarm PSU as it is contrary to the installation amp usage instructions of the camera The terminal strip will facilitate easier and faster power connection without the hassle of soldering The terminal connection can be seen in the picture above The 12V and Ov connections from the power supply must be connected correctly If you have a 2 1mm jack plug connected to your power supply you will need to cut this off and use the bare wires to connect to the termin
5. 3 011 2010
6. ER AUTO 1 50 FLK 1 250 1 500 1 2000 1 5000 1 10000 1 100000 x256 x128 x64 x32 x16 x8 x4 x2 Select EXPOSURE by using UP amp DOWN buttons and then select desired mode AUTO Select this mode to control the shutter speed automatically FLK Select this mode if flickering occurs on screen BRIGHTNESS 1 100 You can control the brightness by using the LEFT amp RIGHT buttons in Manual lens mode If using a DC lens switch LENS to manual adjust brightness then return to LENS and select DC AGC OFF LOW MIDDLE HIGH Set AGC from low to high gain Note that the higher the gain level the brighter the screen but the higher noise level Note that if AGC shows then RESET the camera SENSE UP OFF AUTO T X2 x4 x8 x16 x32 x64 x128 x256 When it is dark the camera automatically detects the light level and tries to compensate by maintaining a clear picture OFF The option is deactivated when the OFF option is selected or when AGC is OFF or DAY amp NIGHT is OFF AUTO You can adjust brightness by increasing decreasing the shutter speed x2 x256 Note that noise can be amplified as SENSE UP in increased Email support nitedevil com Last Revised 03 011 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic BLC OFF BLC HsBLC 4A Backlight compensation allows you to get a clear picture even when objects are in a strong backlight BLC 4T Selecting BLC and pressing SET button enters th
7. IT colors AWC SET The auto white balance control analyses the incoming light and estimates the best camera setting for pleasing MANUAL lt T This option allows the blue and red colours to be manually set INDOOR Select this when the colour temperature is around 3 100 K OUTDOOR Select this when the colour temperature is around 5 100 K SPECIAL NOTE In the event that problems are found with the white balance settings it is recommended that the AWC mode is selected These problems can be 1 When the colour temperature in the environment is beyond the control range 11 If the camera is situated close to a fluorescent light white balance may become unstable Email suppornt nitedevil com Last Revised 03 011 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic DAY NIGHT COLOUR AUTO EXT BW MENU SETTINGS COLOUR The option will always display in colour 1 LENS MANUAL 2 EXPOSURE lt 1 AUTO 2 This option allows colour mode during day 3 WHITE BAL AWB and b w at night or when ambient light levels are low To setup 4 DAY NIGHT AUTO the switching time or speed press the SET button 5 3DNR on lt T 6 SPECIAL 7 ADJUST DAY NIGHT AUTO RESET DELAY 9 EXIT 8 S LEVEL 63 E LEVEL 55 RETURN DELAY The seconds before the switch from one mode to the next mode S LEVEL The setting of the brightness illumination before switching from colour to b w E LEVEL The setting of the bright
8. LE CAM TITLE If you wish to display the camera title you must switch 0123456789 camera title to ON ABCDEFGHIJK Note that if the CAM TITLE is OFF no title is LMNOPQRSTUV displayed on the monitor even if one is entered Move up and down buttons to select CAM TITLE and switch it ON Then press the SET button and move to the required character using the direction buttons and press the SET button to select Repeat to select up to 15 characters If you move to CLR and press the SET CIR pos button all characters are cleared To edit a character select the character bottom left arrow and press SET button move the cursor over the character to be edited then select the character required and press the SET button Then select POS to position cam title press SET move to the position required and select END Press SET again to return to SPECIAL menu WXYZI I gt aayo dO pane ee SPECIAL D EFFECT CAM TITLE OFF ON D EFFECT lt RS485 lt i MOTION OFF PRIVACY OFF SYNC INT _ LANGUAGE ENGLISH RETURN lt 1 FREEZE OFF ON MIRROR MIRROR V FLIP ROTATE OFF D ZOOM OFF on GAMMA 0 45 NEGIMAGE OFF ON RETURN RET 2 NDA WAR WD gt Email support nitedevil com Last Revised 03 011 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic D EFFECT This option covers the display effects that can be selected FREEZE OFF ON This option if set to ON will freeze current picture
9. NS y Moves cursor left and right or change the value of a selected item 1 2 3 4 5 6 7 3 9 FUNCTION MENU D 4 IENS mDC MANUAL oa e o mg SENSE UP mBLC HSBLC gD WDR ror seek R m INDOOR gsOUTDOOR m ATW 3DNR ON OFF SPECIAL CAM TITLE g D EFFECT EEE ao gPRIVACY i Sooo a GUAGE ADJUST mg SHARPNESS me mm RESET mFACTORY E R S O CEEE S Email support nitedevil com Last Revised 03 011 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic NOTE All menu items with the Sol icon require the SET button to be depressed If is displayed then feature is unavailable on this camera Menu Settings LENS When the SETUP menu screen is displayed select LENS by 1 LENS MANUAL using the UP amp DOWN buttons so that the arrow selects a LENS 2 EXPOSURE 3 WHITE BAL AWB Select the connected type by using the LEFT amp RIGHT 4 DAY NIGHT AUTO Wons 5 3DNR oy lt E 6 SPECIAL ff Selecting MANUAL selects manual lens 7 ADJUST lt Selecting DC selects Auto Iris Lens When MANUAL is 8 RESET Pe a selected you can select the brightness control by pressing the a SET button Set range between 0 100 Then select DC 9 EXIT MENU SETTINGS EXPOSURE LENS EXPOSURE WHITE BAL DAY NIGHT 3DNR SPECIAL ADJUST RESET EXIT SHUTTER 1 250 BRIGHTNESS AGC MIDDLE SENSE UP OFF BLC OFF D WDR RETURN 1 2 3 4 5 6 7 8 9 SHUTT
10. Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic NiteDevil CAM190 192 194 These NiteDevil Cameras have Digital WDR functionality allowing improved picture quality in mixed lighting conditions They are complimented with an OSD menu allowing access via camera or RS485 privacy masking digital zoom to 32x and adjustable NiteDevil settings The cameras are supplied in three versions CAM190 12v DC only CAM192 Dual voltage 12vDC 24vAC CAM194 240v AC Lens supplied separately 3 fitted lens options All 3 cameras provide a resolution of 600TVL in colour and 700TVL in b w These cameras come with many of the NiteDevil features including an OSD menu the SENS UP feature allowing minimum illumination down to an incredible 0 00019 Lux and a WDR option Features v 1 3 Sony Super HAD CCD 600 700 TVL VY Low Light 0 00019Lux v Wide Dynamic Range setting v Maximum 2watts power consumption v 3 Lens Options vV SENS UP auto function 2x 256x v Built in OSD menu v Built in 3DNR function v Privacy Masking v RS485 menu control v Electronic Shutter v Motion Detection Alarm Function v Digital Zoom up to 32x v Contrast amp Sharpness adjustments Powering the Camera CAM190 The CAM190 requires a 12v DC regulated power supply providing a minimum of 140mA When connecting to any 12v DC power supply always use a regulated e FX supply The camera has a terminal connection This camera is polarity sensitive so
11. SPECIAL menu This option is not selectable CAM TITLE OFF ON DANCUACE _ D EFFECT Pe English Chinese or Japanese Pe RS485 If you change this you can work out how to return to MOTION OFF English by selecting option 7 PRIVACY OFF SYNC INT RETURN Returns to SPECIAL menu LANGUAGE ENGLISH RETURN lt T 1 2 3 4 5 6 7 8 Email support nitedevil com Last Revised 03 011 2010 Nite www nitedevil com evil MENU SETTINGS 1 LENS MANUAL 2 EXPOSURE lt it 3 WHITE BAL AWB 4 DAY NIGHT AUTO 5 3DNR on f 6 SPECIAL lt T 7 ADJUST lt 1 8 RESET lt 1 9 EXIT lt ADJUST Doc XCAM190 NiteDevil Traditional Wide Dynamic ADJUST SHARPNESS 21 m gt RETURN This option is used to improve the sharpness of the picture and balance the blue and red colour SHARPNESS This sets the sharpness by moving the direction keys to right or left Parameter ranges from 0 31 BLUE This sets the overall blue hue Parameter ranges from 0 100 RED This sets the overall red hue Parameter ranges from 0 100 RETURN This returns to the main menu MENU SETTINGS LENS EXPOSURE WHITE BAL DAY NIGHT 3DNR SPECIAL ADJUST RESET 1 2 3 4 5 6 7 8 EXIT f EXIT This saves the changes made and exits the main menu Email suppornt nitedevil com FACTORY RETURN RESET This option resets the camera to factory defaults RETURN Retu
12. al strip Note that the 12V positive is the wire that was connected to the centre pin of the jack plug and the OV wire was connected to the outer case Email suppornt nitedevil com Last Revised 03 01 1 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic CAM192 The CAM192 is a dual voltage camera allowing connection of 12vDC or 24vAC power supply This camera is not polarity sensitive so the positive or negative can be connected either way round The 12V DC cameras require a power supply that has a continuous rating of 140mA or higher per camera It is recommended that you allow headroom per camera to be on the safe side especially taking into account any extra load created by adding an auto iris lens typically 10mA The power supply you choose must be a well regulated one giving a smooth regulated 12V DC output and it is recommended that it should be rated at no less than 200mA CAM194 The CAM194 is a mains 240vAC controlled camera and a mains power cable 1s supplied AUTO IRIS Fitting the Camera Lens POWER INLET Fit the Auto Iris Direct Drive Lens connector to connection shown Auto Iris Direct Drive Connections Auto Iris type lenses require the 4 pin connector to be attached to the camera It is important that this connector is wired correctly If you bought the lens from SystemQ and it s a direct drive lens this will be pre wired and you can simply plug the lens into the camera
13. e BLC menu BLC HSBLC MENUS This menu allows a selected area of the picture to be viewed more GAIN clearly in varying light conditions DEFAULT GAIN LOW MIDDLE HIGH Select the level of gain by selecting low middle or high LEFT RIGHT DEFAULT Press SET button to select default option WIDTH The LEFT RIGHT WIDTH TOP BOTTOM and HEIGHT are TOP BOTTOM used to create a window and place it in the picture view using BLC When there is a bright light e g headlights on a car using the HEIGHT Se HSBLC menu may compensate for this condition so allowing you to view a car number plate that would otherwise be obliterated by RETURN the light level D WDR OFF INDOOR OUTDOOR Digital Wide Dynamic Range allows de saturation of light in a single pixel so providing the mean light level overall This allows a scene that may include for example objects that show light and shade and then compensates by providing an overall balanced light view WDR can be set to INDOOR OUTDOOR or OFF MENU SETTINGS WHITE BAL ATW AWB AWC SET MANUAL INDOOR OUTDOOR LENS MANUAL TRE ATW Auto Tracking White Balance Suitable for viewing EXPOSURE objects with changing colour temperature Select when colour WHITE BAL temperature between 2 500 K and 9 800 K DAY NIGHT 3DNR AWB Auto White Balance This uses stored settings for white balance and is most suitable where there is little change in light source SPECIAL ADJUST RESET EX
14. force a lens when it becomes tight on the camera or you may damage one or the other device A C mount lens fitted on a CS mount camera may protrude too far into the camera and cause irreparable damage Setting Up an Auto Iris Direct Drive Lens for different Light Levels The brightness setting in the menu determines when the IRIS of the lens opens and closes It is important to set this correctly as if the brightness level is set too low you may get satisfactory pictures during the day but at night not enough light can enter the camera giving poor quality pictures The trick to setting up the brightness level is to set it up in the brightest possible conditions 1 e midday on a sunlight day and keep the IRIS open to its maximum without a too bright picture This means at night in low light the IRIS will be open as much as possible and give the best results To do this follow these steps With the camera in the brightest light conditions that it will be expected to work 1 Enter the LENS menu and set to MANUAL The enter EXPOSURE menu increase to 100 and then reduce level until the picture is okay Do not adjust further This will ensure that the iris is set to its widest setting 2 Now return to the LENS menu and select DC Then exit the menu Once you have done the above the lens will restrict the light sufficiently in bright sunlight but open up to its maximum in low light giving the best night time performance Further details on the menu
15. ness illumination before switching from b w to colour EXT This deactivates the EXT function BW This option will always display in black and white SPECIAL NOTE You cannot control the DAY NIGHT menu when AGC in the EXPOSURE menu is set to OFF If it is then DAY and NIGHT mode will operate only in COLOUR mode MENU SETTINGS 3DNR OFF ON 4 Digital Noise Reduction reduces the background noise in a LENS low light environment EXPOSURE WHITE BAL Select ON and press SET button to enter 3DNR menu DAY NIGHT 3DNR SPECIAL ADJUST RESET EXIT 1 2 3 4 5 6 7 8 9 OFF Deactivates 3DNR Noise is not reduced ON Activates 3DNR so that noise is reduced SPECIAL NOTE You cannot set the 3DNR to ON or OFF when the AGC mode in the EXPOSURE menu is set to OFF When adjusting the noise reduction level in this mode the higher the setting the more the noise level will be reduced but the more likely ghosting will occur Email suppornt nitedevil com Last Revised 03 011 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic MENU SETTINGS SPECIAL 1 LENS MANUAL 2 EXPOSURE it 1 CAM TITLE OFF ON 4A 3 WHITE BAL AWB 2 D EFFECT lt 4 DAY NIGHT AUTO Np pe 2 DINK on 4 MOTION OFF 6 SPECIAL lt i 5 PRIVACY OFF 7 ADJUST lt T 6 SYNC INT ne pe 7 LANGUAGE ENGLISH P a po pe 8 RETURN CAM TITLE Allow the display of a 15 character camera title displayed on the monitor CAM TIT
16. om the camera to get a sharp focused image when using lenses from different manufacturers To adjust the inner focus ring you will need to slacken the ring by loosening the grub screw s with an Allen key This is a trial and error process by moving the ring in or out say 1 2 turn then locking it again and trying to refocus the lens It is possible with common sense to work out whether the lens needs to be nearer or further away from the camera by watching for improvements in focus at each attempt NOTE If it appears that the lens will never be in focus then it is possible that you are trying to fit a C mount lens on the camera not a CS mount lens If this is the case you will have to add the spacer ring to the lens that was provided free with the camera The spacer ring looks something like this Using a C Mount Lens If you are using a C mount lens you will need to add the C CS mount adapter ring This ring effectively moves the C mount lens an extra 5mm away from the camera body to achieve the correct focusing of the lens Once you have fitted the adapter ring you can carefully screw the lens to the camera If the picture is out of focus try focusing it in using the focus adjust on the lens itself If you can nearly get the focus right but not quite because the lens runs out of adjustment then you probably need to adjust the inner focus ring with the Allen key See Adjusting the inner focus ring above It is important that you never
17. ra to allow the camera menu to be updated using an RS485 keyboard or using the PTZ option in a DVR You will need to use the direction keys Zoom and Focus controls to edit the menu Alternatively you can change the menu settings using the menu control buttons on the rear of the camera Precautions Do not install the camera in extreme temperature conditions Only use the camera where temperatures are between 20 degrees centigrade and 50 degrees centigrade Never install the camera in damp or humid conditions This can affect image quality This camera requires stable lighting conditions to operate effectively Do not touch the front lens of the camera Fingerprints can stain the lens glass The camera must not be placed directly facing the sun or strong light This may damage the camera CCD Never expose the camera to rain or liquids These will corrode the camera electronics Do not subject the camera to vibration as it may cause camera malfunctions Only use this camera in a housing if used externally To display the OSD menu press the SET button Menu closes when no operation Menu Settings SET BUTTON Displays menu LENS EXPOSURE WHITE BAL DAY NIGHT 3DNR SPECIAL ADJUST RESET EXIT on the screen Press button down W A to confirm status or after A changing a selected item POWER UP DOWN BUTTON Used 0 gt to move cursor up and down to SET select a menu item LEFT amp RIGHT BUTTO
18. rns to main menu Last Revised 03 01 1 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic TECHNICAL SPECIFICATIONS SOIRE F 1 2 0 00019 Sens up 256x Electronic Shutter Speed Auto FLK PAL 1 50sec 1 100 000sec BLC HSBLC Off On Off Selectable Day amp Night Auto B W Colour selectable EXT Digital Zoom On Off Ox 32x On OFF OK 32K S O D Effect Freeze Mirror D Zoom Gamma Neg Image RS485 Menu Control Supplied Voltage 12vDC 12vDC 24vAC 240vAC 140mA 2 0W Infra Red Sensitive Yes 65mm x 65mm x 127mm excluding lens Approx 50g f used electronic equipment must not be mixed with general household wast notice Whilst every effort is made to ensure that these For treatment recovery and recycling please return this unit to your trade instructions are complete and accurate nitedevil com cannot be All specifications are approximate nitedevil com reserves the l l vo This symbol on the products and or accompanying documents means that right to change any product specifications or features without Supplier or local designated collecton pointas defined by your local council Ea held responsible in any way for any losses no matter how they arise from errors or omissions in these instructions or the WEE CG0783S5 performance or non performance of the equipment that these instructions refer to Email suppornt nitedevil com Last Revised 0
19. selected vertical area TOP BOTTOM Determines the horizontal axis for area HEIGHT Adjusts the selected horizontal area SENSITIVITY You can select up to 4 areas The higher the sensitivity the smaller the change to initiate motion detection MOTION VIEW If you set this option to ON you can select an area colour and display MOTION DETECTION on the monitor RETURN Return to SPECIAL menu e 2 MEFR PAES ll Use the M D Motion Detection and G Ground So Se lt s connection if you wish to use the motion alarm switch eee Wo 666 939 3 Be wD sas ocv g AC 24V Email support nitedevil com Last Revised 03 011 2010 Nite www nitedevil com Doc XCAM190 i NiteDevil Traditional Wide Dynamic PRIVACY ON OFF SPECIAL Allows an area on screen to be hidden 1 CAM TITLE OFF ON PRIVACY 2 D EFFECT lt T AREA SELECT AREA 1 8 3 RS485 lt lt AREA DISPLAY ON OFF 4 MOTION OFF LEFT RIGHT 51 5 PRIVACY OFF E S 5 6 SYNC INT me 7 LANGUAGE ENGLISH TOP BOTTOM y y y 38 RETURN it HEIGHT 380 COLOUR 34 RETURN END f AREA SELECT 1 8 Select the area required AREA DISPLAY ON OFF Determines whether to use the area selected in AREA SELECT LEFT RIGHT Determines the vertical axis for area WIDTH Adjusts the selected vertical area TOP BOTTOM Determines the horizontal axis for area HEIGHT Adjusts the selected horizontal area COLOUR You can select area colour from 0 15 RETURN Return to
20. setup and operation are covered below Connecting Video The video out from the camera is provided from the BNC connector located at the rear of the camera The camera s video signal is carried by a suitable cable usually RG59 or similar to the monitor or other video input ie of a switcher quad DVR etc Remember that the Video out from the camera is like any other electrical circuit and requires two wires to complete the circuit When using a co ax type cable such as RG59 or similar the outer braid of the co ax provides the OV GROUND connection and the inner core provides the Video connection A typical connection is shown as follows a Video Cable p Video Out l Video Input on DVR BNC vu u monitor etc RG59 Cable Outer braid to body of BNC plug Solid centre core to middle pin of BNC plug Email suppornt nitedevil com Last Revised 03 011 2010 Nite www nitedevil com Doc XCAM190 NiteDevil Traditional Wide Dynamic It is recommended that when you are first setting up the cameras that you use a short BNC BNC cable to link the camera directly to the monitor and to set it up at the same time This allows you to both understand the camera and get the very best out of this great product as you will be able to adjust the camera whilst looking at the monitor screen Obviously whilst you are setting up the camera it does need to be powered This camera has an RS485 terminal connection on the rear of the came
Download Pdf Manuals
Related Search