MANUAL DE USUARIO GEPON ONU HG326E
Contents
1. D Netelcom 2 2 Panel Figure 3 Panel lights HG326E EPON HGU User Manual db F N er C2 1 1 A i LD 3 il vs a S 4 we w J CZ 1 2 3 4 5 6 7 8 9 LED Mark Status Description ON The device is powered up FOuen En ONE OFF The device is powered down Optical er Blink Device does not receive optical signals signal 2 OFF Device has received optical signal ON The device is registered to the EPON system Registrati PON OFF Device is not registered to the EPON system on 3 ERNEUTE Blink Device is registering ON WAN is effective WAN 4 WAN _ OFF WAN is ineffective ON WiFi turn on o WIFi OFF Device is power off or WiFi turn off Blink WiFi turn on and with ongoing data transmission ON Device has registered to the soft switch but without ongoing data transmission FXS1 Pots 6 FXS2 OFF Device is power off or not registered to the soft switch Blink The port is with ongoing data transmission ETH ON Port is connected properly Ethernet ITV Of Port connection exception or not connected 7 cie Blink Port is sending or and receiving data ETH4 ON WPS client is connecting Pair 8 Pair OFF Does not use WPS or WPS client is connected LED turn off after 5 minutes of successful connection ON USB device is connected but without ongoing data transmission USB 9 USB OFF Device2. HG326E EPON HGU User Manua MANUAL DE USUARIO GEPON ONU HG326E Netelcom HG326E EPON HGU User Manual Chapterl Overview 1 1 Product Description HG326E terminal devices are designed for fulfilling FTTH and triple play service demand of fixed network operators or cable operators These boxes are based on the mature Gigabit EPON technology which have high ratio of performance to price and the technology of 802 11n WiFi 2T2R Layer 2 3 and high quality VoIP as well They are highly reliable and easy to maintain with guaranteed QoS for different service And they are fully compliant with technical regulations such as IEEE802 3ah and technical requirement of EPON Equipment V2 1 and above version from China Telecom Figure 1 HG326E 1 2 Application Chart A arme Internet Media Center EPON HGU ulti Service Router A Notebook Video Network management Server Figure 2 Application Chart D Netelcom HG326E EPON HGU User Manual 1 3 Technical parameters Technical item HG326E PON interface 1EPON connector SC single mode single fibre symmetric 1 25Gbps Wavelength Tx1310nm Rx 1490nm Optical interface SC connector 4x 10 100Mbps auto adaptive Ethernet interfaces 10 100M Full Half Duplex Interface RJ45 connectors 2x POTS RJ11 connectors Wireless Compliant with IEEE802 11b g n 300Mbps 2T2R one internal antenna and one external anten
3. LAN settings So oo ae oon ee Wireless Basic This page is used to configure basic features of wireless LAN port Including enable or disable wireless LAN port hide SSID from being scaned by AP set wireless network name SSID set channel frequency according to different country standards and so on Click on Save Apply to take effect the basic configuration of wireless Enable Wireless Hide Access Point Clients Isolation Disable WMM Advertise Enable Wireless Multicast Forwarding WMF BSSID 00 1D 2B F8 78 B1 Country UNITED STATES Max Clients WLAN Basic Menu displays the current configuration information Modify these parameters to change WiFi basic features D Netelcom HG326E EPON HGU User Manual Figure 10 VolP Basic VoIP Se oe General Settings VoIP Basic Settings VolP Advanced Input the VoIP parameters then dick the Start Stop button to save parameters and start stop the VoIP service Interface Name ny_ WAN v Note You must restart the VoIP service to take effect Region USA NORTHAMERICA m Note You must restart the VoIP service to take effect Proxy Server 22 10 113 30 Port 5060 External Proxy Server se Port 15060 Registering Server 22 10 113 30 Port 15060 Phone Number 83221133 4A 83221133 sd 133 Username fabci21 baz Password fees ptime Settings VoIP Basic Settings The configuration of the SIP general parameters Including registeri
4. after the device is restarted 7 D Netelcom HG326E EPON HGU User Manual Figure 8 WAN Connection Network Status I Network Security App Internet LAN WAN moes o Internet LAN VLAN Uplink Mode EPON v WLAN VLAN Connection Name Add WAN Connection M Rate Limited ose me Loop Test Enable Vian ra Vian ID FRS VLAN Mode Transparent v En ble QinQ Service Mode INTERNET EZ Port Binding IV Port_ 1 Port_2 Internet UN WAN TR oo Internet LAN VLAN WLAN VLAN Connection Name Rate Limited Loop Test Uplink Mode Mode Protocol Mode DHCP Automatically obtain an IP address from your ISP C Static Configure a static IP address supplied by your ISP PPPoE Select this option if your ISP uses PPPoE Netelcom HG326E EPON HGU User Manual Network gt Internet Menu By modifying these parameters can add a WAN connection Mode WAN connection mode Bridge or Route Enable Vlan unchecked means disabled 802 1p VLAN priority 0 7 Vian ID 1 4094 VLAN Mode Tag or transparent Tag means upstreams will be added a VLAN tag while transparent will not Enable QinQ if checked there will be double VLANs in upstreams Service Mode What service the WAN used for Port Binding Bind LAN port and SSID to WAN connection Protocol Mode Configuring a route WAN should specify protocol mode and an IP address etc Choose one method to get an IP address among DHCP static and PPPoE Figure 9 W
5. is power off or USB device is not connected Blink USB is with ongoing data transmission Table2 Panel lights Netelcom HG326E EPON HGU User Manual Figure 4 Back panel Port Type Function PON port Connect PON port with internet by SC type single mode optical fiber cable EXS port Connect the telephone with FXS port by telephone wire If you only P have one telephone you should use FXS1 port Ethernet Ethernet port Ethernet port Connect PC with EPON HGU Ethernet port by RJ 45 Cat5 cable PC with EPON HGU Ethernet port Connect PC with EPON HGU Ethernet port by RJ 45 Cat5 cable RJ 45 Cat5 cable WiFi pair button Press down WiFi pair button and keep 0 1 3 seconds for WPS function wireless pair WiFi turn on off WiFi turn WiFi turn on off WiFi WiFi Press down Press down WiFi turn on off and keep 3 seconds to enable disable WiFi turn on off and Press down WiFi turn on off and keep 3 seconds to enable disable WiFi 3 seconds to enable disable WiFi Press down reset button and keep 1 5 seconds to make the device Reset button Reset restart and recover from the factory default Settings USB port External USB port can connect to USB storage device Power port DC12 V Connect with power adapter Power turn on off Power turn on off Table3 Back panel Figure 5 Side panel i gt a mr i f Table 4 Side panel 2 4 Equipment List Contents Quantit
6. na LED 13 For Status of POWER PON LOS WAN WIFI POTS FE Pair USB Operating 5 C 55 C 10 90 non condensed condition storing condition 30 C 60 C 10 90 non condensed Power supply DC 12V 1 1 5A Power consumption lt 10W Dimension 185mmx135mmx45mm LxWxH Net weight 0 34Kg Table 1 Technical parameters Chapter Installation 2 1 Installation Requirements Installation Environment Requirements HGU equipment must be installed in the interior and to ensure the following conditions Confirmation at the HGU installation at sufficient space to facilitate cooling machine HGU suitable working temperature of 5 55 C humidity 10 to 90 Device workplace should avoid radio transmitters radar stations and high frequency interference from power equipment Equipment Installation 1 Installed on the desktop Place the machine on a clean bench this installation is relatively simple you can observe the following operation Ensure the smooth workbench Around the device enough space for heat dissipation Observation HGU equipment chassis two cruciform recess in accordance with the position of the groove installed two screws in the wall The original selected two mounting screws gently snap into recesses aligned 2 Mounted on the wall Slowly let go so that the device under the support of the screw hanging on the wall
7. ng server address proxy server address phone number username Figure 11 Update Software as oie RE ur are Device Manage Device Reboot Tools Update Software Update Image USB Backup Step 1 Obtain an updated software image file from your ISP SEAN SACAP Step 2 Enter the path to the image file location in the box below or click the Browse button to locate the Load Default image file Step 3 Click the Update Software button once to upload the new image file NOTE The update process takes about 2 minutes to complete and your DSL Router will reboot Software File Name Update Software Update image menu is used to update software Enter the path of the image file in the box and click Update Software botton then it will be reboot
8. y Contents Quantity HGU 1 pcs Power adapter 1 pcs User manual 1 pcs QC card 1 pcs Network cable 1 pcs Table 5 Equipment List Netelcom HG326E EPON HGU User Manual Chapter3 Web Management HG326E provides simple Web management functions including modifying WAN LAN WiFI Router or Bridge Mode Voip Firmware upgrades and other functions 3 1 Default configuration The following is the default device configuration information eLocal LAN access Username admin Password admin e LAN port management IP address 192 168 1 1 24 3 2 Basic Configuration Figure 6 Web Login Web login default username admin WEB Login password admin Username admin Password Submit Cancel Figure 7 LAN settings Status Network security Application Management Diagnose Internet LAN WLAN TR QoS TimeServer Route LAN Settings Configure the IP address and subnet mask click Save Apply button to save the LAN configuration data IP Address 192 168 1 1 Subnet Mask 255 255 255 0 C Disable DHCP server Enable DHCP server Beginning IP Address 192 168 1 2 Ending IP Address 192 168 1 254 Subnet Mask 255 255 255 0 Lease Time One Day Enable DHCP server relay DHCP server IP address IP Address and Subnet Mask LAN port IP address and mask DHCP option Enable or disable DHCP server and DHCP server relay Note DHCP server changes take effect
Download Pdf Manuals
Related Search