FL 1000 XT - Hide-a-lite
Contents
1. FL 1000 XT LED light generators for use with fibre optic lighting User manual Mounting and installation instructions Item no 0123 0050 0123 0053 0123 2050 0123 2053 0123 0040 0123 2040 99082088 30 09 2013 FL 1000 XT B 3000 K FL 1000 XT B 3000 R CRI 90 FL 1000 XT B US 3000 K FL 1000 XT B US 3000 K CRI 90 FL 1000 XT B 4000 K FL 1000 XT B US 4000 K Roblon Contents Introduction Product overview Technical data Installation Dimming US models only Mounting Installing in closed compartments Installing adjacent light generators Mounting filters Spare parts Accessories Troubleshooting CON DOOR WN i GEN N AR O Oo 1 Introduction Roblon FL 1000 XT light generators are designed for use outdoors with glass or PMMA fibre in all installation set ups including in closed compartments Follow the installation instructions correctly in order to ensure safe operation enhanced functionality extended lifetime for components uninterrupted illumination 2 Product overview FL 1000 XT light generator 28 gt 9 harness adaptor Two Allen keys Screws Wall plugs Power cord User manual FL 1000 XT B FL 1000 XT B US 3 Technical data Light port Fibre type Total power consumption amp 700 mA Light source power Supply voltage Supply voltage US Applied LED Light source lifetime CCT nominal CRIg Ra typical value Protecti2. cool for 15 minutes Try again Is the harness common end dirty Clean filter with damp cloth Dry with lint free cloth Ambient temperature max 45 Measured 50 mm from light generator Surface temperature max 73 Measured beside the screw when it has been running for min 1 hour Measure ambient temperature here Measure surface temperature beside the screw Roblon accepts no responsibility for possible errors in printed and electronic material Roblon reserves the right to alter or discontinue products without notice 2012 Roblon A S Roblon Roblon Lighting Tel 45 9620 3300 Nordhavnsvej 1 Fax 45 9620 3399 9900 Frederikshavn info roblon com Denmark www roblon com
3. insert the assembled inner part in the casing 10 11 12 Replace the O ring Insert the casing screws and tighten Replace the baseplate and screw in place 10 10 Spare parts Model designation Description LED FL 1000 XT LED module LED FL 1000 XT US LED module US models Philips 25W CC 220 240 V Philips 35W CC 120 277 V Driver US models 0129 4004 0129 4005 0129 3000 0129 3001 11 Accessories CTC Filter A 500K CTC Filter A 900K CTC Filter A 1200K Colour Filter A yellow Colour Filter A green Colour Filter A blue Colour Filter A red Red filter 0126 1007 Bracket that can be Mounting bracket padlocked 0126 7000 11 12 Troubleshooting Trace the problem No light Is the power on Turn the power on Is the power cord connected Connect the power cord properly properly Is the light generator too hot Check it is installed according to the instructions Switch generator off Let it cool for 15 minutes Try again pis the LED working d ReplacetheleD gt Light switches on and off Is the light generator too hot Check it is installed according to the instructions Switch generator off Let it cool for 15 minutes Try again Light output has Has the light been dimmed via a Increase brightness using dimmer diminished dimmer switch switch Is the light generator too hot Check it is installed according to the instructions Switch generator off Let it
4. on rating Driver type Driver lifetime Dimmable Thermal protection Cooling system Noise level Ambient temperature Material Dimensions L x H x W Weight Safety Y or 28 mm PMMA Glass 24 W 19 3 W 220 240 V 50 60 Hz 120 277 V 50 60 Hz LUXEON S1000 LXS8 PW30 3 000 K LUXEON S1000 LXS8 PW40 4 000 K 50 000 hours 3 000 K 85 IP65 Integrated electronic 50 000 hours Trailing edge 1 10V US models Automatic decrease Natural convection N a 20 C to 45 C Aluminium POM 298 x 193 x 95 mm 2 3 kg CE 4 Installation 1 Use the Allen key to loosen and remove the 28 gt 9 harness adaptor that is mounted in the light port For use with 28 harness The generator is now ready for installation For use with 9 harness Place the 28 gt 9 harness adaptor on the harness common end Remove the plastic plug on the baseplate directly below the light port Insert the common end fully in the light port Tighten the screw on the base with an Allen key Insert the plastic plug Ensure all installation and ventilation requirements are met Connect the power cord to the mains 5 Dimming of 01232050 1 Ensure the dimmer is compliant with 1 10V US models See Dimmer selection guide for FL 1000 models on www roblonlighting com 2 Remove the plastic plug 3 Screw in the cable gland 4 Guide the dimmer cable through the cable gland gt Use a cable tie to
5. secure the cable s position 2 3 4 6 Mounting 6a Surface mounting 1 Attach to surface using two screws in the baseplate holes 2 Vertical installation to maintain IP 65 protection mount with the light port facing down 170 mm bet 26 mm TP gt gt 9 holes ay p 6a Bracket mounting 1 Attach the bracket not supplied see Accessories to the surface using two SCrevys 2 Mount the light generator on the bracket Q 140 mm w between O 6 mm DR holes 7 Installing in closed compartments Requirements Enough space to allow natural heat transmission through surfaces Surfaces should not be insulated Air volume per light generator minimum 0 03 m Ventilation holes per light generator with min 20 cm air inlet and min 20 cm air outlet Max ambient temperature 45 C 8 Installing one or more light generators Requirement min 100 mm distance between adjacent light generators in order to ensure sufficient heat transmission 100 P 9 Mounting filters Colour filters not supplied CTC filters not supplied CO NO In ES tu N SO Unscrew and remove the baseplate Remove the casing screws Remove the O ring Carefully detach and manoeuvre the assembled inner part out of the casing Unscrew the plastic front part Assemble the filter and bracket Mount the assembled filter in the detached front part Screw the front part back on Carefully
Download Pdf Manuals
Related Search