Installation and Maintenance Manual EX12*-STA1-XP Series
Contents
1. operating environment of the protection structure Avoid using IP40 where water or oil etc can be splashed IP4O is achieved by mounting on manifold solenoid valve and process wire entry corecily Cary out regular checks to confirm correct operation Safety may not be maintained by unintentional malfunction or incorrect operation A warninc The product specified here is designed to be used in standard factory automation equipnrent Do not use in machinery and or equipment where operators may be injured and malfunction or failure may cause loss of life Do not disasserrble to repair or modify the product Item Specifications Model EX120 STA1 xP EX121 STA1 xP EX122 STA1 xXP Output point 16 points Output style Transistor style NPN open collector style Connecting load DC 24V Solenoid valve with lamp surge voltage protection drait of 2 1W or less Residual voltage 0 4V or less Power supply voltage DC24V 10 5 Current consunption 0 3A or less inside unit Weight or less 170g 190g 180g Operating ambient tenperature O 50 C Operating arrbient humidity 35 85 RH No dew allowed Vibration resistance 5G According to JIS C0912 Inqpact resistance 10G According to JIS C0911 Noise resistance 1000Vp p pulse width 145 leading 1nS Withstand voltage AC1000V 50 60Hz for 1 min between the terminal and the case Insulation resistance More than 2MQ or more DC500V between the tervin2. O604VEng r This manual should be read in conjunction with the curent product catalogue Safety Instructions These safety instructions are intended to prevent a hazardous situation and or equipment danrage These instructions indicate the level of potential hazard by laba of CAUTION WARNING To ensure safety be sure to observe ISO JIS and other safety practices A CAUTION Operator error could result in injury or equipment damage A WARNING Operator error could result in serious injury or loss of life A caumon Thoroughly read this manual and operate the product within the spec ified range Follow the instructions Do not drop or inqpart any inqpact to the product Use within specified voltage range Use outside of specified voltage will cause malfunction darrage to unit electric shock and fire Do not touch the terminals or intemal drauit board while they are energized It may cause malfundion darrage to unit and dectric shock Installation and Maintenance Manual EX12 STA1 XP Series OMRON SYSMAC C CV Series SYSBUS Wire System For future reference please keep this manual in a safe place Use within operating ambient tenperature Do not use where tenper atures can rapidly change even though it is within the specifications Foreign objects should be prevented from entering the product Contarrination by foreign objects such as wire chips will cause fire breakage and malfunction Use within the
3. al and the case Operating atmosphere No conosive gas Protection dass IP40 This S unit is able to connect to OMRON Corp PLG SYSVIAC QOV series SYSBUS Wire sytem This 9S unit has 16 output points 1 station Maxum is 512 O points 32 stations per PLC master unit The following master unit is required to operate SYSBUS wire system C500 RM201 C200H RM201 Note Refer to the OMRON Corporation User Manual for full details Applicabi lenoid valves Applicable solenoid valve VQ1000 VQ2000 VQ1000 VQ2000 SX3000 SX5000 SY3000 SY5000 amp B000 SX5000 SY3000 SY5000 Si unit EX120 STA1 XP EX121 STA1 xP EX122 STA1 XP Refer to the catalogues for each solenoid valve for details caumon If solenoid valves other than those stated in the chart above are used VIC offers no guarantee against malfunction of the S unit nor if any load other than solenoid valves is used Teminal name Connected to 24V 24V supply power cable Ov OV supply power cable Transmission path Transmission path FG Grounding conductor and shield Wiring Fig V A camon Power of the produt and all other equipment should be tumed off while wiring Tighten the wiring with tenvinal screw completely The teminal sew for connection is M3 Use appropriate ainp sye teminal for the temina screw Short drait fire and malfundion will be caused if teminal screw is not tightened enough Avoid
4. ase contact your local SMC office see bdow When you enquire about the product please contact the following SMC Corporation ENGLAND Phone 01908 563888 TURKEY Phone 212 2211512 MALY Phone 02 92711 GERMANY Phone 6103 402 0 HOLLAND Phone 020 5318888 FRANCE Phone 01 64 76 10 00 SAMTZERLAND Phone 052 396 31 31 SWEDEN Phone 08 603 07 00 SPAIN Phone 945 184100 AUSTRIA Phone 02262 62 280 Phone 902 255255 IRELAND Phone 01 4501822 GREECE Phone 01 3426076 DENMARK Phone 70 25 29 00 FINLAND Phone 09 68 10 21 NORWAY Phone 67 12 90 20 BELGIUM Phone 03 3551464 POLAND Phone 48 22 6131847
5. incorrect wiring It nay damage the product and or other equipment Ensure that the FG tenvinal is correctly earthed Power with correct capacity should be prepared by considering the in rush current when starting Influence of noise should be avoided for the wiring Wiring should be separated from power cables and high voltage calles Wiring of the signal cables Wiring of twisted pair cable should follow the drawing shown in Fig 1 Use cable recommended by OMRON Corporation Z casmon Products est that can only be mounted from one side of the meni fold Please refer to the qurrent catalogue for each solenoid valve When the number of stations on a VQ SX manifold are 8 or less the intemal wiring will default to DOUBLE solenoid wiring Q eeo B 5 8 cee A 7 eeo Va A G6 eee A 5 eee Va 3 4 s A 3 eeo B z 2 eeo A l B i O eee A g unit sain Output No U S unit Output No a Stich Q eee B A z 8 eee A AETA Va Single 4 G6 eee A Pps Va Single 3 4 e A 3 eeo B 3 2 eeo A Leee B q O eee A D Fig2 2 Non standard wiring nixed wiring Mixed wiring is available as a non standard option If nixed wiring is specified the positions of the single and double solenoids on the man ifold must be indicated when ordering LED Nane Content RUN Normal operation PLC Operation Light TR Nom al transmission Blink ERR Abnoma
6. l transmission Light Figl1 Wiring of power supply Ensure that the power is within the specified voltage range Ensure that the cable is capable of supporting the solenoid and S unit in tems of rating Corresponding SI unit output and solenoid valve L Standard wiring The outputs of the I unit are assigned from the D side down solenoid valve in the order O 1 2 etc The S unit can be mounted fromthe direction of the D side or the U side up Adidiress setting Fig 3 Power should be tumed off to set address Opan the 9 unit cover adjust by tuming the address setting switch using a small bladed screwdriver Setting range is O 31 It is not pos sible to set address overlap End station setting Hold Ceear Fig3 Set the address as follows by SW1 5 Node address SWL AN2 MB awm SWB Part identification Fig 4 Name of each part and dimension 3 EX122 STA1 xP 2 EX121 STA1 XP ESETI PUszetz Fig4 Hold Clear setting Set whether maintaining S unit output condition or tune off all of it when communication error is generated Hold Clear setting Swe Clear 1 Hold o Tum on both SVV7 and 8 when unit is at the end station oO oO Oo o o Oo 1 1 oO ie ie oO End station setting AN7 Ss 2 Oo 1 o o oO ON 1 1 3 1 1 o o oO OFF Oo oO 2 For additional information ple
Download Pdf Manuals
Related Search