LITEMAX SLD0832 LCD Monitor
Contents
1. VERSION ADS FBBGDYA 1 0 S Auto Adjust Choose this option and the AD5766 will adjust to the optimal horizontal and vertical frequency You will see Auto tune on the screen for around 3 seconds Clock If you are not satisfied with the Auto tune result you can adjust manually by pressing Clock Using this will make the image wider Phase If double images appear around the characters choose Phase to remove them HPos You can shift the screen horizontally using this function Vpos You can shift the screen vertically using this function Exit Back to normal screen Page 8 On the Tools sub menu you will see 5 icons TIMING 102447650100 Hz VERSION ADS FbBGDYA 1 0 S OSD Control Selecting this option brings you to 4 more options TIMING 102417680100 Hz VERSION ADS FBBGDYA 1 0 a Osd_time Select time for the OSD user interface to stay on screen for 2 sec to 16 sec Default is 6 sec Osd_HPos Moves the OSD user interface horizontally on screen Osd_VPos Moves the OSD user interface vertically on screen Exit back to main menu Factory _Reset By pressing this the screen will revert to factory settings and the previous settings will be deleted Sharpness Sharpen characters Page 9 P Dos_mode Gxf_mode For some old programs which use 640x400 and 720x400 DOS Mode and graphics mode This option needs to be selected manually Ex2. that Video Signal cable from the Display has been securely and correctly connected Check that Video Card is firmly seated in card slot of Computer motherboard Check that the video input from the Video Card falls within the timing range Abnormal image Check that the video input from the Video Card falls within the timing range Check that Video Signal Cable from the Display has been securely and correctly connected to the Video Connector at the rear side of the Computer Colors of image on Check that Video Signal Cable from the displays screen are abnormal has been securely and correctly connected to the 15 pin Video Connector at the rear side of the computer Disturbances on 1 OSD adjustment is incorrect Please consult Screen Page 11 section for OSD screen adjustment procedures X Please contact your local authorized distributors retailers if you run into other unsolved problems The Display Timing Applicable video timing The following table lists the better display quality modes that the LCD monitor provides If the other video modes are input the monitor will stop working or display unsatisfactory picture quality VESA Modes Mode Resolution Total Nominal Nominal Nominal Frequency Frequency Pixel Clock 0 5KHz 0 5KHz MHz pos 720x400 70Hz 900x449 31 469 70 087 28 322 640x480 60Hz 800x525 31 469 59 940 25 175 Page 12 Specification Model No LO0832 SNB A
3. 01 Display Area 228 H x 162 V mm Pixel Arrangement RGB Red Green Blue vertical stripe Pixel Pitch 0 2025 H x 0 0675 V mm Viewing Angle At the contrast ratio 10 1 e Horizontal Left side 70 typ Right side 70 typ e Vertical Up side 50 typ Down side 70 typ Color Gamut At LCD panel center 60 typ against NTSC color space Ton black 10 white 90 Language Management eer ery Specifications subject to change without notice Page 13 Product Safety Precautions Follow all warnings and instructions marked on the product Do not use this product near water This display should be installed on a solid horizontal base When cleaning use only a neutral detergent cleaner with a soft damp cloth Do not spray with liquid or aerosol cleaners Do not expose this display to direct sunlight or heat Hot air may cause damage to the cabinet and other parts Adequate ventilation must be maintained to ensure reliable and continued operation and to protect the display from overheating Do not block ventilation slots and openings with objects or install the display in a place where ventilation may be hindered This display should be operated from the type of power source indicated on the AC DC adapter Do not install this display near a motor or transformer where strong magnetism is generated Images on the display will become distorted and the color irregular Do not allow metal pieces or obj
4. K ELITE MAX ENRICH YOUR VISUAL WORLD Sunlight Readable LCD LITEMAX SLDO832 LCD Monitor User s Manual 1st Edition 11 16 2006 All information is subject to change without notice Approved by Checked by Prepared by LITEMAX Electronics Inc 8F 2 No 133 Lane 235 Bau chiau Rd Shin dian City Taipei County Taiwan R O C Tel 886 2 8919 1858 Fax 886 2 8919 1300 Homepage http www litemax com tw Page 1 Product Description Congratulations on purchasing this new generation monitor This monitor is for industrial and professional use contributing to its industrial and professional features Also this monitor incorporates high quality display into a small light weighted but strong module for particular extreme environment You will certainly benefit from this monitor in many ways to name some of them comfort safety health and environmental protection Product Features R High contrast color TFT LCD display support resolution up to SVGA 800 x 600 Compatible with IBM VGA VESA standards LED backlighting Perfect for transportation application Support analog S Video amp Audio input Support NTSC or PAL Video in function High sensitive USB Touch Panel Support VESA 75 75 x 75mm standard mounting holes for wall mount or ARM mounting application OSD cover to prevent unauthorized change of OSD m 2Wx2 speakers Standard model m 8 LED backlight TFT liquid crystal monitor Cleaning G
5. ects of any kind fall into the display from ventilation holes Do not attempt to service this unit yourself Removal of the display cover may expose you to dangerous voltage or other risks Refer all servicing to qualified service personnel Unplug this product from the wall outlet and refer servicing to qualified service personnel in the event that Liquid is spilled into the product or the product is exposed to rain or water The product does not operate normally when the operating instructions are followed The product has been dropped or the cabinet has been damaged The product exhibits a distinct change in performance indicating a need for service ota DE Power cord or plug is damaged or frayed General specifications for the LCD The following items are neither defects nor failures Response time luminance and color gamut may be changed by ambient temperature The LCD may be seemed luminance uniformity flicker vertical seam and or small spot by display patterns Optical characteristics e g luminance display uniformity etc gradually is going to change depending on operating time and especially low temperature because the LCD has cold cathode fluorescent lamps Page 14
6. ently wipe the screen with a clean camel hair lens brush or a soft clean lint free cloth This removes dust and other particles that can scratch the screen Do not apply pressure to the screen surface when wiping it clean Do not pour or spray any liquid directly onto the screen or case of the LCD monitor Chemical cleaners have been reported to damage the screen or case of the LCD monitor Page 2 Mechanical Drawing 230 32 7 Bezel Upen 164 5 Active Area 161 8 SPEAKERCE WD 185 sT 96 CU os co ce a 0 I OU D O CL UU L 2 lt L RI S u CO LJ lt L Page 3 Setting Up 1 S video 2N GA 3 USB S A Ra b f ma f SD J 4 Power RS j J 6 Key c K j DAA F ie 7 5 Audio gt f Power Lamp 1 S Video This can be connected with the S video output of other device 2 VGA Input This can be connected to PC or other device 3 USB Touch This can be connected to PC or other device 4 Power Cable 5 Audio in 6 Hot Key 7 Power Lamp OSD Keyboa 1 Power 2 LED 3 MENU Enter 4 LEFT 5 RIGHT 6 AUTO EXIT This is for connecting the power adapter This can be connected to PC or device 3 5mm STEREO PLUG BLACK Input source switching hot key Power status instruction rd AMBER 52 4 5 A e Ye L L GU LO j Ei eo T L JI IC 1 REEN C HEN 7 C RIGHT C UTO NTR Turn ON OFF monitor Power status instructi
7. it OSD Lock Function It is possible to lock all the OSD buttons to prevent unauthorized changes to occur by pressing Menu and right gt buttons simultaneously You will see the lock icon below on the center of the screen for 3 seconds If any button is pushed after the lock function is initiated the below icon will appear on the screen To release the OSD lock press Menu and Right gt The below icon will appear on the center of the screen for 3 seconds Now all OSD keys are active again Page 10 Power LED Display amp Power Saving General Power Saving Mode Mode Power LED Color Power Consumption Stand by 30W max lt 4W USB model lt 4W USB model lt 4W USB model Troubleshooting Tips In the event that you experience trouble with your Display check the following items before contacting the dealer from whom the Display was purchased The most common problems usually involve an incorrectly an incorrect connection from the Video Card to the Display We recommend that you also consult your Video Card User s manual during the Troubleshooting Procedure Do not exceed the maximum refresh rate recommended for the display No image on display Check that power cord of the Computer has been screen connected securely into wall outlet or grounded extension cable or strip Check that power switch of the Display has been pressed and LED on the front of Display is lit Check
8. mum luminance to fit your application OPTION Page 5 aq Contrast Press menu and right buttons to adjust the contrast from 0 to 100 To adjust from 100 to 0 press menu and the left buttons Exit You can exit this sub menu back to normal screen TIMI 10247 6e en UU Hz VERSION ADS FbBGDYA 1 0 a VGA Analog RGB VGA input DVI Digital DVI input AV 1 AV1 Composite input S Vide S Video S Video input Exit Exit You can exit this sub menu back to the beginning TIMING 1024176860100 Hz VERSION ADS FBBGDYA 1 0 n Page 6 There are 3 options for Sound sub page Audio Volume Audio volume adjustment eo UnMute Mute You can mute the speaker by pressing this option Exit back to the beginning menu TIMING 102417620100 Hz VERSION ADS FBBGDYA 1 0 Auto Color By navigating over to the Auto Color option optimal color performance is invoked RB SRGB Windows standard color setting TIMING 102417680100 Hz VERSION ADS FbBGDYA 1 0 pA Color Temperature You have 3 options in this selection Color Temperature User Define Default is 100 for R G and B Page 7 Gra Color Tempture_6500K Warm color scheme Goo Color Tempture_9300OK Cold color scheme Exit back to the normal screen Go to the Image page and you will see the below picture TIMI G 102417680100 Hz
9. on 1 Open OSD Function Menu 2 Enter OSD function Move left to next icon or function as pressing this button Move right to next icon or function as pressing this button 1 Auto tuning 2 Exit OSD menu Page 4 OSD menu By pressing the menu button you will see the below picture Across from timing you will see resolution frequency and V frequency of the panel Version shows the firmware control version These cannot be altered by the user TIMI G 1024x bem OO Hz VERSION ADS BEGDYVA V1 0 m There are 7 sub menus within the OSD user interface Brightness Signal Select Sound Color Image Tools and Exit When you press the menu button you enter the Brightness sub directory In this directory you will see 4 selections oa press menu rea press menu on press menu rea press menu ee OSD Brightness fea press right key Press the menu once to adjust the brightness Press left to dim down the brightness to 0 press right to increase the brightness to A 00 Ambient light sensor Press this Icon for auto dimming OPTION To use this option the Litemax ambient light sensor needs to have been installed Potentiometer Navigate to this icon to adjust the VR function OPTION Ambient light sensor with OSD offset To set minimum brightness level based on ambient light fea Press right key oe Press menu once to adjust mini
Download Pdf Manuals
Related Search