USER MANUAL - Speed Passion
Contents
1. Sized Q RC Technology Revolution USER MANUAL Sensorless Brushless Speed Controller for 1 18 1 16 On Road Car Off Road Truck and Drift RC car User Manual of Emotion Series Brushless Speed Controller Ver 12192009A Page 7 Thanks for purchasing Emotion Electronic Speed Controller ESC High power system for RC model can be very dangerous so we strongly suggest you read this manual carefully In that we have no control over the correct use installation application or maintenance of our products no liability shall be assumed nor accepted for any damages losses or costs resulting from the use of the product Any claims arising from the operating failure of malfunctioning etc will be denied We assume no liability for personal injury consequential damages resulting from our product or our workmanship As far as is legally permitted the obligation to compensation is limited to the invoice amount of the affected product Specially designed for RC car with excellent start up acceleration and linearity features Compatible with sensor less brushless motor and with Most sensord motor Use top quality electronic components to enhance the current endurance ability of the ESC 3 running modes Forward Backward mode Forward Reverse with brake Forward Reverse with out brake 4 steps of maximum reverse force adjustment Proportional ABS brake function with 4 steps of maximum brake force adjustment 8 steps of drag br2. 3 seconds LED flashes once and motor LED flashes twice and motor LED flashes thrice and motor emits Beep tone emits Beep Beep tone emits Beep Beep Beep tone backward zone Alert Tones 1 Input voltage abnormal alert tone The ESC begins to check the input voltage when power on if it is out of the normal range such an alert tone will be emitted beep beep beep beep beep beep There is 1 second time interval between every beep beep tone 2 Throttle signal abnormal alert tone When the ESC can t detect the normal throttle signal such an alert tone will be emitted beep beep beep There is 2 seconds time interval between every beep tone Protection Function 1 Low voltage cut off protection If the voltage of a lithium battery pack is lower than the threshold for 2 seconds the ESC will cut of the output power Please note that the ESC cannot be restarted if the voltage of each lithium cell is lower than 3 5V For NiMh NiCd battery packs if the voltage of the whole NiMh NiCd battery pack is higher than 9 0V but lower than 12V it will be considered as a 3 cell lithium battery pack if it is lower than 9 0V it will be considered as a 2 cell lithium battery pack For example if the NiMh battery pack is 8 0V and the threshold is set to 2 6V Cell so it will be considered as a 2 cell lithium battery pack and the low voltage cut off threshold for this NiMh battery pack is 2 6 2 5 2V 2 Over h
3. is also called minimum brake force and it refers to the force when the throttle stick is located at the initial position of the backward zone The default value is equal to the drag brake force so the brake effect can be very smooth 2 9 Throttle Neutral Range Please see the following illustrations to adjust the neutral range as your like User Manual of Emotion Series Brushless Speed Controller Ver 12192009A Page 7 2 10 AMTS There are Top point of maximum throttle many differences among structures and parameters of z different brushless motors so a i eee fixed timing ESC is difficult to A S OS Ae enone Top point of compatible with all brushless E N tr l pint wh maximum brake motors It is necessary to make N i Sa een the timing value programmable S Ce zone Please select the most suitable BER Brake and backward zone Forward Neutral point timing value according to the 3 ate nn Neutral zone H i op point o n T H Gale i Top point of maximum brake maximum throttle brings out higher power output but the whole efficiency of the system will be slightly lower down 2 11 Over Heat Protection If the function is activated the output power will be cut off when the temperature of the ESC is up to 95 Celsius degrees for more than 5 seconds When the protection happens the Green LED will flash in such a way Flashes Flashes Flashes 3 Reset All Items To Default Valu
4. 5 3 75 0 7 50 0 11 255 BEM 18 75 22 500 26 250 TATA for sensorless motor 10 10 Over heat Protection heat Protection 95 Degree Non Protection Protection Attention The italics texts in the above form are the default settings 2 Programmable Values 2 1 Running Mode With Forward with Brake mode the car can go forward and brake but cannot go backward this mode is suitable for competition Forward Reverse with Brake mode provides backward function which is suitable for training also forward Reverse which suitable for rock crawler Note Forward Reverse with Brake mode uses Double Click method to make the car go backward When you move the throttle stick from forward zone to backward zone for the first time the ESC begins to break the motor the motor speeds down but it is still running not completely stopped so the backward action is NOT happened now When the throttle stick is moved to the backward zone again The 2 click if the motor speed is slowed down to zero i e stopped the backward action will be occurred The Double Click method can prevent mistakenly reverse when the brake function is frequently used in steering By the way in the process of braking or reverse if the throttle stick is moved to forward zone the motor will regain forward running at once 2 2 Drag Brake Force Set the amount of drag brake applied at neutral throttle to simulate the slight braking effect of
5. O y YOUMS uay pue 9S3 y yo Yyoyms BurwwesBoid ysiui4 Press SET key to choose the value the flash times of RED LED means the serial Enter the N item number of the value 1 time means the 1st SET key value 2 times means the 2nd value Green LED flashes for N times Release Note In the program process the motor will emit Beep tone at the same time when the LED is flashing If the N is bigger than the number 5 we use a long time flash and long Beep tone to represent 5 so it is easy to identify the items of the big number For example if the LED flashes as the following A long time flash a short time flash Motor sounds Beep Beep the No 6 item A long time flash 2 short time flash Motor sounds Beep Beep Beep the No 7 item A long time flash 3 short time flash Motor sounds Beep BeepBeepBeep the No 8 item And so on Programmable Items list User Manual of Emotion Series Brushless Speed Controller Ver 12192009A Page 7 Programmable Programmable Value Items a a a a a 3 a a eae Basic ltems Forward Only aceite orward R 1 Running Mode with Brake with Brake everse 2 Drag Brake Force o 100 3 Low Voltage 3 0V 3 2V 3 4V Cut Off Threshold Non Frotrcicn ZGVS eee Cell icell Cell Ef Very 4 Star Mode Pune CM PNRA Advanced liems 50 M a o Norman MEAT M B S S 9 Timing 0 00
6. a neutral brushed motor while coasting 2 3 Low Voltage Cut Off The function is mainly to prevent the lithium battery pack from over discharging When using lithium battery pack please set the suitable value for low voltage protection as your like WARNING Never use the default value Non protection for lithium battery 2 4 The ESC monitors the battery s voltage at any time if the voltage is lower than the threshold the output power will be cut off 2 5 DRRS Mode Select from soft to very aggressive start mode as you re like Please note that if you choose Aggressive or Very Aggressive mode you d better use good quality battery pack with powerful discharge ability otherwise these 2 modes cannot get the bursting start effect as you want If the motor cannot run smoothly the motor is trembling it may caused by the weak discharge ability of the battery pack please choose a better battery or increase the gear rate 2 6 Maximum Brake Force The ESC provides proportional brake function The brake force is related to the position of the throttle stick Maximum brake force refers to the force when the throttle stick is located at the top point of the backward zone A very large brake force can shorten the brake time but it may damage the gears 2 7 Maximum Reverse Force Sets how much power will be applied in the reverse direction Different value makes different reverse speed 2 8 Initial Brake Force It
7. a period of 30 days form the original date of purchase Verified by sale receipt dated User accepts all resulting liability We reserve the right to modify warranty provisions without notice Warranty does not cover incorrect installation components worn by use or any damage caused by crash flooding or natural disaster The company has no control over the installation of this product no liability may be assumed nor will be accepted for any damage resulting from the use of this product User Manual of Emotion Series Brushless Speed Controller Ver 12192009A Page 7 Sneed Q RC Technology Revolution USER MANUAL Sensorless Brushless Speed Controller for 1 18 1 16 On Road Car Off Road Truck and Drift RC car
8. ake force adjustment and 4 steps of initial brake force adjustment DRRS Digital Racing Respond System Also called Punch from Level 1 soft to Level 9 very aggressive 8 Multiple protection features Low voltage cut off protection for lithium or nickel battery Over heat protection Throttle signal loss protection Motor blocked protection 9 8 steps adjustment of AMTS Advance Multi timing System design suitable for different brands of brushless motor with give you the best performance for both the ESC and motor 10 Waterproof and dustproof 11 Easily program with only one button and compatible with pocket sized SMART ESC program card OCT Gos Cont Current 20A Burst Current 100A Resistance 0 005 ohm Suitable Car Car Rock Crawler 2WD Off Road Suitable gt 10 000 brushless motor Brushless Motor 4 9 Cell Ni xx NiMh or NiCd or 2 3 Cell Li Po 1 For 4 6 Cell Ni xx You needn t change the fan combined with the ESC Battery 2 For 7 9 Cell Ni xx You must change the fan combined with the controller because it cannot work with such a high voltage so please choose a high voltage fan or supply the fan from the receiver 5V Note1 BEC Output 6V 1 5A Motor Type Sensor less Brushless Motor Dimension 31 5mm 27 5mm 24mm The height of fan is not included Weight 15g Without wires Note1 For information about the high voltage fan please r
9. eat protection When the temperature of the ESC is over 95 Celsius degrees for 5 seconds the ESC will cut off the output power You can disable the over heat protection function for competition race 3 Throttle signal loss protection The ESC will cut off the output power if the throttle signal is lost for 0 2 second User Manual of Emotion Series Brushless Speed Controller rouble Shooting Ver 12192009A Page 7 Possible Reason Solution After power on motor can t work no sound is emitted The connections between battery pack and ESC are not correct Check the power connections Replace the connectors After power on motor can t work but emits beep beep beep beep alert tone Every beep beep has a time interval of 1 second Input voltage is abnormal too high or too low Check the voltage of the battery pack After power on motor can t work but emits beep beep beep alert tone Every beep has a time interval of about 2 seconds Throttle signal is abnormal Check the transmitter and the receiver Check the wire of the throttle channel The motor runs in the opposite direction The wire connections between ESC and the motor need to be changed Swap any two wire connections between the ESC and the motor The motor suddenly stops running while in working state The throttle signal is lost Check the transmitter and the receiver Check the wire o
10. efer to the brief introduction on page 3 Begin To Use The New ESC 1 Connect the ESC motor receiver battery eee and servo according to the following diagram A power wire ao Se And wires on the ESC are connected A i with the battery pack and A B and C are connected with the motor wires The SET button is used for programming the ESC The control cable of the ESC trio wires with black red and white color is connected with the throttle channel of the receiver Usually CH2 The A B C wires of the ESC can be connected with the motor wires freely without any order If the motor runs in the opposite direction please swap any _ two wire connections Note You can use the transmitter to set the Brushless Motor Input TH channel ty Gn2y Red power wire battery positive Switch j Receiver Servo plugged into steering ch 1 lt User Manual of Emotion Series Brushless Speed Controller Ver 12192009A Page 7 throttle channel to the Reverse direction and then the motor will run oppositely Please calibrate the throttle range again after changing the direction of throttle channel 2 Throttle Range Setting Throttle Range Calibration In order to make the ESC fit the throttle range you must calibrate it for the following cases otherwise the ESC cannot work properly 1 Begin to use a new ESC 2 Begin to use a new transmitter 3 Change the settings of ne
11. es At any time when the throttle is located in neutral zone except in the throttle calibration or parameters program process hold the SET key for over 3 seconds the red LED and green LED will flash at the same time which means each programmable item has be reset to its default value Exemption Clause Speed Passion does not have control over the installation or use of this product therefore no liability for any damages incurred in its use will be accepted Operation of this product is at the user s risk The use of R C models requires a degree of skill If you are a beginner please consult the advice of an experienced user to prevent injury to goods or other persons Caution Do not operate the ESC at voltages lower than 6V or higher the 14 8V battery damage to the ESC can result When mounting the brushless motor in your car pay careful attention to the length of the motor screws they must not exceed 4 0mm in depth longer than this and internal damage to the motor will result which will void the product warranty Ensure all connections are secure before using this product Speed Passion reserves the right to modify the design appearance and specification of the product without notice ESC Warranty period 90 days limited warranty Not including parts 2 month return time for any repair or services Limited 30 days warranty This product is guaranteed to be free from defects in materials or workmanship for
12. f the throttle channel The ESC has entered the Low Voltage Protection Mode Replace the battery pack Random stop or restart or irregular working state Some connections are not reliable Check all the connections battery pack connections throttle signal wire and motor connections etc There is strong Electro Magnetic interference in flying field Reset the ESC to resume normal operation If the function could not resume you might need to move to another area to run the car 1 Program card Program card is standard accessory which came with the ESC It has a friendly user interface The process of programming the ESC becomes quite easy and fast with this pocket sized device When the programmable value needs to be changed please just plug the control wires of the ESC trio wires with black red and white color into the socket of the program card The socket is on the right corner and marked with and then connect the main battery pack to the ESC each item s value will be shown on the program card Use ITEM and VALUE buttons to select the programmable items and new values and then press Ok button to store the new settings into the ESC oUu gz EO mS _ Program The ESC 1 Program Method User Manual of Emotion Series Brushless Speed Controller Ver 12192009A Page 7 Turn off the ESC Turn on the transmitter Hold the SET key Sanne Enter the corre
13. sponding Press the SET key to choose the programmable item the programmable value the RED LED RED LED flashes for several flashes for several times the times times the times presents the presents the serial number of the value current value of this item you are choosing Red LED flashes for 1 time to choose Green LED flashes Forward with brake for 1 time Release Running Mode Press Red LED flashes for 2 times to choose SET key SET key Forward Reverse with brake Enter the 1st item Hold SET key for 3 seconds Red LED flashes 1 time choose 0 Green LED flashes for 2 times Enter the 2nd item Red LED flashes 2 times choose 5 Release Drag Brake Force Press Red LED flashes 3 times choose 10 SET key SET key Red LED flashes 4 times choose 15 Red LED flashes 5 times choose 20 Red LED flashes 6 times choose 25 Red LED flashes 7 times choose 30 Hold SET hey for 3 seconds Red LED flashes 8 times choose 40 Release Red LED flashes 1 time choose None Green LED flashes seTkey Enter the 3rd item Red LED flashes 2 times choose 2 6V for 3 times Low Voltage Cut Off gt Red LED flashes 3 times choose 2 8 V SET key Red LED flashes 4 times choose 3 0V Red LED flashes 5 times choose 3 2V Red LED flashes 6 times choose 3 4V Hold SET key for 3 seconds Hold SET key for 3 seconds U
14. utral position of the throttle stick ATV or EPA parameters etc There are 3 points need to be set they are the top point of forward backward and the neutral point The following pictures show how to set the throttle range with a Futaba transmitter 3 The LED Status in Normal Running a In normal use if the throttle stick is in A Switch off the ESC turn on the transmitter set the neutral range neither the red the direction of throttle channel to REV set the LED nor the green LED will light EPA ATV value of throttle channel to 100 b The red LED lights when the car is B Hold the SET key and then switch on the ESC run forward or backward and it will release the SET key when the red LED begins ae quickly tes ag is rina to flash c The green ights when the Please refer to the picture on the right side throttle stick is moved to the top point end point of the forward zone or 5 r Move the throttle stick to the Move the trottle stick to the Move the trottle stick to the C p 3 AU E to i neutral position end position of forward end position of backward steps shown in the picture on the 7 right side ES RX 1 Neutral point HA f N 2 End point of forward direction V N Uo 3 End point of backward direction D When the process of calibration is k k finished the motor can be started Press SET key the Green Press SET key the Green Press SET key the Green after
Download Pdf Manuals
Related Search