User Manual
Contents
1. is void if defects in materials or workmanship or damages re sult from repairs or alterations which have been made or attempted by oth ers or the unauthorized use of nonconforming parts the damage is due to normal wear and tear this damage is due to abuse improper maintenance neglect or accident or the damage is due to use of the Rear View Safety Inc system after partial failure or use with improper accessories Warranty Performance DURING THE ABOVE WARRANTY PERIOD SHOULD YOUR REAR VIEW SAFETY PRODUCT EXHIBIT A DEFECT IN MATERIAL OR WORKMANSHIP SUCH DEFECT WILL BE REPAIRED WHEN THE COMPLETE REAR VIEW SAFETY INC PRODUCT IS RETURNED POSTAGE PREPAID AND INSURED TO REAR VIEW SAFETY INC OTHER THAN THE POSTAGE AND INSURANCE REQUIREMENT NO CHARGE WILL BE MADE FOR REPAIRS COVERED BY THIS WARRANTY Warranty Disclaimers NO WARRANTY ORAL OR WRITTEN EXPRESSED OR IMPLIED OTHER THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS REAR VIEW SAFETY INC REAR VIEW SAFETY INC DISCLAIMS ANY IMPLIED WARRANTY OR MERCHANT ABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE AND ALL OTHER WARRANTIES IN NO EVENT SHALL REAR VIEW SAFETY INC LIABLE FOR ANY INCIDENTAL SPECIAL CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR ANY COSTS ATTORNEY FEES EXPENSES LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO FAILURE OF OR DEFECT IN ANY PROD UCT INCLUDING BUT NOT LIMITED TO ANY CLAIMS FOR LOSS OF PROFITS Reverse With Confidence 23 D2. standard rear view mirror that already exists in your vehicle The Backup Camera System should not be used as a substitute for the standard rear view mirror or for any other mirror that exists in your vehicle In some jurisdictions it is unlawful for a person to drive a motor vehicle equipped with a TV viewer or screen located forward of the back of the driver s seat or in any location that is visible directly or indirectly to the driver while operating the vehicle 0 REAR VIEW SAFETY Safety Information Please read the entire manual and follow the instructions and warnings carefully Failure to do so can cause serious damage and or injury including loss of life Be sure to obey all applica ble local traffic and motor vehicle regulations as it pertains to this product Improper installation will void manufacturer s warranty USAGE e The Rear View Camera System is designed to help the driver safely detect people and or objects helping to avoid damage or injury However you the driver must use it properly Use of this system is not a substitute for safe proper or legal driving Never back up while looking at the monitor alone You should always check behind and around the vehicle when backing up in the same way as you would if the vehicle did not have the Rear View Reverse With Confidence Camera System If you back up while looking only at the monitor you may cause damage or injury Always back up slowl
3. to set the brightness To adjust saturation press MENU Use arrows to choose desired camera and press MENU to select Once selected use arrows to set the brightness To adjust sharpness press MENU Use arrows to choose desired camera and press MENU to select Once selected use arrows to set the brightness To adjust day night press MENU Use arrows to choose desired mode and press MENU to select Once selected use arrows to change mode To change the name press MENU Use arrows to choose desired camera and press MENU to select Once selected use arrows to set the letters To adjust trigger source press to select Once selected use arrows to choose desired line and press To adjust trigger delay press MENU to select Once selected use arrows to choose desired camera and press To adjust distance grid press MENU to select Once selected use arrows to choose desired camera and press MENU Use arrows to set the distance To adjust grid position press MENU to select Once selected use arrows to choose postion and press MENU To set auto power press MENU to select Once selected use arrows to choose off or on and press MENU To reset press MENU to select Once selected use arrows to choose yes or no and press MENU To return to previous press REV when in menu To rotate screen press REV To adjust the volume pr
4. 7 Atlantic Avenue Brooklyn NY 11233 Tel 800 764 1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT SAFETY REVERSE WITH CONFIDENCE Reverse With Confidence e Before Beginning Installa Before drilling please check that no cable or wiring is on the other side of the wall Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use Keep all cables away from hot or moving parts and electrical noisy components We recommend doing a benchmark test before installation to insure that all components are working properly Step 1 Choose the monitor and camera locations Step 2 Install all cables in vehicle when necessary a 0 8 20mm hole should be drilled for passing camera cable through vehicles walls Install split grommets where applicable Step 3 Once all cables and wiring have been properly routed perform a system function test by temporarily connecting the system If the system seems to not be operating properly see troubleshooting page 22 0 REAR VIEW SAFETY Installation Guide Camera 1 Attach camera bracket close to rear marker lights centered on vehicle 2 Attach camera to bracket using screws provided and adjust the angle Cable Be sure to position the cable properly The aviation camera cable
5. Rear View Camera System 1Camera Setup Product Manual Installation Instructions Rear View Camera System Model 4 RVS 770613 SAFETY Rear View Safety Inc 2014 REVERSE WITH CONFIDENCE What s in the Box Color CCD Infra red Weather Proof Camera e 1 7 TFT LCD Color Monitor w Universal Mount Stand Wire e 1 3 Channel Multiplexer Control Unit 66 Camera Cable e 1 Remote Control Power Connection Wire Double RCA Power Converter to connect external audio video and power e 1 Screw Kit for installation 6 REAR VIEW SAFETY Table of Contents 4 Safety NOM HIM union 5 7 8 Before Beginning Installation Guide Wiring Camera Et Monitor 10 11 Installation Diagtatri etc 12 Installing th Monitor 13 SO 14 Splitting 15 POSO ii a 16 E Monitor Dimensions Monitor SpecifICatiODis 19 Camera DIMENSIONS 20 Camera 0 21 TroubleshiooUng uut ctae eade 22 WANG e cata aaa 23 24 Reverse With Confidence e Introduction Please read all of the installation instructions carefully before installing the product Improper installation will void manufacturer s warranty Congratulations on purchasing a Rear View Backup Camera System With this manual you will be able to properly install and operate the unit The Backup Camera System is intended to be installed as a supplement aid to your
6. W SAFETY Monitor Specifications TFT LCD Digital Monitor Screen Size Dot Resolution Display Format Display Brightness Viewing Angle Video Input Video Source Power Supply Power Consumption Operating Temperature Video System Overall Dimensions Weight Impact Rating Dot Pitch Sync System Reverse With Confidence 8008 x RGB x 480v 16 9 500 1 400cd m U 50 D 60 R 70 3 channel 1Vp p 75 DC 12V 24V 10 5W 30 C 80 C Auto NTSC PAL PLES 4006 5G 0 192H x 0 1805v Internal Camera Dimensions 3 25 MIC REAR VIEW SAFETY _ Camera Specifications Picture Elements Gamma Correction Image Sensor Lens View Angle Sync System Infrared distance Usable Illumination Power Source S N Ratio Electronic lris Video Output IR Switch Control Impact Rating Operating Temperature Storage Temperature Reverse With Confidence 1 4 Sharp Color CCD 250 000 pixels r 0 45 to 1 0 480TV lines PAL 500H x 582v NTSC 510H x 492v 2 1mm 130 Internal Synchronization 50 Feet 18 Infrared IR 0 Lux IR On DC 12V 24V 10 More than 48dB 1 50 160 1 100 000sec 1Vp p 75ohm ACDS Automatic Control 20G Vibration 100G Shock 30 C 60 C RH 95 Max 30 C 70 C RH 95 Max Troubleshooting Monitor Displays Blue Screen amp Displays No Signal Do a hard reset unplug all Verify that the blue positive cables and po
7. ealant around grommet to increase resistance to water penetration Connect camera to the camera extension cable which runs inside the vehicle The camera system can be wired to be powered ON the entire time the vehicle is on This is typical in RV and some com mercial applications The camera and monitor can always be activated by manually pushing the power button on monitor This is in addition to utilizing the positive triggers Note If connecting power directly to battery the camera is always ON and therefore can drain battery Therefore it is recommended to connect power to an ignition switched accessory power source REAR VIEW SAFETY jring Camera t Monitor e Audio works on two ports of multiplexer and positive triggers must be triggered for audio to operate These are port 3 labeled backup blue trigger and port 2 labeled DVD white trig ger When installing a TWO 2 camera setup use ports 3 and 2 and use positive triggers To automatically have camera and monitor turn ON when vehicle activates simply twist BLUE positive trigger 12V to Red Power line 12V and wire to ignition power which can be an accessory switch fuse line and black wire 12V to chassis ground Infrared technology built into camera IRs are activated automatically according to the lighting conditions Reverse With Confidence Blue and White There is a built in voltage regulator for
8. ess UP and DOWN buttons REAR VIEW SAFETY Splitting Splicing Installing sun shield Put shade cover on the display Installing back cover Put the monitor with shade cover in the back cover only for embedded monitor Splitting back cover Hold monitor with 2 hands and detach with fingers as indicated by arrows only for embedded monitor Splitting sun shield Take the monitor with the left hand and detach with right hand as indicated by the white arrow see below m m Re gt 1 2 Yellow Video 3 Green Mirror Normal Imaging 4 White Audio 5 Black Ground Reverse With Confidence va O au REAR VIEW SAFETY Multiplexer 000000 000000 2 e 3 _ Camera t ni normal mirror Pin Number 1 a Porti Description Blue Reverse Gear Power circuit port 3 Yellow Camera Port 1 Red DC12 24V power input White Camera Port 2 Black Ground or DVD Reverse With Confidence e Port 3 Backup Rotatio Imager 5 2 5 Power selection Camera Down UP Exit in E with sun shade 1 M On Of Button election ArroyArrow M ode power video select down up _ ANNA NNNM 11 ANA ANA w mirror normal image e I1 LCP REAR VIE
9. isclaimer Rear View Safety and or its affiliates does not guarantee or promise that the user of our systems will not be in part of an accident or otherwise not collide with an object and or person Our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law Our camera systems have a limited field of vision and do not provide a comprehensive view of the rear or side area of the vehicle Always make sure to look around your vehicle and use your mirrors to confirm rearward clearance and that your vehicle can maneuver safely Rear View Safety and or its affiliates shall have no responsi bility or liability for damage and or injury resulting from accidents occurring with vehicles having some of Rear View Safety products installed and Rear View Safety and or its affiliates the manufacturer distributor and seller shall not be liable for any injury loss or damage incidental or consequential arising out of the use or intended use of the product In no event shall Rear View Safety and or its affiliates have any liability for any losses whether direct or indirect in contract tort or otherwise incurred in connection with the systems including but not limited to damaged property personal injury and or loss of life Nei
10. our systems which can handle 12 24 volts Real consumption is 10 to 30 Volts When installing all THREE 3 cameras use all three ports and connect all positive triggers to appropriate connections When using the postive trigger functions blue yellow amp white wires each trigger function needs to work on a seperate 12V source i e the Yellow and White wires can be wired to a turn signal circuit etc Grid lines function can be turned on off by manually from menu See page 14 Installation Diagram Figure 1 1 Figure 1 2 Connection of U Connection of Bracket Flushmount Bracket 12 REAR VIEW SAFETY 5 a Installing the Monitor TOK 5 DOOR 66ft Extension Cable Monitor dE Dr Optional Camera Available DC12V 24V red Ground black Port 83 blue Port 2 white Port 1 yellow Reverse With Confidence Monitor Operation CAMERA DOWN SELECTION ARROW MENU SELECTION UP BUTTON ARROW POWER ROTATE ON OFF IMAGE Back Exit when in Menu Mode To turn on the monitor press POWER button To get to the menu press MENU and use arrows to choose your settings To adjust brightness press MENU Use arrows to choose desired camera and press MENU to select Once selected use arrows to set the brightness To adjust contrast press MENU Use arrows to choose desired camera and press MENU to select Once selected use arrows
11. ther shall Rear View Safety and or its affiliates have any responsibility for any decision action or inaction taken by any person in reliance on Rear View Safety systems or for any delays inaccuracies and or errors in connection with our systems functions REAR VIEW SAFETY Take Notes Reverse With Confidence SAFETY REVERSE WITH CONFIDENCE If you have any questions about this product contact Rear View Safety Inc 1797 Atlantic Avenue Brooklyn NY 11233 800 764 1028 BETTER CAMERAS BETTER SERVICE IT S OUR GUARANTEE
12. uses aircraft grade connectors which means the camera cable can be exposed to all weather elements Do not run the cable over sharp edges do not kink the cable and keep away from HOT and rotating parts Fasten all cables and secure all excess cable N Monitor 1 To Attach the Pedestal mount to the dashboard or to the head liner using self tapping screws and or the adhesive pad 2 Attach monitor to mount and adjust mounting angle to allow optimum driver viewing comfort see figure 1 1 on page 12 Reverse With Confidence 0 Wiring Camera Monitor When installing a ONE 1 camera setup connect camera extension cable from the rear view camera to port labeled backup most systems port 3 Connect red 12V wire to ignition power source and black wire 12V to chassis ground Do not use white and yellow wires The blue wire is the REVERSE trigger wire In typical rear view installations connecting this wire to the vehicle s backup light circuit will activate the rear view image whenever the vehicle shifts into reverse Before drilling be sure no cable or wire is on the other side Feed as much cable as possible into vehicle amp clamp securely This reduces the possibility of cable being hooked or snagged Camera Drill a 20mm 0 8in diameter hole into vehicle body near the camera and bracket Insert camera cable into vehicle be careful not to kink cable and fit grommet into hole Apply s
13. wer cables from trigger on power harness is multiplexer silver box leave put to power 12v out for 1 minute and then If the problem still persists ver re connect them ify that alternate ports work If e Check to ensure that the con alternate ports do not work re nection to the camera is tight move Blue Trigger wire from e Verify camera cable is plugged 12V and select alternate chan into port labeled Backup Camera nels Monitor Will Not Power Up no backlight on power button e Check fuse e Check ground connection e Check 12v to monitor No Image On Screen e Verify camera is on correct Connect known working camera input camera and cable to monitor Verify cable is connected to Verify Blue trigger is receiving monitor power Verify camera is connected to cable Audio on Camera e Verify chosen camera has audio Confirm that the Blue audio e Verify volume setting trigger is connected to 12v4 REAR VIEW SAFETY Warranty One Year Warranty Rear View Safety Inc warrants this product against material defects for a period of one year from date of purchase We reserve the right to repair or replace any such defective unit at our sole discretion Rear View Safety Inc is not responsible for a defect in the system as a result of misuse improper installation damage or mishandling of the electronic components Rear View Safety Inc is not responsible for consequential damages of any kind This warranty
14. y The Rear View Camera Sys tem is not intended for use during exstensive back up maneuvers or backing into cross traffic or pedestrian walkways Please always remember the area displayed by the Rear View Camera System is limited It does not display the entire panorama that is behind you Safety Information INSTALLATION Electric shock or product malfunction may occur if this product is installed incorrectly Use this product within the voltage range specified Failure to do so can cause electronic shock or product malfunction Take special care when cleaning the monitor Make sure to firmly affix the product before use If smoke or a burning smell is detected disconnect the system immediately Where the power cable may touch a metal case cover the cable with a friction tape A short circuit or disconnected wire may cause a fire While installing the Rear View System be careful with the wire positioning in order to avoid wire damage The Rear View System should only be used when the vehicle is in reverse Do not watch movies or operate the monitor while driving as it may cause an accident Do not install the monitor where it may obstruct drivers view or obstruct an air bag device Dropping the unit may cause possible mechanical failure REAR VIEW SAFETY Safety Information If you have questions about this product contact Customer Service Rear View Safety 179
Download Pdf Manuals
Related Search