FiberMix 2802-60FE
Contents
1. www godynamix com ZA FiberMix 2802 60FE BL User Manual Legal Notices Warranty Dynamix Pro Ltd makes no warranty of any kind with regard to this manual including but not limited to the implied warranties of merchantability and fitness for a particular purpose Dynamix Pro Ltd shall not be held liable for errors contained herein or direct indirect special incidental or consequential damages in connection with the furnishing performance or use of this material A copy of the specific warranty terms applicable to your Dynamix product and replacement parts can be obtained from Service Office Restricted Rights Legend All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Dynamix Pro Ltd The information contained in this document is subject to change without notice Copyright Notices Copyright 2007 Dynamix All rights reserved No part of this publication may be excerpted reproduced translated or utilized in any form or by any means electronic or mechanical including photocopying and microfilm without permission in Writing from Dynamix Pro Ltd Trademark Notices Dynamix is the trademark of Dynamix Pro Ltd Java is a U S trademark of Sun Microsystems Inc Microsoft is a U S registered trademark of Microsoft Corporation Windows NT is a U S registered trademark of Microsoft C2. s network management platform NView NNM V5 0 together with corresponding EMS FM002 5 0 Build 3 or above version users can view the status information of the FM2802 60FE BL device Users can also control and configure the device on the network management platform 6 2 Network management query The following information can be queried on the network management platform Local device version Local remote optical interface alarm Local remote device model Local remote device El alarm Local remote El loopback status Local remote Ethernet interface status The status of ALS function VV VVVVV 6 3 Network management configuration The function listed below can be configured on the network management platform gt Local remote El loopback settings gt Local remote Ethernet interface settings includes working mode and bandwidth contral gt ALS function settings 12 www godynamix com User Manual Chapter 7 Device Installation Preparation and Connection 7 1 Checking and preparation before installation gt VV V vv Please check the model and the number of the device and spare parts according to the packing list Please be sure that the appearance of the device is intact If there is any evidence that the device has been affected by damp please dry it before installation Please read this manual with caution before installing the device Please have all types of cables that are needed ready and make sure there are no sh
3. a protective ground Always connect the power cord first to the equipment and then to the wall socket If a power switch is provided in the equipment set it to the OFF position If the power cord cannot be readily disconnected in case of emergency make sure that a readily accessible circuit breaker or emergency switch is installed in the building installation Connection of DC Mains Unless otherwise specified in the manual the DC input to the equipment is floating in reference to the ground Any single pole can be externally grounded Due to the high current capability of DC mains systems care should be taken when connecting the DC supply to avoid short circuits and fire hazards DC units should be installed in a restricted access area 1 e an area where access is authorized only to qualified service and maintenance personnel Make sure that the DC supply is electrically isolated from any AC source and that the installation complies with the local codes Before connecting the DC supply wires ensure that power is removed from the DC circuit Locate the circuit breaker of the panel board that services the equipment and switch it to the OFF position When connecting the DC supply wires first connect the ground wire to the corresponding terminal then the positive pole and last the negative pole Switch the circuit breaker back to the ON position A readily accessible disconnect device that is suitably rated and approved should be incorporated in the b
4. alarm LOF alarm E 3 alarm and E 6 alarm occurs at the local optical interface Red Flickering remote optical interface total alarm no alarm occurs at the local optical interface while at least one of LOS alarm LOF alarm E 3 alarm and E 6 alarm occurs at the remote optical interface 5 www godynamix com User Manual Yellow ON both the local and remote device is working normally when the remote system 1s power down 3 3 Interface description 2 El balanced interface I RJ 45 interface provides 2 lines of 120Q balanced El signal El 1 pin 1 and 2 output pin 4 and 5 input El 2 pin 7 and 8 output pin 3 and 6 input D Note Please be sure that the pin arrangement of the connector of the cable is correct Please read the instructions for cable making with caution before making cable 6 www godynamix com User Manual Chapter 4 Device Settings 4 1 DIP switch description 4 1 1 The location of the DIP switches There are an 8 bit DIP switch SWI and a 4 bit DIP switch SW2 on the back of the print circuit board 4 1 2 DIP switch description DIP switch SW1 gt Bit 1 Ethernet interface auto negotiation When the Ethernet interface Auto Negotiation is enabled the Auto MDI MDIX function is enabled at the same time If the Ethernet interfaces of switch HUB or NIC are working on forced mode the Ethernet interface of FM2802 must be working in half duplex mode When the Auto Negotiation of the Ethernet interface is di
5. Device installation Please fix the chassis on to the rack and insert the device into the slot of the chassis Please fasten all Screws If network management will not be used please make sure that the DIP switches on the module have been set according to need before being fixed into the chassis 13 www godynamix com User Manual 7 2 2 Cable connection Please make sure that the El interfaces and the optical interface are well connected 7 2 3 Device electrifying Please fix the module properly in the chassis before turning ON the power supply After electrifying the power supply status indicator PWR on the front panel of the device will turn ON to show that the power supply is working normally 14 www godynamix com User Manual Appendix A FAQ For some problems you may meet during installation and operation please try to solve them following the suggestions below For the problems can not be solved using the following suggestions please contact with distributors for technical support gt Optical interface indicator ALM red ON Local optical interface Rx alarm Please check whether the fiber is well connected to the Rx of the optical interface and whether the Tx and Rx of the optical interface have been incorrectly connected Users can use optical power meter to measure the optical power of the receiving signal The optical power of the receiving signal should exceed the receiving sensibility of the optical interface a
6. aa R acaso ARR RR 1 1 3 Ordering information gt gt nnn nnn nnn nn nn nnn nnn nnn aaa w 1 Chapter 2 Technical Specifications n umuaumauuansamanaanaananaaaaame 3 2 1 Technical specifications of the El interface n nn nnn anna anna nana ana a mm m 3 2 2 Technical specifications of Ethernet interface nn 2 nnn nn nnn nnn nnn nnn ccna 3 2 3 The technical specifications of the optical interface gt 3 2 WES UDI ee O PI E 4 gt 9 Operating SAVIO Nm O iris A ee a RA AAA 4 2 1 Storing environment asmak na a III gt gt 4 2 9 OUTINGS MA UU AO geaae 4 Chapter 3 Device Appearance and Descripiton n msumsuasuaem 5 3 DEVICETTONUPDANel gt gt A AA AAA 9 3 2 Indicator description FA GRA AAAA RO 9 9 onten ace ESCAPA A 6 Chapter 4 Device Settings 7 A Ue SWIC VCS SCIP FRZ a eee es BL The location Ote DIP SWIICNES gt RF A RS ERES 1 412 DIF Swich GESCHIDUON ZG SST R A a A AREA 7 ml AS MING se cs gaa eae A eee ee 10 Chapter 5 Typical Application s s s s s ssssss szs s 11 Oi BASIC CONNECCION a eee ae e e 11 Chapter6 Network Management Features 12 5 1 INGIWOIK management platon ROR EA RAA RA AR REAR ARA 12 8 2 NEIW TK managementiquer lt ai ROR AA RR RAR RAR 12 6 3 Network managemen
7. dular PDH multiplexer of a fiber optic transmission device applicable to point to point network or network with small or medium capacity like wireless communication base station private networks switch network and etc FM2802 60FE BL PDH multiplexer realizes the transmission of at most 2 lines of El service and 1 line of 10 100M Ethernet service It operates in chassis developed by Raisecom and is generally applied to central site networking The device is SNMP manageable 1 2 Function features Dual El and single pure 100Mbps wire speed Fast Ethernet transmission capability Remote device power off detection and alarm notification In support of ALS function Ethernet port bandwidth control 1 10 100Mbps Ethernet interface supports Auto negotiation Auto MDI MDIX function Ethernet interface rate and duplex mode selectable The maximal Ethernet data frame length in support is 1784 bytes For Ethernet interface working in full duplex mode IEEE802 3x flow control is supported For Ethernet interface working in half duplex mode back pressure flow control is supported Indication for both local and remote site alarms Local and remote El loopback testing function makes fault removal easier Local and remote SNMP manageable Adopt grand scale ASIC chip Low power consumption 4 layer circuit board design guarantees high reliability VVVVVVV V VV NY 1 3 Ordering information Device Description FM2802 60FE BL S 1 Modular device 2 12062 bala
8. e in Force Remote mode no matter whether network management software is used otherwise abnormity will occur during the operation of the device DIP switch SW2 The DIP switch SW2 identifies the optical transceiver type adopted by the device The settings of SW2 are completed by the manufacturer Please keep the factory settings of SW2 They are not allowed to be changed SW2 1 SW2 2 SW2 3 SW2 4 Optical transceiver Type 9 www godynamix com User Manual ON OFF OFF S3 1550 Tx amp Rx ON OFF 513 1310 Tx 1550 Rx ON OFF OFF SS15 1550 Tx 1310 Rx ON OFF OFF SS23 1310 Tx 1550 Rx ON OFF OFF OFF SS25 1550 Tx 1310 Rx 4 1 3 Default Settings The default settings of all bits of SW1 are OFF 10 www godynamix com User Manual Chapter 5 Typical Application 5 1 Basic connection pa 234567 89101112 CONSOLE cr ea WF WF HS1 HS2 OK1 OK2 PS A O STA LOS O Ay El Device CO Site 18 3309 2082SINO8 Client Site JJ O 09 N 00 no D a z p w w Device As is shown in the figure above FM2802 60FE BL can be applied in pair and network management can be realized on the application In addition FMS2802 60FE BL can also be inter connected with FM2802 30FE BL FM832 30 60 FM832 30 60 BL FM831 60 FV35 and etc 11 www godynamix com User Manual Chapter 6 Network Management Features 6 1 Network management platform Through Raisecom
9. ity lt 90 25 C 2 7 Storing environment gt Storing temperature 40 80 C gt Storing humidity 5 90 no condensation 2 8 Outline and structure gt Physical outline modular device gt Dimension 91mm Height x 25mm Width x 172mm Depth gt Net Weight 0 13Kg 4 www godynamix com User Manual Chapter 3 Device Appearance and Descripiton 3 1 Device front panel Z O Y N N eh W 3 2 Indicator description Power supply indicator gt PWR Green power supply working status indicator ON the power supply is working normally E1 indicator gt LOSI Red indicator for loss of El signal at El 1 gt LOS2 Red indicator for loss of El signal at El 2 ON local loss of El signal alarm Flickering remote loss of El signal alarm but no local loss of El signal alarm OFF no loss of El signal alarm Ethernet indicator gt LNK ACT Green Ethernet interface indicator ON the Ethernet cable 1s correctly connected Flickering the Ethernet cable is well connected and there is data transmitting or receiving OFF the Ethernet cable is not well connected gt 100M Green Ethernet interface rate indicator ON the Ethernet interface is working at the rate of 100Mbps OFF the Ethernet interface is working at the rate of 10Mbps Optical interface indicator gt ALM LPR two color optical interface alarm indicator Red ON local optical interface total alarm at lease one of LOS
10. ivers shall be connected with optical fiber wires or shield with optical transceiver cover for fear that laser light harms to operator s eyes Handling Energized Products General Safety Practices Do not touch or tamper with the power supply when the power cord is connected Line voltages may be present inside certain products even when the power switch if installed is in the OFF position or a fuse is blown For DC powered products although the voltages levels are usually not hazardous energy hazards may still exist Before working on equipment connected to power lines or telecommunication lines remove jewelry or any other metallic object that may come into contact with energized parts Unless otherwise specified all products are intended to be grounded during normal use Grounding is provided by connecting the mains plug to a wall socket with a protective earth terminal If an earth lug is provided on the product it should be connected to the protective earth at all times by a wire with a diameter of 18 AWG or wider Rack mounted equipment should be mounted only in earthed racks and cabinets Always make the ground connection first and disconnect it last Do not connect telecommunication cables to ungrounded equipment Make sure that all other cables are disconnected before disconnecting the ground Connection of AC Mains Make sure that the electrical installation complies with local codes Always connect the AC plug to a wall socket with
11. nced El interfaces RJ 45 I Ethernet interface RJ 45 1 optical interface DSC dual strand single mode transmission distance 0 25km FM2802 60FE BL S2 Modular device 2 12002 balanced El interfaces RJ 45 I Ethernet interface RJ 45 1 optical interface DSC dual strand single mode transmission distance 10 60km FM2802 60FE BL S3 Modular device 2 12002 balanced El interfaces RJ 45 I Ethernet interface RJ 45 1 optical interface DSC dual strand single mode transmission distance 15 120km 1 www godynamix com User Manual FM2802 60FE BL SS13 Modular device 2 12002 balanced El interfaces RJ 45 Ethernet interface RJ 45 1 optical interface SC PC single strand two wavelength Tx wavelength 1310nm transmission distance 0 25km FM2802 60FE BL SS15 Modular device 2 12062 balanced El interfaces RJ 45 Ethernet interface RJ 45 1 optical interface SC PC single strand two wavelength Tx wavelength 1550nm transmission distance 0 25km FM2802 60FE BL SS23 Modular device 2 12062 balanced El interfaces RJ 45 Ethernet interface RJ 45 1 optical interface SC PC single strand two wavelength Tx wavelength 1310nm transmission distance 10 50km FM2802 60FE BL SS25 Modular device 2 12002 balanced El interfaces RJ 45 Ethernet interface RJ 45 1 optical interface SC PC single strand two wavelength Tx wavelength 1550nm transmission distance 10 50km Note Among FM280X se
12. nd it should not be around the critical value of the receiving sensibility gt Optical interface indicator ALM red flickering Remote optical interface Rx alarm Please check whether the fiber is well connected to the Rx of the remote optical interface and whether the Tx and Rx of the remote optical interface have been incorrectly connected Users can use optical power meter to measure the receiving optical power of the remote optical interface The optical power of the receiving signal should exceed the receiving sensibility of the remote optical interface and it should not be around the critical value of the receiving sensibility gt Ethernet interface indicator LINK wouldn t turn ON Firstly please check whether the cable is broken down Secondly please check whether the network device connected to the Ethernet interface is working properly Thirdly please make sure that the pin arrangement of the cable applied is correct gt The El interface LOS red indicator turns ON El loss of receiving signal alarm No HDB3 coded signal input Please check whether the El interface is well connected and whether the pin arrangement of the connector of the 1200 El cable is correct 15 Web http www godynamix com Email support dynamix ua
13. orporation Windows 2000 is a U S registered trademark of Microsoft Corporation Windows XP is a U S registered trademark of Microsoft Corporation Windows and MS Windows are U S registered trademarks of Microsoft Corporation Contact Information World Wide Web You can access the most current Dynamix product information on the World Wide Web at the following URL http www godynamix com http www dynamix ua Feedback Comments and questions about how the FM2802 60FE BL device works are welcomed Please review the FAQ in the related manual and if your question is not covered send email by using the following web page http www godynamix com ukr cont htm If you have comments on the device specification instead of the web page above please send comments to sales O godynamix com sales Qdynamix ua We hope to hear from you CONTENTS Release Notes ena 9 General Safety Instructions s us susssusssssssnsasansss m 6 salei O VIMOS EG ai GR a A eae R ie 6 Handling Energized Products nnn am am aa aaa 6 General Salely FAC ICES ccemcasseasas casa eRe A AS 6 CONMECTOMORAG MainSza c Gi Ra RAR ARR RAR RR ARR 1 A DC Mans ss ssa R R E ARR RA 1 Preventing Electrostatic Discharge Damage nn nnn nnn a am m 1 Chapter 1 Product Overview ns 1 LE O nO nl dd a oe 1 ie FUNCION TO A UE A P
14. ort circuits and open circuits Please make sure that the power supply of the chassis is in the operating voltage range please have the rack of the chassis device well earthed Please prepare BER tester optical power meter for line quality testing Please fix the chassis on to a 19 inch rack or place it on a balanced stable and safe place please be sure the environment meets the requirements of the device 7 1 1 Make sure that the E1 cable applied meet the requirement of the device For El cable users can choose 22AWG or 24AWG twisted pair The El interfaces of FM2802 60FE BL are 120Q balanced El interfaces Please check the type pin definition and impedance of the El interface of the device on the opposite site of the communication before connection Please check the user manuals for devices that communicate with FM2802 60FE BL via El for information 7 1 2 Make sure that the fiber applied matches the requirement of the device For FM2802 60FE BL M please use multi mode fiber with DSC connector For FM2802 60FE BL S1 S2 S3 please use single mode fiber with DSC connector For FM2802 60FE BL SS15 SS25 please use single mode fiber with SC PC connector 7 1 3 Confirm the fiber cable type applied The cable type for the interface of multi mode fiber 62 5 125um multi mode fiber or 50 125um multi mode fiber The cable type for the interface of single mode fiber 9 125um single mode fiber 7 2 Installation procedures 7 2 1
15. rectional loopback Remote bidirectional loopback The following two figures show the loopback point of the remote bidirectional loopback and local bidirectional loopback respectively Optical BER E1 Side Interface E1 Side Tester 1 Side Local Remote Set remote bidirectional loopback on the local PDH multiplexer 8 W ww godynamix com User Manual E Optical E1 Side Interface E1 Side Side BER Tester Local Remote Set local bidirectional loopback on the local PDH multiplexer D Note Please note that when configuring any loopback on the local PDH multiplexer the status of all loopback setting bits of the DIP switch on the remote PDH multiplexer must be OFF no loopback gt Bit 8 Remote network management control Network management control When using the device in pair if the device at the client side is in a FMOOI 1 single slot chassis the device in auto recognition mode will switch to the force remote mode automatically If the device at the client side is in a FM002 16 16 slot chassis the users have to set the network management mode of the device to force remote mode manually For the device at the central site if local management is required please set the network management mode of the device to auto recognition mode D Note Please note that when using the device in pair and both of the devices are in FM002 16 chassis one of the devices must b
16. ries devices with optical transceivers for dual strand fiber the devices with Same optical transceivers can inter connect with each other For example FM2802 60FE BL S1 can be inter connected with FM2801 60FE FV35 S1 FM2802 30FE BL SI and other FM2801 series devices with S1 optical transceivers Among FM2802 series devices adopting optical transceivers for single strand fiber device with SS13 can communicate with device with SS15 while device with SS23 can communicate with device with SS25 For example FM2802 60FE BL SS13 can be inter connected with FM2801 60FE FV35 SS15 FM2801 30FE FV35 SS15 and other FM2801 series devices with SS15 optical transceivers 2 www godynamix com User Manual Chapter 2 Technical Specifications 2 1 Technical specifications of the E1 interface VVVVVV WV Bit Rate 2048Kbps 50ppm Coding HDB3 Interface Type RJ 45 Interface Impedance 120Q Physical characteristic comply with ITU T 6 703 recommendations Transfer characteristic comply with ITU T G 823 recommendations Jitter tolerance comply with ITU T G 823 recommendations 2 2 Technical specifications of Ethernet interface gt gt gt gt Yy Interface type RJ 45 Standard compliance IEEE802 3 IEEE802 3u Working mode 10 100Mbps full duplex half duplex selectable Auto negotiation forced mode selectable Flow control For Ethernet interface working in full duplex mode IEEE802 3x flow control is supported For Ethernet interface wo
17. rking in half duplex mode back pressure flow control is supported Auto MDI MDIX function in support of Auto MDI MDIX this function will become ineffective if the Auto negotiation function of the interface is disabled Other features in support of IEEE802 1d Spanning Tree and IEEE802 1q VLAN packet transparent transmission Maximal data frame in support Ethernet data frame of 1784 bytes 2 3 The technical specifications of the optical interface VVVV Bit rate 150Mbps Line coding scrambled NRZ Interface type SC interface Optical transmission parameter different optical transceivers have different optical interface parameters please see the table below Optical Interface LASER Receiver Wavelength TX Overload Receiving Transmission Optical Sensibility Distance Km Power dBm dBm transceive Type DSC PC PIN 1310 so gt 8 es DSCPC DFB PIN 1550 DFB gt 40 lt 36 ss13 SCIPC PIN TX 1310 gt 8 lt 30 www godynamix com User Manual SS15 SC PC FP DFB TX 1550 RX 1310 SS23 SC PC TX 1310 RX 1550 SS25 SC PC DFB PIN TX 1550 RX 1310 Note The transmission distance in the table indicates the maximal transmission distance in typical optical fiber condition The transmission distance that can be realized depends on the factual status of the network 2 4 Power supply Power consumption lt 3W 2 5 Operating environment gt Operating temperature 0 60 C gt Operating humid
18. sabled forced mode the Auto MDI MDIX will be disabled too and the Ethernet interface will be working in MDIX mode And the working mode depends on the settings of Bit 2 and Bit 3 Bit 1 Ethernet interface Auto Negotiation Enable ON Disable gt Bit 2 Ethernet interface 10 100Mbps setting The setting of this bit is ineffective when the status of Bit 1 is OFF If the status of Bit 1 is ON the setting of the Bit 2 determines the bit rate of the Ethernet interface Bit 2 Ethernet interface 10 100Mbps setting 100Mbps ON 10Mbps gt Bit 3 Ethernet interface duplex mode setting The setting of this bit is ineffective when Bit 1 is OFF When the status of Bit 1 is ON the setting of Bit 3 decides the duplex mode of the Ethernet interface Bit 3 Ethernet interface duplex mode setting ON half duplex full duplex gt Bit 4 ALS function setting 7 www godynamix com User Manual Bit 4 ALS function setting OFF Disable ON Enable gt Bit 5 Loopback setting of 1 El Bit 5 Loopback setting of 1 El OFF No loopback ON Loopback gt Bit 6 Loopback setting of 2 El Bit 6 Loopback setting of 2 E1 OFF No loopback ON Loopback gt Bit 7 Loopback type setting Users can set the loopback of El to remote bidirectional loopback or local bidirectional loopback when the loopback of the El is enabled Bit 7 Loopback type selection ON Local bidi
19. t configurator e se n RAA ARR R ARR RCR 12 Chapter 7 Device Installation Preparation and Connection 13 7 1 Checking and preparation before installation 13 7 1 1 Make sure that the E1 cable applied meet the requirement of the device 13 7 1 2 Make sure that the fiber applied matches the requirement of the device 13 TAS Continm the Tiber Cable type applied lt e gt gt gt gt RA PR RA KR AR ARE 13 2 nStalalio Br cedUreSS gt o FR RR a ee ea SR ree Sree 13 7 2 Device Mstalla On s santi sects es a caio dane tae neta eased an o rien ideias ent 13 1 22 Cable CONNECCION rerne cascatas cosas ne 14 O Iodo O ia o o ic 14 Appendix A FAQ wawa ana a A A A AAA AAAA AAAA 15 Release Notes 20071119 200706 REV A General Safety Instructions The following instructions serve as a general guide for the safe installation and operation of telecommunications products Additional instructions if applicable are included inside the manual Safety Symbols A Warning A Warmng This symbol may appear on the equipment or in the text It indicates potential safety hazards regarding product operation or maintenance to operator or service personnel product is energized or connected to outdoor telecommunication lines Pro
20. tective earth the marked lug or terminal should be connected to the building protective earth bus Danger of electric shock Avoid any contact with the marked surface while the Some products may be equipped with a laser diode In such cases a label with the laser class and other warnings as applicable will be attached near the optical transmitter The laser warning symbol may be also attached Please observe the following precautions e Before turning on the chassis with optic module make sure that the fiber optic cable is intact and is connected to the transmitter e Do not attempt to adjust the laser drive current e Do not use broken or unterminated fiber optic cables connectors or look straight at the laser beam e The use of optical devices with the equipment will increase eye hazard e Use of controls adjustments or performing procedures other than those specified herein may result in hazardous radiation exposure ATTENTION The laser beam may be invisible Always observe standard safety precautions during installation operation and maintenance of this product Only qualified and authorized service personnel should carry out adjustment maintenance or repairs to this product No installation adjustment maintenance or repairs should be performed by either the operator or the user All extension slots are not hot swappable Before operating modules in the electricity conditions please be noticed that optical transce
21. uilding installation Preventing Electrostatic Discharge Damage Modules which can be plugged into chassis are sensitive to damage from static electricity Conversely static voltages as high as 35 000V can be generated just by handling plastic or foam packing material or by sliding assemblies across plastic and carpets Not exercising the proper electrostatic discharge ESD precautions can result in intermittent or complete component failures To minimize the potential for ESD damage observe the following guidelines e Always use an ESD preventive antistatic wrist strap or ankle strap and ensure that it makes good skin contact e When removing or installing a component make sure the equipment end of your antistatic strap leash is connected to the ESD connection sockets on the front of the chassis or to a bare metal surface on the chassis Avoid contact between the component and your clothing The wrist strap only protects the component from ESD voltages on the body ESD voltages on your clothing can still cause component damage e Always place a card component side up on an antistatic surface in an antistatic card rack or in a static shielding bag If you are returning the item to the factory immediately place it in a static shielding bag e Handle Modules by the metal card carrier edges only Avoid touching the board or any connector pins www godynamix com User Manual Chapter 1 Product Overview 1 1 Overview FM2802 60FE BL is a mo
Download Pdf Manuals
Related Search