User Manual - GC-SAT
Contents
1. Contact SIEI Description 1 EXT_ON_OFF External connection for On Off key input to LBT 2 OV Signal ground OV signal reference and return 3 EXT_11HZ 90ms frame sync signal used in testing 4 MIC_AUD Microphone audio input to LBT 5 EXT_GND Power Ground input to LBT 6 EXT PWR Power input to LBT 7 EXT PWR Power input to LBT 8 EXT_GND Power Ground input to LBT 9 SPKR_AUD Speaker audio output from LBT 10 DPL_TX Digital Peripheral Link UART data output from LBT 11 DA_TX PCM digital audio output from LBT 12 DF_DTR Data Fax Data Terminal Ready input to LBT 13 DF_RI Data Fax Ring Indication output from LBT 14 DPL_RX Digital Peripheral Link UART data input to LBT 15 DF_RTS Data Fax Request to Send input to LBT 16 DF_DSR Data Fax Data Set Ready output from LBT 17 DF_S_TX Data Fax UART data input to LBT 18 DF_CTS Data Fax Clear to Send output from LBT 19 DF_DCD Data Fax Data Carrier Detect output from LBT 20 OV Signal ground OV signal reference and return 21 DA_FS PCM digital audio frame sync output from LBT 22 DA_RX PCM digital audio input to LBT 23 DA_CLK PCM digital 2 048MHz audio clock output from LBT 24 OV Signal ground OV signal reference and return 25 DF_S_RX Data Fax data UART output from LBT 26 NETWORK_ AVAILABLE Network available output from LBT Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 Table 4 25 way D co2. Table 10 Link Margin Configuration Cable Loss Link Margin 9522B LBT with accessory antennas Note 1 2 dB Note 2 13 1 dB Note 3 Note 1 Other antenna options are available Note 2 Cable losses should be minimized Note 3 Link Margin given for free space 14 Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 5 0 Instructions for the safe Installation and use of the 9522B LBT The 9522B LBT is intended for integration into a finished product The integrator of the 9522B LBT is required to connect a power supply antenna and user interface to the 9522B LBT To ensure that the 9522B LBT is correctly installed the following general instructions sub section 5 1 are provided for the installer The integrator will be required to supply the end user of the integrated product incorporating the 9522B LBT with operating instructions and any other information relating to the maintenance and safety of the equipment sub section 5 2 5 1 Instructions for the Integrator e The 9522B LBT must be installed by an appropriately qualified installer and mounted securely as described in section 3 4 of this document e The power supply used to power the 9522B LBT must be checked to ensure it meets the requirements of sub section 4 1 2 of this document e Electrical connections to the 9522B LBT multi interface connector shall be as designated in Table 3 of sub section 3 3 10f this document e The
3. 6 32 thread type is desired a Textron Camcar Taptite Il Thread Rolling Fastener with a 15IP Torx Plus pan head is available in lengths of 1 4 5 16 3 8 1 2 5 8 3 4 and 1 inch as part number 3BE P814 00 3BE P8123 00 3BE P815 00 3BE P816 00 3BE P8124 00 3BE P817 00 and 3BE P818 00 respectively A 10IP Torx Plus flat head version is also available in a single length of 1 2 inch as part number 3BE P801 00 Another 6 32 thread type option is to insert a helical coil insert with a 6 32 internal thread into these features thus accommodating 6 32 threaded fasteners as mounting hardware for the 9522B LBT National Aerospace Standard NASM122238 serves as a technical reference for the recommended helical coil insert 3 5 Mounting in Harsh Environments If the 9522B LBT is to be used in a harsh environment with exposure to high humidity water or dust the LBT must be installed in the correct orientation with all connectors facing downwards 11 Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 4 0 Electrical Interfaces The subsections to follow contain interface information for the electrical interfaces of the 9522B LBT 4 1 DC Power Interface 4 1 1 DC Power Interface Signal Descriptions The DC power interface is comprised of the DC power inputs and a control signal as summarized in Table 5 below The EXT_PWR and GND inputs are used to supply DC power to the 9522B LBT The EXT_ON_OFF contro
4. Connector The 9522B LBT provides a single 50 O SMA type antenna connector both transmit and receive An adaptor is available to convert this connector to TNC to enable the 9522B to be used as a replacement for a 9522A 3 3 3 GPS Feed thru Connector To enable a GPS receiver to share the antenna the 9522B LBT passes the received signal through to a 50 Q SMA type connector It is intended that this be connected to a GPS receiver Note that this signal will not be usable during a call 3 3 4 SIM Chip Reader An integrated SIM chip reader is provided on the 9522B LBT This connector allows installation of the chip form of the SIM beneath a cover plate on the 9522B LBT housing 3 4 Mounting The 9522B LBT incorporates 6 mounting holes on its bottom surface that can aid in its mounting See Figure 3 for locations of these features It is recommended that a thread forming screw be used to mount the 9522B LBT via these features Particularly a Textron Camcar Taptite Il Thread Rolling Fastener of M3 5x0 6 thread type is recommended This fastener has a 15IP Torx Plus pan head and is available in lengths of 6 8 12 16 and 20 mm as part number 3BE P802 00 3BE P803 00 3BE P8185 00 3BE 10 Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 P804 00 3BEP8186 00 and 3BE P8187 00 respectively Length should be chosen to ensure that penetration into the 9522B LBT housing does not exceed 11 mm If a
5. available after appropriate Non Disclosure and or License Agreements are executed 12 Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 4 3 RS232 Data Interface 4 3 1 RS232 Data Signal Descriptions The RS232 data interface is comprised of eight standard RS232 data control and status signals plus a ground level signal reference This interface allows a connected Data Terminal Equipment DTE to utilize the 9522B LBT s modem functionality via AT command control A 3 wire RS232 Data minimal interface may also be implemented however the 9 wire interface offers better control and is the recommended implementation 4 3 2 Autobaud Autobaud is enabled by default Autobaud will occur on the following characters a A or CR carriage return Autobaud will also occur on the escape sequence character provided this is an odd number character Normally this is set to in register S2 See the AT Command Reference for details 4 4 Analog Audio Interface 4 4 1 Analog Audio Interface Signal Descriptions The analog audio interface is comprised of the analog audio input and output signals referenced to the OV signal ground as summarized in Table 6 below Table 6 Analog Audio Interface Signal Descriptions Signal Name Signal Description MIC AUD pin 4 Analog audio input to LBT SPKR AUD pin 9 Analog audio output from LBT OV pins 2 20 24 Signal ground 4 5 SI
6. current and voltage rating of the multi interface connector cable shall meet the requirements of the LBT DC power input e The electrical characteristics of the multi interface connector cable shall not degrade the 9522B LBT digital communications and analog audio signals e The multi interface connector cable will provide adequate screening from external electromagnetic interference e The 9522B LBT shall not be located in close proximity to sources of extreme temperature which will cause it to be operated outside of its temperature specification e The 9522B LBT shall not be operated without an appropriate antenna connected to its Antenna connector via a suitable 50 Ohm coaxial cable This antenna shall be sited at least 20cm away from any person 5 2 Instructions from the integrator to the user To comply with the requirements of sub clause 1 7 2 Safety instructions of the European Information technology equipment safety standard EN60950 1 2002 the integrator must ensure that Sufficient information shall be provided to the USER concerning any condition necessary to ensure that when used as prescribed by the manufacturer the equipment is unlikely to present a hazard within the meaning of this standard If it is necessary to take special precautions to avoid the introduction of hazards when operating installing servicing transporting or storing equipment the necessary instructions shall be made available As part of these instruc
7. 2405 3 0 Physical Specifications The 9522B is depicted in Figure 1 below Figure 1 Top View of 9522B 3 4 Environmental The environmental specifications of the 9522B LBT are summarized in Table 1 below Table 1 Environmental Specifications Parameter Value Operating Temperature Range 30 C to 70 C Operating Humidity Range 25 to 75 RH Storage Temperature Range 40 C to 85 C Storage Humidity Range lt 93 RH 3 2 Dimensions The overall dimensions of the 9522B LBT and its weight are summarized in Table 2 below Dimensioned views of the 9522B LBT are shown in Figures 2 5 which follow All dimensions are in mm unless otherwise stated Table 2 Mechanical Dimensions Parameter Value Length 160 mm 6 30 Width 78 mm 3 07 Depth 29 mm 1 10 Weight approximate 420g Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 20 00 La Figure 2 Bottom connector View D I o Oo o i E Y Y Oo Oo Y 21 70 x2 A 55 00 zi 60 50 I Figure 3 Back mounting View Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 Figure 4 F
8. B L Band Transceiver LBT is designed to be integrated into a specific application with other hardware and software to produce a solution designed for a specific application or vertical market Some examples of these solutions include a maritime voice telephony terminal or a vehicle tracking solution The LBT functionally supports all of Iridium s voice and data services Applications can be built to use one or multiple services using the voice and data interfaces The 9522B is a functional replacement to the 9522A LBT although the mechanical design and the electrical connectors differ Connection adaptors are available to enable the 9522B to be used in place of the 9522A A pass thru connector is provided to allow a GPS receiver to share the same antenna as the 9522B LBT The 9522B is regulatory approved for FCC Canada and CE assuming an antenna with a gain of 3dBi This allows the LBT to be integrated into a variety of subscriber products or retrofitted into existing LBT based products These products when integrated together will require regulatory testing to be conducted by the integrator The LBT is essentially provided as a black box with all interfaces provided via a 26 way 0 1 pitch connector The product provides the core transceiver module and SIM card reader All other functions and hardware such as keypad display power supply antenna etc must be provided by the solution developer The connector provides the following int
9. IRIDIUM 9522B L Band Transceiver Product Information Guide Revision 0 2 Iridium Satellite LLC Y 6701 Democracy Blvd Suite 500 yc globa ICom Bethesda MD 20817 USA A WWW iridium com Unit 11 33 Riley Road Woodmead 27 11 612 3660 sales gc sat com www gc sat com Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide Contents Revision History PP 2 1 0 gen EE 4 207 Standards ege 4 2 1 PCG C ompliatte sad eon i eec eedem e b d oes 4 22 NE MOEA OMPLIANCE Rte 4 3 0 Physical Specifications esee Ed ee URS RE EAE EEA CER ES 6 3 1 EE 6 3 2 Dimensio S tee eer 6 33 Interface ConneCtorsS iec t 8 3 3 1 Mt Hertert scie ee geet Ee eet 8 3 3 2 Antenna CONNEC LOE he EE EE 10 3 3 3 GPS Feed thru Connectors s cac vrbs e a seta EE T E 10 3 3 4 SIM Chip Reader EE 10 o MEM dictat M 10 3 5 Mounting in Harsh Environmentts scccsssscssssssssssssessncessancscsasesssacesenasesssecesenaesesss 11 4 0 See 12 4 1 DC Power Interface vei ode qe e EIER TUE In ER QUIA TUO Hd ege eh Edi 12 4 1 DC Power Interface Signal Descriptions eeeseseeeeeeeneeeneenen 12 4 1 2 DC Power Input Gap 12 4 2 Control Digital Audio DPL bus Interface 12 4 2 1 Control Digital Audio Interface Signal Descriptions sese 12 4 3 RS232 Data Interface even eerie Reese ES lesdaaes suneds CRURA S
10. M Interface An integrated SIM chip reader is provided on the 9522B LBT An external SIM card reader may also be interfaced as a peripheral to the 9522B LBT via the DPL bus control audio interface A SIM card in the external reader will take precedence over the SIM chip in the integrated connector when both are present 13 Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 4 6 RF Interface 4 6 1 RF Interface Specifications The RF interface requirements for the 9522B LBT are summarized in Table 7 below Table 7 General RF Parameters Parameter Value Frequency Range 1616 MHz to 1626 5 MHz Duplexing Method TDD Time Domain Duplex Oscillator Stability 1 5 ppm Input Output Impedance 500 Multiplexing Method TDMA FDMA 4 6 2 GPS Feed Thru Specifications The RF interface of the GPS feed thru connector are summarized in below Table 8 General RF Parameters Parameter Value Frequency Range 1575 MHz Input Output Impedance 500 Insertion Loss s3dB Noise Figure lt 7dB 4 6 3 Radio Characteristics The tables within this section contain radio characteristics of the 9522B LBT Table 9 In Band Characteristics Parameter Value Average Power during a transmit slot max 7 W Average Power during a frame typical 0 6 W Receiver Sensitivity at 50Q typical 118 5 dBm Receiver Spurious Rejection at offsets gt 1 MHz typical 60 dB
11. UR ORR S Edge Eet 13 4 3 1 RS232 NEEN ERR 13 4 3 2 ZA UTO DU EE 13 44 Analog Audio Interface tees VH y ee VAI Eed EEe ER EE 13 4 4 1 Analog Audio Interface Signal Descriptions 0 eeeeeeeeeceeeeeeeceeeeeeeteeeenteeeenaeees 13 4 5 eil Ree 13 4 6 eA A Boie E Ke ee 14 4 6 1 RF IMterlace Specifications Aender 14 4 6 2 GPS Fecd Thru pe n Ro M NE 14 4 6 3 Kabel EE ee EE 14 5 0 Instructions for the safe Installation and use of the 9522B LBT 15 5 1 Instructions for the IntegratOr esie soit tete case coaasasomacevaredentanncoass 15 5 2 Instructions from the integrator to the Wset enter pee iet ed e 15 6 0 Modem Commands and Configuration esee 15 Revision History Revision Date Comment V0 1 First revision based on 9522A product information guide V0 2 17 April 2008 Updated mechanical drawings mass and power Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 Export Compliance Information This product is controlled by the export laws and regulations of the United States of America The U S Government may restrict the export or re export of this product to certain individuals and or destinations For further information contact the U S Department of Commerce Bureau of Industry and Security or visit www bis doc gov Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 1 0 Product Overview The 9522
12. erfaces and connections Analog Audio Control Digital Audio RS232 Power Input On Off 2 0 Standards Compliance The 9522B is designed to comply with the standards for Radio Emissions Compliance Electromagnetic Compatibility and AC Safety in the United States European Union and Canada 2 1 FCC Compliance The 9522B is certified under 47 CFR Part 25 as FCC ID Q639522B It also complies with Part 15 of the FCC Regulations Operation is subject to the condition that this device does not cause harmful interference Any changes or modifications including the use of a non standard antenna not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment IMPORTANT To comply with FCC RF exposure requirements a minimum separation of 20 cm is required between the antenna and all persons 2 2 CE Compliance This product when marked with the CE symbol complies with the European Community Council Directive for R amp TTE 99 5 EC provided that the integrator user adheres to the instructions detailed in this LBT Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 Interface Specification This product is in compliance with applicable ETSI standards Compliance with the requirements of ETSI EN 301 489 requires the use of a shielded digital data interface cable Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 03
13. l input is pulled to a GND level to toggle the 9522B LBT on and off Note that both pairs of pins should be connected for EXT PWR and EXT GND Table 5 Control Audio Interface Signal Descriptions Signal Name Signal Description EXT_PWR pin 6 and 7 External power input EXT_GND pin 5 and 8 External power GND input EXT_ON_OFF pin 1 Power on off control input 4 1 2 DC Power Input Specifications The DC power requirements for the 9522B LBT are summarized in Table 5 below Note that these requirements apply to DC power measured at the 9522B LBT multi interface connector input Table 5 DC Power Input Specifications Parameter Value Main Input Voltage Range 4 0 VDC to 32 VDC Main Input Voltage Nominal 5VDC 12VDC or 24VDC Main Input Voltage Ripple 40 mV peak to peak Input Standby Power average 1 3W Max current during call 2 5A Typical current during call see note 1 4A Power Average Voice Data Call see note 7W Note The average power consumption depends on the view of the satellite constellation from the antenna 4 2 Control Digital Audio DPL bus Interface 4 2 1 Control Digital Audio Interface Signal Descriptions The control digital audio interface enables peripherals such as handsets and SIM card readers to be interfaced to the 9522B LBT The interface utilizes an Iridium Proprietary communication bus not detailed in this fact sheet Details can be made
14. nnector pin out Contact Signal Description 1 EXT_ON_OFF External connection for On Off key input to LBT 2 EXT_11HZ 90ms frame sync signal used in testing 3 EXT_GND Power Ground input to LBT 4 EXT PWR Power input to LBT 5 SPKR_AUD Speaker audio output from LBT 6 DA_TX PCM digital audio output from LBT 7 DF RI Data Fax Ring Indication output from LBT 8 DF RTS Data Fax Request to Send input to LBT 9 DF S TX Data Fax UART data input to LBT 10 DF DCD Data Fax Data Carrier Detect output from LBT 11 DA FS PCM digital audio frame sync output from LBT 12 DA CLK PCM digital 2 048MHz audio clock output from LBT 13 DF S RX Data Fax data UART output from LBT 14 OV Signal ground OV signal reference and return 15 MIC_AUD Microphone audio input to LBT 16 EXT PWR Power input to LBT 17 EXT_GND Power Ground input to LBT 18 DPL_TX Digital Peripheral Link UART data output from LBT 19 DF_DTR Data Fax Data Terminal Ready input to LBT 20 DPL_RX Digital Peripheral Link UART data input to LBT 21 DF_DSR Data Fax Data Set Ready output from LBT 22 DF_CTS Data Fax Clear to Send output from LBT 23 OV Signal ground OV signal reference and return 24 DA_RX PCM digital audio input to LBT 25 OV Signal ground OV signal reference and return 3 3 2 Antenna
15. ront SIM access View 19 28 21 50 11 20 Figure 5 End View 3 3 Interface Connectors The 9522B LBT incorporates four interface connectors Multi Interface Connector located at the right hand end of the bottom of the 9522B LBT Antenna Connector located at the left hand end of the bottom of the 9522B LBT GPS pass thru Connector located in the middle of the bottom of the 9522B LBT Subscriber Identity Module SIM Chip Connector located beneath a cover plate on the front of the 9522B LBT 3 3 1 Multi Interface Connector The multi interface connector is a standard 26 pin 0 1 pitch short latch IDC header with pins in two rows of 13 Connection to this is made using a 26 way IDC without strain relief such as AVX Kyocera 00 8290 026 000 OX 1 or Harting 09 18 526 7803 To support legacy applications a cable is available that converts its pinout to a DB25 connector with the same pinout as the 9522A The connector includes four interfaces Iridium Satellite LLC 9522A L Band Transceiver Product I nformation Guide V1 1 032405 DC Power Control Digital Audio DPL bus RS232 Data Analog Audio The pin out information for this connector is given in Table 3 below The pin out from the DB25 adapter is given in Table 4 below Table 3 26 way connector pin out
16. tions the installer should inform the user that they should not service the 9522B LBT 6 0 Modem Commands and Configuration The 9522B is configured through the use of AT commands A full listing of the supported AT commands can be found in the AT Command Reference document 15
Download Pdf Manuals
Related Search