B M4 COMMISSION REGULATION (EC) No 1275/2008 of 17
Contents
1. 8 9 10 2008R1275 EN 12 09 2013 004 001 3 It has been stated in the preparatory study that standby func tionalities and off mode losses occur for the majority of electrical and electronic household and office equipment products sold in the Community while the annual electricity consumption related to standby functionalities and off mode losses in the Community has been estimated to be 47 TWh in 2005 corresponding to 19 Mt CO emissions Without taking specific measures the consumption is predicted to increase to 49 TWh in 2020 It has been concluded that the electricity consumption of standby func tionalities and off mode losses can be significantly reduced Improvements of electricity consumption of standby func tionalities and off mode losses should be achieved by applying existing non proprietary cost effective technologies which lead to a reduction of the combined expenses for purchasing and operating equipment Ecodesign requirements for the power consumption of standby mode and off mode of electrical and electronic household and office equipment should be set with a view to harmonising ecodesign requirements on standby mode and off mode throughout the Community and contributing to the functioning of the internal market and to improvement of the environmental performance of the products affected The ecodesign requirements should not have negative impact on the functionality of the product and shou2. a 0 Watt consumption state when providing no function The technical feasibility and appropriateness should be considered on a product by product basis in the relevant implementing measure pursuant to Directive 2005 32 EC The two staged entry into force of the ecodesign requirements should provide an appropriate time frame for manufacturers to redesign products as far as standby functionalities and off mode losses are concerned The timing of the stages should be set in such a way that negative impacts related to functionalities of equipment on the market are avoided and cost impacts for manu facturers in particular SMEs are taken into account while ensuring timely achievement of policy objectives Measurements of the power consumption should be performed taking into account the generally recognised state of the art manufacturers may apply harmonised standards in accordance with Article 9 of Directive 2005 32 EC This Regulation should increase the market penetration of tech nologies yielding improved energy efficiency for standby func tionalities and off mode losses leading to estimated energy savings of 35 TWh in 2020 compared to a business as usual scenario Pursuant to Article 8 2 of Directive 2005 32 EC this Regulation should specify that the applicable conformity assessment procedures are the internal design control set out in Annex IV and the management system set out in Annex V to Directive 2005 32 EC In order to
3. including clocks 5 active mode s means a condition in which the equipment is connected to the mains power source and at least one of the main function s providing the intended service of the equipment has been activated 6 off mode means a condition in which the equipment is connected to the mains power source and is not providing any function the following shall also be considered as off mode a conditions providing only an indication of off mode condition b conditions providing only functionalities intended to ensure electromagnetic compatibility pursuant to Directive 2004 108 EC of the European Parliament and of the Council t 7 information technology equipment means any equipment which has a primary function of either entry storage display retrieval transmission processing switching or control of data and of tele communication messages or a combination of these functions and may be equipped with one or more terminal ports typically operated for information transfer 8 domestic environment means an environment where the use of broadcast radio and television receivers may be expected within a distance of 10 m of the apparatus concerned YMI 9 low voltage external power supply means an external power supply with a nameplate output voltage of less than 6 volts and a nameplate output current greater than or equal to 550 milliamperes vM4 10 network means a communication i
4. stage of implementation 2019 The review could address inter alia professional equipment and products equipped with electric motors operated by remote control Article 8 Entry into force This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union Point 1 of Annex II shall apply as from 7 January 2010 Point 2 of Annex II shall apply as from 7 January 2013 Point 3 of Annex II shall apply as from 1 January 2015 Point 4 of Annex II shall apply as from 1 January 2017 Point 5 of Annex II shall apply as from 1 January 2019 Point 6 of Annex II shall apply as from 1 January 2015 Point 7 of Annex II shall apply as from 1 January 2015 This Regulation shall be binding in its entirety and directly applicable in all Member States 2008R1275 EN 12 09 2013 004 001 12 ANNEX I List of energy using products covered by this Regulation 1 Household appliances Washing machines Clothes dryers Dish washing machines Cooking Electric ovens Electric hot plates Microwave ovens Toasters Fryers Grinders coffee machines and equipment for opening or sealing containers or packages Electric knives Other appliances for cooking and other processing of food cleaning and maintenance of clothes Appliances for hair cutting hair drying tooth brushing shaving massage and other body care appliances Scales vVM3 2 Information techn
5. this Regulation if the results for off mode and or standby mode conditions as applicable do not exceed the limit values by more than 0 10 W Otherwise three more units shall be tested The model shall be considered to comply with this Regulation if the average of the results of the latter three tests for off mode and or standby mode conditions as applicable does not exceed the limit values by more than 0 10 W Otherwise the model shall be considered not to comply vVM4 Regarding the requirements set out in Annex II point 2 d Member States authorities shall use the applicable procedure above to measure the power consumption after the power management function or similar function has switched the equipment into the applicable mode or condition Regarding the requirements set out in Annex II points 3 c and 4 a Member States authorities shall use the applicable procedure above after having deac tivated and or disconnected as applicable all network ports of the unit When performing the market surveillance checks referred to in Article 3 2 of Directive 2009 125 EC of the European Parliament and of the Council the Member States authorities shall apply the following verification procedure for the requirements set out in Annex II points 3 and 4 as applicable Member States authorities shall test one single unit as follows If the equipment has as indicated in the technical documentation one type of network po
6. 2008R1275 EN 12 09 2013 004 001 1 This document is meant purely as a documentation tool and the institutions do not assume any liability for its contents gt B gt M4 COMMISSION REGULATION EC No 1275 2008 of 17 December 2008 implementing Directive 2005 32 EC of the European Parliament and of the Council with regard to ecodesign requirements for standby and off mode and networked standby electric power consumption of electrical and electronic household and office equipment lt Text with EEA relevance OJ L 339 18 12 2008 p 45 Amended by Official Journal No page date gt M1 Commission Regulation EC No 278 2009 of 6 April 2009 L 93 3 7 4 2009 gt M2 Commission Regulation EC No 642 2009 of 22 July 2009 L 191 42 23 7 2009 gt M3 Commission Regulation EU No 617 2013 of 26 June 2013 L 175 13 27 6 2013 gt M4 Commission Regulation EU No 801 2013 of 22 August 2013 L 225 1 23 8 2013 2008R1275 EN 12 09 2013 004 001 2 vB vM4 COMMISSION REGULATION EC No 1275 2008 of 17 December 2008 implementing Directive 2005 32 EC of the European Parliament and of the Council with regard to ecodesign requirements for standby and off mode and networked standby electric power consumption of electrical and electronic household and office equipment YB Text with EEA relevance THE COMMISSION OF THE EUROPEAN COMMUNITIES Having regard to the Treaty establishing the European Community Having regard to Di
7. ctivated c Power consumption in a condition providing networked standby The power consumption of HiNA equipment or equipment with HiNA functionality in a condition providing networked standby into which the equipment is switched by the power management function or a similar function shall not exceed 8 00 W The power consumption of other networked equipment in a condition providing networked standby into which the equipment is switched by the power management function or a similar function shall not exceed 3 00 W The power consumption limits as stipulated in point c shall not apply to i large format printing equipment ii desktop thin clients iii workstations iv mobile workstations v small scale servers vi computer servers 5 As of 1 January 2019 In addition to the requirements set out in point 3 a and b and point 4 a b and c the following provision shall apply for networked equipment other than HiNA equipment or other than equipment with HiNA functionality 2008R1275 EN 12 09 2013 004 001 16 vM4 The power consumption of networked equipment other than HiNA equipment or other than equipment with HiNA functionality in a condition providing networked standby into which the equipment is switched by the power management function or a similar function shall not exceed 2 00 W 6 As of 1 January 2015 For coffee machines the delay time after which the product switches a
8. e workstation means a high performance single user computer primarily used for graphics Computer Aided Design software development financial and scientific applications among other compute intensive tasks excluding game play and which is designed specifically for portability and to be operated for extended periods of time either with or without a direct connection to an AC power source Mobile workstations utilise an integrated display and are capable of operation on an integrated battery or other portable power source Most mobile workstations use an external power supply and most have an integrated keyboard and pointing device A mobile workstation has the following characteristics a has a mean time between failures MTBF of at least 13 000 hours b has at least one discrete graphics card dGfx meeting the G3 with FB Data Width gt 128 bit G4 G5 G6 or G7 classifi cation c supports the inclusion of three or more internal storage devices d supports at least 32 GB of system memory 38 small scale server means a type of computer that typically uses desktop computer components in a desktop form factor but is designed primarily to be a storage host for other computers and to perform functions such as providing network infrastructure services and hosting data media and which has the following char acteristics a is designed in a pedestal tower or other form factor similar to those of desktop computer
9. ember States and to the Commission within one month of the decision being taken on the non compliance of the model In addition to the procedures set out above Member States authorities shall use reliable accurate and reproducible measurement procedures which take into account the generally recognised state of the art including methods set out in documents the reference numbers of which have been published for that purpose in the Official Journal of the European Union 2008R1275 EN 12 09 2013 004 001 21 YB ANNEX IV Benchmarks The following benchmarks are identified for the purpose of Annex I Part 3 point 2 to Directive 2005 32 EC Off mode 0 W 0 3 W with hard off switch on the primary side depending inter alia on the characteristics related to electromagnetic compatibility pursuant to Directive 2004 108 EC Standby reactivation function 0 1 W Standby display simple displays and low power LEDs 0 1 W larger displays e g for clocks require more power vM4 Networked standby 3 W for HiNA equipment 1 W or less for non HiNA equipment
10. ents for off mode and or standby mode when the equipment is connected to the mains power source Power management for all equipment other than networked equipment Equipment shall unless inappropriate for the intended use offer a power management function or a similar function When equipment is not providing the main function and other energy using product s are not dependent on its functions the power management function shall switch equipment after the shortest possible period of time appropriate for the intended use of the equipment automatically into standby mode or off mode or 2008R1275 EN 12 09 2013 004 001 14 vM4 another condition which does not exceed the applicable power consumption requirements for off mode and or standby mode when the equipment is connected to the mains power source The power management function shall be activated 3 As of 1 January 2015 a YS Possibility of deactivating wireless network connection s Any networked equipment that can be connected to a wireless network shall offer the user the possibility to deactivate the wireless network connection s This requirement does not apply to products which rely on a single wireless network connection for intended use and have no wired network connection b Power management for networked equipment Equipment shall unless inappropriate for the intended use offer a power management function or a similar funct
11. facilitate compliance checks manufacturers should be requested to provide information in the technical documentation referred to in Annexes IV and V to Directive 2005 32 EC on the operating conditions subject to the definitions of standby off mode and the corresponding power consumption levels Benchmarks for currently available technologies with low standby and off mode power consumption should be identified This helps to ensure wide availability and easy access to information in particular for SMEs and very small firms which further facilitates the integration of best design tech nologies for reducing the energy consumption of standby and off mode The measures provided for in this Regulation are in accordance with the opinion of the Committee established by Article 19 1 of Directive 2005 32 EC 2008R1275 EN 12 09 2013 004 001 5 vB HAS ADOPTED THE FOLLOWING REGULATION v4 Article 1 Subject matter and scope This Regulation establishes ecodesign requirements related to standby and off mode and networked standby electric power consumption for the placing on the market of electrical and electronic household and office equipment This Regulation shall not apply to electrical and electronic household and office equipment placed on the market with a low voltage external power supply to work as intended vB Article 2 Definitions For the purposes of this Regulation the definitions set out in Directive 2005 32 EC sha
12. function or similar function the power consumption data in Watt rounded to the first decimal place the period of time after which the power management function or a similar function switches the equipment automatically into standby and or off mode and or the condition providing networked standby b the power consumption of the product in networked standby if all wired network ports are connected and all wireless network ports are activated c guidance on how to activate and deactivate wireless network ports The power consumption of the product in networked standby as referred to in point b and the guidance as referred to in point c shall also be included in the user manual vM4 2008R1275 EN 12 09 2013 004 001 17 8 Measurements The power consumption referred to in point 1 a and b point 2 a and b points 3 e and 4 c and point 5 and the delay times referred to in point 6 shall be established by a reliable accurate and reproducible measurement procedure which takes into account the generally recognised state of the art 9 Information to be provided by manufacturers For the purposes of conformity assessment pursuant to Article 4 the technical documentation shall contain the following elements a for each standby and or off mode the power consumption data in Watt rounded to the first decimal place the measurement method used a description of how the equipmen
13. he equipment if only this port is used for remote activation the communication protocol used by the equipment If no information is provided the equipment is considered not to be networked equipment unless it provides the functionalities of a router network switch wireless network access point not being a terminal hub modem VoIP telephone video phone 2008R1275 EN 12 09 2013 004 001 18 vM4 c test parameters for measurements ambient temperature test voltage in V and frequency in Hz total harmonic distortion of the electricity supply system information and documentation on the instrumentation set up and circuits used for electrical testing d the equipment characteristics relevant for assessing conformity with the requirements set out in point l c or the requirements set out in points 2 c and or 2 d and or 3 b as applicable including the time taken to automatically reach standby or off mode or another condition which does not exceed the applicable power consumption requirements for off mode and or standby mode In particular if applicable a technical justification shall be provided that the requirements set out in point l c or the requirements set out in points 2 c and or 2 d and or 3 b are inappropriate for the intended use of equipment The need to maintain one or more network connections or to wait for a remotely initiated trigger is not considered a technical jus
14. ion When equipment is not providing a main function and other energy using product s are not dependent on its functions the power management function shall switch equipment after the shortest possible period of time appropriate for the intended use of the equipment automatically into a condition having networked standby In a condition providing networked standby the power management function may switch equipment automatically into standby mode or off mode or another condition which does not exceed the applicable power consumption requirements for standby and or off mode The power management function or a similar function shall be available for all network ports of the networked equipment The power management function or a similar function shall be activated unless all network ports are deactivated In that latter case the power management function or a similar function shall be activated if any of the network ports is activated The default period of time after which the power management function or a similar function switches the equipment automatically into a condition providing networked standby shall not exceed 20 minutes c Networked equipment that has one or more standby modes shall comply with the requirements for these standby mode s when all network ports are deactivated d Networked equipment other than HiNA equipment shall comply with the provisions under 2 d when all network ports are deactivated e P
15. k access point hub modem VoIP telephone video phone 19 networked equipment with high network availability functionality equipment with HiNA functionality means equipment with the functionality of a router network switch wireless network access point or combination thereof included but not being HiNA equipment 20 router means a network device whose primary function is to determine the optimal path along which network traffic should be forwarded Routers forward packets from one network to another based on network layer information L3 21 network switch means a network device whose primary function is to filter forward and distribute frames based on the destination address of each frame All switches operate at least at the data link layer L2 22 wireless network access point means a device whose primary function is to provide IEEE 802 11 Wi Fi connectivity to multiple clients 23 hub means a network device that contains multiple ports and is used to connect segments of a Local Area Network 24 modem means a device whose primary function is to transmit and receive digitally modulated analogue signals over a wired network 25 printing equipment means equipment that generates paper output from electronic input Printing equipment may have additional functions and may be marketed as a multifunctional device or multifunctional product 26 large format printing equipment
16. ld not affect negatively health safety and environment In particular the benefits of reducing the electricity consumption during the use phase should over compensate potential additional environmental impacts during the production phase of equipment having standby functionalities and or off mode losses The application of this Regulation should be limited to products corresponding to household and office equipment intended for use in the domestic environment which for information tech nology equipment corresponds to class B equipment as set out in EN 55022 2006 The scope should be defined such that equipment that is not yet available on the market but have similar functionalities to those products explicitly named in this Regulation are designed to fulfil the requirements When appro priate an amendment to this Regulation can complement the list of products Operating modes not covered by this Regulation such as the ACPI S3 mode of computers should be considered in product specific implementing measures pursuant to Directive 2005 32 EC As a general rule requirements on standby and off mode set out in product specific implementing measures pursuant to Directive 2005 32 EC should not be less ambitious than those set out in this Regulation 11 12 13 14 15 16 17 2008R1275 EN 12 09 2013 004 001 4 In order to prevent unnecessary losses of energy products should ideally enter into
17. ll apply The following definitions shall also apply 1 electrical and electronic household and office equipment hereafter referred to as equipment means any energy using product which a is made commercially available as a single functional unit and is intended for the end user b falls under the list of energy using products of Annex I c is dependent on energy input from the mains power source in order to work as intended and d is designed for use with a nominal voltage rating of 250 V or below also when marketed for non household or non office use 2 standby mode s means a condition where the equipment is connected to the mains power source depends on energy input from the mains power source to work as intended and provides only the following functions which may persist for an indefinite time reactivation function or reactivation function and only an indi cation of enabled reactivation function and or information or status display 3 reactivation function means a function facilitating the activation of other modes including active mode by remote switch including remote control internal sensor timer to a condition providing additional functions including the main function 2008R1275 EN 12 09 2013 004 001 6 4 information or status display means a continuous function providing information or indicating the status of the equipment on a display
18. means printing equipment designed for printing on A2 media and larger including equipment designed to accommodate continuous form media of at least 406 mm width 27 tele presence system means a dedicated system for high definition video conferencing and collaboration which includes a_ user interface a high definition camera a display a sound system and processing capabilities for encoding and decoding video and audio 2008R1275 EN 12 09 2013 004 001 8 vM4 28 household coffee machine means a non commercial appliance for brewing coffee 29 drip filter household coffee machine means a household coffee machine which uses percolation to extract the coffee 30 heating element means a component of the coffee machine which converts electricity into heat to warm up water 31 cup preheating means a function for warming cups that are stored on the coffee machine 32 brewing cycle means the process that has to be completed to produce coffee 33 self cleaning means a process that the coffee machine carries out to clean its interior This process can either be a simple rinse or a washing process using specific additives 34 descaling means a process that the coffee machine carries out to remove totally or partially potential scale in its interior 35 desktop thin client means a computer that relies on a connection to remote computing resources e g computer se
19. n type of network port only one port is available that port is connected to the appropriate network complying with the maximum specification of the port Wireless ports not used shall be deactivated if possible In the event of verification of requirements set out in Annex II point 3 the wired network ports not used shall be deactivated if possible The unit is put in on mode Once the unit in on mode is working properly it is allowed to go into the condition providing networked standby and the power consumption is measured Then the appropriate trigger is given to the equipment through the network port and a check is made whether the equipment is reacti vated If one physical network port is shared by two or more types of logical network ports this procedure is repeated for each type of logical network port with the other logical network ports being logical disconnected The model shall be considered to comply with this Regulation if the results for each type of network port do not exceed the limit value by more than 10 Otherwise three more units shall be tested The model shall be considered to comply with this Regulation if the average of the results for each type of network port of the latter three tests does not exceed the limit value by more than 10 Otherwise the model shall be considered not to comply The Member State authorities shall provide the test results and other relevant information to the authorities of the other M
20. nfrastructure with a topology of links an architecture including the physical components organisa tional principles communication procedures and formats proto cols 11 networked standby means a condition in which the equipment is able to resume a function by way of a remotely initiated trigger from a network connection 12 remotely initiated trigger means a signal that comes from outside the equipment via a network 13 network port means a wired or wireless physical interface of the network connection located on the equipment through which the equipment can be remotely activated 14 logical network port means the network technology running over a physical network port 15 physical network port means the physical hardware medium of a network port A physical network port can host two or more network technologies OJ L 390 31 12 2004 p 24 2008R1275 EN 12 09 2013 004 001 7 vM4 16 network availability means the capability of the equipment to resume functions after a remotely initiated trigger has been detected by a network port 17 networked equipment means equipment that can connect to a network and has one or more network ports 18 networked equipment with high network availability HiNA equipment means equipment with one or more of the following functionalities but no other as the main function s router network switch wireless networ
21. nt in any condition providing only information or status display or providing only a combination of reacti vation function and information or status display shall not exceed 2 00 W Availability of off mode and or standby mode Equipment shall except where this is inappropriate for the intended use provide off mode and or standby mode and or another condition which does not exceed the applicable power consumption requirements for off mode and or standby mode when the equipment is connected to the mains power source 2 Four years after this Regulation has come into force a b c YS d Power consumption in off mode Power consumption of equipment in any off mode condition shall not exceed 0 50 W Power consumption in standby mode s The power consumption of equipment in any condition providing only a reactivation function or providing only a reactivation function and a mere indication of enabled reactivation function shall not exceed 0 50 W The power consumption of equipment in any condition providing only information or status display or providing only a combination of reacti vation function and information or status display shall not exceed 1 00 W Availability of off mode and or standby mode Equipment shall except where this is inappropriate for the intended use provide off mode and or standby mode and or another condition which does not exceed the applicable power consumption requirem
22. oard BOB configurations c is placed on the market with one or more AC DC power supply ies d all processors have access to shared system memory and are independently visible to a single OS or hypervisor Article 3 Ecodesign requirements The ecodesign requirements related to standby and off mode and networked standby electric power consumption are set out in Annex II Article 4 Conformity assessment The procedure for assessing conformity referred to in Article 8 2 of Directive 2005 32 EC shall be the internal design control system set out in Annex IV to Directive 2005 32 EC or the management system set out in Annex V to Directive 2005 32 EC 2008R1275 EN 12 09 2013 004 001 11 Article 5 Verification procedure for market surveillance purposes Surveillance checks shall be carried out in accordance with the verifi cation procedure set out in Annex III Article 6 Benchmarks The indicative benchmarks for the best performing products and tech nology currently available on the market are identified in Annex IV vM Article 7 Revision The Commission shall review this Regulation and present the results of the review to the Consultation Forum no later than 7 January 2016 in the light of technological progress The review will in particular address the scope and the requirements for standby off mode and the appropri ateness and level of the requirements for networked standby with regard to the third
23. ology equipment intended primarily for use in the domestic environment but excluding desktop computers integrated desktop computers and notebook computers as defined in Commission Regulation EU No 617 2013 3 Consumer equipment Radio sets Videocameras Video recorders Hi fi recorders Audio amplifiers Home theatre systems Musical instruments And other equipment for the purpose of recording or reproducing sound or images including signals or other technologies for the distribution of sound and image other than by telecommunications but excluding televisions as defined in Commission Regulation EC No 642 2009 4 Toys leisure and sports equipment Electric trains or car racing sets Hand held video game consoles Sports equipment with electric or electronic components Other toys leisure and sport equipment OJ L 175 27 6 2013 p 13 vM4 2008R1275 EN 12 09 2013 004 001 13 ANNEX IT Ecodesign requirements 1 One year after this Regulation has come into force a b c Y Power consumption in off mode Power consumption of equipment in any off mode condition shall not exceed 1 00 W Power consumption in standby mode s The power consumption of equipment in any condition providing only a reactivation function or providing only a reactivation function and a mere indication of enabled reactivation function shall not exceed 1 00 W The power consumption of equipme
24. ower consumption in a condition providing networked standby The power consumption of HiNA equipment or equipment with HiNA functionality in a condition providing networked standby into which the equipment is switched by the power management function or a similar function shall not exceed 12 00 W The power consumption of other networked equipment in a condition providing networked standby into which the equipment is switched by the power management function or a similar function shall not exceed 6 00 W vM4 2008R1275 EN 12 09 2013 004 001 15 The power consumption limits as stipulated in point e shall not apply to i printing equipment with a power supply of a rated power larger than 750 W ii large format printing equipment iii tele presence systems iv desktop thin clients v workstations vi mobile workstations vil small scale servers viii computer servers 4 As of 1 January 2017 In addition to the requirements set out in point 3 a and b the following provisions shall apply a Networked equipment that has one or more standby mode s shall comply with the requirements for these standby mode s when all wired network ports are disconnected and when all wireless network ports are deacti vated b Networked equipment other than HiNA equipment shall comply with the provisions under 2 d when all wired network ports are disconnected and when all wireless network ports are dea
25. rective 2005 32 EC of the European Parliament and of the Council of 6 July 2005 establishing a framework for the setting of ecodesign requirements for energy using products and amending Council Directive 92 42 EEC and Directives 96 57 EC and 2000 55 EC of the European Parliament and of the Council and in particular Article 15 1 thereof After consulting the Ecodesign Consultation Forum Whereas 1 Under Directive 2005 32 EC ecodesign requirements shall be set by the Commission for energy using products representing significant volumes of sales and trade having significant envi ronmental impact and presenting significant potential for improvement in terms of their environmental impact without entailing excessive costs 2 Article 16 2 second indent of Directive 2005 32 EC provides that in accordance with the procedure referred to in Article 19 3 and the criteria set out in Article 15 2 and after consulting the Consultation Forum the Commission shall as appropriate introduce a separate implementing measure reducing standby losses for a group of products 3 The Commission has carried out a preparatory study which analysed the technical environmental and economic aspects of standby mode and off mode losses The study has been developed together with stakeholders and interested parties from the EU and third countries and the results have been made publicly available OJ L 191 22 7 2005 p 29 4 5 6 7
26. rt and if two or more ports of that type are available one of these ports is randomly chosen and that port is connected to the appropriate network complying with the maximum specification of the port In the event of multiple wireless network ports of the same type the other wireless ports shall be deac tivated if possible In the event of multiple wired network ports of the same type for verifying requirements set out in Annex II point 3 the other network ports shall be deactivated if possible If only one network port is available that port is connected to the appropriate network complying with the maximum specification of the port OJ L 285 31 10 2009 p 10 2008R1275 EN 12 09 2013 004 001 20 vM4 The unit is put in on mode Once the unit in on mode is working properly it is allowed to go into the condition providing networked standby and the power consumption is measured Then the appropriate trigger is given to the equipment through the network port and a check is made on whether the equipment is reactivated If the equipment has as indicated in the technical documentation more than one type of network port for each type of network port the following procedure is repeated If two or more network ports of a type are available one port is chosen randomly for each type of network port and that port is connected to the appro priate network complying with the maximum specification of the port If for a certai
27. rver remote work station to obtain primary functionality and has no rotational storage media integral to the product The main unit of a desktop thin client must be intended for use in a permanent location e g on a desk and not for portability Desktop thin clients can output information to either an external or where included with the product an internal display 36 workstation means a high performance single user computer primarily used for graphics Computer Aided Design software development financial and scientific applications among other compute intensive tasks and which has the following character istics a has a mean time between failures MTBF of at least 15 000 hours b has error correcting code ECC and or buffered memory c meets three of the following five characteristics 1 has supplemental power support for high end graphics i e peripheral component interconnect PCI E 6 pin 12 V supplemental power feed 2 its system is wired for greater than x 4 PCI E on the motherboard in addition to the graphics slot s and or PCI X support 3 does not support uniform memory access UMA graphics 4 includes five or more PCI PCI E or PCI X slots 2008R1275 EN 12 09 2013 004 001 9 vM4 5 is capable of multi processor support for two or more CPU must support physically separate CPU packages sockets i e not met with support for a single multi core CPU 37 mobil
28. s such that all data processing storage and network interfacing is contained within one box b is designed to be operational 24 hours per day and 7 days per week c is primarily designed to operate in a simultaneous multi user environment serving several users through networked client units d where placed on the market with an operating system the operating system is designed for home server or low end server applications 2008R1275 EN 12 09 2013 004 001 10 vM4 e is not placed on the market with a discrete graphics card dGfx meeting any classification other than G1 39 computer server means a computing product that provides services and manages networked resources for client devices such as desktop computers notebook computers desktop thin clients internet protocol IP telephones or other computer servers A computer server is typically placed on the market for use in data centres and office corporate environments A computer server is primarily accessed via network connections and not through direct user input devices such as a keyboard or a mouse A computer server has the following characteristics a is designed to support computer server operating systems OS and or hypervisors and targeted to run user installed enterprise applications b supports error correcting code ECC and or buffered memory including both buffered dual in line memory modules DIMMs and buffered on b
29. t mode was selected or programmed the sequence of events leading to the condition where the equipment automatically changes modes any notes regarding the operation of the equipment e g information on how the user switches the equipment into a condition having networked standby if applicable the default time after which the power management function or similar function has switched the equipment into the applicable low power mode or condition b for networked equipment the number and type of network ports and with the exception of wireless network ports where these ports are located on the equipment in particular it shall be declared if the same physical network port accommodates two or more types of network ports whether all network ports are deactivated before delivery whether the equipment qualifies as HiNA equipment or equipment with HiNa functionality where no information is provided this is considered not to be the case and for each type of network port the default time after which the power management function or a similar function switches the equipment into a condition providing networked standby the trigger that is used to reactivate the equipment the maximum performance specifications the maximum power consumption of the equipment in a condition providing networked standby into which the power management function or a similar function will switch t
30. tification for exemption from the requirements set out in 2 d in the case of equipment that is not defined as networked equipment by the manufacturer 2008R1275 EN 12 09 2013 004 001 19 ANNEX III Verification procedure When performing the market surveillance checks referred to in Directive 2005 32 EC Article 3 2 the authorities of the Member State shall apply the following verification procedure for the requirements set out in Annex II points l a and 1 b or points 2 a and 2 b as applicable For power consumption requirements larger than 1 00 W Member State auth orities shall test one single unit The model shall be considered to comply with the provisions set out in Annex II points l a and 1 b or points 2 a and 2 b as applicable to this Regulation if the results for off mode and standby mode conditions as applicable do not exceed the limit values by more than 10 Otherwise three more units shall be tested The model shall be considered to comply with this Regulation if the average of the results of the latter three tests for off mode and or standby mode conditions as applicable does not exceed the limit values by more than 10 For power consumption requirements smaller than or equal to 1 00 W Member State authorities shall test one single unit The model shall be considered to comply with the provisions set out in Annex II points l a and 1 b or points 2 a and 2 b as applicable to
31. uto matically into the modes and conditions referred to in Annex II point 2 paragraph d shall be as follows for domestic drip filter coffee machines storing the coffee in an insulated jug a maximum of five minutes after completion of the last brewing cycle or 30 minutes after completion of a descaling or self cleaning process for domestic drip filter coffee machines storing the coffee in a non insulated jug a maximum of 40 minutes after completion of the last brewing cycle or 30 minutes after completion of a descaling or self cleaning process for domestic coffee machines other than drip filter coffee machines a maximum of 30 minutes after completion of the last brewing cycle or a maximum of 30 minutes after activation of the heating element or a maximum of 60 minutes after activation of the cup preheating function or a maximum of 30 minutes after completion of a descaling or self cleaning process unless an alarm has been triggered requiring users intervention to prevent possible damage or accident Until the above date the ecodesign requirements set out in Annex II 2 d shall not apply 7 Product information requirements As of 1 January 2015 the following information for networked equipment shall be visibly displayed on manufacturers freely accessible websites a for each standby and or off mode and the condition providing networked standby into which the equipment is switched by the power management
Download Pdf Manuals
Related Search