here - Bibo
Contents
1. for the first time it s important that water is flowing from both the hot and cold outlets when the keys are touched before you switch on the hot water tank If you are self installing vour BIBO please see the appendix Self installation instructions at the back of this manual Once you have flushed 2 litres of water through the system turn the hot tank on using the switch at back of the machine see page 4 of this guide for its location A prompt will appear to check the hot tank is full of water The hot tank will then begin to heat up and the hot water temperature bar will be active on the screen When first used the hot tank will take approximately 5 minutes to get up to maximum temperature The cold tank takes approximately 5 minutes to get to minimum temperature Performance tip Depending on your local water pressure it may be necessary to reduce the flow of water into your BIBO to control the rate at which the water is dispensed particularly from the hot tank If the flow from the hot tap is too fast this may reduce the number of consecutive cups of very hot water available in one go The flow can be adjusted by partly closing the tap on the connector used to connect to your water supply O ERS MANUAL Main features To dispense hot water 00 The BIBO has a safety lock so you must first touch 9 8 then touch Hot water will flow until you touch any key to stop the water 01 01 2010 FRI 08 00 Hot water U2. Classic User s manual Congratulations on your BIBO purchase Congratulations and thank you for buying a BIBO You are moments away from enjoying pure filtered water boiling and chilled at the touch of a button We want you to get the most from your BIBO so before you use it please read this manual carefully If you have any queries once your BIBO is up and running please first refer to this manual it will provide you with helpful and practical advice There are also a number of videos on our website to guide you through using the BIBO www bibowater co uk Please feel free to contact us you have any further queries or to give any feedback on your BIBO or our service Whatever you need our support team is just an email or a phone call away Visit www bibowater co uk contact email help bibowater co uk or call 0800 678 5969 Please note The pictures and diagrams in this manual are for reference only please refer to your BIBO We reserve the right to make corrections or changes to the information provided in this manual without prior notice being given The products functions structures and designs described in this manual have been patented by our company and are thus protected by the UK amp EU patent offices Version number 14040 Copyright 2014 All Rights Reserved O ERS MANUAL Contents Meet your BIBO page 4 BIBO overview Pine OC CCC nel Using your BIBO page 6
3. again after 15 minutes No cold water 3 If left unused for extended period ice can 3 Turn off the power and wait 2 hours before build up in the cold water tank turning It back Drip tray is full Empty water drip tray and dry thoroughly before replacing Machine leakage a 2 Leakage inside the machine 2 off the power and water please contact BIBO New machine Drain 2L of water from each outlet 2 machine has not been used for along 2 Replace the MAXI filter cartridge Odour from water time 3 The filter has not been replaced when 3 Replace the MAXI filter cartridge necessary Your warranty If problems occur with the BIBO please contact BIBO directly via email on help bibowater co uk or call us on 0800 678 5969 Do not attempt to disassemble the BIBO by yourself doing so will invalidate the product warranty and BIBO takes no responsibility for any resulting issues If the BIBO develops any technical problems within the one year warranty period we will repair your BIBO for free You can extend the warranty beyond the first year by visiting our website at www bibowater co uk Appropriate maintenance costs will be charged for any damage that is caused by the misuse of the machine or that is incurred once the warranty period has ended BIBO BRIGHTER WATER Appendices Self installation instructions Please note these instructions should be used in conjunction with this user s manual
4. and the BIBO self installation kit which should have been delivered with your BIBO These instructions should be followed by a plumber kitchen fitter builder water cooler installer or similarly experienced person If at all unsure please call us on 0800 678 5969 and ask to speak to one of our installation team Water Supply Connection In case you need to turn off the mains water supply to you home identify were the tap isolation valve is located If you have a water softener fitted in your home you can safely connect a BIBO to the softened water supply but please bear in mind that anyone on a low sodium diet may be advised to avoid artificially softened water because the softening process replaces calcium ions with sodium ions Water softeners are generally installed to provide water for washing not drinking and most people prefer to drink hard water because it tastes better It s normal therefore to install one un softened drinking water tap to the kitchen sink which is fed direct from the mains Preparation As well as your BIBO the box contains self installation kit consisting of a length of water pipe a T connector a shut off valve and a right angle fitting There is included an additional length of pipe with a straight connector if needed 2 When you ve decided where to locate your BIBO identify a surtable mains cold water supply nearby More often than not this will be under your kitchen sink or behind your d
5. on without filling it with water first the BIBO will trip its thermal overload switch for safety In order to reset this switch first turn off the BIBO at the mains and remove the plug from the wall Let the BIBO cool down for 30 minutes N B The following instructions assume the BIBO is facing you Remove the left hand side panel This is held in by 2x screws at the rear of the panel x at the top amp at the bottom Remove the drip tray then locate x smaller screw to the left of the drip tray space 2 Remove the lid of the BIBO then loosen the 3x screws in the top panel that run in a line on the left from front to back 3 You will now be able to remove the side panel start by pulling it firmly from the rear bottom corner amp easing it slowly out 4 The hot tank is encased in black insulation amp is located at the front of the BIBO The thermal overload switch is in between the two electrical connectors at the front amp at the bottom of the tank T here s a small black button at the centre that you should press to re set A flat blade screwdriver will do this but don t press too hard 5 Re fit the side panel by easing it under the top panel then snapping the bottom into the base of the BIBO Secure it with the 3x screws 2x at the back amp Ix at the front Do not over tighten Finally re tighten the 3x screws securing the top panel amp replace the lid 6 Now plug the BIBO back in amp follow the install amp
6. state if you dont use it for between and 4 hours When sleeping the cold water temperature is unaffected and stays chilled the hot water temperature slowly drops to 60C When the BIBO goes into sleep mode it will display the message shown on screen No 4 overleaf Simply press any key to wake it up again The hot tank will take a few minutes to reach maximum temperature s To activate sleep mode select Power option in ES menu Touch the E key to select Sleeping touch the 8 key to select ON Touch the J key then touch the 8 key to adjust the elapsed time before the BIBO goes to sleep Touch the to save the changes When this option is selected a 9 will appear in the top right corner of the home screen Touch the o a 3 times or wait 30 seconds to return to the home screen BIBO BRIGHTER Saving power mode Sleeping gt Replacement Use to choose Use to choose Use or g to adjust Your BIBO is saving energy Sleeping Power on off mode Sleeping 2 gt Power on off 7 1 hour to choose or to adjust Power on off mode allows you to set your BIBO to come on and go off at different times of day exactly like your central heating There are three timed available when the BIBO can switch itself on then off again Select the Power ope in the menu touch the J key to scroll down to Ane Power on off option Touch the key to select touch the
7. the water is dispensed particularly from the hot tank If the flow from the hot tap is too fast this may reduce the number of consecutive cups of very hot water available in one go The flow can be adjusted by partly closing the tap on the connector used to connect to your water supply O ERS MANUAL Troubleshooting If a fault should occur please first use the troubleshooting guide below to determine the fault type then follow the steps listed to resolve the issue This should help you resolve the fault with the minimum effort If you find that your BIBO is not working properly or if the problem persists your BIBO may need to be professionally repaired Please contact us at help bibowater co uk or call 0800 678 5969 to speak to one of our team FAULT POSSIBLE CAUSE SOLUTION Machine power is not connected Unplug the machine and then plug it back in again check switch is on No water flow 2 Power socket failure 2 Check the socket and fuse 3 Inlet valve closed 3 Check that the water inlet valve is open 4 Water tap blockage or low water pressure 4 Check your water supply pressure Hot tank is not turned on Turn on the hot tank switch at the back WE NER 2 Excessive water use 2 lest again after 5 minutes 3 he machine was in power saving mode 3 Wait for the hot tank to meet maximum temperature Chilled water temperature set too high Check the water temperature settings Excessive cold water use 2 lest
8. Cold water key also A cup of water key Unlock also acts acts as select key in amp cold water key acts as select key in also acts as select as return key in menu mode menu mode key in menu mode menu mode 5 l6 Heating amp hot water temperature bar 14 Chilling amp cold water temperature bar Menu amp set key Water outlet indicator light red for hot blue for cold BIBO BRIGHTER WATER Using your Initial connection to an electrical supply Once your BIBO has been plugged in to a power supply the screen will initially display the BIBO logo this means it is operating correctly Select your preferred language and then follow the instructions on the screen adding hot and cold water to the respective tanks Once the tanks are full water will flow from the outlet at the front of the dispenser 01 01 2010 FRI 08 00 Language 01 01 2010 FRI 08 00 SE English BIBO NS Use to choose Russian Fill hot water tank to fill water 5 01 01 2010 FRI 08 00 01 01 2010 FRI 08 00 AK 01 01 2010 FRI 08 00 Fill cold water tank UV Under test Please wait to fill water till end of process After turning your BIBO on for the first time we suggest you dispense at least 2 litres of water using both the hot amp cold keys Before using your BIBO for the first time Important When using a new or freshly cleaned
9. Important before using your BIBO for the first time Main features e Menu options amp personal settings BIBO information amp maintenance page 14 How to replace the filters How to clean your BIBO Technical information Safety notes Installing your BIBO page 18 Overview o Connection to a water source Troubleshooting Appendices page 20 e Self installation instructions Resetting the thermal overload switch Changing the panels Going on holiday Moving house BIBO BRIGHTER WATER Meet your BIBO overview louch screen panel 2 p 4 5 6 8 Drip tray cover Removable drip tray 2 Water outlets Front panel Overflow reservoir Lid n a a TUR Refrigeration condenser Hot tank switch Water inlet Rear panel Cooling fan Mains fuse Power switch Mains power cable O ERS MANUAL The touch screen panel tk 01 01 2014 08 00 OY 8 2 13 12 17 16 15 14 I 2 3 4 5 6 01 01 2014 08 00 UV filter Child lock Calendar Day Clock Automatic Power saving status icon status icon Month Year 24 hour on off icon mode icon ri 000 8 3 lO 12 Hot water key also Extra hot water key Ambient mixed hot
10. TER WATER 5 Once the UV lamp hem pee replaced you have to instruct the BIBO that there s a new lamp fitted Touch the key once then touch the J key five times to select UV Filter replacement now touch the E key once then the J once then the key to twice to re set the counter to 360 days left After 30 seconds the screen will revert to the home screen If you need more help or information on changing your filters there s a video demonstrating how to replace them both on our website at www bibowater co uk filterchange Cleaning your BIBO Clean your BIBO by simply wiping it down with a damp cloth Soap or any other gentle detergent can also be used if you wish The drip tray can be removed and cleaned in your dishwasher Please don t use harsh detergents concentrated washing up liquid or solvents to clean your BIBO Avoid using anything abrasive such as steel brushes scourers etc to clean the body as it will scratch It s very important that you don t wet the back of the machine whilst cleaning remember it is connected to an electrical supply Technical information SPECIFICATION PARAMETER Electrical specification Voltage 230 Volts Frequency 50 Hertz Power rating 00 Watts Current rating Amps Heating system Power rating 500 Watts Heating capacity 15 Litres hour Hot water temperature 70 96 Adjustable Chilling system Refrigerant RI 34a Power rat
11. Use to choose MMC Ring beep setting You can programme your BIBO to beep every time a key is pressed by choosing Ring from the main menu and selecting whether you want it on or off Ring gt Ring 2 Oval OK Use to choose Use to choose Restore factory settings To restore all settings to factory settings choose Restore from the main menu and then choose ON Restore gt Restore settings Ee Use to choose Use to choose E Use E to confirm USE SELE 08 08 200 amp THU 0919 L 3130 i BIBO BRIGHTER WATER information amp maintenance Replacing the MAXI filter cartridge BIBO s MAXI filter cartridge should be replaced every 6 months the filter needs replacing the BIBO s display will alert you This message will appear once replacement is due 01 01 2010 FRI 08 00 E Replace filter EY You will see the white top of the MAXI filter cartridge towards the back of your BIBO with a handle protruding from tt Turn the handle firmly anti clockwise until the filter cartridge releases then pull it up and out of the BIBO In the event that the cartridge is too stiff to aun it may help to relieve the water pressure in the BIBO To do this turn off the water supply to the BIBO then touch the 8 key to dispense a small amount of cold water The cartridge will now be
12. V key to turn on the first time ae 106 then use the J key to scroll across to the hour setting for when you wish your BIBO to turn itself ON use the 8 or m key to adjust up or down then scroll across to the minute setting and adjust in the same Scroll across to the OFF time setting and adjust accordingly Touch the key so save your changes Using the J key you can scroll down to the second and third time periods if you wish to use them These can be adjusted and saved as above When this option Is selected a will appear in the top right corner of the home screen Touch the o a 3 times or wait 30 seconds to return to the home screen Saving power mode Sleeping Calendar Replacement Power on off Use to choose Use to choose Use Use Use or to adjust When the BIBO goes into power on off mode it will display the following screen in the display Your BIBO is saving energy Wake up 20 16 Power on off OFF e OFF 00 OFF 00 00 00 00 00 00 00 to choose or to adjust 10 O ERS MANUAL If you want to turn your BIBO on before the programmed time touch any key the screen will display this TE Touch the key to confirm you want it to turn on When BIBO switches back on again from the power on off mode the hot tank will take approximately 5 minutes to heat back up to the maximum temperature and the cold ta
13. easier to remove Remember to turn the water supply back on once the new cartridge has been fitted OPEN Rotate firmly anti clockwise to remove the used filter CLOSE Rotate firmly clockwise to install the new filter Remove the new MAXI filter cartridge from its packaging and insert it Then turn firmly clockwise to install Once the MAXI filter has eem replaced you have to instruct the BIBO that there s a new cartridge fitted Touch the key once then touch the J key five times to select UV Filter replacement now touch the E key three times to re set the counter to 180 days left After 30 seconds the screen will revert to the home screen USER S MANUAL Replacing the UV filter lamp The UV filter lamp should be replaced once a year When it needs replacing BIBO s display will alert you This message will appear once replacement is due 01 01 2010 FRI 08 00 Replace UV lamp You will see the white top of the UV filter lamp towards the front of your BIBO When your BIBO was installed you will have been given a white plastic key to release the UV lamp Put the key into the slot indicated above release the latch and rotate the UV lamp anti clockwise to the OPEN position Pull the UV lamp up and out of the BIBO Remove the replacement UV lamp from its packaging and insert it carefully Then rotate it clockwise to the CLOSE position it will click and lock BIBO BRIGH
14. first use instructions on pages 6 12 of this manual BIBO BRIGHTER WATER 21 Changing the coloured side panels Changing the panels BIBO s coloured side panels can be changed in the event of a kitchen redecoration or a move New panels are available to purchase from our website www bibowater co uk In order to change the panels first turn off the BIBO at the mains and remove the plug from the wall Let the BIBO cool down for 30 minutes N B The following instructions assume the BIBO is facing you Remove the left hand side panel This is held in by 2x screws at the rear of the panel x at the top amp at the bottom Remove the drip tray then locate smaller screw to the left of the drip tray space 2 Remove the lid of the BIBO then loosen the screws the top panel that run a line on the left from front to back 3 You will now be able to remove the side panel start by pulling it firmly from the rear bottom corner amp easing it slowly out 4 Repeat the process with the 3x screws the top panel that run in a line on the right from front to back and remove the right hand panel 5 Re fit the new side panels by easing then under the top panel then snapping the bottom into the base of the BIBO Secure them with the 6x screws down either side and the 2x at the back amp Ix at the front Do not over tighten Finally re tighten the 3x screws securing the top panel amp replace the lid Preparing
15. highlighted in IST Then touch FE to select that option Touching D at any time will take you back to the previous screen Touch 8 and or m to adjust the option settings Water temperature settings Select the temperature Temp setting in the menu then follow the screen prompts to set the hot cold amp ambient mix water temperatures as follows 59 ES C to choose to choose to choose or to set temp or to set temp or to set temp to choose Or to set temp O ERS MANUAL Water quantity settings Select the water quantity QTY setting in the menu then follow the screen prompts to set the hot cold amp ambient mix water quantities as follows QTY HS Temp Calendar Use to choose Use to set Oty Use to set Qty 150 mi Use or to set Qty T Time setting year month day Select Calendar settings and enter the time adjustment screen Follow the prompts to set the date time and your preferred time format as follows Touch to save your selections Calendar Set time and date 0 0 j Date 2010 01 01 _ Time 0B 00 2 7 Time Format 24 H Use to choose Use to choose Use or o to adjust Energy saving mode The BIBO has two energy saving options a sleep mode and a power off mode Sleep Mode Sleep mode allows you to set your BIBO to go into a low power
16. ing 38 Watts Cooling capacity 5 Litres hour Cold water temperature 4 6 C Adjustable Filtration system Activated carbon filter 0 5 Micron UIN Watts Inlet water pressure IMinimum Maximum bar 14 5 6 bar 87psi Dimensions mm SU AT a 218 Weight 17 Kgs GB4 06 1 2005 GB47 06 3 2008 Operating standards 4706 19 2008 GB 1 22090 2008 The maximum ambient working temperature Is 38 C The dispense capacity is calculated at an ambient and inlet water temperature of 25 C Safety notes his BIBO is for indoor use only Avoid placing it in direct sunlight or next to flammable materials Avoid placing the BIBO near other appliances that could get damaged if wet Do not immerse the BIBO in water he BIBO uses 230VAC voltage and should be used with a OA fuse in the plug top e Important when using a new or freshly cleaned BIBO for the first time it s important that water is flowing when both the hot and cold water keys are touched before you switch on the hot water tank he BIBO dispenses safe and great tasting drinking water The tanks are not pressurised and the hot tank is directly connected to the hot water outlet No valves are used so it is normal therefore for a small amount of excess water to be released once water has been dispensed BIBO can produce high temperature hot water As with any kettle pan or appliance capable of producing hot water please use caution when dispensing hot wate
17. ishwasher or washing machine Ideally this should be a 5mm copper pipe in good condition with enough of the pipe exposed to enable you insert the BIBO T connector 3 Often there is a valve to enable you to isolate the chosen pipe If not then it will be necessary to turn off the main water supply to your home Be sure to drain as much water as possible from the pipe before cutting it Using a suitable pipe cutter make two cuts in the pipe removing a 20mm section Push the two exposed ends of the copper pipe firmly into each end of the BIBO connector Make sure the tap on the BIBO T connector is turned off i e parallel to the copper pipe c cO E Turn the water supply back on and make sure there are no leaks where the copper pipe fits into the BIBO CONDE COI co Push the 6mm white water supply pipe provided with your BIBO firmly into the fitting on the piece 9 Run this pipe behind or underneath your kitchen base cabinets then bring it up through the worktop behind your BIBO IO Push the end of the pipe into the blue amp white shut off valve supplied with the connector Installation Safety tips e Remember your BIBO weighs 7kgs so take care when lifting it from its box Install your BIBO in a cool dry place where it is well ventilated It must be kept away from any heat source Keep the rear of your BIBO at least 5cm 27 away from the wall The water pressure should be betwee
18. lifting it It s important that your BIBO is kept upright during transportation BIBO BRIGHTER WATER 25 www bibowater co uk Call us free on 0800 678 5969
19. me and other settings are correct If not then follow the instructions on pages 8 9 and 10 of your BIBO User s Manual Disconnecting your BIBO when moving home Turn off the water supply to your BIBO where it is connected to your mains water pipe Normally this connection consists of a white plastic T connector with an integral shut off valve Turn the water off by twisting the grey lever through 90 degrees If the connection is by way of a traditional washing machine type valve twist the blue lever through 90 degrees 2 Backat your BIBO touch the g to relieve any pressure in the pipe A small volume of water may be dispensed Touch the key again 3 Flick the power and hot tank switches at the back of your BIBO to off 0 4 Atthe water connection on the back of your BIBO twist the blue tap lever so it s at right angles to the water pipe Where the pipe enters the tap depress the collar and remove the pipe 5 This length of water pipe should NOT be used again but can be removed from behind under your kitchen units and disconnected from the connector or washing machine valve 6 If required a black blanking plug is available to fill the small hole in your worktop 7 re install your BIBO in your new home please follow the relevant sections of the self installation instructions in Appendix of the BIBO user s manual Safety tips As your BIBO is full of water it now weighs 20kgs so take care when
20. n 14 5 5 and 6bar 87psi Your BIBO needs a normal 3amp power supply 20 O ERS MANUAL Carefully remove the packaging and place your BIBO in its preferred location on the work surface Remove the plastic bag and protective covering from the cable and plug Remove the drip tray wrapping and the UV lamp key keep this in a safe place from inside the drip tray Remove the protective cover from the touch screen UE S Remove the blue locking clip from the inlet water fitting on the back of your BIBO depress the collar on the fitting then remove the blanking plug see the pictures on page 18 of this manual for guidance 6 Push the right angle water fitting supplied with the BIBO self installation kit into the water inlet then replace the blue locking clip 7 Push the short length of pipe from the shut off valve into the right angle fitting Setting Up Safety tip Make sure both power switches on the back of your BIBO are in the off position before connecting to the power supply see the illustration on page 4 of this manual for guidance Now follow the instructions called Using Your BIBO on pages 6 12 of this manual and follow the BIBO s on screen prompts If you have any questions please call us 0800 678 5969 Re setting the hot tank thermal overload switch Instructions to reset the BIBO hot tank thermal overload switch In the unlikely event that you turn your BIBO s hot tank
21. nk will take approximately 15 minutes to chill back down to the minimum temperature Child lock setting To set the extra child lock select the Child lock option from the menu Follow the prompts to turn the child lock on or off Child lock Child lock 0 Once the child lock has been set it will only be possible to dispense hot water by touching the J key for more than 3 seconds after you have touched the MAXI filter amp UV filter maintenance settings To see how long is left on the lives of your two filters select UV filter replacement from the main menu For the MAXI filter select Filter and the screen will tell you how long is left until you need to change it for a new one Replacement Replace Filter leise A 4 Filter gt Changed new one Power 4 Language 90 Days left Use to choose Use to choose Use to confirm gt UV lamp A Changed new one Power Gin Language 90 Days left Use to choose Use to choose Boman BRIGHTER WATER pum L Hu Language v Restore Language settings You can change the operating language of BIBO at any time by choosing Language from the main menu and selecting your preferred language from the options available Language Language Be 22 Replacement Russian English Use to choose
22. r When your BIBO is turned on for the first time or after a period of not being used please run at least 2 litres of water through both the hot and cold outlets before drinking any to ensure the water is fresh e Warning The BIBO must be used with a reliable earth in the mains power supply socket For further notes or detailed explanations on the operation of the machine please contact BIBO via email at help bibowater co uk BIBO BRIGHTER WATER 17 Installation Your BIBO may have been installed by one of our professional experienced installation team However please note the following concerning the installation of your BIBO Overview Install the BIBO in cool dry place where it is well ventilated It must be kept away from any heat source he rear of the BIBO will get warm so please keep it at least 5 27 away from the wall to ensure that this part of the dispenser is well ventilated Water supply connection The water pressure should be between 14 5psi and 6bar 87psi Remove the blue locking clip from the inlet water fitting Depress the collar then remove the blue blanking plug Picture Insert the water pipe Picture 2 Replace the blue locking clip Picture 3 l Picture 2 Performance tip Depending on your local water pressure it may be necessary to reduce the flow of water into your BIBO to control the rate at which
23. se any key to stop Boling Please wait End of boiling Once boiling has finished you can dispense water from the BIBO To dispense cold water is Touch then cold water will flow until you touch any key to stop the water 01 01 2010 FRI 08 00 e Cold water Use any key to stop To dispense ambient mixed water Touch then ambient water a mixture of hot amp cold water will flow at the temperature and volume you have set You can however touch any key to stop the water 01 01 2010 FRI 08 00 45 Mix water 150ml BIBO BRIGHTER WATER To dispense measured cup of hot or cold water 00 Touch g then touch either J or for a measured cup of hot or cold water To set the quantity of how much water the will dispense please see page 9 in this manual 01 01 2010 FRI 08 00 01 01 2010 FRI 08 00 01 01 2010 FRI 08 00 _ Ww cold water for a cup Menu options amp personal settings The menu allows you to control temperature settings water quantity settings time and date settings energy saving mode child lock settings filters and UV lamp change settings language settings ring tone settings and there s also an option to restore BIBO s factory settings To enter the menu Touch FE on the panel then follow the on screen prompts 00 Touch J to scroll through the menu options until the one you wish to change is in the centre of the screen
24. your BIBO for when you are going on holiday How to prepare your BIBO for when you are going on holiday If at all unsure how to proceed please call us on 0800 678 5969 and ask to speak to one of our installation team Before you go Flick the hot tank switch located at the back of the BIBO next to the power switch to off Do not switch off the power switch as this may affect the BIBO settings 2 Turn off the water supply to the BIBO by twisting the blue tap at the back of the BIBO so that the lever is at right angles to the white water pipe When you come back Turn on the water supply to your BIBO by twisting the blue tap so the lever is in line with the water pipe 2 Flick the hot tank switch at the back your BIBO to on 1 00 w 3 Touch the hot water key make sure the water flows and then touch the hot water key J again to stop 4 The hot water tank will now begin heating 5 It s a good idea to rinse fresh water through both tanks so remove the drip tray amp place a jug or similar of at least 2Itrs capacity under the taps then follow steps and 8 below 6 Touch the cold key V and allow the water to run until it stops automatically after dispensing approximately I 5ltrs w 7 Repeat this process by touching the hot key VJ NB the water will be hot 27 USER S MANUAL 8 The hot tank will now take approximately 5 minutes to reach maximum temperature 9 Check that the day date ti
Download Pdf Manuals
Related Search