Home

(DVD/BD) User Manual - DISC Archiving Systems

1. CAUTION If your Optical Library is equipped with a redundant PSU you always should connect both line voltage cables In order to get a high availability system it is recommended to connect each line voltage cable to a different power circuit WARNING The Optical Library is not electrically disconnected from line voltage when powered down To electrically disconnect the Optical Library from line voltage you must disconnect the power cord CAUTION The DISCx000 Optical Library must be connected to an electrical circuit that is secured with a 16 Amp fuse WARNING In case of a failing PSU the Optical Library case has to be opened for exchange Opening of the covers and service interaction must be done by skilled service staff only DISCx000 Version 2 2User Manual 40 KAPITEL 4 SETUP 143714 F DISCx000 Version 2 2User Manual Rev B 4 KAPITEL 4 SETUP lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 42 KAPITEL 5 ARBEITEN MIT DER OPTICAL LIBRARY CHAPTER 5 OPERATING THE OPTICAL LIBRARY Powering on the Optical Library Handling Media Importing and Exporting Media The Mailslot Using Packs 143714 F DISCx000 Version 2 2User Manual Rev B 43 KAPITEL 5 ARBEITEN MIT DER OPTICAL LIBRARY lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 44 KAPITEL 5 ARBEITEN MIT DER OPTICAL LIBRA
2. 91 4 F temperature Gradient of 11 C h 11 C h 11 C h 11 C h temperature 19 8 F h 19 8 F h 19 8 F h 19 8 F h Relative humidity 10 68 10 68 10 68 10 68 operating non condensing non condensing non condensing non condensing Power Supply Line voltage 90 120 V 4A 90V 120 V 5A 90V 120 V 5A 90V 120 Frequency range Power consumption 220 V 240 A 50 60 Hz 220 V 240 A 50 60 Hz 220 V 240 A 50 60 Hz 220 V 240 V 5 A 50 60 Hz normal Power consumption 140W 140W 155W 180W max 345 W 345 450 W 920 W 143714 DISCx000 Version 2 2User Manual Rev B 75 ANHANG A TECHNISCHE DATEN DISC1000 DISC3000 DISC4000 DISC7000 Dimensions and Weight Width JB JB incl 300 mm 365 620 5 mm 365 620 5 mm 365 835 mm Stands Height 410 mm 780 mm 980 mm 1500 mm Depth 680 mm 730 mm 730 mm 730 mm Weight without 35 kg 54 kg 72 kg 95 kg media FUSES Internally used Fuses PCB Silkscreen Overlay Top Side Mount Fuse 5A 63V quick acting Main Controller 511 S12 Mount Fuse 2A 63V quick acting Main Controller 13 Mount Fuse 2A 125V slo blo LKU Board 511 SPECIFICATIONS DISC1000 DISC30
3. S ve GES y DISC1000 DISC3000 DISC4000 DISC 7000 User Manual DISCx000 Version 2 2User Manual Chapter 1 Copyrights Trademarks and Contact Information 6 Notice of Copyright 8 Changes 8 Trademarks Used in this Manual 9 Contacting DISC 9 International 9 Internet 9 Mailing Address 9 Sales 9 Technical Support 9 Chapter 2 Safety Instructions 13 Intended Use 15 Use of Interjective Terms 15 Ban on Arbitrary Reversions and Changes 15 Repairs 15 Fire and Shock Hazard 16 Opening the Unit 16 Safety 16 Data Security 16 Electromagnetic Compatibility 17 Fuses 17 Professional Disc Media 17 Chapter 3 Overview 19 DISC1000 Components 21 DISC3000 Components 22 DISC4000 Components 23 DISC7000 Components 24 Installed Equipment 25 Structure of Model Designation 25 DISCx000 AA XXX M 25 Example of Model Designation 26 DISC3000 4 225 RM 26 DISCx000 Front 26 Keyboard 27 LCD 27 DISCx000 Rear 28 DISCx000 Rear Side View behind the backplane 29 LVD equipped DISCx000 30 Chapter 4 Setup 31 Checking the Delivery 32 Equipment 32 Quantity 32 Removing the Transportation Fixtures 34 143714 F DISCx000 Version 2 2User Manual Rev B 2 Mounting the Stands 35 Placing the Optical Library 36 Operation Modes 37 Mode 37 Function 37 Function of ID Switch 37 RS232 Mode 37 SCSI Mode 38 SCSI Cable Requirements 38 SCSI Cable Length 38 Setting Drive SCSI IDs 38 Connecting to a Host Computer 3
4. TECHNICAL SUPPORT Phone 49 0 6721 964 222 Fax 49 0 6721 964 245 E Mail support disc gmbh com Before contacting DISC Technical Support please have the following information available Model Serial Number and production date of your Optical Library Description of Optical Library environment Operating System software revision and hardware Detailed description of the problem 143714 F DISCx000 Version 2 2User Manual Rev B 9 143714 F DISCx000 Version 2 2User Manual Rev B 10 CHAPTER 2 SAFETY INSTRUCTIONS Intended Use Residual Risks Safety 143714 F DISCx000 Version 2 2User Manual Rev B lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 12 Verwendung von Abk rzungen DISCx000 DICC1000 DISC3000 DISC4000 DISC7000 INTENDED USE The DISCx000 Optical Libraryes are controlled by a host computer or combined server unit NAS The Optical Libraryes were designed exclusively to read and write bare media especially the Blue Laser PDD PD BD media and are not intended for any other use Improper use of the Optical Library increases residual risk Any person using the Optical Library should read and understand the User Manual and in particular the safety instructions included within the User Manual UsE OF INTERJECTIVE TERMS WARNING This word calls attention to a procedure or practice which could cause personal injury if
5. KAPITEL 3 UBERSICHT DISC 1000 COMPONENTS 3 or 4 removable Packs holding 15 media each 1 Mailslot for importing and exporting media Up to 2 drives CapacityDoubler flipper unit optional for DVD RAM and DVD R machines only Up to 2 data interfaces 160 MB s LVD SCSI a 1 robotic interface RS232 or LVD SCSI DISC1000 105 2 Optical Libraryes have 4 Packs rather than 3 and will have filled up the empty rear side drive bays with additional Magazines holding 15 media each DISC1000 45 1 DISC1000 105 2 Pack 15 Noticensed Pack 1506 Pack iss Pack 15 slots Not licensed Pack 15 slots Pack 16 slots 5 Pack tse I 5 Leer amp Notlcensed 2 Pack 15808 te Lift Mechanism Lift Mechanism Fixed Number of Media Slots 45 Variable Number of Media Slots 105 Drive 2 Drives 143714 F DISCx000 Version 2 2User Manual Rev B 19 KAPITEL 3 UBERSICHT DISC3000 COMPONENTS 2 or 3 Magazines holding 50 media each 143714 F Rev B 3 or 4 removable Packs holding 15 media each 1 Mailslot for importing and exporting media Up to 6 drives Up to 4 data interfaces SCSI 2 or LVD 1 robotic interface RS232 or SCSI The DISC3000 with 145 slots can be upgraded to a DISC3000 with 270 slots or 210 slots and 6 Drives DISC3000 with 270 slots Optical Libraryes have 4 Packs rather than 3 3 Magazines rather than 2 and wi
6. Tray Refer to the User Interface Diagram on page 54 to determine which sub menu contains the command you wish to execute Once you select the function within the Operate menu that you desire the Optical Library User Interface will prompt you for pertinent information needed to execute the command Typical information that you will be prompted for includes The address of a tray Location front or rear of the Optical Library Position bay of the magazine Position of the tray within the magazine This type of query is answered by entering the 5 digit location address and pressing Enter Location address parameters are listed in the table below Address Digit This Digit Represents Available Range to Input 1 Location front or rear of 1 front or 2 rear Optical Library 2 and 3 Position bay of magazine 1to 17 4 and 5 Position of tray inside 01 to 50 magazine 143714 F DISCx000 Version 2 2User Manual Rev B 58 KAPITEL 6 DIE BENUTZEROBERFLACHE Element Load Mailslot Tray 1 Front gt X lt 2 Rear Tray Bay gt YY lt 1 17 Tray Tray gt ZZ lt 1 50 The available commands within the Operate menu along with their functions are listed in the table below Command Functionality Load Mailslot F111 Used to import and export a single medium After completing the command press enter to import or export another mediu
7. more information see The User Interface on page 53 To exit the User Interface go to the menu root 1 and press Esc The User Interface will also automatically exit after 10 minutes when no button is pressed within a submenu USER INTERFACE MODES The Optical Library User Interface is used to configure and operate the Optical Library without using a host computer The User Interface has 3 modes User Mode Admin Mode a Service Mode Access to User Mode is available to any user You must first enter the correct Admin PIN to access the Admin Mode and the correct Service PIN to access the Service Mode Service Mode is for trained technicians only and should not be accessed if you are not a DISC authorized service provider Refer to the table below to determine what functional areas are part of which mode 143714 F DISCx000 Version 2 2User Manual Rev B 54 KAPITEL 6 DIE BENUTZEROBERFLACHE User Interface Mode Functional Areas Available User Mode Info PIN Codes Admin Mode Operate Settings Service Mode Service Demo System Control USER MODE DISC x000 U VXXXX 01 07 05 User Menu Select Item In the User Mode only the Info and PIN Codes menus and few parts of the Operate menu e g import and export of media are available In this mode no settings can be changed or operations performed except for entering or changing Admin or Servic
8. not correctly performed CAUTION This word calls attention to a procedure or practice which could result in damage to the product if not correctly performed NOTE This word draws the users attention to information that can improve understanding of the product Disregarding safety messages could result in personal injury or damage to the Optical Library BAN ON ARBITRARY REVERSIONS AND CHANGES The Optical Library must not be altered or changed in any way that does not comply with applicable safety regulations REPAIRS 143714 F Rev B Repairs must be carried out only by DISC staff or DISC authorized service providers DISC will not be liable for any damage caused from repair by unauthorized individuals Repair by unauthorized individuals may void your warranty DISCx000 Version 2 2User Manual 13 FIRE AND SHOCK HAZARD To prevent fire and electrical shock do not expose the unit to rain or moisture OPENING THE UNIT To prevent electrical shock remove line cord before opening the unit CAUTION Do not operate the Optical Library while covers are removed Ambient light and dust will interfere with Optical Library operation and moving parts increase risk of personal injury The exchange of the air filter be done as hot swap operation without a need to open the Optical Library SAFETY This product is in the used way a Laser Class 1 device Disc access is accomplished via a laser beam T
9. uses Low Voltage Differential LVD technology ensure that all SCSI cables and terminators support LVD SCSI CABLE LENGTH To connect the Optical Library to the SCSI host adaptor only cables that do not exceed 10 meters cable length may be used SETTING DRIVE SCSI IDS The ID switches on the rear of the Optical Library are used to set drive SCSI IDs only DISC 3 7000 The ID range for each drive is 00 to 07 Each drive on any given bus must have a unique ID If more than one SCSI bus is installed you use a small screwdriver to adjust the switches to the desired IDs The factory default for DISC1000 is ID 01 and 02 NOTE Most host applications require to have the ascending order of SCSI IDs according to the physical position of the drive within the Optical Library counted from bottom to top 143714 F DISCx000 Version 2 2User Manual Rev B 36 KAPITEL 4 SETUP SCSI A De SCSI B Ds 3k D4 2 SCSI C Gi Ke D2 d D 1 SCSI D CAUTION f the robotic interface is set to SCSI mode do not switch a drive to the same SCSI ID CONNECTING TO A HosT COMPUTER CONNECTING THE SERIAL INTERFACE CAUTION Shut down the Optical Library and host computer before connecting cables Depending upon host software used to control the Optical Library either the serial interface or SCSI interface must be connected to the host computer This section pertains to systems connected to the host via a serial interfac
10. 0 1 Remove the 14 screws that affix the right cabinet cover of the Optical Library 2 Remove the right cabinet cover 3 Remove the transportation fixtures inside the Optical Library ATTENTION u u When removing the LV transportation lock please carefully protect the black flexible cable from bending Transportation twisting other Fixtures H mechanical damage Such damage may impact the proper function of the library u ESD Cable ISS I CAUTION Powering on the Optical Library with transportation fixtures inside can damage the robotics Do not operate the Optical Library while covers are removed Ambient light will interfere with Optical Library operation and moving parts increase risk of personal injury 143714 F DISCx000 Version 2 2User Manual Rev B 32 KAPITEL 4 SETUP MOUNTING THE STANDS WARNING Do not operate the Optical Library without the stands installed 5 69 Regulations require the stands to be installed Mounting the Optical Library Stands DISC3 7000 NOTE Two people are required to perform this procedure 1 Tilt the Optical Library to the left 2 Push the front stand for the right side into the slot near the bottom of the Optical Library until it clicks in 3 Push the rear stand for the right side into the slot near the bottom of the Optical Library until it clicks in Tilt the Optical Library to the right Push the front stand for the left side in
11. 00 DISC4000 DISC7000 Robotics Media Exchange 2 second 3 second 4 second 6 second Time avg Reliability MSBF 2 500 000 cycles 2 500 000 cycles 2 500 000 cycles 2 500 000 cycles Drives Read write drive Professional Disc for Data DVD PDD BD DVD PDD BD DVD PDD BD DVD PDD BD 143714 F Rev B DISCx000 Version 2 2User Manual 76 ANHANG TECHNISCHE DATEN SLOT UPGRADES 143714 F Rev B DISC DISC1000 DISC3000 DISC 4000 and DISC7000 Optical Libraryes are available in two capacities DISC1000U 45 media slots DISC1000 up to 105 media slots DISC3000U 145 media slots DISC3000 up to 270 media slots DISC4000U 145 media slots DISC4000 up to 400 media slots DISC7000U 510 media slots DISC7000 up to 690 media slots The basic Optical Library is the DISCx000 version the upgrade to full capacity is optional Slot upgrades must be completed in the factory or on site by specially trained service staff The slot upgrade is not available as a standard field upgrade kit For more information about slot upgrades contact your DISC sales office DISCx000 Version 2 2User Manual 77 ANHANG TECHNISCHE DATEN lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 78 Index 143714 F DISCx000 Version 2 2User Manual Rev B Index A agenc
12. 61000 3 2 2000 EN 61000 3 2 2000 EN 61000 3 3 1995 A1 2001 EN 61000 3 3 1995 A1 2001 EN 61000 3 3 1995 A1 2001 EN 60950 UL 1950 CUL C22 2No 950 EN 60950 UL 1950 CUL C22 2No 950 EN 60950 UL 1950 CUL C22 2No 950 Sicherheit von Einrichtungen der Safety of information technology S curit des mat riels de traitement de Informationstechnik equipment l information Das Qualit tssicherungssystem von DISC DISC quality assurance system assures La syst me d assurance de la qualit de garantiert die Konformitat compliance DISC garantit la conformit Hersteller Manufacturer Fabricant DISC GmbH DISC GmbH DISC GmbH Im Tiergarten 24 Im Tiergarten 24 Im Tiergarten 24 D 55411 Bingen am Rhein D 55411 Bingen am Rhein D 55411 Bingen am Rhein Ausstelldatum 02 06 2005 Date of issue of the declaration Date d tablissement 7e la declaration 02 06 2005 02 06 2005 the Soo W Beckmann H Schellong Managing Director Director Development 143714 F DISCx000 Version 2 2User Manual Rev B 69 ANHANG B BEHORDLICHE GENEHMIGUNGEN DECLARATION OF CONFORMITY DISC4000 EG Konformitatserklarung EC Declaration of Conformity CE D claration de Conformit mit den Richtlinien 89 336 EWG und 73 per 89 336 EEC and 73 23 EWG avec 89 336 CEE et 73 23 EWG 23 EWG Hiermit wird bestatigt dass das Produkt This is to confirm that the product Nous d clarons que
13. 9 Connecting the Serial Interface 39 Connecting the SCSI Interface 40 Connecting Line Voltage 41 Chapter 5 Operating the Optical Library 45 Powering on the Optical Library 47 Handling Media 48 Handling Exposed Media 48 Handling Packs 48 Importing and Exporting Media 49 The Mailslot 49 Using Packs 50 Removing Packs 50 Action 51 Status 51 Display 51 Inserting Packs 51 Action 51 Status 51 Display 51 Chapter 6 The User Interface 53 The User Interface 55 Activating the User Interface 56 User Interface Modes 56 User Interface Mode 57 Functional Areas Available 57 User Mode 57 Info Menu 57 Info Menu Sub Menu 58 143714 F DISCx000 Version 2 2User Manual Rev B 3 Available Information 58 PIN Codes Menu 59 Admin Mode 59 Operate Menu 60 Address Digit 60 This Digit Represents 60 Available Range to Input 60 Command 61 Functionality 61 Settings Menu 63 Machine Defaults 63 Auto Disc 63 Auto Start 63 TCP IP for use at embedded NAS machines only 63 Parameter 64 Function 64 Service Mode 65 Agency Approvals 67 Agency Approvals 69 FCC Declaration 69 Declaration of Conformity DISC 1000 70 EG Konformitatserklarung 70 EC Declaration of Conformity 70 CE D claration de Conformit 70 Declaration of Conformity DISC3000 71 EG Konformitatserklarung 71 EC Declaration of Conformity 71 CE D claration de Conformit 71 Declaration of Conformity DISC4000 72 EG Konformitatserklarung 72 EC D
14. CSI interfaced systems connect to the first SCSI bus SCSI A on the Optical Library The DISC7000 Optical Library can be equipped with 1 to 6 SCSI busses SCSI A SCSI F the DISC3000 and DISC4000 can be equipped with 1 to 4 SCSI busses SCSI A SCSI D and the DISC1000 with 1 SCSI bus DISCx000 Version 2 2User Manual 38 KAPITEL 4 SETUP 1 Host computer 2 SCSI bus A to host computer connection 3 SCSI bus B to host computer connection 4 SCSI bus C to host computer connection CAUTION LVD equipped Optical Libraryes require term power from the bus The host computer must be powered on for the Optical Library to start up or operate CONNECTING LINE VOLTAGE 143714 F Rev B Before connecting the Optical Library to the electrical outlet mount the ferrite to the power cord as close to the Optical Library as possible All DISC Optical Libraryes have auto switching power supplies No adjustment is needed to switch between 110 volt and 220 volt electrical systems All DISCx000 Optical Libraryes can either be equipped with a standard or dual redundant power supply unit In case one of the PSU modules is failing or temporarily not connected the Optical Library can run with the remaining one An acoustic alarm beep is given until the failing module has been exchanged or the missing mains cable is connected again DISCx000 Version 2 2User Manual 39 KAPITEL 4 SETUP 143714 F Rev B
15. CY APPROVALS FCCDeclaration Declaration of Conformity 143714 F DISCx000 Version 2 2User Manual Rev B 65 ANHANG B BEHORDLICHE GENEHMIGUNGEN lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 66 ANHANG B BEHORDLICHE GENEHMIGUNGEN AGENCY APPROVALS 143714 F Rev B FCC DECLARATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Important This product was FCC
16. HE GENEHMIGUNGEN DECLARATION OF CONFORMITY DISC3000 EG Konformitatserklarung EC Declaration of Conformity CE D claration de Conformit mit den Richtlinien 89 336 EWG und 73 per 89 336 EEC and 73 23 EWG avec 89 336 CEE et 73 23 EWG 23 EWG Hiermit wird bestatigt dass das Produkt This is to confirm that the product Nous d clarons que le produit PDD Optical Library PDD Optical Library Optical Library PDD DISC 3000 DISC 3000 DISC 3000 mit den folgenden Normen bzw normativen is in compliance with the following est conforme aux normes ou autres Dokumenten Ubereinstimmt standards or other normative documents documents normatifs suivants EN 55022 1998 A1 2000 EN 55022 1998 A1 2000 EN 55022 1998 A1 2000 Grenzwerte und Messverfahren fur Limits and methods of radio interference Limites et m thodes de mesure des Funkst rungen von informationstechnischen characteristics of information technology charact ristiques de perturbation Einrichtungen equipment radio lectriques produites par les appareils de traitement de l information EN 50024 1998 A1 2001 EN 50024 1998 A1 2001 EN 50024 1998 A1 2001 St rfestigkeit von informationstechnischen Information technology equipment Appareils de traitements l information Einrichtungen Immunity Characteristics Limits and characteristiques d immunit limites et methods of measurement m thodes de mesure EN 61000 3 2 2000 EN
17. RY POWERING ON THE OPTICAL LIBRARY Always power on the Optical Library before the host computer Failure to do so may result in the host not recognizing the Optical Library and being unable to interface with it CAUTION LVD equipped Optical Libraryes require term power from the bus The host computer must be powered on simultaneously for the Optical Library to start up or operate To power on the unit press the red power button on the front of the Optical Library The display will show Booting and then change to Reading License Data and finally change to DISC4000 V4508 N1170 During boot up the robotics will rezero While this is occurring you will hear mechanical noises from the unit The Optical Library robotics are normally controlled via a host software application For information on how to operate the Optical Library using a host see your host software user manual For information on how to operate the Optical Library without a host see Operate Menu on page 60 CAUTION Do not operate the Optical Library while covers are removed Ambient light will interfere with Optical Library operation and moving parts increase risk of personal injury 143714 F DISCx000 Version 2 2User Manual Rev B 45 KAPITEL 5 ARBEITEN MIT DER OPTICAL LIBRARY HANDLING MEDIA HANDLING EKPOSED MEDIA Exposed media should be handled without touching the readable areas of the disc Scratches fing
18. ashes yellow then changes to green Optical Library scans the pack for media DISCx000 Version 2 2User Manual 49 KAPITEL 5 ARBEITEN MIT DER OPTICAL LIBRARY lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 50 KAPITEL 6 DIE BENUTZEROBERFLACHE CHAPTER 6 THE USER INTERFACE User Interface Diagram Activating the User Interface User Interface Modes and Commonly Used Functions 143714 F DISCx000 Version 2 2User Manual Rev B 51 KAPITEL 6 DIE BENUTZEROBERFLACHE lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 52 CC 9H jenueyy Jes 1z z uoisJ9A 000X9SIA d viZevit Press ESC to leave lap D Ei gt g ej gt 2 D e S t 2 LL 2 E 8 e D 2 eo 5 dn 259 sseJg umop Jeu Seel lt lt JOV443LN H3Sf IHL 3HOV IHH38OH3ZLTN38 214 9 T3 LId VM KAPITEL 6 DIE BENUTZEROBERFLACHE ACTIVATING THE USER INTERFACE The Optical Library User Interface Function Menu is activated by pressing the F key To navigate horizontally through the User Interface press the and arrow keys To navigate vertically press Esc up and Enter down If you know the number of the desired function you can press F followed by the function number to go directly to that screen Function numbers are listed on the User Interface Diagram For
19. ask settings Subnet Mask Set Used to set the NAS Subnet Mask Factory default is 000 000 000 000 Gateway Addr Read Displays the current default Gateway settings Gateway Addr Set Used to set the default Gateway Address Factory default is 000 000 000 000 Access IP List Only used with eCabinet storage accessories Used to set IP addresses for eCabinets accessing the Optical Library The factory default for all addresses is 000 000 000 000 IP Settings Clear Resets all addresses to factory default of 000 000 000 000 DISCx000 Version 2 2User Manual 62 KAPITEL 6 DIE BENUTZEROBERFLACHE SERVICE MODE NOTE Unauthorized use of Service Mode functions may damage the Optical Library and void your warranty The Service Mode is activated by entering the Service PIN from the PIN Codes menu of the User Mode In the Service Mode all functions and submenus become available The functions available in the Service Mode should only be used by trained technicians To deactivate the Service PIN so that no code is required to access the Service Mode change the PIN to 0000 NOTE For more information about the Service Mode see the DISCx000 Service Manual 143714 F DISCx000 Version 2 2User Manual Rev B 63 KAPITEL 6 DIE BENUTZEROBERFLACHE 143714 F DISCx000 Version 2 2User Manual Rev B 64 ANHANG B BEHORDLICHE GENEHMIGUNGEN APPENDIX B AGEN
20. ble Drives controlled by the Optical Library firmware via the blue cable IDrive SCSI ID Rotary Switches on the drive interface board The DISC7000 U are by factory default equipped with 1 to 3 SCSI busses Depending upon the number and type of drives in the Optical Library up to 6 SCSI busses are possible CAUTION To ensure reliable data transfer only shielded high quality SCSI cables should be used For additional SCSI cable information see the SCSI 3 specification Max external cable length is 10 meters CAUTION Your Optical Library uses Low Voltage Differential LVD technology ensure that all cables and terminators support LVD CAUTION The Optical Library LVD busses are internally terminated and therefore do not support daisy chaining Never connect any additional external SCSI device additional to the same bus together with the Optical Library 143714 F Rev B DISCx000 Version 2 2User Manual 27 KAPITEL 3 UBERSICHT 143714 F Rev B LVD equipped DISCx000 9 9 ES 9 9 9 9 9 9 9 erial Number Plate RS232 ID and Mode Selector Switches Rotate to Select RS232 Interfaces Power Connector LVD SCSI Connector LVD equipped DISCx000 U 68 pin HD screw attachement Drive SCSI ID Switches DISCx000 Version 2 2User Manual 28 KAPITEL 4 SETUP CHAPTER 4 SETUP Checking the Delivery Removing the Trans
21. e If your host software requires a SCSI connection see Connecting the SCSI Interface on page 40 and disregard the remainder of this section All mechanical operations including loading and unloading media and importing and exporting media can be controlled via the RS232 interface By default the RS232 ID for the robotics is set to 00 This setting need only be changed when more than one Optical Library is connected to the serial bus 143714 F DISCx000 Version 2 2User Manual Rev B 37 KAPITEL 4 SETUP 1 Host Computer 2 RS232 cable in RS232 cable from host computer to Optical Library in 3 Daisy chain connection for additional Optical Libraryes Optical Library out from first unit to Optical Library in on next unit CONNECTING THE SCSI INTERFACE 143714 F Rev B CAUTION Shut down the Optical Library and host computer before connecting cables Depending upon host software used to control the Optical Library either the serial interface or SCSI interface must be connected to the host computer This section pertains to systems connected to the host via a SCSI interface If your host software requires a serial connection see Connecting the Serial Interface on page 39 and disregard the remainder of this section CAUTION LVD equipped Optical Libraryes are internally terminated and therefore do not support daisy chaining Max external cable length is 10m S
22. e Codes in the PIN Codes menu The availability of functions in the User Mode may vary when being controlled by a host application INFO MENU The Info Menu provides information about the Optical Library configuration and capacity The following information is available in the Info Menu 143714 F Rev B DISCx000 Version 2 2User Manual 55 KAPITEL 6 DIE BENUTZEROBERFLACHE Info Menu Sub Menu Available Information Element Config Optical Library Equipment Information Mailslot available yes no Position of drives in Optical Library Type of drives SCSI IDs of drives Storage Config Optical Library Capacity Information Number of media in Optical Library number of CDs DVDs Total number of slots in Optical Library Prod Data Optical Library Production Data Information Vendor ID Product ID Revision level Production date Part number Serial number FW firmware revision FW firmware date Mode Optical Library Robotics Mode Information RS232 or SCSI mode License Optical Library License Information License Level used Interface Board used License Key Unit data 143714 F DISCx000 Version 2 2User Manual Rev B 56 KAPITEL 6 DIE BENUTZEROBERFLACHE PIN CODES MENU The PIN Codes menu allows you to enter or change the Optical Library PIN Codes This is required in order to enter Admin or Service areas of the User Interface or if you w
23. e traitement de l information EN 50024 1998 A1 2001 EN 50024 1998 A1 2001 EN 50024 1998 A1 2001 St rfestigkeit von informationstechnischen Information technology equipment Appareils de traitements l information Einrichtungen Immunity Characteristics Limits and characteristiques d immunit limites et methods of measurement m thodes de mesure EN 61000 3 2 2000 EN 61000 3 2 2000 EN 61000 3 2 2000 EN 61000 3 3 1995 A1 2001 EN 61000 3 3 1995 A1 2001 EN 61000 3 3 1995 A1 2001 EN 60950 UL 1950 CUL C22 2No 950 EN 60950 UL 1950 CUL C22 2No 950 EN 60950 UL 1950 CUL C22 2No 950 Sicherheit von Einrichtungen der Safety of information technology S curit des mat riels de traitement de Informationstechnik equipment l information Das Qualit tssicherungssystem von DISC DISC quality assurance system assures La syst me d assurance de la qualit de garantiert die Konformitat compliance DISC garantit la conformit Hersteller Manufacturer Fabricant DISC GmbH DISC GmbH DISC GmbH Im Tiergarten 24 Im Tiergarten 24 Im Tiergarten 24 D 55411 Bingen am Rhein D 55411 Bingen am Rhein D 55411 Bingen am Rhein Ausstelldatum 02 06 2005 Date of issue of the declaration Date d tablissement 7e la declaration 02 06 2005 02 06 2005 the Soo W Beckmann H Schellong Managing Director Director Development 143714 F DISCx000 Version 2 2User Manual Rev B 68 ANHANG B BEHORDLIC
24. eclaration of Conformity 72 CE D claration de Conformit 72 Declaration of Conformity DISC7000 73 EG Konformitatserklarung 73 EC Declaration of Conformity 73 CE D claration de Conformit 73 Technical Data 75 Technical Specifications 773 DISC1000 77 DISC3000 77 DISC4000 77 DISC7000 77 Interfaces 77 143714 F DISCx000 Version 2 2User Manual Rev B 4 Operating Conditions 77 Power Supply 77 OEM Specifications 78 DISC1000 78 DISC3000 78 DISC4000 78 DISC7000 78 Robotics 78 Drives 78 Dimensions and Weight 78 Slot Upgrades 79 143714 F Rev B DISCx000 Version 2 2User Manual 5 CHAPTER 1 COPYRIGHTS TRADEMARKS AND CONTACT INFORMATION Notice of Copyright Disclaimer Trademarks Contacting DISC 143714 F DISCx000 Version 2 2User Manual Rev B 6 lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 7 NOTICE OF COPYRIGHT All rights reserved Copyright 2004 by DISC GmbH No part of this publication may be reproduced stored in a retrieval system or traDISCitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written consent of DISC GmbH Schultheiss Kollei StraBe 5 D 55411 Bingen Germany Disclaimer DISC GmbH DISC GmbH and all of its subsidiaries takes no responsibility and offers no warranty with respect to the adequacy of this documentation or the procedures which it describ
25. erprints or any other artifact on the disc reading surface may cause loss of data Best wear cotton gloves when handling the bare media and keep them only within a well suited case like a jewel case or the DISC Offline Packs NorE The PDD media are protected by a special hard coated surface You may clean them carefully using a soft damp cloth without cleaning agent HANDLING PACKS 143714 F Rev B Media trays within packs are secured by the casing and will not fall out as long as all trays are in the pack with or without media in all trays Packs with missing trays must be handled carefully The remaining trays are locked into the pack but the medium below the removed tray is exposed and may move or fall out v Removing Trays from a Pack 1 Press the red button at the left side of the Pack 2 Pull out the tray DISCx000 Version 2 2User Manual 46 KAPITEL 5 ARBEITEN MIT DER OPTICAL LIBRARY IMPORTING AND EXPORTING MEDIA Media is imported and exported in one of two ways Through the Mailslot Through Packs Which method you use will depend on the circumstance and whether or not you have a host controlling the Optical Library THE MAILSLOT 143714 F Rev B When using host software to control the Optical Library the mailslot will automatically open when an import or export command is sent from the host After importing or exporting a medium the host application usually closes the mailslot au
26. es for any particular purpose or with respect to its adequacy to produce any particular result In no event shall DISC GmbH its employees its contractors or the authors of this documentation be liable for special direct indirect or consequential damages losses costs charges claims demands or claim for lost profits fees or expenses of any nature or kind CHANGES The following paragraph does not apply where such provisions are inconsistent with local law Some states do not allow disclaimer of express or implied warranties in certain transactions Therefore this statement may not apply to you The material in this documentation is for information only and is subject to change without notice While reasonable efforts have been taken in the preparation of this manual to assure its accuracy DISC GmbH assumes no liability resulting from any errors or omissions in this manual or from the use of the information contained herein DISC GmbH reserves the right to make changes in the product design without reservation and without notification to its users 143714 F DISCx000 Version 2 2User Manual Rev B 8 TRADEMARKS USED IN THIS MANUAL DISC and the DISC logo are registered trademarks of DISC GmbH CONTACTING DISC INTERNATIONAL INTERNET www disc gmbh com MAILING ADDRESS DISC GmbH Schultheiss Kollei StraBe 5 55411 Bingen Germany SALES Phone 49 0 6721 964 0 Fax 49 0 6721 964 414 E Mail sales disc gmbh com
27. he laser beam does not represent any risk for the user CLASS 1 LASER PRODUCT Entsprechend IEC 825 This product complies with the DHHS Rules 21 CFR chapter 1 sub chapter J accession number 9520184 applicable at the date of manufacture CAUTION The drives become under Laser Class 2M and 3B radiation if they get opened This includes the risk of injury if you stare into the beam or expose something to the beam You must not remove and open an optical drive of this Optical Library DATA SECURITY Access to media packs and magazines is available only when a release command is sent for the host It is your responsibility to allow access to the host computer where the release command is initiated to authorized personnel only 143714 F DISCx000 Version 2 2User Manual Rev B 14 ELECTROMAGNETIC COMPATIBILITY For CE certification the DISCx000 Optical Library was tested with Adaptec 2940 3940 29160 39160 29320 and 39320 SCSI host adapters Use of SCSI host adapters other than those above particularly with DVD drives may cause your system to exceed acceptable electromagnetic emissions FUSES The DISCx000 Optical Library must only be connected to electrical circuits secured by a 16 A fuse For USA and Canada the DISCx000 Optical Library must only be connected to electrical circuits secured by a 20 A fuse There are several internal fuses which only may be accessed by certified service staff Please call y
28. ion on handling packs once they are removed from the Optical Library see Handling Packs on page 46 NOTE For safety reasons adjacent packs cannot be removed at the same time NOTE Magazines are fixed to the Optical Library and cannot be removed To remove media from magazines either move the media to a pack for removal or remove it using the mailslot DISCx000 Version 2 2User Manual 48 KAPITEL 5 ARBEITEN MIT DER OPTICAL LIBRARY Action Status Display Press the pack button The LED starts to flash yellow all media are returned to the pack LED flashes green the pack is now ready to be removed The display reads Please push pack lt number of pack being removed gt Push the front of the pack towards the Optical Library The pack releases from the Optical Library The LED is not lit The display reads Please remove pack lt number of pack being removed gt NOTE If the Optical Library is controlled by a host application direct pack access from the Optical Library front panel may be disabled visible at the status LED that turnes to amber in this case If your host software runs in this manner packs can only be released by the host computer INSERTING PACKS 143714 F Rev B Action Status Display LED is dark Push the pack into the Optical Library LED fl
29. ish to change the PIN for either Admin or Service UI functions To access Admin areas of the UI enter the Admin PIN and press Enter The default Admin PIN is 9999 To access Service areas of the UI enter the Service PIN and press Enter To change the Admin PIN enter the new Admin PIN and press Enter You must first enter the original Admin PIN before you are allowed to change to a new Admin PIN To change the Service PIN enter the new Service PIN and press Enter You must first enter the original Service PIN before you are allowed to change to a new Service PIN ADMIN MODE 143714 F Rev B The Admin Mode is activated by entering the Admin PIN from the PIN Codes menu of the User Mode In the Admin Mode the Operate and Settings menus become available All necessary settings for installing the Optical Library can be configured in this mode It is also possible to fully operate the Optical Library without using a host application in this mode The default Admin PIN is 9999 To deactivate the Admin PIN so no code is required to access the Admin Mode change the PIN to 0000 DISCx000 Version 2 2User Manual 57 KAPITEL 6 DIE BENUTZEROBERFLACHE OPERATE MENU The Operate menu offers several functions to control or operate the Optical Library without host software CAUTION Disconnect the Optical Library from the host before executing any Operate menu commands The Operate Menu has 3 sub menus Element a Pack
30. isplay provides information about Optical Library status during operation When the Optical Library is first powered on the firmware revision displays for 5 seconds DISC 4000 V4508 09 02 05 The LCD is also used to display and or edit values in the Service Mode as well as to display Event Codes in the Event Logging Mode 143714 F DISCx000 Version 2 2User Manual 25 KAPITEL 3 UBERSICHT DISCx000 REAR DISC3000 DISC1000 DISC4000 DISC7000 RS232 Interfaces RS232 ID and Mode Selector Switches Rotate to Select Power Connector Serial Number Plate Power SCSI Connectors Connector RS232 ID and Mode Select Switches Drive SCSI ID Switches Rotate to select RS 232 Interfaces Serial number plate SCSI Connectors The DISC1000 is by default equipped with 1 LVD SCSI bus The DISC3000 and DISC4000 are by default equipped with 1 or 2 LVD SCSI busses depending upon the number and type of drives in the Optical Library and their assignment up to 4 LVD busses are possible The SCSI busses are wide 16 bit U160 LVD SCSI type with internal temination The connectors are of screwable 68 pin HD female type 143714 F DISCx000 Version 2 2User Manual Rev B 26 KAPITEL 3 UBERSICHT DISCx000 Rear Side View behind the backplane Robotic Interface RS232 Interfaces RS232 ID and Mode Selector Switches Rotate to Select Redundant Power Connectors SCSI Connectors 68 Pin HD female screwa
31. ldatum 02 06 2005 Date of issue of the declaration Date d tablissement 7e la declaration 02 06 2005 02 06 2005 Juel Soo W Beckmann H Schellong Managing Director Director Development 143714 F DISCx000 Version 2 2User Manual Rev B 71 ANHANG B BEHORDLICHE GENEHMIGUNGEN 143714 F DISCx000 Version 2 2User Manual Rev B 72 ANHANG TECHNISCHE DATEN APPENDIK A TECHNICAL DATA Technical Specifications OEM Specifications Slot Upgrades 143714 F DISCx000 Version 2 2User Manual Rev B 73 ANHANG TECHNISCHE DATEN lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 74 ANHANG TECHNISCHE DATEN TECHNICAL SPECIFICATIONS DISC1000 DISC3000 DISC4000 DISC7000 Interfaces RS232 RS232 ID 0 0 0 0 Baud rate 9600 Baud 9600 Baud 9600 Baud 9600 Baud Number of start bits 1 1 1 1 Number of data bits 8 8 8 8 Number of stop bits 1 1 1 1 Parity check No parity No parity No parity No parity ID Range 0 15 0 15 0 15 0 15 U160 SCSI LVD SCSI Robotics ID 0 0 0 ID Range 1 2 1 7 1 7 1 7 8 15 optional 8 15 optional 8 15 optional Operating Conditions Ambient 10 37 C 10 C 37 C 10 C 37 10 C 37 C temperature 50 F 99 F 50 F 99 F 50 F 99 F 50 F 99 F Operating 50 F 91 4 F 50 F 91 4 F 50 F 91 4 F 50 F
32. le produit PDD Optical Library PDD Optical Library Optical Library PDD DISC 4000 DISC 4000 DISC 4000 mit den folgenden Normen bzw normativen is in compliance with the following est conforme aux normes ou autres Dokumenten Ubereinstimmt standards or other normative documents documents normatifs suivants EN 55022 1998 A1 2000 EN 55022 1998 A1 2000 EN 55022 1998 A1 2000 Grenzwerte und Messverfahren f r Limits and methods of radio interference Limites et m thodes de mesure des Funkst rungen von informationstechnischen characteristics of information technology charact ristiques de perturbation Einrichtungen equipment radio lectriques produites par les appareils de traitement de l information EN 50024 1998 A1 2001 EN 50024 1998 A1 2001 EN 50024 1998 A1 2001 St rfestigkeit von informationstechnischen Information technology equipment Appareils de traitements l information Einrichtungen Immunity Characteristics Limits and characteristiques d immunit limites et methods of measurement m thodes de mesure EN 61000 3 2 2000 EN 61000 3 2 2000 EN 61000 3 2 2000 EN 61000 3 3 1995 A1 2001 EN 61000 3 3 1995 A1 2001 EN 61000 3 3 1995 A1 2001 EN 60950 UL 1950 CUL C22 2No 950 EN 60950 UL 1950 CUL C22 2No 950 EN 60950 UL 1950 CUL C22 2No 950 Sicherheit von Einrichtungen der Safety of information technology S curit des mat riels de traitement de Informationstechnik equipment l information Da
33. ll have filled up the empty rear side drive bays with additional Magazines or Drives Front of Library Mail Slot Pack 15 slots Pack 15 slots Magazine 50 Slots Magazine 50 Slots Mail Slot Pack 15 slots Pack 15 slots Pack 15 slots Magazine 50 Slots Pack 15 slots Front of Library Magazine 50 Slots Magazine 50 Slots Drive or 15 Slots Drive or 15 Sots Drive or 15 Slots Drive or 15 Sots Drive or 15 Slots Drive or 15 Sots Lift Mechanism Fixed Number of Media Slots 145 2 4 96 Drives Variable Number of Media Slots 270 slots with 2 drives 210 slots with 6 drives The position numbers are counted from the bottom to the top DISCx000 Version 2 2User Manual 20 KAPITEL 3 UBERSICHT DISC4000 COMPONENTS 4 or 5 Magazines holding 50 media each 4 removable Packs holding 15 media each 1 Mailslot for importing and exporting media Up to 6 drives Up to 4 data interfaces 160 MB s LVD SCSI 1 robotic interface RS232 or LVD SCSI The DISC4000 with 260 slots can be upgraded to a DISC4000 with 400 slots or 340 slots and 6 Drives This Optical Libraryes have 5 Magazines rather than 4 and will have filled up the empty rear side drive bays with additional Magazines or Drives Mail Slot Mail Slo
34. m or simply enter the address of the next medium After you are finished importing and exporting media close the mailslot door by gently pushing it Load Drive F112 Used to move and load a medium to any drive Unload Elements F114 Used to return all media from drives and the mailslot to their home storage positions Enable Button F121 Used to release a pack when the pack buttons are disabled by a host application This command will override the host and Machine Default Disable Button F122 Used to disable a pack that has been released with the Enable function This will return control of the pack back to the host application 143714 F Rev B DISCx000 Version 2 2User Manual 59 KAPITEL 6 DIE BENUTZEROBERFLACHE Command Functionality Swap Media F123 Used to exchange the contents of a pack front of the Optical Library with the contents of a magazine rear of the Optical Library Parameters include source pack front or rear of Optical Library bay and the destination magazine front or rear of Optical Library bay number of first slot to use Pack to Mag F124 Used to move all media in packs front of Optical Library to magazines rear of Optical Library This is the fasted way to import large quantities of media to the Optical Library in parallel Mag to Pack F125 Used to move all media in magazines rear of Op
35. nzwerte und Messverfahren f r Limits and methods of radio interference Limites et m thodes de mesure des Funkst rungen von informationstechnischen characteristics of information technology charact ristiques de perturbation Einrichtungen equipment radio lectriques produites par les appareils de traitement de l information EN 55024 1998 A1 2001 EN 55024 1998 A1 2001 EN 55024 1998 A1 2001 St rfestigkeit von informationstechnischen Information technology equipment Appareils de traitements l information Einrichtungen Immunity Characteristics Limits and characteristiques d immunit limites et methods of measurement m thodes de mesure EN 61000 3 2 2000 EN 61000 3 2 2000 EN 61000 3 2 2000 EN 61000 3 3 1995 A1 2001 EN 61000 3 3 1995 A1 2001 EN 61000 3 3 1995 A1 2001 EN 60950 UL 1950 CUL C22 2No 950 EN 60950 UL 1950 CUL C22 2No 950 EN 60950 UL 1950 CUL C22 2No 950 Sicherheit von Einrichtungen der Safety of information technology S curit des mat riels de traitement de Informationstechnik equipment l information Das Qualit tssicherungssystem von DISC DISC quality assurance system assures La syst me d assurance de la qualit de garantiert die Konformitat compliance DISC garantit la conformit Hersteller Manufacturer Fabricant DISC GmbH DISC GmbH DISC GmbH Im Tiergarten 24 Im Tiergarten 24 Im Tiergarten 24 D 55411 Bingen am Rhein D 55411 Bingen am Rhein D 55411 Bingen am Rhein Ausstel
36. omy 50 Slots Drive or 15 Sots een Si Drive a 15 Sot S Magazine Decemy M Magazine Drive or 15 Sots DR re Drive or 15 Ste ___ Drive or 15 Sots Magazine Magazine 50 Slots Drive or omy 50 Slots Drive or 15 Magazine Drive or emm Magazine Drive or 15 Sots EE Paid Diana Magazine Magazine 50 Slots Drive or omy 50 Slots Drive or 15 Sots Magazine Drive or emty Magazine Drive 15 Sots 50 Slots Drivecremy 50 Slots Disa i63 1 Lift Mechanism Lift Mechanism Fixed Number of Media Slots 510 Variable Number of Media Slots 2 4 6 8 10 12 or 14 Drives 690 slots with 2 drives 510 slots with 14 drives The position numbers are counted from the bottom to the top 143714 F DISCx000 Version 2 2User Manual Rev B 22 KAPITEL 3 UBERSICHT INSTALLED EQUIPMENT Refer to the serial number plate on your Optical Library for model and equipment information DISCX000 SN X01001 XX XXX XXXV xx xxHz TYPE BD 105 2 MANUFACTURED Made in Germany archive Disc GmbH Im Tiergarten 24 A CLASS 1 mE LASER PRODUCT Ds E EA TO IEC 825 1 1993 LISTED D 55411 Bingen am Rhein Cc es FE This product complies with DHHS Rules 21 CFR chapter 1 subchapter J This device complies with Part 15 of the F CC Rules Operation is subjectto the following two co nditions 1 This de vice maynot causeh armfulinte rference and 2 this devicemust accept any in
37. our dealer in case of service needs Fuse PCB Silkscreen Overlay Top Side Mount Fuse 5A 63V fast acting 142959 F 511 Sl2 Mount Fuse 2A 63V fast acting 142959 F SI3 Mount Fuse 2A 125V slo blo 143612 E SH PROFESSIONAL DISC MEDIEN The bare PDD media surfaces are covered by a special hard coating technology Nevertheless they are sensitive to scratches and fingerprints Handle writable media with care Damaged media could result in loss of data All bare media shall be handled outsite of the Optical Library within a certain cover To export bare media best use the DISC Offline Packs removable front site 15 pcs media magazines NOTE For best performance DISC recommends that only DISC certified media be used DVD RAM and DVD R Media Recordable DVD media especially DVD RAM are very sensitive to scratches and fingerprints Please handle recordable DVD media with care damaged or polluted media might end in a loss of data 143714 F DISCx000 Version 2 2User Manual Rev B 15 lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 16 KAPITEL 3 UBERSICHT CHAPTER 3 OVERVIEW 143714 F Rev B DISCx000 Components Installed Equipment DISCx000 Front DISCx000 Rear DISCx000 Version 2 2User Manual 17 KAPITEL 3 UBERSICHT lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 18
38. portation Fixtures Mounting the Stands Placing the Optical Library Operation Modes oetting the Drive SCSI IDs Connecting to a Host Computer Connecting Line Voltage 143714 F DISCx000 Version 2 2User Manual Rev B 29 KAPITEL 4 SETUP lt THIS PAGE IS INTENTIONALLY BLANK gt 143714 F DISCx000 Version 2 2User Manual Rev B 30 KAPITEL 4 SETUP CHECKING THE DELIVERY 143714 F Rev B Review the following table to ensure that you have all the required equipment Equipment Quantity Power Cord 4 Power Cord USA only USA 4 Ferrite 1 2 by dual redundant power supply unit RS232 Cable 4 Quick Installation Guide 4 User Manual CD 4 Allen type screw driver 4 Allen Type screws 4 6 missing screws to fully fix the right side cover Stands 4 only by DISC3 7000 Optical Library 4 DISCx000 Version 2 2User Manual 31 KAPITEL 4 SETUP REMOVING THE TRANSPORTATION FIXTURES NOTE More detailed information about removing transportation fixtures can be found on the label affixed to the Optical Library v Removing the Transportation Fixtures DISC3 7000 1 Remove the two screws that affix the right cabinet cover of the Optical Library 2 Remove the right cabinet cover 3 Remove the transportation fixtures inside the Optical Library v Removing the Transportation Fixtures DISC100
39. s Qualit tssicherungssystem von DISC DISC quality assurance system assures La syst me d assurance de la qualit de garantiert die Konformitat compliance DISC garantit la conformit Hersteller Manufacturer Fabricant DISC GmbH DISC GmbH DISC GmbH Im Tiergarten 24 Im Tiergarten 24 Im Tiergarten 24 D 55411 Bingen am Rhein D 55411 Bingen am Rhein D 55411 Bingen am Rhein Ausstelldatum 02 06 2005 Date of issue of the declaration Date d tablissement 7e la declaration 02 06 2005 02 06 2005 Wid Lew W Beckmann H Schellong Managing Director Director Development 143714 F DISCx000 Version 2 2User Manual Rev B 70 ANHANG B BEHORDLICHE GENEHMIGUNGEN DECLARATION OF CONFORMITY DISC 7000 EG Konformitatserklarung EC Declaration of Conformity CE D claration de Conformit mit den Richtlinien 89 336 EWG und 73 per 89 336 EEC and 73 23 EWG avec 89 336 CEE et 73 23 EWG 23 EWG Hiermit wird bestatigt dass das Produkt This is to confirm that the product Nous d clarons que le produit PDD Optical Library PDD Optical Library Optical Library PDD DISC 7000 DISC 7000 DISC 7000 mit den folgenden Normen bzw normativen is in compliance with the following est conforme aux normes ou autres Dokumenten Ubereinstimmt standards or other normative documents documents normatifs suivants EN 55022 1998 A1 2000 EN 55022 1998 A1 2000 EN 55022 1998 A1 2000 Gre
40. t Magazine Pack 15 slots TE ESS 50 Slots Pack 15 slots Pack 15 slots Pack 15 slots Pack 15 slots Drive or 15 Sots 8 Magazine Magazine Drive or 15 Sots 3 50 Slots 5 50 Slots Drive or 15 Sots 5 e Drive or 15 Sots Magazine Magazine 50 Slots 50 Slots Drive or 15 Sots Lift Mechanism Lift Mechanism Fixed Number of Media Slots 260 Variable Number of Media Slots 2 4 6 Drives 400 slots with 2 drives 340 slots with 6 drives The position numbers are counted from the bottom to the top 143714 F DISCx000 Version 2 2User Manual Rev B 21 KAPITEL 3 UBERSICHT DISC7000U COMPONENTS 9 Magazines holding 50 media each 4 removable Packs holding 15 media each 1 Mailslot for importing and exporting media Up to 14 drives Up to 6 data interfaces 160 MB s LVD SCSI 1 robotic interface RS232 or LVD SCSI The DISC7000 with 510 slots can be upgraded to a DISC7000 with 690 slots or 510 slots and 14 Drives This Optical Libraryes will have filled up the empty rear side drive bays with additional Magazines or Drives MailSlot m Mail Slot Magazine Magazine Pack 15 slots 50 Slots WE LS 50 Slots Pack 15 slots Magazine Pack 15 slots Magazine e 50 Slots 50 Slots Pack 15 slots Pack 15 slots Pack 15 slots Magazine _ 15 505 Magazine 50 Slots mu 50 Slots E Magazine 3 Magazine 3 50 Slots Driver
41. terference received including interf erence that may cause undersired operation Ce appareil num rique de laclass B res pecte toutes les exigences du R glem ent sur le mat riel brouilleurdu Canada This Class digitalapparatus meets all requirements of the anadien Interference Causing Equipment Regulations STRUCTURE OF MODEL DESIGNATION 143714 F Rev B DISCx000 T XXX YY R b DISCx000 Model T Technology type XXX Number of existing media slots YY Number of built in drives R Redundant PSU bei DISC1000 nicht verf gbar DISC3000 und DISC4000 optional DISC7000 Standart b Options DISCx000 Version 2 2User Manual 23 KAPITEL 3 UBERSICHT EXAMPLE OF MODEL DESIGNATION DISC3000 BD 225 4 R BD BD drives 225 225 trays 4 4 BD drives R Redundant power supply unit DISCx000 FRONT in LCD display Keyboard Power switch WPS Ja 8 Pack for multiple 143714 F Rev B LCD Keyboard Power Switch Mailslot Packs Mailslot for importing and exporting media import or export of 15 media DISCx000 Version 2 2User Manual 24 KAPITEL 3 UBERSICHT KEYBOARD The keyboard is used to operate the Optical Library without the aid of any external host software for Optical Library control The keyboard is also used to activate service and event logging functions Rev B LCD The Liquid Crystal D
42. the Service Mode Machine Default menu F31 in the User Interface CAUTION All software that wants to operate the Optical Library in SCSI mode requires the Machine Defaults to be set to 21 factory default before the installation NOTE In some Machine Defaults the packs can only be controlled by the host application AUTO Disc The Auto Disc function F36 is used to automatically load a specific disc into a drive when the Optical Library is powered up One use of Auto Disc is to start the complete system from a bootable disc Parameters for Auto Disc include the position of the drive bay to load to and the address of the medium front or rear of Optical Library bay number tray number to be loaded into the drive AUTO START The Auto Start function F37 is used to automatically mount media that are inside drives when the Optical Library is powered up TCP IP FOR USE AT EMBEDDED NAS MACHINES ONLY The TCP IP function is used to preset the static IP address and configure network parameters if the Optical Library is equipped with an internal NAS server unit 143714 F DISCx000 Version 2 2User Manual Rev B 61 KAPITEL 6 DIE BENUTZEROBERFLACHE 143714 F Rev B Parameter Function IP Address Read Displays the current IP Address settings IP Address Set Used to set the NAS IP Address Factory default is 000 000 000 000 Subnet Mask Read Displays the current Subnet M
43. tical Library to packs front of Optical Library This is the fasted way to export large quantities of media from the Optical Library in parallel The operation stops when all trays in packs are full and continues as soon as an empty pack is inserted Import Medium F131 Used to import several media serially into the Optical Library After import of the first medium close the mailslot with the Enter key The next empty tray is automatically loaded to the mailslot for the next import After you have imported the final medium press the Esc key to stop the operation Export Medium F132 Used to export several or all media Opposite of Import Medium F131 Swap Medium F133 Used to move a single medium to another storage location Parameters include source tray front or rear of Optical Library bay of magazine position of tray inside magazine and destination tray front or rear of Optical Library bay of magazine position of tray inside magazine 143714 F Rev B DISCx000 Version 2 2User Manual 60 KAPITEL 6 DIE BENUTZEROBERFLACHE SETTINGS MENU MACHINE DEFAULTS The Machine Defaults are special presets that can be used by a host application to configure the Optical Library All Optical Libraryes are originally set to Machine Default 21 A host application may change the Machine Default to another value It is also possible to manually change the Machine Default using
44. to the slot near the bottom of the Optical Library until it clicks in 6 Push the rear stand for the left side into the slot near the bottom of the Optical Library until it clicks in NOTE The roles of a DISC7000 have to stand to the outside Take care to mount the stands angled to the right side 143714 F DISCx000 Version 2 2User Manual Rev B 33 KAPITEL 4 SETUP PLACING THE OPTICAL LIBRARY 4 The DISCx000 Optical Libraryes are intended for use in office or computer lab environments CAUTION After delivery the Optical Library should be allowed to come to room temperature before operation When placing the Optical Library Avoid places with a extreme temperature excessive sun exposure high humidity Contact with water ontact with chemicals extreme vibration The right location has Stable even support Sufficient space to pull out and service the unit a ambient maximum of 37 C CAUTION To ensure sufficient cooling airflow and to have enough work space to exchange the air filter at least 50 cm free space has to be left at the right side of the Optical Library 143714 F Rev B DISCx000 Version 2 2User Manual 34 KAPITEL 4 SETUP OPERATION MODES Several operation modes are available which can be selected using the Mode Select switch on the rear of the Optical Library The function of the ID Switch depends upon the mode selected Which mode m
45. tomatically as well If your host does not automatically close the mailslot drawer you can close it by pressing the Enter key or gently pushing the front of the drawer For information on importing and exporting media without using a host application see Operate Menu on page 60 CAUTION Even if the bare PDD media are protected by a special hard coating you must not import media with polluted ore scrached surface into the library Avoid to touch the read write area of the media with your fingers Place exposed media immediately into a well suited case or cartridge DISCx000 Version 2 2User Manual 47 KAPITEL 5 ARBEITEN MIT DER OPTICAL LIBRARY USING PACKS DISC Media Packs are devices that contain 15 separate trays for media surrounded by a case You can quickly import or export multiple discs at once using packs that would otherwise take much longer to import or export through the Mailslot The Packs are also the best way to carry around or store the bare media Every Pack has a world wide unique serial number which is stored in a 512k Smart Card chip and labeled with barcode on the Pack case Therefore they easily can be handled and kept track by corresponding software applications REMOVING PACKS 143714 F Rev B Packs can be removed when the status indicator is green or yellow Packs are hot swappable meaning that the packs can be removed or inserted while the machine is in operation For more informat
46. ust be selected depends upon the host application used to control the Optical Library T RS 232 ye al oust Mode H Mode Function Function of ID Switch 0 0 RS232 mode RS232 ID robotik 1 SCSI mode SCSI ID robotik 2 F DISC internal use only RS232 MODE 143714 F Rev B The RS232 mode must be selected if the Optical Library is controlled via the serial interface RS232 The factory default RS232 ID is 00 The available range for the RS232 ID is 00 to 15 and can be changed using a small flat head screwdriver The ID need only be changed when more than one Optical Library is connected to the serial bus CAUTION Do not connect more than 3 Optical Libraryes to the serial bus If more than 3 Optical Libraryes are connected to the serial bus signal attenuation will occur causing Optical Library malfunctions The maximum serial cable length of the serial bus is 15 meters and must not be exceeded DISCx000 Version 2 2User Manual 35 KAPITEL 4 SETUP SCSI MODE The SCSI mode must be selected if the Optical Library is controlled via the SCSI bus The ID switch is used to select the robotics SCSI ID The range for SCSI IDs is 00 to 07 SCSI CABLE REQUIREMENTS CAUTION To ensure reliable data transfer only shielded high quality SCSI cables should be used For additional SCSI cable information see the SCSI 3 specification Your Optical Library
47. verified under test conditions that include the use of shielded cables and connectors between system components It is important that you use shielded cables and connectors to reduce the possibility of causing interference to radios televisions and other electronic devices Should you have any problems contact your dealer DISCx000 Version 2 2User Manual 67 ANHANG B BEHORDLICHE GENEHMIGUNGEN DECLARATION OF CONFORMITY DISC 1000 EG Konformitatserklarung EC Declaration of Conformity CE D claration de Conformit mit den Richtlinien 89 336 EWG und 73 per 89 336 EEC and 73 23 EWG avec 89 336 CEE et 73 23 EWG 23 EWG Hiermit wird bestatigt dass das Produkt This is to confirm that the product Nous d clarons que le produit PDD Optical Library PDD Optical Library Optical Library PDD DISC 1000 DISC 1000 DISC 1000 mit den folgenden Normen bzw normativen is in compliance with the following est conforme aux normes ou autres Dokumenten Ubereinstimmt standards or other normative documents documents normatifs suivants EN 55022 1998 A1 2000 EN 55022 1998 A1 2000 EN 55022 1998 A1 2000 Grenzwerte und Messverfahren f r Limits and methods of radio interference Limites et m thodes de mesure des Funkst rungen von informationstechnischen characteristics of information technology charact ristiques de perturbation Einrichtungen equipment radio lectriques produites par les appareils d
48. x000 Version 2 2User Manual Rev B OEM specifications 77 opening the unit 15 operating the Optical Library 47 operation modes 36 overview 18 P packs handling 47 packs inserting 50 packs removing 49 packs using 49 powering on the Optical Library 46 R rear 27 27 removing packs 49 removing the transportation fixtures 33 repairs 14 RS232 mode 36 S safety 15 safety and notices 15 safety instructions 15 SCSI cable length 37 SCSI cable requirements 37 SCSI interface connecting 39 SCSI mode 37 serial interface connecting 38 service mode 64 setting drive SCSI IDs 37 setup 30 specifications 77 specifications OEM 77 specifications technical 76 stands 34 1 technical data 74 technical specifications 76 transportation fixtures 33 81 Index U use of interjective terms 14 user interface 54 using packs 49 143714 F DISCx000 Version 2 2User Manual Rev B 82
49. y approvals 68 71 B ban on arbitrary reversions and changes 15 C cable length 37 cable requirements 37 checking the delivery 32 components 20 21 22 23 connecting line voltage 40 connecting the SCSI interface 39 connecting the serial interface 38 connecting to a host computer 38 D data security 17 declaration of conformity DISC1000 70 declaration of conformity DISC3000 71 declaration of conformity DISC4000 72 declaration of conformity DISC7000 73 declaration FCC 69 drive SCSI IDs 37 DVD R media 16 DVD RAM media 16 E electromagnetic compatibility 16 equipment 23 exposed media handling 48 F FCC declaration 69 70 71 72 fire and shock hazard 15 front 25 fuses 15 77 79 Index 143714 F DISCx000 Version 2 2User Manual Rev B H handling exposed media 47 handling media 48 handling packs 48 host computer connecting to 38 importing and exporting media 48 inserting packs 49 installed equipment 24 intended use 14 J Optical Library placement 35 Optical Library operating 36 Optical Library powering on 46 K keyboard 26 L LCD 26 line voltage connecting 40 mailslot 48 media 17 media handling 47 media handling exposed 47 media importing and exporting 48 mode service 64 model designation 24 modes of operation 36 mounting the stands 34 N DISCx000 components 20 21 22 23 DISCx000 front 25 DISCx000 rear 27 28 80 Index 143714 F DISC

(DVD/BD) User Manual - DISC Archiving Systems

Contents

Download Pdf Manuals

Related Search

Related Contents