EC2 User Manual
Contents
1. 14 days of purchase After 14 days all defective malfunctioning NITECORE products will be repaired free of charge for a period of 18 months from the date of purchase After 18 months a limited warranty applies covering the cost of labor and maintenance but not the cost of accessories or replacement parts The warranty is nullified in all of the following situations 1 The product s is are broken down reconstructed and or modified by unauthorized parties 2 The product s is are damaged through improper use 3 The product s is are damaged by leakage of batteries For the latest information on NITECORE products and services please contact your national NITECORE distributor or visit our official website www NITECORE com ZSYSMAX ina J SYSMAX Industry Co Ltd TEL 86 20 83862000 FAX 86 20 83882723 E mail info nitecore com Web www NITECORE com Address Rm1407 08 Glorious Tower 850 East Dongfeng Road Guangzhou China 510600 Thanks for purchasing NITECORE2. 2 is compatible with two primary CR123 Lithium batteries and one 18650 rechargeable Li ion battery When installing battery EC2 s built in MCU will automatically detect the installed battery type and then Quality holster lanyard spare O ring Battery Options automatically select the best suited driving data and battery capacity detecting data SIZE Nominal voltage Compatible Primary Lithium battery CR123 3V Y Recommended WARNING Always ensure batteries are inserted with the positive ends pointing 18650 Rechargeable Li ion battery __ 18650 3 7V Y Recommended toward the flashlight head If incorrectly installed the flashlight will not Rechargeable Li ion battery RCR123 3 7V Y work Note When EC2 is driven by 2 RCR123 batteries the battery capacity indicator function Switch i ng ON OFF tb tivated lly E AAE gsm EE To switch ON Press the On OFF button once to turn the light on s To switch OFF Press the On OFF button once again to turn the light Brightness amp Runtime off FL1 STANDARD TURBO HIGH MID MICRO Note When EC2 is off the power indicator red light will flash once built in MCU and power indicator Under such status two CR123 batteries will last about 1 year in this mode LOW 2 every 3 seconds to act as a locator In this mode the EC2 consumes a LUMENS very little amount of current about 0 2mA to maintain working of the 150m Beam Distance Brightness Selection Wit
3. NITECORE EL 2 User Manual ALL ROUND Flashlight Expert Features Operation instructions CREE XP G R5 LED Battery installation Maximum output of up to 320 lumens 1 Unscrew counterclockwise and remove the tail cap High efficiency constant current circuit enables maximum run time of up to 2 Insert two CR123 batteries or one 18650 battery with the positive 220 hours poles of the batteries pointing toward the head 5 brightness levels p 3 Replace the tail cap and fasten tightly Momentary push on strobe and SOS modes Dual electronic switches ensure very easy user interface Secondary red light mode 0 2 lumens e Power indicator light also serves as a battery voltage indicator accurate to 0 1V e Power indicator light serves as standby indicator light when powered down e Broad voltage circuit accepts both rechargeable and non rechargeable lithium batteries Toughened ultra clear mineral glass with dual side anti reflective coating Elaborate alloy reflector is purpose designed for exceptionally long throw Constructed from aero grade aluminum alloy HAIII military grade hard anodized e Stainless steel bezel retaining ring protects core components from damage e Detachable two way anti rolling clip e Waterproof in accordance with IPX 8 2 meters submersible e Tail stand function Dimensions Length 99mm Head Diameter 25 4mm Tail Diameter 24mm Weight 59g without battery Accessories Note EC
4. h the flashlight switched on each time you press the MODE button 5650cd Peak Beam Intensity it will go through the different preset brightness levels as follows ultra low mode low mode medium mode high mode then repeat Under this mode the flashlight has a memory function It can memorize the selected brightness after turning the light off while next time turning on the light it automatically resumes to the previously selected mode 1 5mM Impact Resistant IPX 8 2m Waterproof AND Submersible Entering Turbo Mode NOTICE j 7 y The stated data has been measured in accordance with the international 2 Hee illo ahs Hek for nee pa 1 flashlight testing standards ANSI NEMA FL1 using two SYSMAX CR123 econd EC2 will enter Turbo mode Press the utton again the flashlight will retreat from turbo brightness and resume to previous brightness In Turbo mode EC2 circuit will deliver maximum current to make brightness as high as possible battery 3V 1550mAH under laboratory conditions The data may vary in real world use due to different battery usage or environmental conditions Thanks for purchasing NITECORE NITECORE ALL ROUND Flashlight Expert Note 1 After 30 minutes working in Turbo mode the flashlight will automatically restore to the previously selected brightness level to safeguard against overheating 2 While activating Turbo mode the brightness level increases about 100 lumens Due to adaptabil
5. ity of human eyes this brightness increase may not be apparent within close range observation In real world usage Turbo mode can help EC2 throw to a longer range Entering Strobe and SOS Mode With the light switched off press the ON OFF button for more than 1 second to enter Strobe mode In strobe mode press any button ON OFF or MODE to exit strobe and switch the light off With the light switched off press the ON OFF button for more than 1 second to enter SOS mode In SOS mode press any button ON OFF or MODE to switch off the light and quit SOS mode Red Light Mode With the light switched off press the MODE button to enter red light mode In this mode the power indicator will continuously emit red light 0 2 lumens Press the MODE button once again to quit the red light mode Lockout Mode With the light switched on press the ON OFF button for over 1 second to enter lockout mode In lockout mode EC2 power source system will shut down most of the circuit components to reduce its power consumption The MCU only consumes small amount of power to maintain its work The red light indicator also switches off to save energy Under this mode the maximum consuming current is about 0 1mA which ensures two CR123 batteries can maintain its work for around 2 years In lockout mode the 2 buttons on EC2 will not work which can prevent the light from being turned on accidentally To exit lockout mode simply p
6. ress the ON OFF button for more than 1 second Note When entering lockout mode the red light indicator light will continuously flash to advise of battery voltage Please refer to the Power Indication section below Power Indication With the light switched on and when the battery power has been consumed by about 50 the power indicator light on the control panel will flash once every 6 seconds as a reminder of battery capacity When the battery power is almost depleted the power indicator light will flash 3 times every 3 seconds to indicate low battery capacity When entering lockout mode the power indicator will automatically detect and notify you of battery voltage accurate to 0 1V with a series of flashes For example if the battery voltage is 4 2V the indicator will flash 4 times followed by a one second pause and then another 2 flashes Battery replacement If battery level is low the red power indicator light will flash three times every 3 seconds If the power level is critically low the light will become very dim and unresponsive to brightness adjustment A replacement battery is required at this time Maintenance Every 6 months the threads should be wiped with a clean cloth followed by a thin coating of silicon based lubricant Warranty Service All NITECORE products are warranted for quality DOA defective products can be exchanged for replacement though a local distributor dealer within the
Download Pdf Manuals
Related Search