Elite Weathermaster 6 Screened Tent 2000001588
Contents
1. STITCH LINE Before you begin Read all instructions before set up e Select a level site clear of rocks branches and other hard or sharp objects to install your tent WARNING Keep clear of overhead power lines e Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather e Secure with all stakes and guylines provided to prevent property damage or personal injury e For best results in windy conditions position narrow end of tent into the wind e Enlist the help of at least one other person to assist you when it is time to assemble the tent Pole Descriptions Pole Pole Pole Description Qty Dia Repair Kit Replacement Kit Long Leg Pole steel w red marking 4 19mm N A 9010000608 Short Leg Pole steel 4 19mm N A 5010000610 Curved Ridge Pole steel w red marking 2 19mm N A 5010000607 Curved Ridge Pole steel 2 19mm N A 5010000609 Awning Pole black fiberglass metal tips 1 63mm 5010000543 5010000545 Door Pole long thin black fiberglass rubber tips 1 63mm 5010000543 5010000545 7 Vert Door Pole short black fiberglass rubber tips 1 63mm 5010000543 5010000545 Self Rolling Window Spring Descriptions Color Code Description Qty Length Replacement Part No Red 1 360mm 5010000624 8 Green 3 610mm 5010000627 Orange 2 670mm 5010000628 CAUTION Springs may have sharp edges Handle with care to avoid injury Keep out of reach of children H uon Up Ten2. ccess to Fig 19 your beverage cooler 4 Go to opposite center Leg Pole on 1 To use as a vent unzip flap to expose screen other side of door and gradually 2 To use as a cooler access unzip other flap to apply pressure to the pole forming make an avenue to bring beverages into tent an arch Insert metal tip into the Fig 32 grommet 5 Locate all hook amp loop fasteners on underside of Rainfly and wrap around Leg Poles and To Store Awning Pole locations Fig 20 1 All springs must be rolled up and placed in bag with stakes 2 All poles and stakes must be placed in the storage bag to prevent damage to the fabric items placed in the carry case 6 Insert metal hook on Center 3 Make sure tent is clean and dry before placing in carry case elastic straps on ee 4 Remove rainfly spread out on floor of tent then unzip door amp vents Rainfly into the hole before taking tent down for storage on each Leg Pole 5 Neatly fold tent to width of pole storage bag place on tent roll Fig 21 amp 22 tightly and place in carry case 5 Store in a clean dry area 7 Loop ends of guylines over stakes stretch tight then hammer into LESIN at an angle as shown Fig 23 amp 23A Things You Should Know e Under certain conditions cold weather high humidity etc condensa tion will form on the inside of your tent Condensation is caused by water vapor from your breath perspiration or any wet clothin
3. g inside the tent It is NOT LEAKAGE through the tent fabric It can be minimized by removing wet clothing from your tent and by providing good ventila tion through the tent Tree limbs tree sap bird droppings or moisture steadily dripping off tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of flame resistant properties Never store tent even for a short period of time without drying it thoroughly and brushing off caked dirt Do not pack stakes or poles inside your tent Use a separate storage bag Stakes should be removed by pulling on the stake itself NEVER PULL ON THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY Tent poles should not be left telescoped together during storage Do not leave your tent set up for weeks at a time Be aware that exposure to ultraviolet rays from the sun can seriously damage material and or cause it to become discolored AX WARNING Keep all flame and heat sources away from this tent fabric This tent meets the flammability requirements of CPAI 84 The fabric may burn if left in continuous contact with any flame source The application of any foreign substance to the tent fabric may render the flame resistant properties ineffective Self rolling Windows CAUTION Springs may have sharp edges Handle with care to avoid injury Keep out of reach of children NOTE Carefully unroll metal springs stored in bag wit
4. h Fig 8 To stretch tent to finished size e Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise Fig 9 e Pull up on top Leg Pole section until tent is taut e Twist the lower Leg Pole clockwise until the button locks into the center or lowest hole e Repeat on remaining Leg Poles Upper Leg Pole Section Button Center Hole Lower Hole Lower Leg Pole Section Insert plastic stakes through web straps located on both sides of tent then drive in to secure Fig 10 NOTE It may be necessary to remove metal Stakes through web straps at side of tent and Screen room pull tent taut and drive in stakes to secure Hinged Rigid Door Assemble Vertical Door Pole shorter black pole with plastic tips then insert through zippered vertical pole sleeve on hinged side of door Fig 11 Insert end of Vertical Door Pole into bottom hinge plate apply pressure to form a slight bow then insert other tip of pole into top hinge Zip up vertical pole sleeve Fig 12 amp 13 Assemble Door Pole longer black pole with plastic cap tips then insert into zippered pole sleeve at top of door Fig 14 Insert end of Door Pole into top hinge plate apply pressure to form a bow then insert other tip of pole into the bottom hinge Fig 15 Zip up pole sleeve to enclose Door Pole Fig 16 Fig X E Pole Sleeve 0 continued on other side Tent Lighting System Your tent comes
5. h stakes The color marking on each spring should match the color of the fabric flag sewn to the window or door sleeve opening Fig 24 1 Locate sleeve s in window panel open hook amp la loop fastener then insert spring s with match ing color marking Fig 24 amp 25 NOTE When inserting into the sleeve s the color marking on the spring s should always face the operator Close hook amp loop fastener to secure Before unzipping and opening the window push in at top to engage spring s to activate the self rolling feature Fig 26 4 Unzip to allow the window panel to roll down automatically zip back to close window panel Fig 27 amp 28 NOTE Repeat steps above for inserting the color matching spring s into sleeve s for the rest of the windows Go N e 3600 N Hydraulic Wichita Kansas 67219 1 800 835 3278 www coleman com The Coleman Company Inc SS MADE IN CHINA PRINTED IN CHINA 2008 The Coleman Company Inc Coleman j and Weathermaster are registered trademarks of The Coleman Company Inc 4010003995 20081030
6. pre wired with the Coleman Tent Lighting Self rolling Windows continued CAUTION All springs must be removed from sleeves before tearing down tent to avoid damage to the tent fabric or part To avoid injury carefully roll up springs Keep out of reach of children Store rolled System See manual that came with the light and carefully read all instructions before use then save for future reference To Attach Rainfly 1 Drape Rainfly over tent Make sure seams on Rainfly are facing down and centered over poles of the tent Fig 17 NOTE Hook and loop fasteners located on seams of underside of Rainfly should be centered over Ridge Poles Rainfly springs in bag with stakes Attaching Room Divider 1 seemed Cord Access Divider Panel can be installed through center of the tent by inserting the toggles through top and bottom fabric loops as shown Fig 29 amp 30 Unzip the access panel in the lower left corner of tent and bring in an ANI HOLILS 2 Assemble thin black shock corded electrical cord Awning Pole with metal tips then NOTE Use only UL approved cords insert through sleeve in Rainfly above rated for outdoor usage Fig 31 door Fig 18 3 Insert tapered metal tip on Awning Cooler Access Pole into grommet located on web The smaller zippered opening at the side of tent is strap clipped to center Leg Pole designed for added ventilation and easy a
7. t Unfold tent and spread out on a clean level surface with the door facing the desired direction Unzip doors Fig 1 9 2 Pull four corners of tent taut then secure by driving stakes through web loops at an angle for better anchoring Fig 2 3 Assemble four steel shock corded curved Ridge Poles Insert Ridge Poles with red Ridge Pole 2 marking into center sleeves on top of tent with Red FO with the red trim Fig 3 Insert the remain Marking Eg ing curved Ridge Poles into the other two 3 sleeves on top of tent 4 5 4 Assemble eight steel shock corded Leg Poles Push down on steel button on tapered end and insert into end with four holes NOTE Make sure steel button locks into third hole on pole as shown Fig 4 5 Insert curved end of Leg Poles with red marking into the ends of the Ridge Pole with red marking Insert curved end of remaining Short Leg Poles into the ends of the remaining ae _ gt Ridge Poles Fig 5 amp 6 f Curved End of z Long aa aka i af e 3 i Ridge Pole with lt Red Marking Sleeve H with Red Trim A ELITE WEATHERMASTER 6 SCREENED TENT MODEL 2000001588 Curved Ridge Poles with Red Markings in center sleeves Rotate all eight Leg Poles upright and insert pin on each web loop at the side locations as shown Fig 7 amp 7A Locaie the plastic hooks at sides and corners of tent then snap onto Leg Poles to attac
Download Pdf Manuals
Related Search