Electrician Installation Manual National Warranty Line
Contents
1. attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan INTERNATIONAL Installation Instructions Attaching an accessory light kit STEP 3 Fig 12 a Once globe is placed into its socket properly the glass cover can be fitted on to the fan b Gently push the glass cover upwards and turn it clockwise The tabs should lock in to place ensuring the glass cover is securely attached to the motor housing te Glass Cover Trouble Shooting Tips Light WARNING Light will not turn on Make sure globe has not blown and it is properly fitted between the metal prongs Check all light wires in the light kit the terminal block in the canopy cover and the wall switch has been connected together correctly Light is not corresponding to remote control Make sure globe has not blown and it is properly fitted between the metal prongs Check all light wires in the light kit the terminal block in the canopy cover and the wall switch has been connected together correctly Check dip switch settings in remote hand pi2. is not going to be used Wiring Instructions with and without accessory light APY E N A Green yellow Separate Control Control White or Red Green yellow FA LAE N ee paat i i Wiring for use with 3 pole block a ie aa eau i varati e only Block is fitted Separate extension terminal for active for light when 3 pole block fitted 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan STEP 5 Fig 6 a Slide canopy cover up and over the hanger bracket b Twist the canopy to locate screws holes then tighten canopy screws half way c Now twist the canopy cover in the opposite direction and fully tighten screws until the canopy cover is stabilized Canopy Cover Down Rod STEP 6 Fig 7 n a Remove the base plate you can do this ig Motor Housing by spreading out your fingers and pressing your hand against the base plate Push upwards and turn anticlockwise until the t
3. press against the plate and stop the fan from working If it is a Typhoon fan check the nine pin plug under the switch cover is properly connected and the colours on the plug are corresponding If it is a Concept fan and it has an external start up capacitor check that this external capacitor is properly connected Fan speed is not corresponding to the wall controller Check the speeds on the wall controller has been wired correctly and are making proper contact Brown speed 1 Purple speed 2 Red speed 3 Check wires in the terminal block are connected properly connection wires should be stripped back at the connection point and unused wires should be sealed and capped off Check that the reversing switch is pushed into its Summer or Winter position Fan is not corresponding to the remote control Check for flat battery Make sure the dipswitch settings in the hand piece and the remote receiver for the same fan are corresponding Fan is wobbling Check the ball joint slot is locked into the hanger bracket groove Make sure blades are a matching set the letters on matching sets of blades should be identical with the numbers varying within 3 grams of each other Check blade screws are tightened firmly If necessary use balancing kit provided to settle the wobble Fan is noisy Check all screws and parts are secured firmly Ensure there are no loose parts moving inside the motor housing Make sure the fan is installed with a Hu
4. COLOUR CODE Brushed Aluminium 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan STEP 1 Fig 1 j lt Ball Joint PERFORM THIS STEP IF THE WIRES HAVE NOT Down Rod 11 BEEN FED THROUGH THE DOWN ROD q Canopy Cover a Loosen the ball joint screw and remove the ball joint pin to separate the down rod from the ball joint Connection Collar b Feed wires from motor housing up and I A through the down rod r eS agi c Insert the down rod pin screw through the OY connection collar and the down rod avoid a J Motor Housing pinching wires Tighten down rod pin screw oS ak Secure down rod with the other shorter down N rod screw provided Am d Slide on canopy cover and refit the ball joint _4 Down Rod Pin Screw Fig 1 If an extension rod needs to be installed please go to page 11 STEP 2 Fig 2 a Drill a hole in the timber nogging for wiring Hanger b Secure the hanger br
5. Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC INTERNATIONAL eon FAT NOTE The Icon light fitting does not come standard however it can be bought as an accessory item CEILING FAN MUST BE INSTALLED BY A LICENSED ELECTRICIAN NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN After installation electricians must tick off all items on the quick checklist and fill out their details onto the back page of the Fan Owner Warranty amp Operations Manual ELECTRICIANS TO PROTECT YOUR CUSTOMER S WARRANTY PLEASE READ PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Hunter Pacific International Pty Ltd Building 8 256 New Line Road Dural NSW 2158 Australia ABN 18 063 521 666 l Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC N TERNATIONAL IMPORTANT INFORMATION ELECTRICIANS MUST READ PRIOR TO INSTALLATION Distributor and installer details and purchase receipts are essential for on site warranty claims and must be presented to repair personnel make sure you record your details in the Fan Owner Warranty and Operations Manual Fans and fixed wiring products must only be installed by persons who are appropriately licensed by the applicable State regulatory body Therefore to protect our repair personnel on site war
6. abs unlock b Once the base plate is removed the internal blade carriers will be exposed Insert blades and attach them to the motor housing as shown in figure 8 c Tighten the 3 blade screws firmly but do not over tighten d Install blades for each fan individually do not mix blades from different fans as this will up set the balance of the fan Base Plate 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan STEP 7 Fig 8 a Once all blades are attached to the motor housing refit the base plate by gently pushing it upwards and turning it clockwise The tabs should lock in to place ensuring the base plate is securely attached to the motor housing Base Plate STEP 8 Fig 9 a Reverse switch should be in the down Reverse position for Summer fan spins anticlockwise and in the up position for Winter fan spins clockwise b Make the sure reverse switch is not stuck in its neutral position
7. acket onto the timber Timber Nogging ec nogging using the two hex head screws provided The timber nogging should be supplied by the installing electrician and must be supported between the two ceiling joists as shown in the diagram above Hex Head Screw STEP 3 Fig 3 a Hang the ball joint into the hanger bracket Ensure the groove on the hanger bracket is locked into the slot on the ball joint This is important to ensure the fan will not Down Rod wobble and the weight of the fan is supported 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan STEP 4 Fig 4 amp 5 a Connect wires from the fan with wires in the ceiling via the terminal block on the hanger bracket refer to figure 4 and 5 Earth Wires Red White b Make sure earth wires are also connected A3 E c Connect light wires red white if a light Earth Wires fitting is going to be used Cap seal light i wires if a light fitting
8. an light are run from the same final circuit Mounting bracket must be firmly secured to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for certain types of installation Fan blades are at least 2 1m 7feet above floor level Check the fan is operating correctly on all three speeds using the wall controller If light is installed Check light switch is functioning properly If remote control is installed Check the fan and light if installed is responding to the remote control correctly If remote control is installed Check where possible a separate isolation switch has been installed for the fan Check electrician s details have been recorded onto the back page of the Owner s Operations and Warranty Manual 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 13
9. ece and remote receiver are corresponding Light wires appear to be missing or too short Wires may be stuck in the motor housing Carefully pull wires out of the motor housing careful not to strip the wires as this may cause the fan to short Light flickers or flashes Check globe is secured between the metal prongs in the light kit Make sure you are using the globes specified 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 10 Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Attaching an extension rod Hunter Pacific rods to be used ONLY Ball Joint Pin Ball Joint Screw Down Rod Down Rod Step 2 Fig 14 Loosen the ball joint screw take out the ball joint pin and remove the ball joint Then slide off the Step 1 Fig 13 canopy cover Loosen and remove the down rod screws and the down rod pin screw to remove the standard down rod from the motor housing Tighten Ball Joint Screw Down Rod Step 3 Fig 15 amp 16 Now install the extension rod and rever
10. ing on the ceiling Special mounts such as T hooks are available for certain types of installation e After installation fan blades must be at least 2 1 m 7 feet above floor level f The use of these products by children and the infirm must be under supervision IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY HOT LINE NUMBER 1300 360 280 BEFORE LEAVING THE JOB SITE PLEASE DO NOT REMOVE THE FAN FROM THE CEILING ONCE INSTALLED UNLESS INSTRUCTED TO DO SO Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC INTERNATIONAL Parts List lcon Fan _ Hanger Bracket B Hex Head Screw Ball Joint _ Canopy Cover Motor Housing an Base Plate Blade Screw 2 i eres 2 Ball Joint Screw Down Rod Pin Screw Ball Joint Pin Down Rod Short Screw Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan HUNTER PACIFIC INTERNATIONAL IMPORTANT INFORMATION The table below contains information that can help you quickly identify the product you are installing If you have any difficulties installing our product we recommend you to call our warranty line on 1300 360 280 for advice Icon Ceiling Fans 132cm 52 FAN MODEL NAME COLOUR CODE Brushed Aluminium Motor The table below advises accessory items that can be purchased for the Icon fan Icon Lights Kits
11. nter Pacific wall controller only do not use solid state controllers as they can cause unpleasant motor noises National Warranty Line 1300 360 280 WARNING Monday to Friday from 9am to 5pm EST Only available within Australia Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 12 HUNTER PACIFIC Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan INTERNATIONAL Quick Checklist Electricians make sure everything on this checklist is ticked off before you leave the installation site If you have trouble installing our product please refer to the trouble shooting section on the previous page first then phone the Hunter Pacific Warranty Line on 1300 360 280 open 9am to 5pm EST DO NOT uninstall the fan and DO NOT return fan to retailer 10 WARNING Ceiling fan is not installed to a solid state wall controller Neither leading nor lagging edge controllers will give satisfactory performance Wall controllers must only be types approved for use by Hunter Pacific International The fan optional fan light and bracket is earthed Fan and optional f
12. otherwise the fan will not spin 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC INTERNATIONAL Light p a HA extremely important to keep the globe WARNING Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan Installation Instructions Attaching an accessory light kit STEP 1 Fig 10 a Remove the base plate you can do this by spreading out your fingers and pressing your hand against the base plate Push upwards and turn anticlockwise until the tabs unlock STEP 2 Fig 11 a Using the connectors on the wires connect the light wire from the motor housing with the light wires on the light assembly b Attach and secure the light assembly kit using the 3 screws provided c Plug the light globe into the socket DO NOT touch the light globe with your fingers use a tissue It is clean If the globe is dirty clean it carefully with a cloth or tissue Dirt on the globe will cause it to fail almost immediately NOTE Do not use globes other than the specified ones B Screws 1 Do not
13. ranty claims will not be accepted if products have been installed by unlicensed persons Damage caused by incorrect installation force majeure electrical surges lightning power grid fluctuations water or by connection to alternative power supply sources such as solar inverters etc is not eligible for warranty repair Blades must be replaced only as a complete set Blades are supplied only as a pre balanced set and the replacement of individual blades may void the warranty by causing mechanical damage to the motor excessive noise or premature wear When products are installed in a location requiring special access equipment such as scaffolding or scissor lifts etc the cost of providing installing and operating special access equipment must be borne by the site owner For safety and to protect your customers warranty the following must be taken into account when installing and operating the product s a DO NOT USE SOLID STATE WALL CONTROLLERS Neither leading nor lagging edge controllers will give satisfactory performance Wall controls must only be types approved for use by Hunter Pacific International b The fan light and bracket must be earthed c Fan and light must be run from the same final circuit d Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left float
14. se step 1 amp 2 to secure the rod to the fan and the ball joint Housing NOTE If the extension rod needs to be shortened cut the rod to the required length and drill the appropriate hole size to fit the ball joint pin The cut end of the rod should be used on the ball joint end only When installing a 1 8m extension rod the wiring will need to be extended and joined This should be done using crimp style connectors 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set 11 HUNTER PACIFIC Electrician Installation Manual Icon 52 inch 132cm Ceiling Fan INTERNATIONAL Trouble Shooting Tips Fan Fan will not start Check that the reversing switch is pushed into its Summer or Winter position Check wire connections in the wall switch and terminal blocks ensure all wires are making proper contact If it is a Typhoon fan check and ensure the reversing switch plate under the switch cover is not bent also check the 3 wires coming from the switch plate are straight Occasionally the switch plate may get bent during transportation this allows the switch cover to
Download Pdf Manuals
Related Search