User`s Manual
Contents
1. with three holes install the proper grounding adapter not supplied 31MY02 Envision Before You Operate the Monitor EN 985e Connecting the Wires Using An Optional Power Cord Not Supplied The power cord supplied with your monitor can Follow these steps only be connected to a grounded electrical wall 1 Connect the built in video cable into the 15 pin socket or power strip connector on the back of your computer and If you wish to connect your monitor to a power tighten the two screws supply using the power input socket on the back of 2 Connect the power cord into your monitor s your computer you must purchase a power cord power input socket with CEE 22 terminated connectors see illustration above 3 Plug the other end of the power cord into the power output socket on your PC EN 985e 7 31MY02 Envision Operating Instructions EN 985e Front Panel Buttons Contrast OSD Window 70 A A 29300 4 6500 a O O lt E gt O gi pi Power Button a Exit Power Indicator Brightness Menu Contrast O Exit Press this button to save changes and MENU Press this button to open the OSD ext Close the OSD window menu Window or select a highlighted function a Brightness Press this button to adjust the o Power Indicator A green light indicates picture s brightness If the OSD window is that the2. you may have other rights which may vary from state to state In the United States of America this limited warranty is only valid for products purchased in the Continental United States Alaska and Hawaii Outside the United States this limited warranty is only valid for products purchased in Canada In the United States to obtain service under this limited warranty 1 Call EPI s Customer Service RMA Department at the toll free number 888 838 6388 for the nearest Authorized Service Center located in your area 2 Ask for a Return Merchandise Authorization RMA number 3 Deliver the product freight pre paid to the EPI Authorized Service Center If you cannot deliver the product in person e Pack it in its original shipping container or equivalent e Put the RMA number on the shipping carton e Insure it or assume the risk of loss damage during shipment e Pay one way shipping charge EN 985e Warranty continued EN 985e EPI is not responsible for damage to inbound products that were not properly packaged EPI will pay the return shipment charges within one of the countries specified within this warranty statement EPI is not responsible for any costs associated with the transportation of products across international borders This includes the international borders of the countries within this warranty statements 2002 Envision Peripherals Inc 17 31MY02
3. the picture until the edges neither bulge out nor pull in Trapezoid Adjusts the top and bottom of the picture until the sides are parallel Pin Balance Adjusts to compensate for the pincushion unbalance Parallelogram Shifts the top and bottom of the picture left or right until the sides are vertical Rotation Rotates the entire picture Color Temp Adjusts the color temperature to 6500 K x 0 313 y 0 329 EN 985e O User Color Red Blue Adjusts the Red Blue Gain controls to obtain optimum whiteness level 9300 Color Temp Adjusts the color temperature to 9300 K x 0 283 y 0 297 Degauss Adjusts color impurity caused by monitor movement or magnetic field build up inside the monitor Moire Reduce Reduces interference that appears as ripples or wave patterns Recall Restores the monitor to factory settings Exit Saves changes and closes the OSD window 5 To save and exit press the EXIT icon or leave the monitor alone for 10 seconds If you want to adjust any other function repeat steps 2 4 Note When the OSD window is open the input signal timing settings appear at the top H stands for horizontal frequency and V stands for vertical frequency 31MY02 Env sion Plug 8 Play DDC1 2B Feature This monitor is eguipped with VESA DDC1 2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC
4. used communicate additional information about its display capabilities The communication channel is defined in two levels DDC1 and DDC2B The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information The DDC2B is a bidirectional data channel based on the I C protocol The host can request EDID information over the DDC2B EN 985e Operating Instructions EN 985e Windows INF Driver File Most computers will automatically configure your monitor to work with your computer For optimal viewing of your monitor download the Envision monitor driver Follow these steps 1 Go to www ENVISIONmonitor com 2 Click on SERVICES amp SUPPORT to open the drivers web page 3 Follow the directions on the web page to download and install the driver on your computer Or go to www ENVISIONmonitor com support drivers asp to directly access the driver web page 10 31MY02 Envision Technical Support FAQ EN 985e Problem Possible Solution Power LED is not ON e Make sure the power button is ON e Make sure the power cord is properly connected to a grounded power outlet and to the monitor No Plug amp Play e Confirm that your computer is Plug amp Play compatible e Confirm that your video card is Plug amp Play compatible e Inspect the video cable and make sure that none of the pins are bent e Make sure the Envision monitor drivers are installed EN
5. Appendix EN 985e Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC Serial Data 5 Ground 13 H Sync 6 R Ground 14 V Sync 7 G Ground 15 DDC Serial Clock 8 B Ground 15 Pin Color Display Signal Cable EN 985e 15 31MY02 Envision This is a warranty statement for Envision color monitors including those sold within North America as specified Envision Peripherals Inc EPI warrants this product to be free from defects in material and workmanship for a period of three 3 years after the original date of consumer purchase During this period EPI will at its option either repair the defective product with new or rebuilt parts or replace it with a new or rebuilt product at no charge except as stated below The parts or product that are replaced become the property of EPI This limited warranty does not cover any losses or damages that occur as a result of Shipping or improper installation or maintenance e Misuse e Neglect Any cause other than ordinary commercial or industrial application e Adjustment by non authorized source e Repair modification or installation of options or parts by anyone other than an EPI Authorized Service Center Improper environment EN 985e Limited 3 Year Warranty EN 985e e Excessive or inadequate heating or air conditioning o
6. Envision EN 985e EN 985e 19 inch Flat CRT Color Monitor User s Manual by Envision Peripherals Inc www ENVISIONmonitor com Before operating your monitor please read this manual thoroughly Env s on EN 985e 1 31MY02 Env sion FCC Statement This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the eguipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help EN 985e For Your Safety EN 985e Notice 1 The changes or modifications not expressly appro
7. VISION monitor drivers are available at www ENVISIONmonitor com Picture is fuzzy e Adjust the Contrast and Brightness settings Picture bounces or a wave pattern is present in the picture e Move electrical devices away from the monitor They may be causing electrical interference Power LED is ON green or orange light is ON but there is no video or picture e Press a key on the keyboard or wiggle the mouse to re activate the monitor e Make sure the video cable is properly connected to the computer Inspect the video cable and make sure none of the pins are bent e Make sure your computer is operating correctly by pressing the CAPS LOCK key and observing whether the CAPS LOCK light turns ON or OFF Missing one of the primary colors RED GREEN or BLUE e Inspect the video cable and make sure that none of the pins are bent e Make sure the video cable is properly connected to the computer Screen image is not centered or sized properly e Adjust the Horizontal Vertical or Zoom settings in the OSD window Picture has color defects white does not look white e Adjust the User Color setting in the OSD window EN 985e 11 31MY02 Envision Appendix EN 985e Specifications CRT Size 19 0 48 3 cm Input Video Red Green Blue Analog Interface 11 4 29 mm neck Separate H V TTL 0 25mm D Syn
8. c 0 21mm H dot pitch H V Sync Positive Negative H Freguency 30 kHz 95 kHz 90 degree deflection V Freguency 50 Hz 160 Hz Viewable image size 18 0 45 3 cm Input Video Signal Analog diagonal 0 7 Vpp 75 OHM Positive Preset Display area 13 7 346 mm X 10 3 260 mm Power Source Universal AC 100 240 V Dot Clock 200 MHz 50 60 Hz z z z Factory Preset Mode 8 Maximum Resolution 1600 x 1200 pixels User Programmable Mode 20 Plug amp Play VESA DDC1 2B TM EPA ENERGY STARE Yes Power Consumption 130 Watts Maximum Regulatory UL CSA FDA Compliance FCC TUV GS MPRII EN 985e 12 31MY02 Envision Specifications continued Appendix Environmental Considerations Operating Temp 32 to 104 F 0 to 40 C ambient Operating Humidity 10 to 85 Signal Cable Attached Mini D sub 15 Male Optimal Viewing Mode 1280 x 1024 85 Hz EN 985e EN 985e 17 2 in 436 mm 17 6 in 446 mm lt 44 1 Ibs 20 0 Kg 13 31MY02 Envision Appendix EN 985e Factory Preset Timing Table Standard Resolution Horizontal Vertical in pixels Frequency Frequency VGA 720 x 400 31 5 kHz 70 Hz 640 x 480 31 5 kHz 60 Hz VESA 85 640 x 480 43 3 kHz 85 Hz 800 x 600 53 7 kHz 85 Hz 1024 x 768 68 7 kHz 85 Hz 1280 x 960 85 9 kHz 85 Hz 1280 x 1024 91 1 kHz 85 Hz VESA 75 1600 x 1200 93 8 kHz 75 Hz EN 985e 14 31MY02 Envision
9. d must terminate with a molded on type connector body rated 10A 250V having standard CEE 22 female configuration EN 985e For Your Safety EN 985e General Features e 19 48 3 cm Color Monitor e Crisp Clear Display for Windows Supports Resolutions up to 1600 X 1200 pixels 75Hz EPA ENERGY STAR Package Contents The box that your monitor was shipped in should have included the following items 1 EN 985e Color Monitor 2 Power Cord 3 Quick Start Guide 4 Booklet containing Warranty and Safety information 31MY02 Envision Before You Operate the Monitor Installing amp Removing the Base EN 985e Install EN 985e 31MY02 Envision Before You Operate the Monitor EN 985e Connecting the Wires Using the Power Cord Supplied Connect the built in video cable into the 15 pin connector on the back of your computer and tighten the two screws Connect the power cord into your monitor s power input socket Plug the other end of the power cord into a grounded AC outlet or UL approved power strip EN 985e Caution Make sure the power cord is the correct type that is required in your area This monitor has a universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage areas no user adjustment is required If the AC outlet is not grounded
10. e monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided e The monitor should be operated only with the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company e Disconnect the power cord to stop the power supply to the monitor EN 985e The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin As a safety feature this plug will only fit into a grounded power outlet If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or use an adapter to ground the appliance safely Do not defeat the safety purpose of the grounded plug Unplug the unit during a lightning storm or when it will not be used for long periods of time This will protect the monitor from damage due to power surges Do not overload power strips and extension cords Overloading can result in fire or electric shock Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor Do not attempt to service the monitor yourself open
11. ing or removing covers can expose you to dangerous voltage and other hazards Please refer all servicing to qualified service personnel To ensure satisfactory operation use the monitor only with UL listed computers which have appropriately configured receptacles marked between 100 240 V AC Min 3 5A The wall socket should be installed near the equipment and should be easily accessible 31MY02 Envision General Notes Do not install the monitor near heat sources such as radiators or air ducts e Do not place monitor in direct sunlight or in areas with excessive dust mechanical vibration or shock e Save the original shipping carton and packing materials in case you need to ship your monitor Be sure to repackage your monitor as it was originally packed at the factory e Periodically clean your monitor with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinners benzene or abrasive cleaners since these will damage the cabinet Always unplug the monitor before cleaning it Using the Right Power Cord The supplied power cord is a NEMA 5 15 style plug It is UL listed and CSA labeled for 125 volts AC If the monitor will be connected to your computer s power outlet use a minimum No 18 AWG type SJT or SVT three conductors cord with one end terminating with a male grounded plug rated 10A 250V CEE 22 The other en
12. monitor is on An orange light open this button allows you to move within indicates that the monitor is in Off mode the window and select desired functions Power Press this button to turn the D Contrast Press this button to adjust the monitor on or off The power indicator will o picture s contrast If the OSD window is light up open this button allows you to move within gt On screen Display OSD Press the the window and select desired functions El MENU button to open the OSD window sa s eo and adjust settings on your monitor See next page EN 985e 8 31MY02 Envision Adjusting the OSD Settings Language Adjusts the language selection oO Contrast O eo O U B v 3 Press MENU to open the function s window Press the lt or gt buttons to change the settings Adjusts the picture s contrast Brightness Adjusts the picture s brightness H Center Adjusts the horizontal position of the picture H Size Adjusts the horizontal size of the picture V Center Adjusts the vertical position of the picture V Size Adjusts the vertical size of the picture window function is highlighted of the function EN 985e E i SE z A e 6500 Press the MENU button to open the OSD Press the lt or gt buttons until the desired Operating Instructions Zoom Adjusts the vertical and horizontal size of the picture simultaneously Pincushion Adjusts
13. r electrical power failures surges or other irregularities This three year limited warranty does not cover any of the product s firmware or hardware that you or any third party have modified or altered you bear the sole responsibility and liability for any such modification or alteration All express and implied warranties for the product including the warranties of merchantability and fitness for a particular purpose are limited in duration to a period of three 3 years for parts and labor from the original date of consumer purchase No warranties either expressed or implied apply after this period In the United States some states do not allow limitations on how long an implied warranty lasts Therefore the above limitations may not apply to you EPI s obligations and your remedies hereunder are solely and exclusively as stated here EPI s liability whether based on contract tort warranty strict liability or other theory shall not exceed the price of the individual unit whose defect or damage is the basis of the claim In no event shall EPI be liable for any loss of profits loss of use or facilities or equipment or other indirect incidental or consequential damage In the United States some states do not allow the exclusion or limitation of incidental or consequential damages Therefore the above limitations may not apply to you 16 31MY02 Env sion Although this limited warranty gives you specific legal rights
14. ved by the party responsible for compliance could void the user s authority to operate the equipment 2 Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibility of the user to correct such interference As an ENERGY STAR Partner Envision Peripherals Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency Warning To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltage is present inside the monitor Do not open the cabinet Refer servicing to qualified personnel only 31MY02 Envision For Your Safety EN 985e Precautions Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of th
Download Pdf Manuals
Related Search