3044 - Hardware Manual
Contents
1. Hardware Manual ProDAQ 3044 Embedded Slot 0 Controller PUBLICATION NUMBER 3044 XX HM 0100 Copyright O 2007 Bustec Production Ltd Bustec Production Ltd World Aviation Park Shannon Co Clare Ireland Tel 353 0 61 707100 FAX 353 0 61 707106 PROPRIETARY NOTICE This document and the technical data herein disclosed are proprietary to Bustec Production Ltd and shall not without express written permission of Bustec Production Ltd be used in whole or in part to solicit quotations from a competitive source or used for manufacture by anyone other than Bustec Production Ltd The information herein has been developed at private expense and may only be used for operation and maintenance reference purposes or for purposes of engineering evaluation and incorporation into technical specifications and other documents which specify procurement of products from Bustec Production Ltd This document is subject to change without further notification Bustec Production Ltd Reserve the right to change both the hardware and software described herein ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual 3044 XX HM Table of Contents Ta OVERVIEW coito li eee 5 2 RELATED DOCUMENTS 2 0ccecceeceececcececeececceccececeececcecceceececeeceeceeseececeeseeseeseeeees 6 3 INSTALLATION AND PREPARATION ce cecceceeceeceececcececeeceececcecceseeseececeeseeseeees 7 3 1 OVERVIEW acertar ETE EE SAE EAN 7 3 2 UNPACKING2. due to special considerations for using the MVME6100 series board together with the ProDAQ 3040 adapter 3 4 Installation 3 4 1 PMC modules PMC modules mount on top of the MVME6100 single board computer part of the ProDAQ 3044 Please refer to the MVME6100 Single Board Computer Installation and Use manual for the steps necessary to install a PMC module on your board NOTE The MVME6100 provides two 32 64 bit PCI PCI X buses operating at a maximum frequency of 100 MHz when configured to PCI X mode and run at 33 or 66 MHz when running conventional PCI mode PCI bus 1 is connected to the PMC slots 1 and 2 The maximum PCI X frequency of 100 MHz supported by PCI bus 1 may be reduced depending on the number and or type of PMC PrPMC installed If PCI bus 1 is set to 5V VIO it runs at 33MHz VIO is set by the keying pins they are both a keying pin and jumper Both pins must be set for the same VIO on the PCI X bus The default setting is 5V VIO selecting PCI mode at 33MHz 3 4 2 ProDAQ 3044 Before installing the ProDAQ 3044 into your VXlbus mainframe ensure that the jumpers are configured properly any optional PMC modules are installed and the module enclosure is assembled properly Perform the following steps to install the ProDAQ 3044 in your mainframe 1 Attach an ESD strap to your wrist Attach the other end of the ESD strap to an electrical ground The ESD strap must be secured to your wrist and to ground throughout the whole
3. procedure Page 8 of 14 Copyright O 2007 Bustec Production Ltd ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual 3044 XX HM 2 If necessary perform an operating system shutdown on any computer affected by the installation Turn the AC or DC power off and remove the AC or DC power lines from the system Remove mainframe or system cover s as necessary to access the VXlbus slots 3 Remove filler panels from the selected slot if necessary If you intend to use the ProDAQ 3044 as slot 0 controller it must occupy the left most VXlbus slot in the system slot O If you do not intend to use it as slot 0 controller you may install it into any other free slot in your mainframe 4 Slide the ProDAQ 3044 into the selected slot Verify that the module is seated properly in the P1 and P2 connectors on the backplane Do not damage or bend connector pins 5 Secure the ProDAQ 3044 in the mainframe with the screws in the top and bottom of its front panel and verify proper contact with the traverse mounting rails 6 If your mainframe does not have an auto jumpering feature for the automatic propagation of the IACK and BG signals you might need to set or remove jumpers on the backplane to allow the proper handling of these signal lines Refer to your mainframe documentation for more information 7 If you want to use the factory installed debugger interactively connect the terminal that is to be used as the debugger system console to
4. rate of 9600 baud 8 bits per character 1 stop bit per character and no parity L ProDAQ 3044 DTE PC etc ule Pin Assignment Pin DB 9 2 1 DCD 4 DTR L 2 RTS 8 CTS No 3 GND 5 GND 4 TXD 2 RXD E 5 RXD 3 TXD vate 6 GND n c 2 7 CTS 7 RTS aT gt 8 DTR 1 DCD Figure 2 DEBUG Connector and Cable Pin Assignment Page 10 of 14 Copyright 2007 Bustec Production Ltd ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual 3044 XX HM 4 2 Front Panel Indicators The ProDAQ 3044 has two front panel indicators located in the DEBUG port RJ45 socket BFL yellow is asserted by the firmware to indicate a configuration problem or other failure CPU green is asserted directly by the CPU bus control signals to indicate CPU activity 4 3 Front Panel Switches The front panel of the ProDAQ 3044 incorporates a dual function toggle switch labelled ABT RST The ABT RST switch causes an interrupt signal to be generated This interrupt is normally used as an Abort signal for the processor to abort program execution and return control to the debugger firmware If pressed for more then three seconds the Reset function is selected and all on board devices are reset If the board is located in slot 0 and functions as a slot 0 controller a SYSRESET signal is generated Note The dual functionality of the Ab
5. ut o o ana So 7 3 3 HARDWARE PREPARATION ceceececceeceececeeceeceeceeaeceeceececaeeaececeeceeaecaecueceeseeaeeaeseeeeeas 7 DESCUPUO Nara 8 A NER eth a CA ace aaa ea i atc S 8 3 4 INSTALLATION qee a Edo Ee IO Ee Te IO E E OE EAD Re 8 3 4 1 PMC MOdUIOS 0 cccccccccccccccceceecucceccececueceeceacensenuecsadenensesuedsasensenusaeceasenseaes 8 3 4 2 PrODAQ2 3044 ois bot Sia Ua eee a a he 8 A OPERATION rei desioei eriten de ee dec reee e e e edere ereer Ero Cai Enida 10 4 1 FRONT PANEL CONNECTORS 0ccecceccecceceececeececeecuecueceeaecaecueceeseeaecuecueceeaeeaeeneseeans 10 ANA Ethernet POMS NIN Ed Se he hoa os 10 4 1 2 DEBUG POM suso Oe a Be ee 10 4 2 FRONT PANEL INDICATORS ecccceeceeceeceececeeceecuccecuecuecueceeaecaecueceeaesaecueceeseeeeueeneaes 11 4 3 FRONT PANEL SWITCHES 2 cccecceccecceceeceececeececaecuecueceeaecaecueceeaeeaececeeseeaecneeeeeneaes 11 4 4 LOGICAL ADDRESS SWITCH ccceccecceceeceececceececeecuecueceeaecaececeeseeaecaecuesesaeenesueeneaes 11 Copyright 2007 Bustec Production Ltd Page 3 of 14 3044 XX HM ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual List of Figures Figure 1 LAN Connectors Pin Assignment cceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeereee 10 Figure 2 DEBUG Connector and Cable Pin Assignment 10 Figure 3 Logical Address Switch Location eccseeeseseeeeeeeeeeeeeeeneeeeeeeeeeeeeteeeeeeeeeeees 11 Page 4
6. 6100A PG Programmer s Reference Guide MOTLoad Firmware Package User s Manual MOTLOADA UM Page 6 of 14 Copyright O 2007 Bustec Production Ltd ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual 3044 XX HM 3 Installation and Preparation 3 1 Overview The ProDAQ 3044 interfaces with the VXlbus via its P1 and P2 connectors and contains two IEEE 1386 1 PCI mezzanine card PMC slots It is user configurable by setting on board jumpers 3 2 Unpacking Before unpacking the ProDAQ module check the exterior of the shipping carton for any signs of damage All irregularities should be noted on the shipping bill The ProDAQ module is shipped in an antistatic package to prevent any damage from electrostatic discharge ESD Proper ESD handling procedures must always be used when packing unpacking or installing any ProDAQ module PMC module or similar Ground yourself via a grounding strap or similar e g by holding to a grounded object Discharge the package by touching it to a grounded object e g a metal part of your VXlbus chassis before removing the module from the package Remove the ProDAQ module from its carton preserving the factory packaging as much as possible Inspect the ProDAQ module for any defect or damage Immediately notify the carrier if any damage is apparent 3 3 Hardware Preparation The ProDAQ 3044 comes factory configured for operating as a VXlbus Slot 0 controller w
7. a C Size VXlbus system It translates VMEbus cycles into VXlbus cycles and vice versa In addition it houses the extensions necessary for VXlbus devices as there are the configuration registers a trigger and extended interrupt interface MODID support and the 10 MHz clock generation It forwards all VME master cycles transparently to the VXIbus allowing a VMEbus master the full access to the VXIbus On the VXIbus it allows the full integration of the module in the VXlbus resource management by providing a set of VXlbus compatible configuration registers and a configurable translation window in the VXlbus A24 or A32 address space Accesses to this translation window are forwarded to the VMEbus module s A16 A24 A32 or CR CSR space Programmable interrupt trigger and MODID support both detection and generation 10 MHz clock generation and auto Slot0 detection allow the board to be used as an embedded controller in Slot O and non Slot 0 applications Copyright 2007 Bustec Production Ltd Page 5 of 14 3044 XX HM _ ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual 2 Related Documents Bustec Production Ltd Documents Title ProDAQ 3040 6U VME64 to C Size VXI Adapter Hardware Manual Motorola Publication Number 3040 XX HM Motorola Computer Group Documents Title Motorola Publication Number MVME6100 Single Board Computer V6100A IH Installation and Use MVME6100 Single Board Computer V
8. an only be altered by changing the setting of the logical address switch To configure the ProDAQ 3044 dynamically the logical address switch must be set to 255 The resource manager will use the VXlbus MODID lines to access and configure the board and assigns a logical address during run time Page 12 of 14 Copyright 2007 Bustec Production Ltd Bustec Production Ltd World Aviation Park Shannon Co Clare Ireland Tel 353 0 61 707100 FAX 353 0 61 707106 Bustec Inc 35486 Lorain Road North Ridgeville OH 44039 U S A Tel 1 440 327 8930 Fax 1 440 327 8982
9. ith the Motorola MOTload debugger installed Depending on the application it might be necessary to change this configuration The ProDAQ 3044 provides software control over most of its configuration options by setting bits in control registers For additional information please refer to the MVME6100 Single Board Computer Programmer s Reference Guide and the ProDAQ 3040 6U VME64x to C Size VXlbus Adapter Hardware Manual Some options are not software programmable but controlled by manual installation or de installation of jumpers The following table lists the manually configured jumpers on the ProDAQ 3044 which have a fixed setting because of the ProDAQ 3040 adapter connected to the MVME6100 card For all other jumpers refer to the MVME6100 Single Board Computer Installation and Use manual Copyright 2007 Bustec Production Ltd Page 7 of 14 3044 XX HM ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual Jumper Description Setting Default J30 Front Rear Ethernet Select front panel ethernet SBC mode 3 13 and Transition Module and P2 ethernet not supported on the 4 14 Options Header 3044 Default Setting 5 15 6 16 7 17 8 18 9 19 10 20 J10 PMC SBC Mode 1 2 on both to select PMC mode SBC 1 2 J15 J18 Selection Headers mode not supported on the 3044 J25 J28 NOTE The settings described here supersede the settings as described in the manual MVME6100 Single Board Computer Installation and Use
10. of 14 Copyright O 2007 Bustec Production Ltd ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual 3044 XX HM 1 Overview The ProDAQ 3044 Slot 0 Controller provides a powerful platform for advanced embedded applications Using the first VME board designed with the new Tundra Tsi 148 VMEbus interface it is the first VXlbus slot 0 controller supporting the 2eVME protocol added in the VXlbus System Specification 3 0 allowing backplane transfer rates up to a theoretical maximum of 160 Mbytes second But the MVME6100 series provides more than just faster VMEbus transfer rates it provides balanced performance from the processor memory subsystem local buses and I O subsystems The processor running at speeds of 1 267 GHz is ideal for data intensive applications The state of the art host bridge with support for a 133 MHz host bus and a 133 MHz DDR memory bus is well matched to the processor To ensure that the MVME6100 series can handle the 160MB s data rates of 2eVME the Tsi148 VMEbus interface chip is connected to one of the 133 MHz PCI X buses on the host bridge The second PCI X bus has dual PMC X sites each site supports PMC or PMC X cards supporting PCI bus speeds from 33 to 100 MHz The MVME6100 also offers dual Gigabit Ethernet interfaces All of this adds up to a set of well balanced high performance subsystems for unparalleled performance The ProDAQ 3040 6U VME64x to C Size VXIbus Adapter allows the usage of 6U VMEbus boards in
11. ort Reset switch depends on the installed firmware If a different firmware then the factory installed Motorola MOTload debugger is installed the reaction on the ABT RST switch depends on this firmware 44 Logical Address Switch The ProDAQ 3044 Slot 0 Controller can operate as either a Slot 0 controller or as an embedded VXIbus controller non Slot 0 When the ProDAQ 3044 is operated as the Slot 0 controller it must be located in the left most slot slot 0 of a VXlbus System Specification Rev 1 3 or higher compatible VXlbus mainframe and be set for logical address zero 0 If the ProDAQ 3044 is operated as an embedded VXIbus controller non Slot 0 it may be located in any other slot and the logical address can be set to any Value between 1 and 255 LSB MSB Figure 3 Logical Address Switch Location Copyright O 2007 Bustec Production Ltd Page 11 of 14 3044 XX HM ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual Figure 3 shows the location of the logical address switch on the ProDAQ 3044 Set each switch to Off for a logical one 1 and to On for a logical zero 0 The picture shows the address switch set to logical address zero 0 If the ProDAQ 3044 is used in a non slot 0 position it can be either statically or dynamically configured To configure it statically the logical address switch must be set to a value between 1 and 254 This determines the logical address of the module permanently and c
12. the DEBUG port on the front panel of the ProDAQ 3044 8 Replace mainframe or system cover s and cable peripherals to the panel connectors as required 9 Reconnect the system to the AC or DC power source and turn the system power on Copyright 2007 Bustec Production Ltd Page 9 of 14 3044 XX HM ProDAQ 3044 Embedded Slot 0 Controller Hardware Manual 4 Operation 4 1 Front Panel Connectors There are three connectors located on the ProDAQ 3044 front panel two Ethernet connectors labeled LAN1 LAN2 and one serial port labeled DEBUG 4 1 1 Ethernet Ports ESY The two RJ 45 ports labeled LAN1 LAN2 provide the 10BaseT 100BaseTX and 1000Base T Ethernet LAN interface A standard ProDAQ 3044 CAT5e CAT6 network cable with RJ 45 connectors can be used to connect the ProDAQ 3044 to your LAN Pin 10Base T 100Base TX 1000Base T 1 TD MDIOO_P 2 TD MDIOO_N c 3 RD MDIO1_P 3 4 AC Terminated MDIO2_P 5 AC Terminated MDIO2_N 6 RD MDIO1_N 7 AC Terminated MDIO3 P 8 AC Terminated MDIO3_N E Figure 1 LAN Connectors Pin Assignment 4 1 2 DEBUG Port M Cc The RJ 45 port labeled DEBUG provides an RS 232 serial interface based on a TL16C550 UART controller chip It is asynchronous only 1 This port may be used to connect a terminal to the ProDAQ 3044 to serve as a console for the installed firmware or operating system By default the port is configured for a baud
Download Pdf Manuals
Related Search