Connectors - Jetway Computer
Contents
1. Help F5 Previous Values F6 Optimized Defaults F7 Standard Defaults Hard Disk Boot Priority The selection is for you to choose the hard disk drives priorities to boot from Virus Warning The selection Allow you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection If this function is enabled and someone attempt to write data into this area BIOS will show a warning message on screen and alarm beep 22 Disabled default No warning message to appear when anything attempts to access boot sector or hard disk partition table Enabled Activates automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector of hard disk partition table CPU Internal Cache The default value is Enabled Enabled default Enable cache Disabled Disable cache Note The internal cache is built in the processor External Cache Choose Enabled or Disabled This option enables the Level 2 cache memory Quick Power On Self Test This category speeds up Power On Self Test POST after you power on the computer If this is set to Enabled BIOS will shorten or skip some check items during POST Enabled default Enable quick POST Disabled Normal POST First Second Third Boot Device The BIOS attempts to load the operating system from the devices in the sequence selected in these items The settings are Floppy LS ZIP HDD 0 HDD 1 HDD 3 SCSI LAD and Disabl2. This will show CPU FAN System voltage chart and FAN Speed SFAN Smart Mode There are three choose Disabled Formula 1 Formula 2 Disabled Fan setting full speed Formula 1 Fan working low speed under temperature 2 Formula 2 Fan stop when under temperature 2 3 7 Power User Overclock Setting Phoenix AwardBIOS CMOS Setup Utility Power User Overclock Setting Profile Load Press Enter Item Help Profile Save Press Enter Hyper Transport Settings Press Enter Menu Level gt Current Host Frequency is 200MHZ CPU Clock at next boot is 200 Current DRAM Frequency is DDR533 DRAM Clock at Next Boot is Auto CPU Voltage Default 1 350v CPU Vcore x shift Default LDT Voltage 1 20v default NB Voltage 1 10v default VDIMM Voltage 1 84v default CPU Voltage 1 36 NB Voltage 1 11v VDIMM Voltage 1 84v i Move Enter Select PU PD Value Fl0 Save ESC Exit 1 Help F5 Previous Values F6 Optimized Defaults F7 Standard Defaults Phoenix AwardBIOS CMOS Setup Utility CPU VOLTAGE at NEXT BOOT Profile Load Press Enter Profile Save Press Enter Item Help Hyper Transport Settings Press Enter Current Host Frequency is 200MHZ CPU Clock at next boot is 200 Voltage Current DRAM Frequency is DDR533 DRAM Clock at Next Boot is Auto Default CPU Voltage Default 1 350v 1 550v CPU Vcore x shift Default LDT Voltage 1 20v default NB Voltage 1 10v default VDIMM Voltage 1 84v default
3. CPU Voltage 1 36v NB Voltage 1 11 VDIMM Voltage 1 84v 2 46v ENTER Accept ESC Abort fi 4 Move Enter Select PU PD Value F10 Save ESC Exit 1 1 Help F5 Previous Values F6 Optimized Defaults F7 Standard Defaults CPU Vcore This item allows you select the CPU Vcore Voltage xx more than the standard value by 29 this function for precise over clocking for extra demanding performance NB Voltage This item allows you to select value of Voltage for North Bridge Chipset AOD Compatibility Choose Enabled means only AMD over drive can adjust voltage Choose Disabled means only BIOS can adjust voltage Note Over standard voltage may damage device 30
4. Ethernet LAN function of providing 10Mb 100Mb Gigabit Ethernet data transfer rate Realtek ALC883 8 channel Audio Codec integrated Audio Audio driver and utility included Support SPDIF IN OUT Memory Socket PS 2 keyboard amp Mouse Connector D Sub 15 pin VGA Conn USB 2 0 connector x6 USB2 0 header x2 Multi I O Serial port D Sub x2 8 channel Audio connector Line out MIC and SPDIF in out DVI Conn 1 3 Layout Diagram amp Jumper Setting DVI Line In SPDIF in Keyboard Connector Surrback SPDIF out Connector 1 RJ45 LAN optional USB Connector Surround Connector Connector USB MIC IN Connector ATXI2V Power AMD Socket 2 Keyboard and USB Connector CPU FAN Wifi Clear CMOS LI VGA and DVI 240pin DDRII Connector DIMM Socket Audio Connector ATA133 USB Port Connector optional SATAII 1 2 3 4 ront Panel CD IN Connector 1 4 Connector Speak Connector 788444 Audi Power LED PCI Slot USB Port Connector Connector USB ALC 883 AUDIO CODEC RTL 8MB Flash SPI ROM BIOS 9 8111C PCI E LAN 1 8211B 25 mmm LAN PHY optional Jumper Jumper Name Descripion Page JBAT CMOS RAM Clear Function Setting 3 pin Block p9 Connectors Con
5. Technology You can choose from Enabled and Disabled MPS Version Control For OS 1 4 This option is only valid for multiprocessor motherboards as it specifies the version of the Multiprocessor Specification MPS that the motherboard will use OS Select For DRAM 64MB Allows 052 to be used with 64 or DRAM Settings are Non OS 2 default and OS2 Set to OS 2 if using more than 64MB and running 05 29 24 3 5 Intergrated peripherals Phoenix AwardBIOS CMOS Setup Utility Intergrated peripheral Onchip IDE Function Press Enter Onchip Device FUNCTION Press Enter Item Help Onchip Superio Funtion Press Enter USB Deivce Setting Press Enter Init Display First PCI Slot Menu Level gt gt N e Move Enter Select PU PD Value F10 Save ESC Exit 1 1 Help F5 Previous Values F6 Optimized Defaults F7 Standard Defaults Phoenix AwardBIOS CMOS Setup Utility OnChip Device Function Onboard HD Audio Device Auto HDMI Audio Auto Item Help Onboard PCIE LAN Device Enabled uid Move Enter Select PU PD Value F10 Save ESC Exit 1 Help F5 Previous Values F6 Optimized Defaults F7 Standard Defaults Onboard HD Audio This item allows you to decide to enable disable the chipset family to support HD Audio The settings are Enabled Disabled Onboard PCIE LAN Bootrom Decide whether to invoke the boot ROM of the onboard LAN chip 3 6 PC Health Status This section shows the Status
6. hard disk ribbon cable After connecting the single plug end to motherboard connect the two plugs at other end to your hard disk s You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector e Two hard disks can be connected to each connector The first HDD is referred to as the Master and the second HDD is referred to as the Slave For performance issues we strongly suggest you don t install CD ROM or DVD ROM drive on the same IDE channel as hard disk Otherwise the system performance on this channel may drop 14 1 SILI 3 Power switch PWR This 2 pin connector connects to the case mounted power switch to power ON OFF the system JW FP Power button bd Reset button Power LED 19 HD LED button button System Case Connections 15 4 Serial ATA Connector 7 female SATAIII SATAIDIZ SATAIIS SATAIIA This connector supports the provided Serial ATA2 IDE hard disk cable to connecting the motherboard and serial ATAII hard disk SATAL SATA2 SATA3 SATA4 n Serial ATA2 Port Connector E mun 2 6 Starting Up Your Computer After all connections a
7. CPU Voltage 1 36v NB Voltage 1 11v ENTER Accept VDIMM Voltage 1 84v ESC Abort Menu Level N e Move Enter Select PU PD Value F10 Save ESC Exit 1 Help F5 Previous Values F6 Optimized Defaults F7 Standard Defaults Phoenix AwardBIOS CMOS Setup Utility CPU VCORE x SHIFT Profile Load Press Enter Item Help Profile Save Press Enter Hyper Transport Settings Press Enter CPU Vcore x shift Current Host Frequency is 200MHZ CPU Clock at next boot is 200 Default Current DRAM Frequency is DDR533 41 65 DRAM Clock at Next Boot is Auto 3 28 CPU Voltage Default 1 350v CPU Vcore x shift Default LDT Voltage 1 20v default 50 NB Voltage 1 10v default VDIMM Voltage 1 84v default TL Move ENTER Accept ESC Abort 28 CPU Voltage Menu Level NB Voltage VDIMM Voltage Ti Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Optimized Defaults F7 Standard Defaults hoenix AwardBIOS CMOS Setup Utility VDIMM SELECT Profile Load Press Enter Item Help Profile Save Press Enter Hyper Transport Settings Press Enter Current Host Frequency is 200MHZ CPU Clock at next boot is 200 Menu Level gt Current DRAM Frequency is DDR533 DRAM Clock at Next Boot is Auto CPU Voltage Default 1 350v CPU vore Default E LDT Voltage 1 20v default NB Voltage 1 10v default 1 74v VDIMM Voltage 1 84v default 1 79v
8. NTY OF ANY KIND AND WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTIAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMANGES FOR LOSS OF PROFIT LOSS OF BUSINESS LOSS OF USE OF DATA INTERRUPTION OF BUSINESS AND THE LIKE PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER S BENEFIT WITHOUT INTENT TO INFRINGE Manual Revision Information Reversion Revision History Date 2 0 Second Edition May 2008 Item Checklist Motherboard Cable for IDE Port CD for motherboard utilities Motherboard User s Manual Back panel optional DVI to HDMI Connector Chapter 1 Introduction of the Motherboard 1 1 Feature of motherboard The motherboard series are designed for the new generation AMD processor family guaranteed both of the performance and stability of general purpose IPC and dedicated IPC platform solutions The MCP78S chipset is fully optimized to provide the variety IPC platform solutions by featuring the high compatibilities and cost effective low power consumption high performance and superior core graphics engine The motherboard AMD Socket 2 Quad core Opteron amp Phenom with low power consumption never denies high performance The embedded AMD Socket 2 Quad core Opteron amp Phenom family processor has evolved to meet the specific
9. TECHNICAL MANUAL Of NVIDIA MCP78S Based Mini ITX M B For AMD Socket AM2 Processor NO G03 J6C2 F G03 NC62 F Rev2 0 Release date May 2008 Trademark Specifications and Information contained in this documentation are furnished for information use only and are subject to change at any time without notice and should not be construed as a commitment by manufacturer Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding To minimize pollution and ensure environment protection of mother earth please recycle TABLE OF CONTENT USER NOTICE inm MEN EE iii MANUAL REVISION iii ITEM CHECKLIST PEE iii CHAPTER 1 INTRODUCTION OF AMDCSS5536 CHIPSET MOTHERBOARD 1 1 FEATURE OF MOTHERBOARD wesccsscscssssscssssssssssssssssesssesessscssssscessnscessnscessnssesssssessseeessse 1 1 1 1 SPECICAL FEATURE OF 5 2 13 SPECIFICATION dpt PER RD Nm 3 1 LAYOUT DIAGRAM amp JUMPER 5 5 CHAPTER2 HARDWARE INSTALLATION 2 1 HARDWARE INSTALLATION 8 8 2 2 CHECKING MOTHERBOARD S JUMPER SETTING eeeennnnttennnntennnnettnnnns 8 2 3 INSTALL MEMORY 2 4 EXPANSION CARDS 2 4 1 PROCEDURE FOR EXPANSION CARD INSTALLATION enne 11 2 5 CONNECTORS AND HEADERS
10. e highlighted item To exit the Help Window press Esc 3 3 The Main Menu Once you enter Award BIOS CMOS Setup Utility the Main Menu Figure 3 1 will appear on the screen The Main Menu allows you to select from fourteen setup functions and two exit choices Use arrow keys to select among the items and press Enter to accept or enter the sub menu 19 Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Thermal Throttling Options Advanced BIOS Features Power User Overclock Settings Advanced Chipset Features Password Settings Integrated Peripherals Load Optimized Defaults Power Management Setup Load standard Defaults Miscellaneous Control Save amp Exit Setup PC Health Status Exit Without Saving Quit F9 Menu in BIOS Ne Select Item Save amp Exit Pen Figure 3 1 Standard CMOS Features Use this Menu for basic system configurations Advanced BIOS Features Use this menu to set the Advanced Features available on your system Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system s performance Integrated Peripherals Use this menu to specify your settings for integrated peripherals Power Management Setup 20 Use this menu to specify your settings for power management Miscellaneous Control Use this menu to specify your settings for Miscellaneous Control PC Health Status This entry shows your PC health status Power User Overcl
11. ed Boot Up Floppy Seek During POST BIOS will determine if the floppy disk drive installed is 40 or 80 tracks 360K type 15 40 tracks while 760K 1 2M and 1 44M are all 80 tracks Boot Up NumLock Status The default value is On On default Keypad is numeric keys Off Keypad is arrow keys Gate A20 Option Normal The A20 signal is controlled by keyboard controller or chipset hardware 23 Fast default The A20 signal 15 controlled by port 92 or chipset specific method Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be selected The settings are Enabled Disabled Typematic Rate Chars Sec Sets the number of times a second to repeat a keystroke when you hold the key down The settings are 6 8 10 12 15 20 24 and 30 Typematic Delay Msec Sets the delay time after the key is held down before beginning to repeat the keystroke The settings are 250 500 750 and 1000 Security Option This category allows you to limit access to the system and Setup or just to Setup System The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt Setup default The system will boot but access to Setup will be denied if the correct password is not entered prompt HDD S M A R T Capability This option allow you to enable the HDD S M A R T Capability Self Monitoring Analysis and Reporting
12. ee short Video card not found or video card memory gt High frequency beeps when system is CPU overheated working System running at a lower frequency 6 During power on press Delete key to enter BIOS setup Follow the instructions in BIOS SETUP 7 Power off your computer You must first exit or shut down your operating system before switch off the power switch For ATX power supply you can press ATX power switching after exiting or shutting down your operating system If you use Windows 9X click Start button click Shut down and then click Shut down the computer The power supply should turn off after windows shut down 17 Chapter 3 Introducing BIOS The BIOS is a program located a Flash Memory on the motherboard This program is a bridge between motherboard and operating system When you start the computer the BIOS program will gain control The BIOS first operates an auto diagnostic test called POST power on self test for all the necessary hardware it detects the entire hardware device and configures the parameters of the hardware synchronization Only when these tasks are completed done it gives up control of the computer to operating system OS Since the BIOS is the only channel for hardware and software to communicate it is the key factor for system stability and in ensuring that your system performance as its best In the BIOS Setup main menu of Figure 3 1 you can see several options We will exp
13. ents Failure to do so may cause severe damage to both your motherboard and expansion cards 2 4 1 Procedure For Expansion Card Installation 1 Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers Remove your computer s cover and the bracket plate on the slot you intend to use Align the card s connectors and press firmly Secure the card on the slot with the screen you remove above Replace the computer system s cover Set up the BIOS if necessary Install the necessary software driver for your expansion card du et 11 2 5 Connectors and Headers 2 5 1 Connectors 1 12V Power Connector 4 pin block 12V CN This is a newly defined 4 pins connector support extra 12V voltage to maintain system power consumption in the case that an AD Scalar daughter board is used Without this connector might cause system unstable because the power supply can not provide sufficient current for system 2 USB Port connector UL3 UL4 The connectors are 4 pins connector that connect USB devices to the system board and standard RJ45 connector for Network supports 10 100 1000 BASE T transfer rate 3 LAN Port connector UL3 UL4 optional This connector is standard RJ45 over USB connectors for Network devices connection LAN supports 10M 100Mb s data transfer rate 4 VGA Connector 15 pin female VGA VGA Connector is a 15 pin D Subminia
14. esktop PCs High density servers Home server appliances Public information entertainment kiosks Point of Sales systems Intelligent displays Edge networking devices Hospital monitoring systems Municipal control amp monitoring systems 1 1 1 Special Feature of motherboard OC CON CHigh polymer Solid Electrolysis Aluminum Capacitors The working temperature is from 55 degrees Centigrade below zero to 125 degrees Centigrade OC CON capacitors possess superior physical characteristics that can be while reducing the working temperature between 20 degrees Centigrade each time intact extension 10 times of effective product operation lives at not rising degrees Centigrade of working temperatures each time a relative one life of product decline 1046 only too 1 2 Specification Spec Description Mini ITX form factor 6 layers PCB size 17 0x17 0cm Chipset NVIDIA MCP78S single chipset Embedded CPU a Low Power Consumption Socket AM2 AM2 AMD CPU 240 pin DDRII DIMM socket x1 Support DDRII 667MHz DDRII 800MHz system Modules DDR memory Expandable to 2GB Expansion Slots 32 bit PCI slot x 1pcs One PCI IDE controller that supports PCI Bus Mastering ATA Integrate IDE PIO DMA and the ULTRA DMA 133 100 66 functions that nee deliver the data transfer rate up to 100 MB s Integrated Realtek RTL8111B C PCI E LAN LAN Integrated Realtek RTL8211B LAN PHY LAN optional Support Fast
15. hooting 2 Forget password 3 After over clocking system boot fail 1 3 1 2 closed Normal Default 2 3 closed Clear CMOS CMOS RAM Clear Setting 2 3 Install Memory The motherboards provide one 240 pin DDRII MEMORY MODULE sites for memory expansion available from minimum memory size of 64MB to maximum memory size of 2 0GB DDRII SDRAM Valid Memory Configurations 240 Pin DIMM Total Memory Bank 0 1 DDRII DDRII 800 DDRII667 DDRIIS33 64MB 2 0GB DDRII SDRAM Module System Memory Max 2 0GB 64MB 2 0GB Generally installing DDRII memory to your motherboard is very easy you can refer to figure 2 4 to see what a 240 Pin DDR 800II DDRII 667 DDR SDRAM module looks like 0 amp DIMMI NOTE When you install DIMM module fully into the DIMM socket the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides WARNING For the DDR SDRAM CLOCK is set at 166MHz use only DDR333 compliant DDR Modules When this motherboard operate at 133MHz most system will not even boot if non compliant modules are used because of the strict timing issues if your SDR Modules are not DDR333 compliant set the DDR SDRAM clock to 133MHz to ensure system stability 10 2 4 Expansion Cards WARNING Turn off your power when adding or removing expansion cards or other system compon
16. lain these options step by step in the following pages of this chapter but let us first see a short description of the function keys you may use here e Press lt Esc gt to quit the BIOS Setup Press The gt up down left right to choose in the main menu the option you want to confirm or to modify Press when you have completed the setup of BIOS parameters to save these parameters and to exit the BIOS Setup menu Press Page Up Page Down or keys when you want to modify the BIOS parameters for the active option 3 1 Entering Setup Power on the computer and by pressing lt Del gt immediately allows you to enter Setup 18 If the message disappears before your respond and you still wish to enter Setup restart system to try again by turning it OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing Ctrl Alt and Delete keys If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press F1 to continue lt Ctrl Alt Esc gt or Del to enter Setup 3 2 Getting Help Main Menu The on line description of the highlighted setup function is displayed at the bottom of the screen Status Page Setup Menu Option Page Setup Menu Press to pop up a small help window that describes the appropriate keys to use and possible selections for th
17. nectr Name Description Page 12V CN 4 Pin 12V Power Connector 4 pin Block USB1 USB2 USB Port Connector Headers Header Name Description _ Page USB1 USB2 USB2 0 Port Headers 9 pin Block 44 Pin IDE Connector 44 pin IDE Block RESET Reset switch lead PWR BTN Power Button Headers 15 5 2 3 4 Serial ATA Headers 7 pin Female Connector Expansion Sockets SockeUSlot Name Descripion Page DDRII DDRIISDRAM Module 240 pin DDR SODIMM Module p 10 Socket Expansion Socket Chapter 2 Hardware installation 2 1 Hardware installation Steps Before using your computer you had better complete the following steps 1 Check motherboard jumper setting 2 Install System Memory DIMM 3 Install Expansion cards 4 Connect IDE Front Panel Back Panel cable 5 Connect Power connector 6 Install Operating System 7 Install Driver and Utility 2 2 Checking Motherboard s Jumper Setting 1 Clear CMOS 3 pin JBAT A battery must be used to retain the motherboard configuration in CMOS RAM short 1 2 pins of JBAT to store the CMOS data To clear the CMOS follow the procedure below 1 Turn off the system and unplug the AC power 2 Remove ATX power cable from ATX power connector 3 Locate JBAT and short pins 2 3 for a few seconds 4 Return JBAT to its normal setting by shorting pins 1 2 5 Connect ATX power cable back to ATX power connector Note When should clear CMOS 1 Troubles
18. ock Settings Use this menu to specify your settings frequency Voltage for overclocking demand CPU Thermal Throttling Setting The selection is set for activating the active CPU Thermal Protection by flexible CPU loading adjustment in the arrange of temperature you define Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use Password Settings This entry for setting Supervisor password and User password Save amp Exit Setup Save CMOS value changes to CMOS and exit setup Exit Without Saving Abandon all CMOS value changes and exit setup 21 3 4 Advanced BIOS Features Phoenix AwardBIOS CMOS Setup Utility CPU Feature Hard Disk Boot Priority Virus Warning CPU Internal Cache External Cache Quick power on self Test First Boot Device Second Boot Device Third Boot Device Boot other Device Boot Up NumLock Status Gate A20 option Typematic Rate Setting Typematic Rate Chars Sec Typematic Delay Msec Security Option APIC Mode MPS Version Control For OS OS Select For DRAM gt 64MB HDD S M A R T Capability Advanced BIOS Features Press Enter Press Enter Disabled Enabled Enabled Enabled Removable Hard Disk CDROM Enabled On Fast Disabled 6 250 Setup Enabled 1 4 Non OS2 Disabled Item Help Menu Level 71 gt gt lt Move Enter Select PU PD Value F10 Save ESC Exit 1
19. oesssssscssssssssssccsssecsssssssssesesssesesnsssssnscesssecessssssessessesseessseeess 12 2 51 CONNECTORS wecscssssssssscsssesesssscccsscscsssssccsssesssssesssssesssscsnsessnecessnsssssassesssssessseeessees 12 25534 HEADERS 14 2 6 STARTING UP YOUR COMPUTER oesccssssssssssssssssssssssssssccsssccsssssssssesssssesssssssssssesssssessseees 16 3 3 1 ENTERING 58 18 30 GETTING BP eet vu el peccat p a PR 19 3 3 THE MAIN MENU c sccccscssscccssscccccsssceccsssesecesscccecessecccesscccscescsscessecceeses 19 3 4 ADVANCED BIOS 6 0 000 22 3 5 INTERGRATED PERIPHERALS sscccssssssssssssssssssscsssscssssssscesssesssssesessussesssssensssscessneseesese 25 3 6 HEALTH 8 25 3 7 POWER USER OVERCLOCK 27 USER S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER NO PART OF THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE INTEL 945GM CHIPSET MOTHER BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER S REQUIREMENT BUT WILL CHANGE CORRECT ANY TIME WITHOUT NOTICE MANUFACTURER PROVIDES THIS MANUAL IS WITHOUT WARRA
20. of you CPU Fan and Warning for overall system status This is only available if there is Hardware Monitor onboard 25 Phoenix AwardBIOS CMOS Setup Show PC Health in Post Smart FAN Configuration Vcore VDIM NB 5V 12V 5VSB VBAT CPU Temperature SYS Temperature CPUFAN Speed SYS FAN1 Speed SYS FAN2 Speed PC Health Status Enabled Press Enter 1 36V 1 84V 1 12V 5 04V 11 96V 5 04V 3 17V 37 C 98F 40 C 104F 0 RPM 0 RPM 1514 RPM Utility Item Help Menu Level gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Optimized Defaults F7 Standard Defaults Show PC Health in Post During Enabled it displays information list below The choice is either Enabled or Disabled CPU Smart FAN Configurations CPU Full Speed Temp This item allows you setting the FAN works in full speed when the temperature over the value which out If the temperature below the value but over the Idle Temperature the FAN will works over 60 of full speed and the higher temperature will gain higher FAN speed after over the temperature which this item setting the FAN works in full speed CPU Idle Temp This item allows you setting the FAN works in 60 of full speed when the temperature lower than the temperature which you setting Current CPU Temperature Current System Temp Current FAN1 FAN2 Speed Vcore Vdd 3 3V 5V 12V 12V VBAT V S5VSB V 26
21. re made close your computer case cover 2 Be sure all the switch are off and check that the power supply input voltage is set to proper position usually in put voltage is 220V 240V or 110V 120V depending on your country s voltage used 3 Connect the power supply cord into the power supply located on the back of your system case according to your system user s manual 4 Turn on your peripheral as following order a Your monitor b Other external peripheral Printer Scanner External Modem etc c Your system power For ATX power supplies you need to turn on the power supply and press the ATX power switch on the front side of the case 16 5 The power LED on front panel of system case will light The LED on monitor may light up or switch between orange and green after the system is If it complies with green standards or if it is has a power standby feature The system will then run power on test While the test is running the BIOS will alarm beeps or additional message will appear on the screen If you do not see any thing within 30 seconds from the time you turn on the power The system may have failed on power on test Recheck your jumper settings and connections or call your retailer for assistance One short 2 when displaying logo No error POST Long Long beeps an endless loop in an endless loop No DRAM install or DRAM install or detected One long beep followed by thr
22. requirements of extended temperature applications in telecommunications infrastructure including wired wireless and BSC MSC single board computing automotive and transportation systems and industrial control and monitoring The motherboard series support HT3 0 and DDRII 400 533 667 800 system RAM Modules which is expandable to 2 0GB The motherboard offers ULTRA ATA 133 HDD connectors and Serial ATA2 with RAID 0 1 5 10 JBOD functions which support up to IDE and four Serial ATA2 devices to accelerate hard disk drives and guarantee the data security without failure in advanced computing performance The motherboard provide two Gigabit Ethernet LAN for internet or intranet connections one is PCI E LAN the other one is PHY LAN optional The motherboard series are also integrated Realtek ALC883 8channel Audio CODEC on system which is fully compatible with Sound Blaster Pro that gives you the best sound quality and compatibility Embedded 10 USB2 0 functional ports delivering 480Mb s data transfer rate these motherboards meet USB2 0 demands data transport demands which are also equipped with hardware monitor function on system to monitor and protect your system and maintain your non stop business computing Targets at High Growth Markets Digital Home Digital Office Digital World Personal electronics such as personal video recorders PVR set top boxes home theatres digital audio centers etc Mini PCs Green clients Quiet d
23. ture Receptacle connector This connector is for connection Monitor and System to display 12 5 DVI Connector 24 pin female DVI DVI Connector is a 24 pin D Subminiature Receptacle connector This interface standard designed to maximize the visual quality of digital display devices such as flat panel LCD computer displays and digital projectors 6 Audio Connector Line Out MIC This Connector is 2 phone Jack for LINE OUT MIC Line in BLUE Audio input to sound chip Line out GREEN Audio output to speaker MIC PINK Microphone Connector Surrback ORANGE Audio output to speaker Rear speaker out CEN BASS BLACKNESS Audio output to speaker Center Subwoofer speaker out Surround GRAY Audio output to speaker Side speaker out Kevboard DVI Line In e s LAN Connector Connector Connector Connector 7 PS 2 Keyboard Mouse Connector PS2KB The connectors are for PS 2 keyboard mouse device 13 2 5 2 Headers 1 USB Port Headers 9 pin USBI USB2 These headers are used for connecting the additional USB port plug By attaching an option USB cable your can be provided with two additional USB plugs affixed to the back panel 2 Connector OOOOO Pini gt ta OOOOO 1 tttt BERS USB Port Header This connector supports the provided IDE
Download Pdf Manuals
Related Search