Data Sheet - Mouser Electronics
Contents
1. 6 1 5 ADC The BISM II PA provides access to two 8 bit ADCs These provide an input range of OmV to 1 800mV which can be read using the S registers 701 and 702 Suitable external scaling and over voltage protection should be incorporated in your design The module provides 5 samples per second at the UART with a baud rate of 115 200 or above Low latency access of the upper 6 bits of the ADCs can be obtained by using EZURiO s I O via an enhanced inquiry process 7 Integrated Firmware 7 1 General The BISM II PA has been designed to provide the fastest route to market for designers who wish to use Bluetooth to wirelessly enable their products To achieve this EZURIO has implemented a wide ranging set of AT commands that control all of the standard Bluetooth tasks These remove the complexity of Bluetooth from the design engineer and allow the wireless link to be controlled by means of a simple set of commands For applications where multiple concurrent live connections need to be maintained a variant of firmware is available which is specifically targeted at multipoint operation For both applications a comprehensive range of windows based software is available to speed up the design process A low cost development kit is also available that can be used for prototyping both cable replacement and multipoint applications 7 2 Profiles Bluetooth has been designed to accommodate a very wide range of wireless applications To enable2. www EZURiO com 7 4 Multipoint Firmware For multipoint operation the same hardware can be loaded with multipoint software Whereas the firmware for single point AT communication only allows one connection to be active at any one time using multipoint firmware allows a number of simultaneous connections to be made and maintained It also allows connections to multiple profiles to one or more devices Multipoint firmware should be seen as a concept of channels instead of slave connections When operating in Bluetooth multipoint mode the resources and bandwidth of a Bluetooth master device are shared amongst the different connected devices This has an impact on the maximum throughput to any one device If multiple device connections are maintained it also impacts on the memory resources and device database within the Bluetooth stack Designers should be aware of these restrictions when using multipoint configurations In most cases better latency and power consumption can be achieved by polling or fast data transfer rather than by maintaining concurrent connections In general multipoint connections are viable for up to three connections at which point memory constraints start to limit the actual data rates For more than three connections other connection schemes offer a more efficient approach Contact EZURiO for more information 7 5 OTA Over the Air Configuration When the BISM II PA has its remote AT parser enabled its settings
3. 12 3 2 1 FCC Labelling requirement If the FCC ID is not visible when the module is installed inside another device then the outside of the device into which the module is installed must also display a label referring to the enclosed module This exterior label can use wording such as the following Contains Transmitter Module FCC ID PI409B or Contains FCC ID PI409B Any similar wording that expresses the same meaning may be used 12 3 3 National RF approvals A list of the countries where the Module is approved will be provided by EZURiO as required As a minimum the product is listed in Europe Scandinavia Canada and USA EZURIiO assumes no liability for customer failure to comply with national RF approval 12 3 3 1 R amp TTE Notification Requirement The 2 4GHz band has some restrictions within the EU when the transmit power level is greater than 10mW R amp TTE Class 2 Because of this it is designated within R amp TTE as a non harmonised band Such products must be notified to the appropriate Notified Body within each country where it is placed on the market EZURiO has notified the WISM module but manufacturers incorporating it within their products and intending to sell these within Europe have a responsibility to notify the appropriate nominated body before commercial introduction A list of nominated bodies is available at http eur lex europa eu LexUriServ site en oj 2003 c 302 c 30220031212en00010414 pdf Further
4. PA and carrier pcb to be changed from 3 5mm to 5 0mm Item Part number Stacking height HRS number Receptacle on DF12C 40DS 0 5V 86 3 5 mm 5 mm CL537 0007 7 86 Module Headers DF12 series DF12 3 5 40DP 0 5V 86 CL537 0032 4 86 Notes The headers listed above are with boss and metal fitting Suffix 86 denotes ROHS compliance H Stacking Height mm BISM with Receptacle z of N IL 1 fa Mating Board with Header 11 2 Hirose Connector general specification Parameter Specification 40 pin Board to Board connector Number of Contacts 40 Quantity delivered 2000 Connectors per Tape amp Reel Voltage 50V Current Rating 0 5A max per contact Resistance 0 05 Ohm per contact Dielectric Withstanding Voltage 500V RMS min Operating Temperature 45 C 4125 C Contact Material phosphor bronze surface gold plated DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 24 2007 8 EZURIiO Ltd www EZURiO com Insulator Material PA beige natural Stacking height 3 0 mm 3 5mm 4 0 mm 5 0 mm Insertion force 21 8N Withdrawal force 1st 10N Withdrawal force 50th 10N Maximum connection cycles 50 12 Qualification 12 1 Qualification Process The following safety precautions must be observed during all phases of the operation usage service or repair of any application incorporating this Module Manufacturers of the RF equipment are advised to convey the following safety information to users and operating personnel and
5. The operating mode can best be described by stating the AT commands required to enter that mode In addition there are certain S Registers which have a direct impact on power consumption which are described next S Registers 508 to 511 which specify the page and inquiry scan intervals and windows can be used to adjust the average current drain when in discoverable and or connectable modes Registers 508 and 509 specify the interval and window for page scans and registers 510 and 511 specify the interval and window for inquiry scans Register pairs 508 509 and 510 511 describe duty cycles when the module goes into scan modes It is while scanning that the highest current draw occurs The DSH_BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 14 2007 8 EZURiO Ltd www EZURiO com average current draw is determined by simple arithmetic using the values stored in the 508 509 and 510 511 register pairs Typical current consumption is given in Section 4 1 The current drain while waiting for a connection or discoverable mode is about 30 times higher than in idle mode This is when the page inquiry scan duty cycle is 100 These modes give the quickest response to a page or inquiry request from a remote peer It is possible to reduce the duty cycle down to as low as 0 5 at the expense of response time The response time can be specified via S Registers 508 and 510 for page and inquiry respectively where the worst case response time can be as high as 2 5 s
6. can be accessed synchronously The ports are powered from Vcc The mode of these lines can be configured and the lines are accessed via S Registers 623 to 629 Low latency I O can be accessed by using EZURiO s I O via an enhanced inquiry process 6 1 4 PCM CODEC Interface PCM _OUT PCM_IN PCM_CLK and PCM_SYNC carry up to three bi directional channels of voice data each at 8ksamples s The format of the PCM samples can be 8 bit A law 8 bit u law 13 bit linear or 16 bit linear The PCM CLK and PCM_SYNC terminals can be configured as inputs or outputs depending on whether the module is the Master or Slave of the PCM interface Please contact an EZURiO FAE for further details The Module is compatible with the Motorola SSI TM interface and interfaces directly to PCM audio devices including the following 6 1 4 1 Compatible Codec Chips e OKI 7702 single channel A law and law CODEC DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 10 2007 8 EZURiO Ltd www EZURiO com e OKI MSM7705 four channel A law and u law CODEC e Winbond W681360 13 bit linear CODEC 6 1 4 2 Audio Codec Development Boards EZURiO supplies a range of audio codec evaluation boards to allow rapid development of audio applications These connect to the PCM output connector of EZURIO s Wireless Development Kit Order Numbers for these boards are ACC 006 OKI 7702 single channel CODEC ACC 007 OKI 7705 four channel CODEC ACC 005 Winbond W681360 13 bit linear CODEC
7. connection e HSP Headset Profile AG Supports early implementations of headsets Now largely replaced by the e HFP Hands free profile AG which provide more control over the headset operation e FIP File Transfer Profile Server The Audio Gateway requirements of Headset and Handsfree profiles are implemented within the AT Command firmware For full profile Support a portion of these profiles must be implemented within the host system For other profile support please contact EZURiO Ltd at blu2i EZURIO com 7 3 AT Overview The AT command set is well known by engineers and was developed to aid the integration of PSTN modems It provides simple high level commands for complex functions that can easily be incorporated into programs or used within programming scripts EZURiO has used this familiar concept and extended it to Bluetooth to simplify the integration of Bluetooth for product designers Rather than having to understand the many stages of setting up a Bluetooth connection or function a single AT command is all that is required For example to connect to a Bluetooth device with an address 00809844EA13 all that is needed is to send the string ATDO0809844EA13 to the UART of the BISM II PA module The module will attempt to make a connection and return connect 00809844ea13 1101 or NO CARRIER depending on whether the connection was successful The scope of the AT command set developed by EZURiO is such that most Bluetoo
8. connection and may require a power cycle to reset the module EZURiO recommend that the correct CTS RTS handshaking protocol be adhered to for proper operation DSH_BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 17 2007 8 EZURiO Ltd www EZURiO com Notes i DSR is used by the module to sense that the host is connected and is intricately linked with connections For outgoing calls if this line is not asserted then an error is indicated Similarly for AT BTP and AT BTG While in a call for appropriate modes a de assertion means fall into command state If the de assertion exists for longer than the period specified in S Register 519 then the connection is dropped as if an ATH command was received 2 RI is normally de asserted When an incoming connection is detected it will be asserted until the connection is either answered or rejected using ATA and ATH respectively See S Registers 552 amp 553 for more details 3 DCD will be de asserted when the device is in the unconnected state Asserted when a connection is active See S Registers 552 and 553 for more details 4 PIO3 is either used as GPIO or driven as UART_DTR When the unit is configured in pure host mode this pin is forced into UART_DTR and is asserted when there is a Bluetooth connection GPIO Pins 3 to 9 are available for general purpose use 9 2 Modem signalling over Bluetooth The RFCOMM protocol used in Bluetooth for implementing the serial port profile allows for the
9. crystal on the customer s main pcb The frequencies available are e 8 MHz e 16 MHz For more implementation details refer to EZURiO s Application Note APN_06004_1v0 Crystal Output from BISM pdf DSH _BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 20 2007 8 EZURiO Ltd www EZURiO com 10 Application Information 10 1 Antenna Position The antenna used on the BISM II PA Bluetooth module is designed to be largely immune from the effects of proximity detuning Normally antennas operating at 2 4GHz are affected by their Surroundings so that great care is needed in their placement and orientation The BISM II PA can be used in most locations and orientations and is only marginally affected by the presence of a significant ground plane in close proximity The antenna distribution is close to isotropic which means that the orientation of mounting has only a limited effect on the overall range However the optimum range is achieved when the two antennae are directly facing each other Example of Radiation Characteristics Horizontal Polarisation Vertical Polarisation 2 400 GHz 2 442 GHz 2 485 GHz 90 180 180 Typical Radiation Characteristics Measured at 2 5metres from a standard dipole The module should not be located in a sealed metal enclosure as this will act as a Faraday cage and severely attenuate the radio signal The antenna finish may tarnish as a result of environmental effects and handli
10. exchange of four modem signals This information is contained in a special transparent message which contains bits identified as RTR RTC DV and IC which depending on the type of serial device being emulated maps to DTR or DSR RTS DCD and RI respectively In addition this message also includes the ability to convey a BREAK input from one end to the other To allow for the greatest flexibility and variability in how the modem control signals are used out in the real world S Registers 551 552 and 553 have been provided which allow for any of RTR RTC DV and IC to be mapped to any modem control status line BREAK signal on RX line If the host sends a break signal of duration greater than 100ms then the module is configured to treat that as a signal to perform a hardware reset For obvious reasons it is not possible to convey a BREAK over Bluetooth to the peer device 9 3 Pure Cable Replacement Mode The module has the capability of being preset into a pure 5 wire data cable replacement mode The 5 wires being RX TX CTS RTS and GND This mode requires no changes to a host application since the Bluetooth connection is automatically set up on power up If the connection is lost the BISM II PA module will constantly retry until the connection is reinstated By implication two devices are needed to replace a cable One device is pre configured to always be a master and the other a slave Assuming the Bluetooth address of the master to be
11. programmed 3 3 2 4 SPI Bus nat wane Pinno iro eommenis SPI_MOSI we Je Used to reprogram Flash Gauss fo Ses o ooo re sr 3 3 2 5 PCM Interface PCM_CLK 20 rok If unused keep pins open PCM_IN PCM output signals are tri stated when there is not an PCM_SYNC active SCO or eSCO 3 3 2 6 General Purpose I O and ADC See 3 3 2 2 39 3 3 2 7 Miscellaneous USB D Vimax 0 3vdd_usb Normally inactive Pull to GND Vimin 0 7vdd_usb through 10k USB D Vitmax 0 3vdd_usb Normally inactive Pull to GND Vmin 0 7vdd_usb ATOS DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 7 2007 8 EZURiO Ltd www EZURiO com Vimax 0 9V Active HIGH The Reset input Vamin 2 1V contains a 10kQ pull down resistor to ground Terminology USB Signal Levels vdd_usb refers to the internal voltage generated by the LDO regulator on the module which is typically 3 0V Hence 0 3vdd_usb and 0 7vdd_usb correspond to 0 9V to 2 1V If Vcc falls below the recommended minimum of 3 3V these values will be reduced 4 I O Characteristics 4 1 Power Consumption The current drain from the Vcc power input line is dependent on various factors The three most significant factors are the voltage level at Vcc UART Baudrate and the operating mode The hardware specification for the Module allows for a voltage range of 3 3 to 5 0 at Vcc The unit includes a linear regulator and tests have shown that there is no significant difference in cur
12. supplied in a small form factor pcb 22 0mm x 34 0mm x 7 6mm that connects to a main pcb using a 40 way Hirose connector The interface is compatible with the BISM1 module and EZURiO s 40 pin 802 11 modules The BISM II PA module is Lead free and is RoHS compliant and supports an industrial temperature range of 10 C to 85 C A key feature of the design is that the module is pin and format compatible with EZURiO s range of 802 11 wireless LAN modules This allows designers to manufacture a single version of pcb which can accept either a Bluetooth or an 802 11 module greatly reducing development time to generate a range of wirelessly enabled products The compatible 802 11 modules are the WISMCO1 which contains a full TCP IP stack network drivers and a web server and the WISMCO2 which contains wireless network drivers and a UDP stack with SLIP interface DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 1 2007 8 EZURIiO Ltd www EZURiO com 1 1 Applications e POS Equipment e Voice Applications e Medical Equipment e Industrial Automation e Telematics e Automotive Applications 2 Features Feature Implementation Standards Supported Bluetooth v2 0 Transmit Class Class 1 Frequency 2 400 2 4835 GHz Channels 79 channels Frequency Hopping Adaptive Frequency Hopping Max Transmit Power 18 dBmi from integrated antenna 16 dBm antenna connector option Min Transmit Power 27 dBmi from integrated antenna Receive Sensitiv
13. the manufacturer is a member of the Bluetooth SIG Membership of the Bluetooth SIG is free and application can be made at www bluetooth org 12 3 2 FCC and Industry Canada Statements This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment To inherit the modular approval the antennas for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter Co location with other radio transmitting devices operating concurrently in the same band will require additional testing and certification DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 25 2007 8 EZURiO Ltd www EZURiO com Designers should note the distinction that the FCC makes regarding portable and mobile devices Mobile devices are defined as products that are not used closer than 20cm to the human body whereas portable devices can be used closer that 20cm to the body In the case where the WISM module is used in a portable device additional SAR testing must be performed on the complete product
14. to incorporate these guidelines into all manuals supplied with the product Failure to comply with these precautions violates safety standards of design manufacture and intended use of the product EZURiO assumes no liability for customer failure to comply with these precautions 12 2 Safety Information If the Bluetooth module is used in equipment that might be taken and operated on a commercial flight the following safety instructions or similar warning should be added to the user manual Switch off the Wireless device before boarding an aircraft Make sure it cannot be switched on inadvertently The operation of wireless appliances in an aircraft is forbidden by many airlines to prevent interference with communications systems 12 3 Certifications 12 3 1 Bluetooth Qualification This device has been tested according to the Bluetooth Qualification program and approved as an END product with Bluetooth approval number BOxxx END product approval means that integrators do not need to perform any further Bluetooth approvals unless additional profiles are added within their specific product To meet the requirements of the Bluetooth SIG this approval number must be marked on the final equipment or referenced in the accompanying documentation The use of the Bluetooth logo on a product or any associated material is controlled by the Bluetooth Brand Book Usage is freely allowed for devices incorporating this END product module so long as
15. www EZURiO com 10 5 1 Fixing Pillars EZURiO in conjunction with Richco has designed a mounting pillar for use with the Bluetooth Serial Module This allows the module to be securely held to a primary pcb using snap fit details A variety of different heights are available to accommodate different variants of Hirose stacked connectors Pillars supporting a 3 5mm stacked board height can be supplied by EZURiO These and alternative Spacings can also be ordered directly from Richco Customer designs using these pillars should use 2 5mm diameter holes on a 1 6mm thick PCB in conjunction with the 3 3 mm stacked height Hirose if they are to take advantage of this Board Spacing Part number Matching HRS PCB Socket NPR2005 153 3 3 EZURiO Richco CL537 0032 4 86 NPR2005 153 4 1 CL537 0057 5 86 NPR2005 153 5 1 CL537 0157 0 86 See http wWww hirose co jp cataloge hp e53700036 pdf for detail information on the PCB socket DSH _BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 23 2007 8 EZURiO Ltd www EZURiO com 11 Board to Board Connector This chapter provides specifications for the 40 pin board to board connector which serves as physical interface to the host application The receptacle assembled on the Module is Hirose type DF12C Details are available at http www hirose co jp cataloge_hp e53700036 pdf 11 1 Stacking Height Mating headers from Hirose are available in different stacking heights allowing the spacing between the BISM II
16. 0 Upgradeable for Bluetooth 2 1 when available Simple AT style programming interface Audio codec evaluation kits available 802 11b g Enhanced drivers for low power operation Robust TCP IP stack Integrated Web Server Embedded interpreter UWScript for fast development A range of codec audio development boards see Section 6 1 4 2 are available These can be plugged into the wireless development kit for rapid of audio applications For cellular applications the Wireless Development Kit also supports Siemens MC55 range of GSM GPRS modules which are pin compatible with EZURiO s wireless LAN module This permits DSH _BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 30 2007 8 EZURiO Ltd www EZURiO com designers to develop products which can support either short range or wide area wireless connectivity with incredibly fast time to market 17 nterchangeable 802 11 Module EZURiO s range of Wireless LAN modules have been designed to be physically interchangeable with the BTM402 Bluetooth module and the BISM Bluetooth Serial Module For product designers this means that they can design a single pcb which can be populated with either an 802 11 or Bluetooth module giving the opportunity to launch two different variants of wireless connectivity at minimal additional engineering effort The WISMCO1 802 11b g TCP IP Wireless LAN Module is a fully integrated and qualified wireless device server designed to make it simple to embed 80
17. 2 11 connectivity Unlike other wireless modules all of the necessary drivers protocol stack security algorithms and antenna are integrated The module also includes an interpreter that can run scripts providing a complete wireless processing solution It enables you to add wireless internet connectivity to almost any device with a serial port The module is designed for lowest cost of integration and ownership It is ideal for enabling M2M applications The module is a dual processor design dedicating one processor to the 802 11b g baseband with a second powerful ARM7 processor with 16MB of SRAM and 64MB of flash memory running the wireless drivers TCP IP stack web server and UWScript interpreter Connection to the host device is via a high speed 921 600 bps UART with an additional twelve GPIO lines and two 10 bit ADCs The interpreter allows complex scripts to be run allowing the WISM module to operate with zero host loading It means it is possible to use the module to wirelessly enable dumb sensors or UART ports 18 Disclaimers EZURIO S BLUETOOTH PRODUCTS ARE NOT AUTHORISED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE MANAGING DIRECTOR OF EZURIO LTD The definitions used herein are a Life support devices or systems are devices which 1 are intended for surgical implant into the body or 2 Support or sustain life and whose failure to perform when properl
18. 3 UART Change the baud rate from 1200 to 921 600 baud Use the DSR line to drop connections Flexible configuration as either DTE or DCE Change escape sequence character Change the number of Stop bits and Parity Enable or disable echoes 7 3 1 4 Security Enable Authentication by requiring a PIN code for incoming AND OR outgoing connections Enable data to be encrypted over the air for incoming AND OR outgoing connections The module can be configured to be non connectable and non discoverable non connectable but discoverable connectable but non discoverable connectable and discoverable Automatically store Paired devices in a trusted device database in the flash memory 7 3 1 5 Bluetooth Set the module to be a master or slave Make a Bluetooth connection to a specified device Perform a full inquiry for other Bluetooth devices Query a remote device to check if a service is offered Fetch the friendly name of a remote device Increase or decrease the delay before the master abandons a connection attempt Change the device class code Set the device s friendly name Change the Inquiry scan time Change number of returned devices from an inquiry scan Obtain the RSSI value for a connection 7 3 1 6 Power Management Decrease or increase the output power to suit your connection range Configure the modules to work in Sniff and other low power modes DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 13 2007 8 EZURiO Ltd
19. 7 8 EZURiO Ltd www EZURiO com 15 Related Documents e The firmware incorporated into the BTM402 Bluetooth Module is the same as that for the BISM2 Module All of the firmware documentation and application data for the BISM2 module can be used for this module e blu2i AT Command Set Reference Manual e blu2i Firmware Release Notes e blu2i Multipoint Firmware Reference Manual e Intelligent Bluetooth Serial Module Quick Start Guide e Intelligent Bluetooth Serial Module FAQ e Wireless Developer s Kit User Guide e ACC 005 Winbond W61360 Audio Codec Board Manual e ACC 006 OKI 7702 Audio Codec Board Manual e ACC 007 OKI 7705 Multi channel Audio Codec Board Manual e ANO15 Use of External Antenna with Wireless Modules e ANO16 Notification Requirements for Wireless Products e blu2i Application Scenarios e Bluetooth Core 2 0 Specification www Bluetooth org 16 Development Kit EZURiO offers a Wireless Development Kit for embedded developers which is unique in supporting Bluetooth 802 11 and GSM GPRS It provides a simple design environment that can dramatically reduce the development time of wirelessly enabled products The Wireless Development Kit is available with EZURiO s pre qualified Bluetooth and 802 11 Wireless LAN modules Both modules contain embedded protocol stacks removing the need for complex programming on a host processor Features Bluetooth Complete qualified Bluetooth stack Support for Version 2
20. I PA module may be able to simplify their power supply circuitry as a result 10 4 RF Shield To meet FCC requirements all modules are supplied with a soldered RF shield This meets the requirement that users may not be able to access RF circuitry without special tools Removal of the Shield will negate RF approvals 10 5 Mounting the Module onto the application platform There are many ways to properly install the Module in the host device An efficient approach is to mount the PCB to a frame plate rack or chassis Fasteners can be M1 8 or M2 screws plus suitable washers circuit board spacers or customized screws clamps or brackets in 2 2mm diameter holes Note that care should be taken to ensure the head of the fixing does not interfere with the circuit Nylon fixings are recommended In addition the board to board connection can also be utilized to achieve better support The antenna Brown square component on top side of PCB must not be influenced by any other PCBs components or by the housing of the host device The proximity of the antenna to large metallic objects can affect the range and performance of the system Designers should carefully consider the location of the Module and the type of enclosure material that is used To prevent mechanical damage be careful not to force bend or twist the Module Be sure it is positioned flat against the host device DSH _BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 22 2007 8 EZURiO Ltd
21. Transmit Power max 40mW 16dBm Antenna Gain 2dBi typ Effective Transmit Power Max 65mW 18dBmi Output power can be reduced by program control 5 1 2 Receive Sensitivity Receive Sensitivity 85dBm at 25 C Antenna Gain 2dBi typ Effective Receive Sensitivity 87dBm at 25 C 6 Functional Description The BISM II PA Bluetooth module is a self contained Bluetooth product and requires only power to implement full Bluetooth communication The integrated high performance antenna together with the RF and Base band circuitry provides the Bluetooth wireless link and the UART interface provides a connection to the host system The variety of interfaces and the AT command set allow the BISM II PA module to be used for a wide number of short range wireless applications from simple cable replacement to complex multipoint applications where multiple radio links are active at the same time The complexity and flexibility of configuration are made simple for the design engineer by the integration of a extremely comprehensive set of AT commands supplemented with a range of S registers which are used for non volatile storage of system parameters These are fully documented in the Blu2i AT Command Reference Manual To provide the widest scope for integration a range of different physical host interfaces are provided 6 1 Interfaces 6 1 1 UART interface UART_TX UART_RX UART_RTS and UART_CTS form a conventional as
22. ale lease maintenance use performance failure or interruption of these products Bluetooth is a trademark owned by Bluetooth SIG Inc USA and is licensed to EZURiO Ltd DSH _BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 32 2007 8 EZURiO Ltd Mouser Electronics Authorized Distributor Click to View Pricing Inventory Delivery amp Lifecycle Information Laird Technologies BTM404
23. ation receives data from the module s UART_TX signal line Application Serial Module UART_TX UART_RX UART_CTS UART_RTS UART_DSR Cc gt J cr Oo mn an O Q UART_DTR D9BJISJUI ZEZSY UART_RI i UART_DCD Note that the serial module output is at 3 0V CMOS logic levels Level conversion must be added to interface with an RS 232 level compliant interface 6 1 2 SPI bus The Module is a slave device that uses terminals SPI_MOSI SPI_MISO SPI_CLK and SPI_CSB This interface is used for program firmware updates at the factory EZURIiO supply a PC based utility to allow firmware upgrade over the UART port It is highly recommended that customers should use this method for updating firmware Note The designer should be aware that no security protection is built into the hardware or firmware associated with this port so the terminals should not be permanentl y connected in a PC application 6 1 3 GPIO Port Seven lines of programmable bi directional input outputs I O are provided that can be accessed either via the UART port or Over The Air OTA from a second Bluetooth unit These can be used as data inputs or to control external equipment By using these in OTA mode a BISM module can be used for control and data acquisition without the need for any additional host processor Each of the GPIO 3 9 ports can be independently configured to be either an Input or Output A selection of ports
24. can be remotely controlled by a master unit see register S536 This places the slave unit s AT parser in remote mode providing over the air configuration This mode is of use for remote sensor applications where no host processor is required to control the slave Bluetooth unit 7 6 Boot modes The module has the capability of booting into 1 of 7 modes Currently only Boot Mode 1 is supported Boot Mode 1 is default and gives functionality equivalent to the BISM1 module These modes will specify different PSKEY settings to allow for different basic operation Please contact EZURiO for further information 8 Low Power Modes The current drain from the Vcc power input line is dependent on various factors The three most Significant factors are the voltage level at Vcc UART baud rate and the operating mode The hardware specification for the PA module allows for a normal operating voltage range of 3 3V to 5 0V The UART baud rate has a bearing on power drain because as is normal for digital electronics the power requirements increase linearly with increasing clocking frequencies Hence higher baud rates result in a higher current drain Finally with regards to operating mode the significant modes are idle waiting for a connection inquiring initiating a connection and connected With connected mode it is also relevant to differentiate between no data being transferred and when data is being transferred at the maximum rate possible
25. details on the notification procedure are given in EZURiO s Application Note ANO16 Notification Requirements for Wireless Products DSH _BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 26 2007 8 EZURiO Ltd www EZURiO com 13 Environmental 13 1 Operating temperatures CE Mn yp ax TS 13 2 Storage temperature Parameter mm ax CT 13 3 Reliability Parameter Test Comment Thermal Shock 200 cycles 200C 65 C 30 min 1 cycle hour Vibration Continuous operation at 60 Hz 15g max sine wave 12 hours 2mm stroke M a Con Temp Storage 8006 0 mou Lou Temp Storage 20 C 240 neue High Temp Humidity 60 C 90 RH 360 hours Operation Thermal shock 20 to 60 C in 30min 200 cycles with continuous operation Electro Static Discharge EN55024 1998 amp IEC61000 4 3 Drop Test 75cm to concrete 3 axis x 2 cycles per corner DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 27 2007 8 EZURiO Ltd www EZURiO com 14 Physical Dimensions 14 1 Mechanical Dimensions 14 1 1 Standard Module 4 3 _ ft 22 840 20 13 Max c9 o D T N o o bs a co 0 LO oo i o o ip N O o O D o o oo Wa 2 4 M a Q Le MaX A FR D 7 2 940 05 _ 7 Te 2 5 REF 1 7 1740 05 z f Len 20 4 i ve Location of Connector Bottom View All dimensions in mm 928 440 05 Note that there are components on the underside of the pcb See section 3 1 fo
26. econds Then the duty cycle can be varied by changing the value of S Registers 509 and 511 appropriately For example if S Register 508 and 510 are both set to 1000ms and S Register 509 and 511 are both set to 1ims then the duty cycle is reduced to 1 this means that average current drain at 5 0v will be 2 of 65mA plus the normal idle mode current that is it is as low as 2 75mA However in this case it can take up to 1 second to establish a connection The connected state current consumption while a master or slave can be considerably reduced by enabling Sniff mode described in detail in the next section When a Bluetooth connection has been made the units in the connection will use internal measurements of the signal quality to implement power control reducing the transmit power at each end of the link to a level sufficient to maintain the connection For this reason power consumption will vary with range 8 1 Low Power Modes using Sniff Bluetooth connections are master slave in nature master sends packets and a slave has to acknowledge that packet in the next timeslot Timeslots in Bluetooth are 625 microseconds wide This implies that a master will always know when packets will be sent and received which further means it is able to optimise power usage by switching on power hungry circuitry only when needed A slave on the other hand does NOT have prior knowledge of when a packet will be received and has to assume that a packet
27. efault configuration is as an input xxx Pins 2 and 4 were used as GPIO in previous versions of the BISM and WISM These signals are used internally for PA control These pins MUST NOT BE CONNECTED PIO lines can be configured through software to be either inputs or outputs with weak or strong pull ups or pull downs At reset all PIO lines are configured as inputs with weak pull downs UART_RX UART_TX UART_CTS UART_RTS UART_RI UART_DCD and UART_DSR are all 3 0v level logic For example when RX and TX are idle they will be sitting at 3 0V Conversely for handshaking pins CTS RTS RI DCD DSR a Ov is treated as an assertion DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 5 2007 8 EZURIO Ltd www EZURiO com Pin 6 UART_RI is active low It is normally 3 0v When a remote device initiates a connection this pin goes low This means that when this pin is converted to RS232 voltage levels it will have the correct voltage level for assertion Pin 8 UART_DCD is active low It is normally 3 0v When a connection is live this pin is low This means that when this pin is converted to RS232 voltage levels it will have the correct voltage level for assertion Pin 10 UART_DSR is an input with active low logic It should be connected to the DTR output of the host When the BISM II PA Module is in high speed mode See definition for S Register 507 this pin Should be asserted by the host to ensure that the connection is maintained A deassert
28. es attached to it with all slaves having requested varying sniff parameters It may therefore be impossible to guarantee that each slave gets the M parameter it requested In light of this the protocol for enabling sniff mode specifies that a requesting peer specify the M parameter as a minimum and maximum value This will allow the master to interleave the sniff modes for all slaves attached For this reason the sniff parameters are specified in the BISM II PA module via four S registers S Register 561 is used to specify N S Register 562 is used to specify T and S Registers 563 564 are used to specify minimum M and maximum M respectively Although the specification defines these parameters in terms of timeslots the S register values have to be specified in units of milliseconds and the firmware does the necessary translation to timeslots DSH_BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 15 2007 8 EZURiO Ltd www EZURiO com Low Power Consumption Data Exchange Data Exchange T Slots Data Exchange Data Exchange Data Exchange T Slots T Slots T Slots M Slots Negotiated M Slots Negotiated DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 16 2007 8 EZURiO Ltd www EZURiO com 9 Application Examples 9 1 RS232 Modem Signals A serial port has DTR DSR RTS CTS DCD and RI control lines RTS and CTS are locally controlled to prevent local buffer
29. ion is taken to mean that the connection should be dropped or an online command mode is being requested Pin 27 VCC_3V0O monitor may only be used for monitoring purposes It must not be used as a current source The GPIO pins can be accessed using S Registers 621 to 628 GPIO3 is also used for DTR output active low See S Register 552 amp 553 Analogue O and 1 should not exceed 1 8v and S Registers 701 and 702 are used to access them 3 3 Electrical Specifications 3 3 1 Absolute Maximum ratings Absolute maximum ratings for supply voltage and voltages on digital and analogue pins of the Module are listed below exceeding these values will cause permanent damage Parameter Peak current of power supply Voltage at digital pins Voltage at POWER pin 3 3 2 Recommended Operating Parameters 3 3 2 1 Power Supply GND 11 15 18 6 Ground terminals to be attached 30 36 38 in parallel VCC_3V0 27 3 0V typical For monitoring only No current source 3 3 2 2 Signal Levels for Interface PCM SPI and GPIO Signal Type Signal level Signal level OmA load Vitmin 0 4V V max 0 8V Vipmin 2 1V Vipnmax 3 4V Output Vo_max 0 2V Vonmin 2 8V DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 6 2007 8 EZURiO Ltd www EZURiO com 3 3 2 3 RS 232 Interface Signal Name PinNo 1 0 Comments UART_TX 21 UART_RX 25 UART_DTR P Shared with GPIO3 UART_RI ETN Direction may be programmed UART_DCD 8 IorO Direction may be
30. ipment If during the warranty period any component part of the equipment becomes defective by reason of material or workmanship and EZURiO is immediately notified of such defect EZURiO shall at its option supply a replacement part or request return of equipment freight prepaid to its designated facility for repair In the event no trouble is found on products returned for repair EZURiO reserves the right to charge the customer its standard published repair charge This warranty shall not apply to any products that have been subject to misuse bending twisting neglect alteration improper installation testing or unauthorized repair performed by anyone other than a EZURiO designated repair facility Any non warranty repairs or maintenance shall be at EZURiO s standard rates in effect at the time This warranty is in lieu of all other warranties whether expressed implied or statutory including but not limited to implied warranties or merchantability and fitness for a particular purpose In no event shall EZURiO be liable whether in contract in part or on any other basis for any damage sustained by its customers or any other person arising from or related to loss of use failure or interruption in the operation of any products or delay in maintenance or for incidental consequential in direct or special damages or liabilities or for loss of revenue loss of business or other financial loss arising out of or in connection with the s
31. ity 87 dBm Data Transfer rate Up to 300kbps Range Up to 1 000 metres free space Integrated Antenna High performance 2dBi multilayer ceramic External Antenna option 50 Ohm U FL connection Serial Interface RS 232 bi directional for commands and data 16550 compatible Baud Rate Configurable from 1 200 to 921 600bps Non standard baud rates supported Bits 7 or8 Parity Odd even none Stop bits 1 or 2 Default Serial parameters 9 600 n 8 1 Levels 3 0V CMOS Modem Control DTR DSR DCD RI RTS CTS debi Purpose Interface 7 general purpose I O pins 3 0V cmos 2 ADC inputs 8 bit 1 8V max Support 3 PCM Channels 64kbps SCO Channels Support SCO and eSCO PCM Interface Configurable as master or slave 8 bit A law 8 bit law 13 bit linear PCM Clock available when in slave mode DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 2 2007 8 EZURIiO Ltd www EZURiO com Protocols amp Firmware Bluetooth Stack V2 0 compliant Fully integrated Profiles GAP Generic Access Profile SDP Service Discovery Profile SPP Serial Port Profile FTP Client Advertised Profiles DUN Dial Up Networking FTP Server Headset Audio Gateway Handsfree Audio Gateway Profile Components Audio Gateway Generic OBEX Push Pull Client Firmware Upgrade Available over UART Connection Modes Point to point cable replacement Multipoint max 7 slaves Command Interface AT Instructions set Comprehensive control of connection and module
32. lt bdaddr_m gt and that of the slave to be lt bdaddr_s gt the master module is configured by sending it the following AT commands AT amp F ATS512 1 ATS504 1 ATS507 2 ATS530 2000 AT amp W AT BTR lt bdaddr_s gt DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 18 2007 8 EZURiO Ltd www EZURiO com The ATS507 2 setting puts the device in DSR drop mode only This means that when the device needs to be reconfigured deasserting the DSR line will ensure that the module responds quickly to AT commands This further means that in stand alone mode the DSR input line MUST be asserted e g OV in TTL signal mode The slave is configured by AT amp F ATS512 4 ATSO 1 AT amp W AT BTR lt bdaddr_m gt Where lt bdaddr_m gt is optional If it is not specified then the slave unit will accept connections from any device If specified then only connections from the device specified will be accepted If it is desired that the slave unit should not be discoverable the master is by default not discoverable then the configuration commands are AT amp F ATS512 3 ATSO 1 AT amp W AT BTR lt bdaddr_m gt Where lt bdaddr_m gt is optional If it is not specified then the slave unit will accept connections from any device If specified then only connections from the device specified will be accepted When the units are next power cycled the slave unit will wait for the master to connect to it and the master will continually look fo
33. ng This is a cosmetic effect and does not affect the RF performance DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 21 2007 8 EZURIO Ltd www EZURiO com 10 2 Power Supply Considerations The power supply for the Module should be a single voltage source of Vcc within the range of 3 3 V to 5 0 V It must be able to provide sufficient current in a transmit burst This can rise to 200mA To limit dissipation it is recommended that a voltage at the lower end of the range is used The Module includes regulators to provide local 3 0V This rail is accessible on connector J2 for monitoring purposes only Under no circumstances should this pin be used to source current Power Vcc to the module is provided via the board to board connector Pin 29 on J2 10 3 Power On Reset Power Cycling and Brown Out considerations The Module is provided with an active high reset pin Hirose 40way DF12C connector pin 13 Upon the application of power the Power On Reset circuit built into the Module will ensure that the unit starts correctly There is no need for an external power reset monitor Note The previous version of the Bluetooth Serial Module required an external Brown Out circuit to ensure correct operation This circuitry has now been incorporated into the module The power supply has been designed to work with previous versions of customer circuitry that may or may not have external brown out implementations Customers migrating from a BISM1 to BISM I
34. operation S Registers for non volatile storage of parameters Multipoint Software Supports multiple connections Current Consumption Data Transfer Typically 130mA Low Power Sniff Mode Less than 2 5mA Supply Voltage Supply 3 3V 5 0V DC Regulation On board regulators and brown out detection Coexistence Compatibility WLAN 802 11 2 wire and 3 wire hardware coexistence schemes supported Pin compatible with EZURiO WISM Bluetooth modules Connections Interface 40 way Hirose DF 12 Connector External Antenna option U FL connector for 50 Ohm antenna Physical Dimensions 22 8mm x 33 8mm x 7 6mm Weight 8 grams Operating Temperature Continuous transmission 10 C to 85 C Storage Temperature 40 C to 85 C Approvals Bluetooth Qualified as an END product BOxxxx FCC Modular Approval PI409B IC Industry Canada 1931B BISMPA33 CE amp R amp TTE Approved Lead free Lead free and RoHS compliant Warranty 2 Years Development Tools Development Kit Development board and software tools DSR DTR RI and DCD are configurable either as GPIO or as modem control lines DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 3 2007 8 EZURIO Ltd www EZURiO com 3 Functional Block Diagram Ceramic Patch a s Eb Sain 3 Antenna lt RX Tx Rx Switch Vaan jee Lake 8 d F i d a 7 f K f i il R LE M ba lash DTR can be confi gured as a seventh GPIO 3 1 Interconnection The Module is eq
35. overflow The status of DTR DRS DCD and RI can be exchanged with the remote peer device If for example the DTR DSR lines are to be exchanged between the two peers to simulate the performance of a physical cable then it is possible to do so Refer to the description for S Registers 551 552 and 553 for more details Just as a telephony modem has control and status lines the Module also provides for 6 control and Status lines as per the table below The direction column is as seen from the module s viewpoint IN or OUT RI also known as CI Ring Indicate IN or OUT DCD Data Carrier Detect DSR Data Set ready DTR Data Terminal Ready IN CTS Clear to Send RTS Request to Send configurable with S register 552 The first four lines are under program control These use four of the GPIO pins and are mapped to I O as per the table below The last two are under control of the UART driver and their functionality is always enabled Connector Pin Label Function IN OUT GPIO3 UART_DTR Some serial implementations link CTS and RTS to remove the need for handshaking EZURiO do not recommend linking CTS and RTS other than for testing and prototyping If these pins are linked and the host sends data at the point that the Bluetooth Serial Module deasserts its RTS signal then there is a significant risk that internal receive buffers will overflow which could lead to an internal processor crash This will lead to a drop in
36. r details DSH _BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 28 2007 8 EZURiO Ltd www EZURiO com 14 2 BISM II PA Module without antenna special order The dimensions for this module are identical to the standard BISM II PA illustrated above but the antenna is replaced with a U FL connector The external antenna must provide a 50 Ohm impedance The external antenna used must not result in an increased output power I e the total gain of mating connector cable and antenna must not exceed 2dB If a higher gain antenna is connected it will invalidate Bluetooth approvals for the module as well as national RF compliance Any change of antenna may require retesting of the RF performance to ensure that compliance is not affected This is covered in more detail in application note ANO15 Use of External Antenna with Wireless Modules The antenna connector is a U FL connector supplied by Hirose Mating connectors with cables are available from Hirose and their distributors and also from other cable suppliers The data sheet for the connector series is available at http www hirose co jp cataloge hp e32119372 pdf 14 3 Labelling The label contains the Part number and the unique Bluetooth address of the module 14 4 Ordering Information The Bluetooth PA Module described in this data sheet should be ordered using the part number below BTM404 3 3V Bluetooth PA Module with Antenna DSH _BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 29 200
37. r the slave If a connection attempt fails the master will wait for 2 seconds before reattempting a connection This 2 second delay can be varied by issuing it an ATS530 command with an appropriate value in the range 100ms to 15000ms IMPORTANT NOTE The DSR input to the module MUST be asserted for the auto connection to succeed When operating at TTL levels a low OV is seen as an assert state When operating at RS232 levels any voltage greater than 2 1V is seen as assert It is usual to connect the DTR line of the host to the DSR line of this device 9 4 Audio Cable voice With a pair of these modules it is possible to replace a mono audio cable with two way traffic That is a setup where a microphone is connected to a speaker at the remote end and vice versa So this mode effectively replaces two audio cables Assuming the Bluetooth address of the master to be lt bdaddr_m gt and that of the slave to be lt bdaddr_s gt the master module is configured by sending it the following AT commands AT amp F ATS512 1 ATS504 1 ATS530 2000 ATS532 7 AT amp W AT BTR lt bdaddr_s gt And the slave is configured by AT amp F DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 19 2007 8 EZURiO Ltd www EZURiO com ATS512 4 ATSO 1 AT amp W AT BTR lt bdaddr_m gt 9 5 Oscillator Output The output from the high performance crystal oscillator 10ppm can be divided and output on one of the selected PIO lines removing the need for a
38. rent draw when Vcc changes within the operating limits Tests have shown that where power dissipation is an issue it is best to keep Vcc at the lower end of the range The UART baudrate has a bearing on power dissipation because as is normal for digital electronics the power requirements increase linearly with increasing clocking frequencies Hence higher baudrates result in a higher current drain Finally with regards to operating mode the significant modes are idle waiting for a connection inquiring initiating a connection sniff and connected With connected mode it is also relevant to differentiate between no data being transferred and when data is being transferred at the maximum rate possible The AT command Set document describes how to configure the Module for optimal power performance 4 1 1 Typical Current Consumption in mA Vcc 4 1V Baudrate 115 200 bps Current mA Range 10 metres Idle Mode S512 1 Ul Wait for Connection Or Discoverable Mode AT BTP S508 S510 640 S509 S511 320 Wait for Connection Or Discoverable Mode AT BTP S508 S510 1000 S509 S511 11 Inquiry Mode AT BTI Connecting Mode ATDxxx 129 Connected Mode No Data Transfer Connected Mode Max Data Transfer See section 8 for details of different low power modes DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 8 2007 8 EZURiO Ltd www EZURiO com 5 RF Performance 5 1 1 Transmit Power Conducted
39. scovery Profile SDAP Serial Port Profile SPP Dial Up Networking Profile DUN Headset Profile HSP Hands Free Profile HFP File Transfer Profile FTP and OBEX Client A virtual processor is used within the BC04 to implement an AT command processor This interfaces to the host system over a straight forward serial port using an extensive range of AT commands The AT command set abstracts the Bluetooth protocol from the host application saving many months of programming and integration time It provides extremely short integration times for data oriented cable replacement and voice applications Firmware is also included that provides programming Support for multi point applications A low cost development system is available for fast product evaluation and development Support is provided for low power modes that make the BISM II PA particularly applicable to battery powered installations The Module can be configured so that it can be attached to a dumb terminal or attached to a PC or PDA for cable replacement applications In addition to the Bluetooth functionality The BISM II PA Module provides access to 7 General I O lines and 2 analogue input lines These can be configured to provide connection to simple devices such as switches or LEDs without requiring any external processor Both the GPIO and ADC lines can be accessed either via the wired host UART connection or remotely over the Bluetooth link The BISM II PA module is
40. th functionality can be covered greatly reducing development time To provide additional functionality a range of S registers has been implemented These allow program settings to be stored to control the BISM II PA function and also give access to configuring and reading ports and status registers within the BISM II PA Full details of the AT command set are provided in the Blu2i AT Command Reference Manual 7 3 1 AT features at a glance 7 3 1 1 General e Configure two modules to automatically connect and transfer data audio or a combination of data and audio when both devices are powered The peer device does not have to be another Intelligent Serial Module It is possible to implement auto connect with a Bluetooth enabled mobile phone e Automatically re connect devices when a connection is dropped DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 12 2007 8 EZURiO Ltd www EZURiO com Remotely access the AT parser of the remote unit from a master device to perform Over The Air OTA configuration Configure the module to enter a state on power up and after a period of time change to another state automatically This allows units to be placed in the discoverable state for a limited time period Read and write to GPIO lines Read the ADC channels Get fast GPIO and ADC status through an inquiry response patent pending 7 3 1 2 Audio Set up audio connections Enable disable Auto Answer for incoming connections 7 3 1
41. these different applications the Bluetooth SIG Special Interest Group has defined a series of different profiles that define the way in which Bluetooth devices communicate with each other and perform basic functions These provide a base line of interoperability for specific application scenarios upon which more complex user applications can be developed There are over 30 different profiles many of which have been developed for specific applications The BISM II PA firmware is provided with support for the profiles that are most commonly required for cable replacement applications The current profiles supported by the AT command set firmware point to point applications include DSH_BTM404_Ov5 BISM2 3V3 PA Data Sheet DOC 11 2007 8 EZURiO Ltd www EZURiO com e GAP Generic Access Profile The base connection profile upon which others are based e SDP Service Discovery Profile The profile to find other Bluetooth devices and the services they support e SPP Serial Port Profile Emulation of a serial cable for cable replacement applications e FIP File Transfer Profile Client Generic OBEX push and pull functionality is available as a part of FTP Client support The following profiles can be advertised by the module This allows the user application to implement the required interactive portion of the profile in an external host processor e DUN Dial Up Networking Profile support for connection to an external PSTN GSM GPRS or VPN
42. uipped with a 40 pin 0 5mm pitch board to board connector that connects to the application platform Note that the underside connector side of the pcb contains a number of components Sufficient clearance must be maintained on the mating pcb to guarantee clearance Q H e a BISPA 01 R 100 02 EZURIO 2005 C EZURIO LTD 2006 A o Ces co DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 4 2007 8 EZURIO Ltd www EZURiO com 3 2 Pin Descriptions The Hirose DF12C board to board connector on the module is a 40 pin double row receptacle The table below defines the pin functions Note that this pin out is as viewed from the underside of the Module Analogue 1 1 8v Max Do not connect gt EEE seis sonarom a oe fo emeu former a PS 1s reser Reset P sfa sfo RE Ro roma romo 22 eomm emoe Rs PeMour rmmmor pafwe wofa S ape oo GPIO7 I O for Host Gr orice don 3s oroo morrn Notes The reset circuitry within the BISM Serial Modules now incorporates a brown out detector within the module Customers migrating from previous modules should check their implementation as they may be able to simplify their external power supply design The reset line has a fixed 10kOhm pull down resistor to ground Pins 33 35 and 37 were N C on BISM1 Pin 39 was a 1V8 monitor Designers migrating between designs should be aware that these are now available as I O D
43. will be received from a master on every receive slot This means that it has to leave its receiving circuitry on for most of the receive slot duration This problem was identified very early in the evolution of Bluetooth especially since headsets spend all their time as a slave ina Bluetooth connection and it was solved by having a mode called Sniff with appropriate lower layer negotiating protocol Sniff mode during connection is basically an agreement between the slave and its master that data packets will only be exchanged for N timeslots every M slots The slave can then assume that it will never be contacted during N M slots and so can switch its power hungry circuitry off The specification goes further by also specifying a third parameter called timeout T which specifies extra timeslots that the slave will agree to listen for after receiving a valid data packet Put another way if a data packet is received by the slave then it knows that it MUST carry on listening for at least T more slots If within that T slot time period another data packet is received then the timer is restarted This mechanism ensures low power consumption when there is no data transfer at the expense of latency When there is a lot of data to be transferred it acts as if sniff mode were not enabled It is stated above that during sniff mode a slave listens for N slots every M slots The Bluetooth specification states that a master can have up to 7 slav
44. www EZURiO com a unit of EZURIO aid Long Range Bluetooth Serial Module 3 3V Bluetooth Module with Power Amplifier Part Number BT M404 1 General Description EZURiO s BISM II PA Bluetooth Serial Module is a fully integrated and qualified Class 1 Bluetooth solution which incorporates a power amplifier and low noise amplifier that maximises the RF link budget to provide the greatest range of any Bluetooth Module The module is designed for lowest cost of integration and ownership for designers wishing to incorporate Bluetooth functionality into their products The module is qualified to Bluetooth Version 2 0 The BISM II PA Bluetooth Serial Module is one of the most compact complete Bluetooth solutions making it ideal to integrate into handheld devices The module includes a high sensitivity high gain antenna which provides excellent range Typical open field performance provides ranges of up to 1 000 metres at transmit powers of 65mW The BISM II PA Module is based on Cambridge Silicon Radio s BlueCore 04 chipset The module contain all of the hardware and firmware for a complete Bluetooth solution requiring no further components The Module has an integrated high performance antenna which is matched with the Bluetooth RF and baseband circuitry The firmware integrated into the BCO4 chipset implements the higher layer Bluetooth protocol stack with support for applications requiring Generic Access Profile GAP Service Di
45. y used in accordance with the instructions for use provided in the labelling can reasonably be expected to result in a significant injury to the user b A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness EZURiO does not assume responsibility for use of any of the circuitry described no circuit patent licenses are implied and EZURiO reserves the right at any time to change without notice said circuitry and specifications 18 1 Data Sheet Status Preliminary Engineering Release EZURiO Ltd reserve the right to change the specification without notice in order to improve the design and supply the best possible product Please check with EZURiO Ltd for the most recent data before initiating or completing a design Where reference is made to related products from other suppliers EZURiO takes no responsibility for the information availability or performance of such products DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet DOC 31 2007 8 EZURIiO Ltd www EZURiO com 18 2 Warranty EZURiO warrants that its products shall conform to EZURiO s published specifications and remain free from defects in materials and workmanship under normal proper and intended use for a period of two 2 years from date of purchase provided that proof of purchase be furnished with any returned equ
46. ynchronous serial data port with handshaking The interface is designed to operate correctly when connected to other UART devices such as the 16550A The signalling levels are nominal OV and 3 0V and are inverted with respect to the signalling on an RS232 cable The interface is programmable over a variety of bit rates no even or odd parity stop bit and hardware flow control The default condition on power up is pre assigned in the external Flash Two way hardware flow control is implemented by UART_RTS and UART_CTS UART_RTS is an output and is active low UART_CTS is an input and is active low These signals operate according to normal industry convention By writing different values to the relevant S register the UART_RI can be continuously polled to detect incoming communication The UART_RI signal serves to indicate incoming calls UART_DSR is an active low input It should be connected to DTR output of the host When the module is running in high speed mode See definition for S Reg 507 this pin should be asserted by the host to ensure connection is maintained A de assertion is taken to mean that the connection should be dropped or an online command mode is being requested DSH_BTM404_O0v5 BISM2 3V3 PA Data Sheet DOC 9 2007 8 EZURiO Ltd www EZURiO com The module communicates with the customer application using the following signals Port TXD of the application sends data to the module s UART_RX signal line Port RXD of the applic
Download Pdf Manuals
Related Search