Mac - Compare Cellular
Contents
1. and User Manual 2 2 Software Installation 2 2 1 Insert the SIM Card into the Modem The SIM card is the Subscriber Interface Module provided by your Service Provider Before using the modem make sure the SIM card supports data services Insert the SIM card as shown with the gold contacts facing down and the beveled edge facing outwards of the device Push the SIM card in as far as it will go 2 2 2 Connecting the Modem and computer Before connecting the modem for the first time uninstall all previous versions of the software and reboot the computer Insert the modem into an available port on your computer Alternatively you may use the supplied USB cable to connect the modem to the computer In most cases the single cable should suffice However to increase the power delivered to the modem use the double USB cable if required 2 2 3 First Time Software Installation 1 Uninstall all previous versions of the USB Modem software and restart the computer 2 The installation program should launch automatically If this feature is disabled on your computer double click the Rogers Connection Manager CD drive that appears on your desktop and select Rogers Connection Manager 3 Press Continue on the welcome page 4 Select a destination to install the software on the volume Macintosh HD and then click Continue 5 Select Installation Type and then click Install 6 Please enter user name and password to be authenticated and left click OK t2. 1 USB Modem Introduction 1 1 Introduction Thank you for choosing the ZTE MF668 USB modem Please read this manual carefully and keep it for future reference The pictures symbols and contents in this manual are for reference only They are correct at the time of publication but might not be completely identical with your modem We operate a policy of continuous development We reserve the right to update the technical specifications in this document at any time without prior notice The HSPA modem is a multi mode 3G high speed modem suitable for GSM GPRS WCDMA EDGE HSDPA HSPA networks It uses the USB 2 0 standard interface for easy connection to any laptop or desktop computer It is compatible with 2G and 3G mobile networks allowing connection with wireless data and SMS services to give you high speed data access wherever you are 1 2 Safety Warning and Notice To the owner Some electronic devices are susceptible to electromagnetic interference The modem is a transmitting device and may cause interference to sensitive electronic equipment such as audio systems vehicle systems and medical equipment Please consult the manufacturer of the other device before using the modem Operating of a laptop or desktop computer with the modem may interfere with medical devices like hearing aids and pacemakers Please keep the modem more than 20 centimetres away from such medical devices Turn the modem off if necessary Consult a physicia
3. age After the message has been sent successfully the Text Message will be saved in the Sent Items If it fails to send it will be saved in the Draft box Send Text Messages while browsing the web You can send Text Messages when surfing on the Internet if your network operator supports this functionality 3 4 3 Text Message Interface Guide Enter Inbox Sent Items or Drafts to use the tabs at the bottom of the window Delete Delete the selected Text Message Reply Reply to the selected Text Message Edit Modify the message and or forward to other recipients SaveTo Save a copy of the message to the SIM or computer Notes New messages cannot be received when the SIM card is full Different SIM cards have different capacities The system will indicate if the SIM inbox is full Messages cannot be saved until some are deleted by the user New Text Messages will be saved to the SIM or computer based on the setting in Text Message Storage Location on the main messaging interface 3 5 Contacts Click the Contacts icon to switch to the Contacts interface Contact information can be saved on the computer or SIM card Each record includes Name Mobile Tel 1 Tel 2 Email and Group name Create a new contact Click below the contact area enter the contact information and select OK to finish Create a new group Click below the group area A new group will appear in the group list Double click on the g
4. ction The data amount time connected etc are displayed in the main window You can access the Internet and receive email by launching your usual applications Browser or Mail software Disconnect from the Internet When you are connected to the internet the Connect button changes to Disconnect Click Disconnect to end your session 3 4 Text Messages Click the Text Message icon to use access the messaging interface Inbox Stores the received text messages Sent Items Stores the successfully sent text messages Draft Saves any text messages not sent The drafts can only be saved on the computer New Compose a new message Notes Different SIM cards have different capacities For more information please consult your service provider 3 4 1 Read Text Messages Click the Inbox button to read the messages saved in the box You can use the buttons under the menu to Create New Reply Forward Delete and Save 3 4 2 Create New Message Click New and enter the recipient s number The recipient s number can be entered directly or by selecting entries from your Contacts Use a semicolon to separate multiple recipients Click into the text field to enter your message The Text Message content can be up to 160 characters long including symbols Messages longer than the maximum length will be divided into 160 character messages and sent separately to the recipient Click Send to send the mess
5. em There are no user serviceable parts inside the modem Unauthorised dismantling or repair of the modem will void the warranty 1 3 RF Safety Information The USB Wireless modem is a transmitting device with similar output power to a mobile phone It uses an internal antenna to connect to the mobile network To get the best performance from your device do not cover or shield the device in any way as this will lead to increased output power Always leave a clear space around the device to allow the transmit and receive signals to propagate It is not intended to be used as a handheld or body worn device but the SAR tests have been completed and exceed Canadian and US regulatory requirements Radio Frequency Energy Your handset is a low power radio transmitter and receiver When switched on it intermittently transmits radio frequency RF energy radio waves The transmit power level is optimized for best performance and automatically reduces when there is good quality reception Maximum power is only used at the edge of network coverage so under most circumstances the power output is very low Under poor network conditions the phone will transmit at a higher power may get hot and will have a significantly shorter battery life Declaration of Conformity THIS MODEL PHONE MEETS THE GOVERNMENT S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES Your wireless phone is a radio transmitter and receiver It is designed and manufactured not to exceed the em
6. ission limits for exposure to radio frequency RF energy set by the Federal Communications Commission of the U S Government These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population The guidelines are based on standards that were developed by independent scientific studies The standards include a substantial safety margin designed to assure the safety of all persons regardless of age and health The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate or SAR The SAR limit set by the FCC is 1 6W kg Tests for SAR are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands Although the SAR is determined at the highest certified power level the actual SAR level of the phone while operating can be well below the maximum value This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network In general the closer you are to wireless base station antenna the lower the power output Before a phone model is available for sale to the public in the public it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure The tests are performed in positions and locations as required b
7. ly according to predefined configuration rules and network status set by your service provider Manual User selects network settings 3 7 3 Check for Updates The Check for Updates button will direct you to a Rogers webpage where you can check the status of your software version and upgrade if necessary 3 8 Help Click the Help icon to switch to help interface 4 Declaration of RoHS Compliance To minimize the impact of our electronic devices in the global environment and take more responsibility and accountability in the growth of the mobile industry this document shall serve as formal declaration that the manufactured by ZTE CORPORATION is in compliance with the Directive 2002 95 EC of the European Parliament RoHS Restriction of Hazardous Substances with respect to the following substances 1 Lead Pb 2 Mercury Hg 3 Cadmium Cd 4 Hexavalent Chromium Cr VI 5 Polybrominated biphenyls PBB s 6 Polybrominated diphenyl ethers PBDE s This declaration is issued based on our current level of knowledge Since conditions of use are outside our control ZTE CORPORATION makes no warranties expressed or implied and assumes no liability in connection with the use of this information
8. n or the manufacturer of the medical device before using the modem near such devices Be aware of the regulations when using the modem at places such as oil warehouses or chemical factories where there are explosive gases or explosive products being processed Turn off your modem as instructed Don t touch the antenna area unnecessarily while connected This can affect your modem performance and reduce the signal quality Store the modem out of the reach of children The modem may cause injury or get damaged The modem contains sensitive electronic circuitry Do not expose the modem to any liquids high temperatures or shock Only use original accessories or accessories that are authorized by the manufacturer Using unauthorized accessories may affect your modem s performance damage your modem and violate related national regulations Avoid using the modem in areas that emit electromagnetic waves or in enclosed metallic structures eg elevators The modem is not waterproof Please keep it dry and store it in a cool dry place Don t use the modem immediately after a sudden temperature change eg from an air conditioned environment to high temperature and humidity outside In such cases there could be condensing moisture inside the modem which can cause internal damage Unplug the modem and leave it for 30 minutes before use Always handle the modem with care Be careful not to drop or bend the mod
9. o install 7 Click Continue Installation and make sure that installing requires restarting the computer 8 Left click Restart to restart the computer and finish software installation Notes If you have problems with the installation after the operations above please contact your service provider for help After the installation select Finder gt Applications and there will be a Rogers Connection Manager program listed The Wireless Data Card is ready to work normally 2 3 Using your Modem Insert your modem into an available USB port on your computer Your computer will launch the Connection Manager application automatically The modem will initialize and the main user interface will appear If the application does not launch double click Finder gt Applications gt Rogers Connection Manager to run the software 2 4 LED Indicator LED Indicator USB Modem Working Status Yellow Power on Not registered on the 2G or 3G network Green Solid Registered on the 2G network Green blinking Active data transfer on the 2G network Blue solid Registered on the 3G network Blue blinking Active data transfer on the 3G network Red solid Roaming status or no SIM card Red blinking Active data transfer in roaming status 2 5 Removing the Modem Safely Please close the application software first and then pull out the modem or USB cable 2 6 Uninstalling the Software If you need to uninstall the software cl
10. ose the application first and then select Finder gt Applications gt Rogers Connection Manager Select Move to Trash in the right click menu of Rogers Connection Manager on the computer You need to restart your computer if you wish to re install the software 3 Functions amp Operation 3 1 Main Interface The Mac PC interface comprises three parts Function Buttons System Information Bar and User Information area Function Buttons Use the Function buttons to carry out the corresponding operations Connects to the internet Messages Interface View your Contacts Opens the Rogers Home Page Change system settings View the Help file System Information Bar Use the System Information Bar to monitor your network and modem status Shows network signal strength Modem Connected New SMS message in your Inbox Modem disconnected SIM card is roaming SIM card inserted Current network type EDGE GPRS HSPA or HSPA SIM card not inserted Name of your service provider User Area This section shows user information such as the time connected and data usage 3 3 Connecting to the Internet Once you are connected you can browse web pages and access the Internet through the modem You can also receive Text Messages while surfing the Internet Connect to the Internet Click the Internet button and then click Connect to establish a connection to the internet The card requires a few seconds to verify your conne
11. roup to edit the name If a contact is selected you can carry out the following additional steps using the buttons at the bottom of the screen Delete selected records Edit the information of the selected record CopyTo Copy the records between groups or from the computer to the SIM card Send a text message to the mobile phone numbers in the selected records 3 5 1 Searching Records In the search bar you can key in any part of the record characters or a phone number and the corresponding records will be displayed Scroll to the record you want to view in detail Click to edit the information 3 6 Home Page The Home Page icon launches your default internet browser and directs you to the Rogers Home Page 3 7 Settings Click the Settings icon to switch to the settings interface Note Normally there is no need to change any of these settings as they are pre configured for your network If you change networks or are roaming you may need to modify some settings Consult your service provider for more information 3 7 1 Security Settings Enable the PIN Code You can enable a PIN code using the PIN enable feature When enabled you need to enter your PIN to start the modem The PIN code is stored on the SIM card Consult your service provider for more information or if you forget your PIN Click Revise PIN to modify the number 3 7 2 Network Settings Automatic The modem selects the network automatical
12. to give additional protection for the public and to account for any variations in measurements 1 4 System Requirements The USB Modem supports any PC or MAC system using the USB 2 0 interface and operating systems listed below Operating System Windows 2000 XP Vista 7 and MAC OS X 10 4 and above Recommended Configuration CPU PowerPC or Intel 500MHz or above Hard Disk 20MB or above available RAM 128M or above The performance of the modem may be reduced if the configuration is below the recommended requirement 1 5 Technical Specifications Networks HSPA HSUPA HSDPA UMTS GSM GPRS EDGE HSPA HSUPA HSDPA UMTS 850 1900 2100 MHz Frequency Bands GSM GPRS EDGE 850 900 1800 1900 MHz Dimensions 77mm x 28mm x 12mm Weight Approx 30g HSPA Mode up to 21Mbps HSUPA Mode up to 5 76Mbps HSDPA Mode up to 7 2Mbps UMTS Mode up to 384 Kbps EDGE Mode up to 236 8Kbps Data Rate GPRS Mode up to 57 6Kbps Working Voltage 5V Current Consumption Resting 100mA rms Max 450mA rms Maximum Emitted Power 3G Mode 250mW 2G Mode 2W Interface Type USB Standard 2 0 Supported Systems Compatible with PC and MacOS as listed Functions SMS service data service internet applied management supports MicroSD MicroSD Capacity Up to 8GB Operating Range 10 C to 55 C 2 Installation 2 1 Unpacking Check the following articles are in the package Modem USB Extension cable Quick Start Guide
13. y the FCC for each model The highest SAR values as reported to the FCC for this model phone when worn on the body are 0 959W kg for Cellular 850MHz and 1 02W kg for PCS 1900MHz Body worn measurements differ among phone models depending upon available accessories and FCC requirements While there may be differences between the SAR levels of various phones and at various positions they all meet the government requirement For body worn operation this model has been tested and meets the FCC RF exposure guidelines when used with the ZTE accessories supplied or designated for this product Use of other accessories may not ensure compliance with FCC RF exposure guidelines While there may be differences between the SAR levels of various phones and at various positions In all cases products are designed to be within the guidelines FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines Additional information on Specific Absorption Rates SAR can be found on the Cellular Telecommunications amp Internet Association CTIA web site http www phonefacts net or the Canadian Wireless Telecommunications Association CWTA web site http www cwta ca In the United States and Canada the SAR limit for mobile phones used by the public is 1 6watts kg w kg average over one gram of tissue The standard incorporates a substantial margin of safety
Download Pdf Manuals
Related Search