Bullet Camera
Contents
1. 5 Do the same procedures on the Ethernet cable on the network side Network Side Camera Side 6 Connect the Ethernet connector of the camera and the network to each side of the 2 sided female type connector 2 Sided Female Type Connector Ethernet cable from the network Ethernet cable of the camera a ACTI Connecting Vision m Hardware Manual 7 On the Ethernet cable on the camera side attach the rubber seal to the main body e 8 Attach the main body to the 2 sided female type connector n 9 Attach the clamping nut to the main body T ACTI Connecting Vision m Hardware Manual 10 Do the same procedures on the network cable side Below is a complete cable connection NOTES on using Ethernet cables For waterproof without conduit installation it is recommended to use exterior grade Ethernet cables CAT5 CAT5e CAT6 ordinary Ethernet cables are only designed for indoor use and may deteriorate quickly when exposed to outdoor elements Exterior grade Ethernet cables are waterproof and do not require a conduit 9 ACTI Connecting Vision vA Hardware Manual Waterproof with Conduit 1 Prepare the Waterproof with Conduit cable accessories included in the waterproof cable kit and flexible conduit cable not included with 72 diameter os 2 Sided Female Washer Type C2. Obtain DNS server address automatically I I I S I Use the following DNS server addresses Preferred DNS server Alternate DNS server Validate settings upon exit a OK Cancel ACTI Connecting Vision m Hardware Manual Manually adjust the IP addresses of multiple cameras If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them all of the cameras would then have the initial IP address of 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each other The easiest way to assign cameras the IP addresses is by using IP Utility IP_Utility IP Address NetMask 172 16 26 192 255 255 255 0 z Basic Search v Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Toms Acou mu 3 lass v IP Address MAC Address FW Version Model Serial No Multicast IP Status Al 172 16 26 2 00 0F 7C 07 DE 65 A1D 311 V5 07 05 AC Hemispheric Camera KCM3911 228 5 6 1 v 172 16 26 4 00 0F 7C 08 17 C2 A1D 310 V4 12 02 AC Mega IP Camera TCH1111 228 5 6 1 v 172 16 26 6 WT 6j change Networ
3. System Information Video WAC UOTE El Dot UF ICOC BE 85 Event T System User Account Factory Default Firmware Upload Save amp Reboot Logout For further operations please refer to the Firmware User Manual 30 ACTI Connecting Vision ra Hardware Manual Other Adjustments and Accessories Adjust the Viewing Angle 1 Open the front cover 2 Based on the live view from the camera adjust the focal length and focus of the target area 3 When done close the front cover CAUTION The front cover must be tightly closed to ensure water or dust does not go through any opening ACTI Connecting Vision vA Hardware Manual Attach the Sunshield The use of sunshield is optional if the camera will be installed indoors However if the camera will be installed outdoors attach the sunshield to protect the lens from all types of weather and lighting conditions 1 Loosely secure the supplied screws and washers to attach the sunshield 2 Slide to adjust the sunshield to cover the lens as far as possible but out of the camera s live view 3 Tighten the screws to fix the position of the sunshield See final installation below 32
4. Bullet Camera Hardware Manual E44 E45 E46 Ver 2013 12 04 ACTI Connecting Vision WA lt gt ACT Connecting Vision vA Hardware Manual Table of Contents Precautions 3 Sale I SIMUCUOINS sec tecccenscesasesasecac nazesusedccesncensceaneesesecusesecesecenscesveess 5 Introduction 6 List Of MOCEIS ccceeeceneceneeeseenseenseenseensenseenseonseenseenesessonseonssoness 6 Package CONC sisisi da dida dede vada Vad ca Vida RN CN CERIS 7 Physical Description eese eee serere 8 Installation Procedures 9 Mount the Camera sosta Exe E ese EU EVE ERU Smee nite META VI sae sees ae nnne 9 Waterproof Cable Installation 11 Waterproof without CONUIt ccccceececceeeeeseeeeaeeeeseeeeesaeeesaees 12 Waterproof with COndult cccccceccccsececseeeeseeeeesseeeesseeeesaeeeeaaes 16 Basic Connections 1 e ecee eire cire rene eene enhn anna nana anas 22 Connecting a Single Camera 2 0 ceecccssececceeeeeseeesseeeeeseeeesaeeeeeas 22 Connecting Multiple Cameras eeeeeeseeeeereeeeere 23 Accessing the Camera 24 Configure the IP Addresses eere 24 Using DHCP Server to Assign IP Addresses 24 Using the Default Camera IP Address
5. This equipment has been tested and found to comply with the limits for a C class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Heorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to the equipment that are not expressly approved by the responsible party for compliance could void the user s authority to operate the equipment European Community Compliance Statement C 4 This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022 and EN 5
6. 26 Access Ihe Cante Panos vavitd cence snes eevee estes 28 Other Adjustments and Accessories 31 Adjust the Viewing Angle eee esee 31 Attach the Sunshield iesssesoensessskexvaseasaxesumuac saa vERE Cuxax a Fan EHE RE CEuE VEExE 32 2 www acti com ACTI Connecting Vision vA Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product Heed all warnings You must adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instruction given may directly endanger people cause damage to the system or to other equipment Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Trademarks All names used in this manual are probably registered trademarks of respective companies Liability Every reasonable care has been taken during the writing of this manual Please inform your local office if you find any inaccuracies or omissions We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice 3 www acti com ACTI Connecting Vision m Hardware Manual Federal Communications Commission Statement
7. covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine if the video product is in proper operating condition 5 www acti com ACTI Connecting Vision vA Hardware Manual Introduction List of Models This hardware manual contains the following models 2MP Bullet with D N IR Basic WDR SLLS Vari focal lens 1MP Bullet with D N IR Superior WDR Vari focal lens SMP Bullet with D N IR Superior WDR Vari focal lens 6 www acti com ACTI Connecting Vision bis Hardware Manual Package Contents Bullet Camera Sunshield Mounting Screw Kit Sunshield Screw Kit Drill Template Quick Installation Guide Warranty Card ul Quick Installation Guide acti Pada Contenct Genes or Uomo temer Aae impr pry y me Poo onc Sper Dee Ls Preset OD yea ED Weert Ves c Safe Ld rai rd aie but Ld AUN wmm num tenant tra si e PC Pw taste mo loc Pus eee But tone at we TDI Sui emo a Q poet OME SUT ted agar fender recen nor Oat cct pase ae Pane Ramee unt im ime Lam Lim nh gd nom Re LEV e nt 2 28100 Uaername Adee Paswwond 113436 N ammang Yous
8. even a better way to discover the cameras in the network by using IP Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time The IP Utility can be downloaded for free from http www acti com IP Utility With just one click you can launch the IP Utility and there will be an instant report as follows Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Account Password 123456 IP Address MAC Address FW Version Model Serial No Multicast IP Status e 2 un LB 172 16 26 8 00 0F 7C 0A 85 46 A1D 500 V6 03 17 AC Megapixel IP Dome D61 A XX 13C 00006 228 5 6 1 a 172 16 26 108 00 0F 7C 09 A1 AC A1D 500 V6 03 D4 AC Megapixel IP Cube Camer E11 A XX 12L 00097 228 5 6 1 172 16 26 14 00 0F 7C 09 A1 B1 A1D 500 V6 03 17 AC Megapixel IP Cube Camer E11 A XX 12L 00102 228 5 6 1 172 16 26 15 00 0F 7C 09 7A 6B A1D 500 V6 03 17 AC Megapixel IP Cube Camer E13 A XX 12K 00041 228 5 6 1 192 168 0 208 00 0F 7C 09 7A 70 A1D 500 V6 04 03 AC Megapixel IP Cube Camer E13 A XX 12K 00046 228 5 6 1 172 16 26 7 00 0F 7C 0A 1E 06 A1D 500 V6 03 17 AC Megapixel IP Camera E22 A0XX 13B 00009 228 5 6 1 172 16 26 11 00 0F 7C 0A 2B 76 A1D 500 V6 03 17 AC
9. or s Rename access point Connect to a network E Connect or reconnect to a wireless wired dial up or VPN network connection See also HomeGroup Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing Windows Firewall settings ip Pa Connection Properties im btocol Version 4 TCP IPv4 Prope nies o i Som M QR RE Connect using amp Intel R 82567LM 3 Gigabit Network Connection You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically This connection uses the following items iv 3 amp Client for Microsoft Networks M f VirtualBox Bridged Networking Driver vi IE QoS Packet Scheduler 5 File and Printer Sharing for Microsoft Networks 4 Intemet Protocol Version 6 TCP IPv6 Intemet Protocol Version 4 TCP IPv4 4 Link Layer Topology Discovery Mapper O Driver amp Link Layer Topology Discovery Responder Install Uninstall Properties Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Use the following IP address IP address 192 168 0 99 Subnet mask 255 J55 255 0 Default gateway
10. stream management will be downloaded from the camera directly the user just has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case ACTI Connecting Vision al Hardware Manual The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera Assuming that the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into Web browser s address bar http 192 168 0 100 Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80 which can be omitted from the address for convenience r EE S http 921680100 O 2 gt X amp web Configurator x ni 27777 Web Configurator Account Password Language English v Logn Rest Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456 b4 ACTI Connecting Vision Hardware Manual To check the firmware version through the Web Configurator access the Setup page and click System gt System Info Web Configurator o x i Host Date amp Time Network i IP Settings Lt
11. 5024 In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures 4 www acti com ACTI Connecting Vision vA Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Water and Moisture Do not use this video product near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Don t use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the video product 3 If the video product has been directly exposed to rain or water If the video product does not operate normally by following the operating Instructions in this manual Adjust only those controls that are
12. Camera Aatocratic P Setup WEA Rouser DenCh server 1 www acti com ACTI Connecting Vision vA Hardware Manual Physical Description Side View Back View 1 Ethernet Connector Connects to the network and power source See Basic Connections on page 22 for more instructions 8 www acti com ACTI Connecting Vision ra Hardware Manual Installation Procedures Mount the Camera 1 Attach the bracket to the camera 2 Mark the location of the screw holes based on the drill template included in the package NOTE Depending on the surface where you will install the camera it may be necessary to drill three 3 holes and use the supplied screw tox 3 Attach the camera to the surface using the three 3 supplied screws 4 Adjust the camera installation angle and orientation and then tighten the two 2 screws to fix its position 9 www acti com ACTI Connecting Vision m Hardware Manual 5 Connect the RJ 45 male type connector of the camera to the 2 sided female type connector included in the waterproof cable kit On the other side of the 2 sided female type connector connect the Ethernet cable from the network 2 Sided Female Type Connector Ethernet cable from the network Ethernet cable of the camera The above cable connection can be used if the camera will be installed indoors or when a junction
13. Megapixel IP Camera E24 A XX 13B 00006 228 5 6 1 172 16 26 4 00 0F 7C 09 BB 20 A1D 500 V6 03 17 AC Megapixel IP Camera E41 A XX 12L 00112 228 5 6 1 172 16 26 242 00 0F 7C 09 B9 76 A1D 500 V6 02 03 AC Megapixel IP Camera E42 A XX 12L 00286 228 5 6 1 172 16 26 12 00 0F 7C 0A 24 1A A1D 500 V6 03 17 AC Megapixel IP Camera E44 A XX 13B 00002 228 5 6 1 172 16 26 193 00 0F 7C CA 1B 34 A1D 500 V6 03 17 AC Megapixel IP Camera E45 A 01 13A 00004 228 5 6 1 172 16 26 137 00 0F 7C 09 52 0E A1D 500 V6 02 03 AC Megapixel IP Dome E51 A XX 12J 00073 228 5 6 1 192 168 0 156 00 0F 7C 09 95 6C A1D 500 V6 02 03 AC Megapixel IP Dome E53 A XX 12K 00147 228 5 6 1 172 16 26 180 00 0F 7C 09 D5 BD A1D 500 V6 03 17 AC Megapixel IP Dome E53 A XX 13A 00089 228 5 6 1 172 16 26 176 00 0F 7C 0A 31 15 A1D 500 V6 03 07 AC Megapixel IP Dome E85 A XX 13B 00010 228 5 6 1 mm 5 bh _ uma DIBIBIBIBIBIBIBIBBDB9IDIDIDI You can quickly see the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already ACTI Connecting Vision m Hardware Manual Using the Default Camera IP Address If there is no DHCP server in the given network the user may have to assign the IP addresses to both PC and camera manually to make sure t
14. box will be used on an outdoor installation If the camera will be installed outdoors and without a junction box to protect the cable connection from rain or dust use exterior grade Ethernet cables CAT5 CAT5e CAT6 and be sure to apply the waterproof installation see Waterproof Cable Installation on page 11 0 ACTI Connecting Vision vA Hardware Manual Waterproof Cable Installation There are two ways to waterproof the cable installation e Waterproof without Conduit Waterproof cable connection with naked cable e Waterproof with Conduit Waterproof cable connection with watertight flex conduit The Waterproof Cable Kit that came with the camera contains the following items Waterproof without Conduit Accessories 2 Sided Female Type Connector Waterproof with Conduit Accessories The 2 Sided Female Type Connector is used in all types of cable connection n ACTI Connecting Vision vA Hardware Manual Waterproof without Conduit 1 Prepare the Waterproof without Conduit cable accessories Detach the parts as follows u Main Body Rubber Seal Clamping Nut NOTE The above accessories come in two sets one for the Ethernet cable of the camera and the other for the network 2 Insert the clamping nut through the Ethernet cable of the camera 3 Insert the rubber seal 2 b Act Hardware Manual 4 Insert the main body
15. ct the parts of the network side cable to the 2 sided female type connector 2 Sided Female Type Connector Ethernet cable Ethernet cable from the network of the camera 13 On the Ethernet cable on the camera side attach the rubber seal to the main body r 14 Attach the main body to the 2 sided female type connector n 20 ACTI Connecting Vision vA Hardware Manual 15 Attach the clamping nut to the main body The waterproof cable connection is complete ACTI Connecting Vision al Hardware Manual Basic Connections To connect the camera you need to prepare the following e Power over Ethernet PoE supported switch to connect multiple cameras or PoE injector to connect a single camera e Ethernet cables Connecting a Single Camera To connect a single camera use a PoE injector to supply both data and power to the camera using one Ethernet cable Follow the procedures below 1 Connect the camera to the PoE injector directly or by using the 2 sided female type connector Connect the PoE injector to the network and an AC power source 3 Connect a PC to the same network Ethernet Cable gt Ethernet Cable Data Ethernet Cable Data Power AC Power Source Camera 2 b4 ACTI Hardware Manual Connecting Multiple Cameras To connect multiple cameras us
16. e a PoE switch 1 Connect the camera s to the PoE switch directly or by using the 2 sided female type connector of each camera 2 Connect the PoE switch to a network and an AC power source 3 Connect a PC to the same network Ethernet Cable LS Ethernet Cable Data P Cabl PoE Switch i AC Power Ethernet Cables Source Data Power LUE Ur Ur i ias is Lr Ur das i des Cameras P4 ACTI Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only the last number of the IP address is different from each other There are 2 different approaches to IP Address management in Local Area Networks by DHCP Server or Manually Using DHCP Server to Assign IP Addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from DHCP server automatically In such case the camera will immediately be ready for the access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in other to be able to access it by us
17. hey are in the same network segment When the camera is plugged into network and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera Manually adjust the IP address of the PC In the following example based on Windows 7 we will configure the IP address to 192 168 0 99 and set Subnet Mask to 255 255 255 0 by using the steps below Se x 5E All Control Panel Items Network and Sharing Center v 4 Search Control Pane p n Network and Internet Network Connt Control Panel Home i i A i A View your basic network information and set up connections Change adapter settings 4 n e See full map a Change advanced sharing Organize v Disable this network device Diagnos Local Area Connection M SISO NP PC1 Network Internet Network settings TH compan dt Intel R 8 Disable View your active networks Connect or disconnect Status Diagnose de Network Access type Internet Work network Connections Local Area Connection Bridge Connections Create Shortcut Change your networking settings T Set up a new connection or network Delete Set up a wireless broadband dial up ad hoc or VPN connection or set up a router
18. ing a Web browser The quickest way to discover the cameras in the network is to use the simplest network search built in the Windows system just by pressing the Network icon all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our cameras In the example below we successfully found the camera model that we had just connected to the network G Network X Metwor P Organize v Search Active Directory Network and Sharing Center Add a printer Add a wireless device a w L1 e CAIVIERA USD356 1 CAMERA 09DS8FF a Libraries D51 A 02 12H 00010 Documents D61 A XX 13C 00006 2 Music SS E11 A XX 12L 00097 a E11 A XX 12L 00102 B Videos M E13 A XX 12K 00041 a E22 A0XX 13B 00009 J Computer Select a file 2 ex ex je lex lex lex les Ies E24 A XX 13B 00006 RAE amp Local Disk C Bier oen to preview l Se E42 A XX 12L 00286 i Network E44 A XX 13B 00002 j E46 A 01 13A 00004 j E51 A XX 12 00073 j E53 A XX 13A 00089 jj E85 A XX 13B 00010 ct LINT 91 items ua 24 ACTI Connecting Vision m Hardware Manual By double clicking with the left mouse on the camera model it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already If you work with our cameras regularly then there is
19. k Address Ea KCM7311 228 5 6 1 v 172 16 26 7 d TCM6630 228 5 6 1 v 172162610 004 Dynamic IP Address TCM4201 228 5 6 1 v 172 16 26 11 0 4 KCM3911 228561 v 172162613 00 KCM5111 228 5 6 1 v 172 16 26 40 KCM5211 228 5 6 1 v 172 16 26 41 a US KCM5311 228 5 6 1 v 172 16 26 50 Netmask KCM5111 228 5 6 1 v 172 16 26 52 KCM5311 228 5 6 1 v 172 16 26 53 TCH5311 228 5 6 1 E v 172 16 26 54 TCMs611 228561 v 172 16 26 55 TCH5111 228 5 6 1 v 172 16 26 57 Video Server TCD2100 228 5 6 1 wv 172 16 26 61 Megapixel IP Camera TCM1231 228 5 6 1 With the procedure shown above all the cameras will have unique IP addresses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 168 0 120 Later by pressing the Refresh button of the IP Utility you will be able to see the list of cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time 2 P4 ACTI Connecting Vision Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same net
20. onnector Converter Main Body 2 Detach the parts of the main body as follows Clamping Nut Body Sealing Insert Lock Nut r NOTE The Lock Nut is designed for use with junction boxes and will not be used in this installation Please set it aside r ACTI Connecting Vision d Hardware Manual 3 Insert the clamping nut through the Ethernet cable of the camera 4 Insert the rubber seal 5 Insert the main body and then set the camera side cable aside 7 ACTI Connecting Vision vA Hardware Manual 6 On the network side insert the Ethernet cable through the flex conduit 7 Insert the clamping nut through the flex conduit 8 Insert the sealing insert and attach it at the end of the flex conduit r 4 ACTi Connecting Vision Hardware Manual 9 Insert the body through the Ethernet cable and then the converter 10 Insert the washer into the thicker side of the 2 sided female type connector j 11 Connect the Ethernet cable of the network side to the thicker end of the 2 sided female type connector and the camera side to the shorter end Thicker end for network 2 Sided Female s Type Connector Ethernet cable from the network Ethernet cable Shorter end for of the camera camera 9 ACTI Connecting Vision ra Hardware Manual 12 Conne
21. work segment it is possible to use the Web browser of the PC to access the camera You can use any of the browsers to access the camera however the full functionality is provided only for Microsoft Internet Explorer The browser functionality comparison Functionality Internet Explorer Other browsers Live Video PTZ Contro Capture the snapshot Video overlay based configuration Motion Detection regions Privacy Mask regions All the other configurations When using non Internet Explorer browsers free third party software plug ins must be installed to the PC first to be able to get the live video feed from the camera Check the firmware version of the camera to determine which plug in is necessary Required Plug in A1D 500 V6 04 xx AC or older Basic VLC Media Player http www videolan org A1D 500 V6 05 xx AC or newer QuickTime http www apple com quicktime download The camera firmware version can be found on the FW Version column of the IP utility or access the Setup page of the Web Configurator see page 30 Disclaimer Notice The camera manufacturer does not guarantee the compatibility of its cameras with VLC player or QuickTime since these are third party softwares The third parties have the right to modify their utility any time which might affect the compatibility In such cases please use Internet Explorer browser instead When using Internet Explorer browser the ActiveX control for video
Download Pdf Manuals
Related Search