4208 Installation Instructions
Contents
1. ADEMCO N2816V5 10 94 No 4208 8 POINT REMOTE POINT MODULE INSTALLATION INSTRUCTIONS GENERAL The ADEMCO No 4208 REMOTE POINT MODULE RPM is an optional device used with point protection security systems such as some VISTA controls Each RPM interfaces with and uniquely identifies up to eight protection loops to the control Although the No 4208 will not in any way expand the number of available protection points in a system it does afford a more simple installation for companies who homerun their sensors to the control or who desire to group the sensors from an area of the proteced premises onto one remote point module All eight of the sensor loops are end of line resistor supervised permitting the use of N O or N C sensors on each loop All eight loops have normal 400 msec response to sensor faults However two can be selected as a group to have fast 10 msec response Six of the loops can be used with either mechanical or reed contacts and the remaining two can be used just with reed contacts SIDE VIEW THIS SWITCH SETTING DIP Switch Position INSTALLATION The No 4208 installation procedures include programming mounting and wiring PROGRAMMING Programming the No 4208 involves assigning a starting sensor address by setting four positions of a five position DIP switch Each setting presets a series of eight sensor loop control addresses 1 8 9 16 17 24 etc Use only switch positions 2 3 4 5 t2. IED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BE THE SELLER S OWN NEGLIGENCE OR FAULT Seller does not represent that the products it sells may not be compromised or circumvented that the products will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the products will in all cases provide adequate warning or protection Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or a guarantee that such wili not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any previous warranties and is the only warranty made by Seller on this product No increase or alteration written or verbal of the obligations of this Limited Warranty is authorized ADEMCO ALARM DEVICE MANUFACTURING CO A DIVISION OF PITTWAY C
3. ORP 165 EILEEN WAY SYOSSET NY 11791 COPYRIGHT 1994 PITTWAY CORPORATION N2816V5 10 94
4. anel instructions to determine the valid zone numbers for that control panel Diagram 1 DIP Switch Settings MOUNTING AND WIRING 2 WIRE the No 4208 by connecting the polling loop and WARNING All power should be disconnected before the protection loops see Diagram 2 Maximum proceeding length of protection loop is 1200 feet using 22 gauge 1 MOUNT the No 4208 in a climate controlled location twisted pair wire See the instructions which a Remove the front cover accompany the control concerning polling loop b Draw the mounting holes using the back cover as restrictions a template Drill the screw holes and install the gt 3 ATTACH the wired No 4208 to its mounting location included mounting screws and tighten the mounting screws 4 RECORD ali system information on the cover s label 5 REPLACE the cover For UL Listed Commercial Burglary Usage The No 4208 must be mounted in a tamper protected enclosure such as the control panel cabinet TERMINALS EOL RESISTOR CURRENT DRAW LOOP RESPONSE TYPE OF CONTACTS 14 2 4 700 ohms 1 4W 1 Miliamp Reed or Mechanical 4 700 ohms 1 4W 1 Milliamp Reed or Mechanical 34 49 1 Milliamp Reed or Mechanical Reed or Mechanical Reed or Mechanical Reed or Mechanical Reed only For UL Liste Commercial Fire Usage Loops 7 and 8 may not be used Use N O contacts on loops 1 6 Style B supervise these loops using mode
5. cifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures If using an indoor antenna have a quality outdoor antenna installed Reorient the receiving antenna until interference is reduced or eliminated Move the antenna leads away from any wire runs to the control communicator Plug the control communicator into a different outlet so that it and the receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printing Office Washington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment ADEMCO LIMITED WARRANTY Alarm Device Manufacturing Co
6. l EOL47 Fire listed 4 7k EOLR purchased separately packaged 16 per bag For UL Listed Commercial Burglary Usage Use N O or N C contacts on loops 1 8 Supervise using EOLR _ 4 700 Ohms S JA 4 700 Ohms j 4 700 Ohms o _ 2 4 700 Ohms i JA 4 700 Ohms supplied 4 700 Ohms s 30 000 Ohms x 30 000 Ohms s DIAGRAM 2 No 4208 SUMMARY OF CONNECTIONS SPECIFICATIONS ENVIRONMENTAL Sensor Loop Response Temperature 4 20 C to 158 F 70 C Slow 400 msec ali loops Humidity 90 RH non condensing Fast 10 msec POWER CONSUMED option for Loops 1 and 2 Voltage Input 8 11V Sensor Loop Current Provided Current Drain 16 mA Loops 1 6 1 milliamp DIMENSIONAL P oky p p nly s i o a a PON Sensor Loop Wiring Maximum of 1200 feet Bea of Depth 1 3 8 35mm No 22 AWG 0 65 mm O D wire FEDERAL COMMUNICATIONS COMMISSION FCC STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception ft has been type tested and found to comply with the limits for a Class B computing device in accordance with the spe
7. mpany a Division of Pittway Corporation and its divisions subsidiaries and affiliates Seller 165 Eileen Way Syosset New York 11791 warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 18 months from the date stamp control on the product or for products not having an Ademco date stamp for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period in which case the shorter period shall apply Seller s obligation shall be limited to repairing or replacing at its option free of charge for materials or tabor any product which is proved not in compliance with Seller s specifications or proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service For warranyt service return product transportation prepaid to Ademco Factory Service 165 Eileen Way Syosset New York 11791 THERE ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPL
8. o assign these numbers DIP switch position 1 selects fast OFF or slow ON response for sensor loops 1 and 2 Important Each No 4208 used utilizes eight sequential sensor ID numbers whether or not all eight are used Do not assign unused ID numbers to other modules Refer to the control panel Installation Instructions for the programming information for each point and to determine the valid range of points for the system NOTE Switches 2 5 are shown in ON position PRESETS THE LOOPS TO THESE SENSOR ADDRESSES Loop Number 1 2 3 4 5 a 2 3 4 5 6 7 8 on on on on 1 2 3 4 5 6 7 8 on on on OFF 9 10 11 12 13 14 15 16 on on OFF on 17 18 19 20 21 2 23 24 LOOPS 1 and 2 on on OFF OFF 25 26 27 28 29 30 31 320 S RESPONSE TIME e CA on SLOW on OFF on on 33 34 35 36 37 38 39 40 n SEE EARN on OFF on OFF 41 42 43 44 45 46 47 4 SHOWN OFF on OFF OFF on 49 50 51 52 53 54 55 sr on OFF O OFF OFF 57 58 59 60 61 62 63 64 N OFF on on on 65 66 67 68 69 70 71 72 ns OFF on on OFF 73 74 75 76 77 78 79 80 OFF on OFF o 81 82 83 84 85 86 87 7 OFF on OFF OFF 89 90 91 92 98 94 95 96 OFF OFF on on 97 98 99 100 101 102 103 104 OFF OFF on OFF 105 106 107 108 109 110 111 112 OFF OFF OFF on 1183 114 115 116 117 118 119 129 OFF OFF OFF OFF 121 122 123 124 125 126 127 N A Do not select 1 8 for VISTA If 9 16 is selected for VISTA Loop 1 Zone 9 will be inactive NOTE Consult the Control P
Download Pdf Manuals
Related Search