User MANUAL - Argos Support
Contents
1. Leaks from battery cells can occur under extreme usage or temperature conditions If the liquid gets on skin wash quickly with water If the liquid gets into the eyes flush them immediately with clean water for a minimum of 10 minutes Seek medical attention It is normal for the charger to become warm to the touch when charging Use only attachments consumables or spares recommended or supplied by Hoover Do not pick up hard or sharp objects matches hot ashes cigarette ends or other similar items Do not spray with or pick up flammable liquids cleaning fluids aerosols or their vapours Do not continue to use your appliance or charger if it appears faulty Hoover service To ensure the continued safe and efficient operation of this appliance we recommend that any servicing or repairs are only carried out by an authorised Hoover service engineer Do not use the appliance to clean animals or people Do not replace the Robot batteries with non rechargeable batteries End of life battery removal If the appliance is to be disposed of the batteries must first be removed The appliance must be disconnected from the supply mains when removing the battery Dispose of the batteries safely Run the appliance until it stops because the batteries are fully discharged Used batteries should be taken to a recycling station and not disposed of with household waste To remove the batteries please contact the Hoover Customer Centre or proceed accor2. See Cleaning the Edge Cleaning Brush Er02 Debris trapped in the agitators See cleaning the agitators Er04 Left drive wheel motor is overloaded See cleaning the drive wheels 05 Right Drive Wheel motor overloaded See Cleaning the Drive Wheels 07 right drive wheel making contact with the ground cleaning the drive wheels Er09 Dust container is absent Replace dust container Er12 Debris in the left edge brush See Cleaning the edge brushes ATTENTION If any of these failures persist contact your local Hoover representative DO NOT try to disassemble the Robo com by yourself IMPORTANT INFORMATION Hoover Spares and Consumables Always replace parts with genuine Hoover spares These are available from your local Hoover dealer or direct from Hoover When ordering parts always quote your model number Consumables e Robo com Lithium lon Battery Pack RB219 35601403 e Floor Brushes RB220 35601404 e Edge Cleaning Bristles RB221 35601405 e Floor Cleaning Pads x5 RB222 35601406 Pre Motor Filter RB223 35601407 Remote Control RB214 35601340 Dust Container RB224 35601408 Virtual Barrier RB203 35601256 Quality Hoover s factories have been independently assessed for quality Our products are made using quality system which meets the requirements of ISO 9001 The Environment The symbol on this appliance indicates that this appliance may not be treated as
3. household waste Instead it must be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this appliance please contact your local city office your household Cma and waste disposal service or the shop where you purchased the appliance This appliance complies with the European Directives 2006 95 EC 2004 108 EC and 2011 65 EU HOOVER Limited Pentrebach Merthyr Tydfil Mid Glamorgan CF48 4TU UK Your Guarantee The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased The bill of sale or receipt must be produced when making any claim under the terms of this guarantee Subject to change without notice Certain Models Only May vary according to model GENERATION FUTURE PRINTED IN P R C 48010192
4. household waste REPLACING THE REMOTE CONTROL BATTERIES Fig 27 The remote control is fitted with 2 x AAA batteries 1 Remove the battery cover 2 Remove the old batteries and replace with the new batteries ensuring the polarity is correct Replace the cover 3 Dispose of the batteries safely Used batteries should be taken to a recycling station and not disposed of with household waste REPLACING THE VIRTUAL BARRIER BATTERIES Fig 28 The virtual barrier is fitted with 2 x D batteries 1 Turn the virtual barrier over and rotate the retaining clip Remove the battery cover 2 Remove the old batteries and replace with the new batteries ensuring the polarity is correct Replace the cover 3 Dispose of the batteries safely Used batteries should be taken to a recycling station and not disposed of with household waste TROUBLESHOOTING The following is a list of commonly encountered problems and solutions If any of these problems persist contact your local Hoover representative The Robo com does not Check that the Robo com is switched on work Check that the dust container filter and motor are clean Check if the Robo com needs to be charged Cleaning power is weak Turn power off and e Empty dust container Check and clean the filter and motor Check and clean the Floor Brushes Check and clean the sensors Check and clean the drive wheels The Remote Control does Check the batteries not work Check the battery of
5. COM CLEANER Before performing any maintenance task ensure the Robo coms is switched off 1 Turn the Robo com off and remove it from the charging station 2 Use a damp cloth with a little soap to clean all surfaces DO NOT allow water into any part of the product whilst cleaning 3 Dry with a soft cloth EMPTYING THE DUST CONTAINER Empty the dust container every cleaning cycle or when it is full 1 Turn the Robo com off and remove from the charging station 2 Press the dust container release button and remove the dust container from the Robo com8 3 Hold the dust container over a bin to empty 4 Use the multi purpose cleaning brush when necessary to remove any excess dust from the internal surface of the dust container 5 Refit the dust container to the CLEANING THE FILTERS Fig 17 The Robo coms is fitted with a pre motor filter To maintain optimum cleaning performance regularly clean the pre motor filter The pre motor filter should be cleaned every 5 dust container empties and should be washed IMPORTANT The pre motor filter should be cleaned and washed after the dust container has been emptied 5 times Failure to clean your filter may result in air blockage overheating and product failure This may invalidate your guarantee 1 Turn the Robo com off and remove from the charging station 2 Press the dust container release button and remove the dust container from the Robo com8 3 Pull the fil
6. HOOVER ROBOECOM USER MANUAL GENERATION FUTURE INSTRUCTIONS FOR SAFE USE This appliance should only be used for domestic cleaning as described in this user guide Please ensure that this guide is fully understood before operating the appliance Always switch off and remove the charger from the socket before cleaning the appliance or any maintenance task This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision If the power cord is damaged stop using the appliance immediately To avoid a safety hazard authorised Hoover service engineer must replace the power cord If the area to be cleaned contains a balcony a physical barrier should be used to prevent access to the balcony and ensure safe operation Small children and pets must be supervised while Robo com is cleaning Battery Charging Use only the original charger supplied with the appliance Check that your supply voltage is the same as that stated on the charger Never charge the batteries in temperatures above 30 C or below 0 C Plug the charger delivered with this appliance into a suitable socket
7. L mark REPLACING THE EDGE BRUSHES If the edge brush is damaged it will need to be replaced Replacement edge brush can be obtained from your Hoover retailer 1 Switch the off and turn it over 2 Remove the retaining screw with a screwdriver 3 Remove the old edge brush and push the new one in place 4 Replace and tighten the screw WARNING Please assemble it on the correct side referring to R and L mark CLEANING THE FRONT WHEEL Fig 22 1 Switch the Robo com off and turn it over 2 Remove any dirt or hair trapped in the wheel 3 Clean the wheel with a dry cloth 4 Check that the wheel can rotate freely CLEANING THE FLOOR SENSORS Fig 23 The floor detection sensors are located in the base of the Robo com Clean the sensors each time the dust container is emptied Frequent cleaning is recommended to ensure optimum cleaning performance and safe operation of your Robo com 1 Turn Robo com off and remove from the charging station 2 Turn the Robo com over 3 Use a dry soft cloth or cotton swab to wipe the sensors CLEANING THE SENSOR WINDOWS Fig 24 The wall detection sensors are located in bumper of Robo com Clean the sensor windows each time the dust container is emptied frequent cleaning is recommended to ensure optimum performance of your Robo com3 Use a dry soft cloth or cotton swab to wipe the sensor windows CLEANING THE FLOOR POLISHER PAD Fig 25 1
8. Turn Robo coms off 2 Press the dust container release button and remove the dust container from the Robo coma 3 Pull out the clip of floor polisher pad holder from the dust container 4 Remove the floor polisher pad from the floor polisher pad holder and wash using hand warm Certain Models Only May vary according to model Fig 26 Fig 27 12 water Remove excess water and leave to dry before re using 5 Re assemble when fully dry REPLACING THE BATTERIES WARNING Only use approved replacement parts for your Robo com Using parts not validated by Hoover are dangerous and will invalidate your guarantee WARNING If the Robo com virtual barrier and remote control is not to be used for several months please remove the Batteries and store in a dry location WARNING Always make sure your device is switched off before changing your batteries REPLACING THE ROBO COM BATTERIES Fig 26 The Robo com is fitted with a rechargeable Lithium ion battery pack Replace with Battery Pack Ref RB219 1 Turn the Robo com over and place on a level surface Remove the screws from the battery cover and then remove it 2 Remove the old battery pack and replace with the new battery pack ensuring the polarity is correct Replace the cover 3 Recharge the Robo com referring to main product recharge 4 Dispose of the batteries safely Used batteries should be taken to a recycling station and not disposed of with
9. apacity lithium ion batteries These rechargeable batteries are guaranteed for a period of 6 months if they are maintained and operated according to this User Manual In the event of a significant drop of the Robo com performance replacement batteries can be obtained from your Hoover retailer Only use Hoover approved replacement parts for your Robo com Use of parts that not approved by Hoover are dangerous and will invalidate your warranty Only use the supplied charging station and main power adaptor to recharge your Robo com Use of the incorrect charging station or main power adaptor is dangerous and will invalidate your warranty CONTENTS OF THE BOX Robo com Charging station Filter Mains Power adaptor User Manual Remote Control Virtual Barrier Floor Polisher Pad Holder Floor Polisher Pad Multi purpose Cleaning Brush Edge Cleaning Brush X2PCS Certain Models Only May vary according to model GETTING TO KNOW YOUR CLEANER Robo com Top View 1 2 3 4 5 Robo com Bottom View 1 SNES N Certain Models Only Te Furniture Protector fa Let Sensor Window 7 25 24 Charging Plug Dust Container Exhaust Grille May vary according to model GETTING TO KNOW YOUR CLEANER Charging Station Virtual Barrier Virtual Barrier Selector Switch L
10. cated in the dust container of Clean the sensor window each time the dust container is emptied Frequent cleaning is recommended to ensure optimum performance of your Robo coms Use a dry soft cloth or cotton swab to wipe the sensor window CLEANING THE DRIVE WHEELS Fig 20 1 Switch the Robo com off and turn it over 2 Remove any dirt or hair trapped in the wheels 3 Clean the wheels with a dry cloth 4 Check that the wheels can rotate freely CLEANING THE EDGE BRUSHES Fig 21 The edge brushes can be easily worn from heavy use so you should check it regularly to monitor their conditions 1 Switch the Robo com off and turn it over 2 Remove the retaining screw with a screwdriver 3 Use a pair of scissors to remove any trapped hair or debris CORRECTING EDGE BRUSHES DEFORMATION The edge brushes can sometimes be deformed during transportation or when the product is used under particular conditions If this happens it is possible to return to the original shape by putting the bristles in hot water GOOD 1 Switch the Robo com off and turn it over 2 Remove the retaining screw with a screwdriver Remove the edge brushes 3 Gently lower the bristles in hot water 4 Hold each set of bristles until they have recovered and straightened Then remove and leave to dry 5 Once completely dry reassemble and screw in place WARNING Please assemble it on the correct side referring to R and
11. control function can be activated by pressing the B or F button on the main product for 4 seconds This function will be also reset when the main product is switched off When the lamp under m Z the B or F button or the icon on the LCD depending on the model will be illuminated this indicates the remote control function is available Remote control function ON 1 nn VIRTUAL BARRIER SET UP 19 71 To install batteries see cleaner maintenance Replacing the batteries The virtual barrier is used to prevent the Robo com entering certain rooms or areas Before setting the virtual barrier remember to e Remove any obstacles from the direct path of the virtual barrier The virtual barrier should be placed on the same surface that Robo com is operating on Ensure the virtual barrier is more than 3m away from the charging station NOTE We recommend to use a physical obstacle to prevent Robo com entering any danger area 1 Position the virtual barrier so that the infrared transmitter is pointing across the area you want to create the barrier 2 Slide the selector switch to the desired length of the barrier Range Type o 3 Check the virtual barrier provides adequate cover whilst the Robo com is operational NOTE The battery power usage relates directly to the infra red level For longer battery life to choose the correct range icon NOTE The near infrared transmitter will stop t
12. ding to the following instructions NOTE Should you experience any difficulty in dismantling the unit or for more detailed information on treatment recovery and recycling of this appliance please contact your local city office or your household waste disposal service IMPORTANT NOTES BEFORE USE Please read the following information carefully before using your Robo com or its accessories Do not disassemble the Robo com and do not attempt to repair it yourself If a fault occurs please contact the Hoover after Sales Service for professional advice Stairs The Robo com uses sensors to avoid falling down steps stairs or over an edge In some situations the sensors can become confused The Robo com cannot detect steps that are less than 8cm in height Steps less than 8cm may cause the Robo com to fall down If available use the Virtual Barrier to protect your Robo com from falling Highly reflective or very dark surfaces used on some steps stairs such as glass or polished ceramics may cause the Robo coms to fall down If available use the Virtual Barrier or place a carpet on the lower step to protect your Robo com from falling Using your Robo com on mezzanines landings or raised areas without borders should be avoided If available use the Virtual Barrier to prevent Certain Models Only May vary according to model your Robo com entering these areas Battery Use Your Robo com is powered by rechargeable high c
13. e the Battery The main power adaptor must only be connected to a standard mains power socket BATTERY For optimum Battery performance it is recommended that you keep your Robo com Batteries fully charged When the Robo com is not in use it should be left connected to the charging station or the mains power adaptor The Robo com has an intelligent charging system that ensures the batteries stay fully charged whilst preventing them from becoming overcharged To avoid accidents make sure that every person in the room is aware of the presence of Robo com If the Robo com becomes lost place the Robo com on the charging station manually NOTE When you don t use Robo com for a long time please disconnect it from charging station amp main power adaptor Wi Fi SETUP You can switch on or off the Wi Fi function by pressing for 1 second the sensitive Wi Fi button on main product control panel When the Wi Fi status icon is illuminated it means function is available or vice versa You can also activate this function by pressing for 4 seconds the Timing Setting Button amp Wi Fi Switch button on the remote control 1 You can download the application by scanning the left code Fig 1 2 Install it on your smartphone tablet 3 Following the instruction the application to setup your Robo com8 NOTE You can reset the WI FI setting by pressing the AUTO button on the main product for 4 seconds Once reset you can will h
14. ear a ring tone CHARGING STATION SETUP Before use remove obstacles that may get in the path of the Robo com Pay attention to Objects that can be easily knocked over e Edges of carpets or rugs that it may get caught on Floor length curtains and tablecloths Heat sources or flammable items Power cords and cables Fragile objects 1 Place the charging station on a non reflective level floor preferably against a wall If the floor surface is too reflective it will interfere with the Robo com navigation system and it may have difficulty locating the charging station 2 There should not be any objects in the area around the charging station for 3m in front and 0 5m to each side Fig 2 3 Plug in the mains power adaptor and connect to the charging station Make sure the power cord is not caught underneath the charging station 4 Make sure the power cord is not tangled or stretched If there is an excess use the power cord tie to store it neatly 5 Check that the dust container is inside on Robo com 6 Guide your Robo com into the charging station to begin During normal use it will take approximately 3 hours to complete a full recharge NOTE Initial charging will take approximately 4 hours MAIN PRODUCT RECHARGE Fig 3 4 5 Always recharge your Robo com for optimum performances Automatic Charging When the Robo com battery capacity is at 15 it will stop cleaning and search for the charging station Once docked wi
15. he Robo com coming any closer than 50cm to the virtual barrier CHANGING THE VOICE LANGUAGE Fig 8 The Robo com is able to communicate in English French Italian or Spanish The default language is English To change this With Remote Control 1 Turn the Robo com on 2 Press and hold the Voice Button for 4 seconds until you hear the current language setting 3 Press the Voice button again until you hear the next language Repeat this until you hear the desired language setting 4 Once selected the Robo com will change the settings Do not press the remote control again With Wi Fi Application Following the instruction in the Wi Fi Application NOTE The language information will appear for 5 seconds on the display ADJUSTING VOICE VOLUME Fig 9 With Remote Control 1 Press the voice button to select the desired volume You can select Low Medium High or OFF 2 The volume will appear on the display With Wi Fi Application Following the instruction in the Wi Fi NOTE The voice volume will appear on the display for 5 seconds USING YOUR ROBO COM CLEANER Power On 1 Press the ON OFF power switch on the side of the Robo com 2 The LCD screen will illuminate NOTE If your Robo coms is already switched on but in standby mode it can be activated from the remote control or pressing one of the touch sensitive buttons NOTE The touch sensitive buttons on the R
16. ing mode by Fig 11 1 Press the AUTO Sensitive touch control on Robo com 2 Press the AUTO button on the remote control 3 Following the instruction in the Wi Fi Application Robo com will automatically choose the best cleaning mode to clean your room It will use 4 different cleaning patterns NOTE You can reset the Wi Fi setting by pressing the AUTO button on the main product for 4 seconds Once reset you can will hear a ring tone ZIG ZAG EDGE ELLIPTICAL SQUARE NISO You can activate the SPOT cleaning mode by Fig 12 1 Press the Sensitive touch control on Robo com 2 Press the button on the remote control 3 Press the SPOT button on the APP menu Use this mode to intensively clean a confined area Robo com will move following a elliptical pattern where the radius will continuously increase With the remote control or Wi Fi application you can also activate all the other cleaning programs Fig 13 14 Manual Navigation The Robo com can be controlled manually at any time during a cleaning program The navigation arrow buttons in the remote control Wi Fi application will move the Robo com the desired direction with the suction activated With the remote control or Wi Fi application the Robo com can be controlled up to a long distance even behind a wall S TURBO FULL amp GO 65 Press the FULL amp GO button on the remote control or Wi Fi applicati
17. le the hour will start flashing on the display Use the up and down arrow keys to select the desired hour Press the OK confirmation button 4 The minute display will flash use the up and down arrow keys to select the desired minute Press the OK confirmation button 5 The cleaning schedule for the days has been selected You can easily see it thanks to the illuminated dash under scheduled day days With Wi Fi Application Following the instruction in the Wi Fi Application NOTE With the Wi Fi application the cleaning hour can be scheduled differently for each day 9 Certain Models Only May vary according to model 10 Fig 17 Fig 18 Home Mode Fig 15 You can command your Robo com return to the charging station for charging by 1 Press the sensitive touch control on the robot 2 Press the button on the remote control 3 Following the instruction in the Wi Fi Application ADDITIONAL FEATURES Demo Mode With remote control Press the demo button once to start the product demonstration This will start in Loop mode To stop the demonstration presses the demo button again With Wi Fi Application From the menu press demo button FLOOR POLISHER Fig 16 Attached the floor polisher pad holder to the underside of Robo com the floor polisher pad holder is used to polish marble parquet wooden and other delicate Flooring NOTE Do not use on a carpeted surface MAINTAINING YOUR ROBO
18. obo com be unreliable if your hands are wet SETTING THE DAY TIME ON THE Robo com Fig 10 With Remote Control 1 Press the time setting button a flashing line will appear below the day icon If this button is pressed for an extended time the Wi Fi function will be switched ON OFF 2 Use the up and down arrow on the remote control until the line appears below the correct day Press the OK confirmation button to confirm 3 The hour display will flash Press the up and down arrow on the remote control until the correct hour 8 Certain Models Only May vary according to model is displayed Press the confirmation button to confirm 4 The minute display will flash Press the up and down arrow on the remote control until the correct minute is displayed Press the OK confirmation button to confirm 5 Day and time are now set With Wi Fi Application Following the instruction in the Wi Fi Application NOTE The date will be automatically updated according to your smartphone once you connect to your with the APP in your smartphone CLEANING PROGRAMS Robo com use AAI Infrared Navigation an advanced navigation system that uses the algorithmic calculation to define the best path to efficiently clean your room With the dust sensor on dust detection the will automatically initiate a cleaning cycle and will follow an elliptical pattern You can activate the automatic clean
19. on to make Robot return to the base On the display the FULL amp GO indicator will be illuminated After being fully charged Robo com L Ars will automatically start cleaning for one cycle and the FULL amp GO option will be reset HOOVER Turbo Option ON OFF EH You can switch on or off the turbo mode by 1 Press the TURBO button on remote control 2 Press the TURBO button on the APP menu The turbo option is illuminated when turbo is on and Robo com will work on turbo speed Robo com will start to work at a faster speed covering quicker the area to clean Otherwise Robo com will work on normal speed Scheduled Cleaning You can decide what time the Robo com will start cleaning daily or weekly To set a cleaning schedule follow see setting Up the Cleaning Schedule SETTING UP THE CLEANING SCHEDULE Fig 14 With remote control The Robo com can be programmed to automatically clean each day or on specific days as desired Once set up this will occur at the same time on each day specified To set up a cleaning schedule over one week complete the following 1 Press the scheduling function button on the remote control A flashing box will appear around M Monday 2 Use the up and down arrow buttons to select the desired day and then press the OK confirmation button to confirm that day You can also choose multiple days up to 7days 3 Once each day of the week has been selected you can decide the hour of the cleaning schedu
20. ong Range Infrared Transmitter 37 41 40 44 Medium Range Near Infrared Transmitter Certain Models Only May vary according to model GETTING TO KNOW YOUR CLEANER Remote Control 50 5 Timing Setting Button amp Wi Fi Switch Button HOOVER Robo com Display Screen And Control Panel 120 4 Ee m m m 2 E 68 67 72 73 74 _ Remote control Indicator 71 Home Button Automatic Return to DEMO Mode Charging base 66 FULL amp GO Mode 74 J Remote Control Button amp Indicator Turbo Mode Wi Fi Button Certain Models Only May vary according to model e Tablet Phone not included Fig 1 0 5m Fig 2 Fig 3 Fig 4 Fig 5 PREPARE YOUR CLEANER PACKAGING Do not dispose of your Robo com packaging It may be required in the future for storing or transporting your WARNING When unpacking your and its accessories take care to keep plastic bags away from babies young children and animals to avoid the risk of suffocation Before using your Robo com for the first time you must fully charge it This will take approximately 4 hours Do not expose the main power adaptor or charging station to temperatures below 0 C or above 30 C as this may damag
21. ter drawer tab to open the filter drawer 4 Pull the side of the filter to pop it out of the bracket 5 Gently tap and wash the filter using hand warm water Remove excess water from the filter with a dry cloth and leave to dry 6 Reassemble once completely dry and refit to the Robo com DO NOT use the Robo com without a pre motor filter fitted IMPORTANT Regularly check and maintain the pre motor filter by following the filter maintenance instructions it is also recommended that you purchase new filters after every 3 filter washes This will maintain your Robo com performance CLEANING THE AGITATORS Clean the agitators regularly to maintain maximum cleaning performance 1 Turn Robo com off and remove it from the charging station 2 Turn the Robo com over 3 Rotate the agitators assembly carefully and using scissors cut and remove any tangled threads or hair etc 4 Use the multi purpose cleaning brush to remove any excess dust REPLACING THE AGITATORS Fig 18 Switch the Robo com off and turn it over Use screw driver to loosen agitator holder screw and remove it Remove both agitators Clean the recess where the agitators sit Refit the new agitators ensuring they sit correctly Refit agitator holder and fasten it Certain Models Only May vary according to model Fig 19 Fig 21 Fig 23 Fig 24 CLEANING THE DUST SENSORS Fig 19 The dust sensors are lo
22. th the charging station the charging indicator on charging station will flash The Robo com fail to reach the charging station if there are too many obstacles in between it and the charging station For best results ensure that the charging station is in a wide open space Manual Charging There are several methods to charge your Robo coms A By pressing the Home PAbutton on your remote control By pressing the Home sensitive touch button on your 8 By connecting the mains power adaptor directly to Robo com D By manually placing the Robo com on the charging station E Following the instruction in the Wi Fi Application IMPORTANT The Robo com will not operate without the dust container fitted The Robo com will not operate whilst connected directly to the mains power adaptor Certain Models Only May vary according to model Searching Robo com Google play or APP store REMOTE SET UP Fig 6 To install batteries see cleaner maintenance Replacing the batteries Every time you switch On the robot press the or F button on the main product for 4 seconds to activate the remote control function When this button on the robot is illuminated or when on LCD the indicator appears it means that the remote control function is active and vice versa NOTE The remote control can work through walls because it works on radio waves and not infrared The remote
23. the Move the Remote Control closer to the To check whether the indicator is illuminated referring to remote control set up The Robo com does e sure there are no barriers between the Robo com and automatically charge the charger station The Robo com is very noisy Clean the dust container and filter while cleaning e Check the brushes and drive wheels for dirt and debris Robo com stops working Check the cleaning times set cleans intermittently Robo coms fails to detect Check and clean the sensors stairs Robo com is trapped The Robo com will attempt to free itself but in some cases assist the Robo com manually is not working but e Contact your local Hoover representative there is no error code display The smartphone doesn t Choose theWi Fi Network connect to the Robot Insert the Robot Password that you can get pushing the button on Robot for at least 4 seconds WIFI function doesn t work Check if your WI Fi router is available Check if the APP is correctly installed in your smartphone Check if the Wi Fi icon is illuminated if not please refer to Wi Fi set up Certain Models Only May vary according to model FULL amp GO Fig 29 ERROR CODES The following codes may appear during use or on start up Fig 29 Explanation Er01 Debris trapped in the Edge Cleaning Brush
Download Pdf Manuals
Related Search