DX100 Operating Instructions
Contents
1. have been tampered with neglected modified abused or misused b anyone other than HME employees or authorized HME service representatives provide service on or to the HME Products or c the serial numbers are not intact THIS WARRANTY COVERS HME PRODUCTS AND IS NOT EXTENDED TO ASSOCIATED NON HME PRODUCTS OR ACCESSORIES OR ANY DAMAGE TO HME PRODUCTS CAUSED BY SUCH NON HME PRODUCTS OR ACCESSORIES IN NO EVENT WILL HME BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS ARISING FROM THE USE OF OR INABILITY TO USE ANY HME PRODUCTS OR FROM ACCIDENTS OR ACTS OF GOD HME MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO HME PRODUCTS EXCEPT AS SPECIFICALLY SET FORTH ABOVE This warranty is provided to the original purchaser of the HME Products described on this packing list and is non transferable without the written permission of HME RETURN POLICY ALL SALES FINAL No returns will be accepted except for nonconforming goods as specified above unless HME authorizes such return and unless such return occurs within 90 days of receipt A 15 restocking charge will be assessed on all such authorized returns Authorized returns must be freight prepaid and shall include an authorization number noted on the outside of the package Such authorization number will be provided by HME at the time it authorizes such return All freight sent collect and2. power supply cable connector to the screw connector on the battery charger e Plug the power cable connector into the AC power supply e Plug the power cable into an electrical outlet The red lights on the charger will come on and go off and then the yellow lights will come on and stay on Power supply Power cable To electrical cable connector connector outlet AC40A Battery Charger AC power supply Charge Batteries Up to four batteries can be charged in the battery Charged batteries charger at the same time The battery status lights in storage ports next to each charging port are explained below Up to six fully charged batteries can be stored in the battery storage ports Empty hargi t e Insert a battery in each of four charging ports rele POr until it clicks in place e A yellow light next to each charging port stays on while the port is empty When a battery is in a charging port a flashing yellow light next to it indicates CHARGE PENDING which means the i battery is too hot Adjust the room temperature or Battery in move the charger to a cooler area When a battery is charging port in a charging port a yellow light on steady next to it means CHARGE FAILED If this happens follow the instructions on the side of battery charger e Ared CHARGING light next to a battery port stays on while a battery in the port is charging A green READY light next to a battery port goes on when a battery in the port is ful
3. the Beltpac will function as PTT All Beltpacs can be unlatched by the base station operator by pressing the UNLATCH button on the base station NOTE In HF mode pressing the IC button while latched in ISO will latch on IC Pressing the ISO button while latched in IC will latch on ISO 10 Volume Up Down e Volume Up Adjustment Each time you press and release the volume up A button a beep will be heard in the earpiece as the volume increases one step If you press and hold the volume up button repeating beeps will be heard as the volume steps up to maximum When maximum volume is reached maximum will be heard in the earpiece and will be repeated until you release the volume up button e Volume Down Adjustment Each time you press and release the volume down V button a beep will be heard in the earpiece as the volume decreases one step If you press and hold the volume down button repeating beeps will be heard as the volume steps down to minimum When minimum volume is reached rapidly repeating beeps will be heard Microphone Gain Adjustment Some users talk louder or softer than others To allow for this microphone gain adjustment is provided To increase microphone gain Press the volume up A button while holding down the ISO button in the normal operating mode The microphone gain increase can be monitored through sidetone or preferably by someone else on a Beltpac or at the base station To Decrease micr
4. ECEIVE indicator light Lights green when Beltpacs are transmitting e RESET button Press to reset all communication links or press together with the CLR REG button to clear all Beltpac registrations e REGISTRATION STATUS display Displays 8 briefly when base station power is turned on Indicates status as you register each Beltpac See pages 7 and 8 f f RESET san f a lt REGISTRATION STATUS a e Power PWR button Press and release to turn the DX100 power on Press and hold for 2 seconds to turn power off e Registration REG button Use this button to register each Beltpac used with the DX100 See pages 7 and 8 e UN LATCH button Use this button to unlatch all Beltpac transmitters Users can configure their Beltpacs to latch on in order to talk and listen to each other Base station operators can use the UN LATCH button to stop Beltpac conversations Also if a Beltpac user takes a Beltpac off and leaves it latched on in an unknown location sounds from the area where it is left are picked up by its microphone and transmitted to other Beltpac users This distraction can be stopped by pressing the UN LATCH button on the base station e Clear Registration CLR REG button Use this button to clear Beltpac registrations when needed See page 8 Low Battery Indicator When the DX100 base station battery power is low repeating beeps will be heard in the Beltpac headset and the P
5. HME 400G573 Rev 11 1 05 DX 100 Wireless Intercom Operating Instructions HM ELECTRONICS INC 14110 Stowe Drive Poway CA 92064 USA Table of Contents SECTION 1 INTRODUCTION EQUIPMENT IDENTIFICATION MAIN EQUIPMENT FEATURES Base Station Features Beltpac Features SECTION 2 EQUIPMENT SETUP BELTPAC BATTERY CHARGER SETUP Connect AC Power Supply Charge Batteries BASE STATION SETUP Equipment Connections BELTPAC SETUP AND REGISTRATION Set Up Beltpacs Register Beltpacs SECTION 3 EQUIPMENT OPERATION BASE STATION OPERATION Controls and Indicators Low Battery Indicator BELTPAC OPERATION Beltpac Controls and Indicator Lights Power On Off Enable Hands Free Mode ISO Isolate and IC Intercom Volume Up Down Microphone Gain Adjustment Batteries SECTION 4 TROUBLESHOOTING SECTION 5 TECHNICAL DATA EQUIPMENT SPECIFICATIONS Base Station Illustrations in this publication are approximate representations of the actual equipment and may not be exactly as the equipment appears HM Electronics Inc is not responsible for equipment malfunctions due to erroneous translation of its publications from their original English version 2005 HM Electronics Inc The HME logo and product names are registered trademarks of HM Electronics Inc All rights reserved INFORMATION TO USER This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful
6. OWER light on the base station will be blinking red When this happens replace the batteries in the base station immediately with ones that are new or fully charged as instructed on page 6 NOTE Battery life varies with the type of batteries used With the HME BAT850 NimH battery up to 10 hours can be expected BELTPAC OPERATION Beltpac Controls and Indicator Lights The Beltpac control buttons have a snap action They will activate when pressed firmly Use your fingertips not your fingernails to press the buttons Power On Off Power On Press and release the PWR power button A voice message in the earpiece will say power on and the red lights at the corners of the IC and ISO buttons will go on After a short time one light will go off and the other will change to green indicating the Beltpac is ready for use The REGISTRATION STATUS indicator on the base station will momentarily indicate the ID of the Beltpac Power Off Press and hold the PWR button for approximately two seconds A voice message in the earpiece will say power off and the green light will go off NOTE While a Beltpac is transmitting the appropriate green light will be flashing depending on whether the IC or ISO mode is active If a Beltpac is ready but not transmitting the green light will be on steady Enable Hands Free Mode Push To Talk PTT Mode Setting To set the Beltpac for PTT communication with the power of
7. atch Gaussian filtered FSK TDM 13 ppm Exceeds FCC and ETSI specifications Frequency hopping spread spectrum lt 90dBm w 10 BER 13 ppm lt 2 14 DISPOSAL OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT IMPORTANT Waste Electrical and Electronic Equipment WEEE The European Union EU WEEE Directive 2002 96 EC places an obligation on producers manufacturers distributors and or retailers to take back electronic products at the end of their useful life The WEEE Directive covers most HME products being sold into the EU as of August 13 2005 Manufacturers distributors and retailers are obliged to finance the costs of recovery from municipal collection points reuse and recycling of specified percentages per the WEEE requirements Instructions for Disposal of WEEE by Users in the European Union The symbol shown below is on the product or on its packaging which indicates that this product was put on the market after August 13 2005 and must not be disposed of with other waste Instead it is the user s responsibility to dispose of the user s waste equipment by handing it over to a designated collection point for the recycling of WEEE The separate collection and recycling of waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for re
8. c Battery OPTIONAL EQUIPMENT HS4 3 Single Earpiece amp Lapel Microphone HS14 Single Muff Medium Weight Headset HS14D Dual Muff Medium Weight Headset HS12 Single Earpiece Lightweight Headset HS20 3 Dual Earpiece Lightweight Headset AC850 Battery Charger BATS850 Battery XLR Headset Adapters MD XLR4M Mini DIN to 4 Pin Male MD XLR4F Mini DIN to 4 Pin Female MD XLRSF Mini DIN to 5 Pin Female AC40A Battery Charger MAIN EQUIPMENT FEATURES Base Station Features 10 11 12 ci Di 1 2 3 4 5 6 7 8 1 POWER indicator light 7 UN LATCH button 2 RECEIVE indicator light 8 Clear Registration CLR REG button 3 RESET button 9 Antennas 4 REGISTRATION STATUS display 10 Power connector 5 Power PWR button 11 Battery compartment cover 6 Registration REG button 12 Battery compartment cover release latches Beltpac Features 2 oS 4 2 8 9 Volume up button Headset cable connector Beltpac indicator lights Volume down button ISO Isolate button IC Intercom button PWR Power button Battery Se a Battery release latch Ae cae coe ae SECTION 2 EQUIPMENT SETUP BELTPAC BATTERY CHARGER SETUP IMPORTANT Before installing the system connect the AC power supply to the AC40A Battery Charger and plug it into an electrical outlet Charge all the Beltpac batteries while the other equipment is being installed Charging time is about 2 5 hours Connect AC Power Supply e Attach the AC
9. cycling please contact your local authority your household waste disposal service or the seller from whom you purchased the product
10. ers are assigned sequentially as 0 thru 9 A b C d and E e The power light on the Beltpac next to the IC button will remain on steady green e Repeat Steps 1 to 3 above for each Beltpac to be registered If registration failed A voice message in the headset will say Power on Beltpac Version Begin registration Both power lights on the Beltpac will be blinking red and there may be a delay of up to 90 seconds before you hear Registration failed Press the RESET button on the base station When the REGISTRATION STATUS display becomes blank press the REG button on the base station and register the Beltpac again If registration fails again call your dealer for assistance If you try to register more than 15 Beltpacs An F will appear on the REGISTRATION STATUS display on the base station and you will hear Registration failed in the headset Clear all current registrations by pressing the CLR REG button and the RESET button at the same time Continue holding the CLR REG button after you release the RESET button until the clear code c lower case appears on the REGISTRATION STATUS display Register all active Beltpacs one at a time Previously registered Beltpacs must be re registered SECTION 3 EQUIPMENT OPERATION BASE STATION OPERATION Controls and Indicators e POWER indicator light Lights red when power is on Blinks every 8 10 seconds when the battery is running low e R
11. ette lighter power adapter PN 270 1558 Follow the manufacturer s instructions to connect the external DC power source to the power connector on top of the DX100 Any power supply used with the DX100 should be rated at least 12VDC 500mA Having a fully charged or new battery in its battery compartment when operating the DX100 with AC or external DC power can prevent interruption of communication during a power outage as the DX100 base will automatically switch to battery power BELTPAC SETUP AND REGISTRATION The first time you operate the DX100 system you must register each Beltpac for use with a specific base station The base station will then recognize all registered Beltpacs when their power is on and will know the difference between them and other electronic equipment operating on the same frequencies If a Beltpac is added or replaced later the new one must be registered and the old one remains in memory A maximum of 15 Beltpacs can be registered to a DX100 base station at one time After 15 Beltpacs have been registered you will have to clear all current registrations before registering any additional Beltpacs Follow the instructions below Set Up Beltpacs Before registering them set up all Beltpacs as follows Step 1 Insert a fully charged battery in the Beltpac with the metal contacts on the end of the battery inserted first Press it in until it snaps Step 1 Step 2 Place the Beltpac in the pouch S
12. f press and hold the volume down VW and ISO buttons while you press and release the PWR power button You will hear Hands free off in the headset earpiece Press and hold the IC or ISO button while talking Hands Free HF Mode Setting To set the Beltpac for HF communication with the power off press and hold the volume up A and ISO buttons while you press and release the PWR power button You will hear Hands free on in your headset earpiece When set up for hands free communication the Beltpac can be operated in either HF or PTT NOTE The above settings are saved in memory and only need to be repeated when you want to change between HF and PTT modes When changing modes if both power lights begin blinking turn the Beltpac off and begin again Hands free and PTT mode settings affect both IC and ISO Individual adjustment is not possible ISO Isolate and IC Intercom Use either button to communicate with other Beltpac users Push To Talk PTT Mode Operation press and hold the IC or ISO button while talking In PTT operation audio will be transmitted only while you are pressing the IC or ISO button Hands Free HF Mode Operation Quickly press and release the IC or ISO button to latch the transmitter on Talk and listen as in a normal telephone conversation Press and release the IC or ISO button again to unlatch to end the conversation If either button is held down for more than a half second
13. fy the requirements of Occupational Controlled Exposure Environment for work related use Transmit only when person s are at least the minimum distance from the properly installed externally mounted antenna Hereby HM Electronics Inc declares that the DX 100 is in compliance with the essential requirements and other relevant provisions of R amp TTE Directive 1999 5 EC This product operates in the 2400 to 2483 5 MHz frequency range The use of this frequency range is not yet harmonized between all countries Some countries may restrict the use of a portion of this band or impose other restriction relating to power level or use You should contact your Spectrum authority to determine possible restrictions LIMITED WARRANTY HM Electronics Inc HME warrants the DX 00 for a period of two 2 years from the date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer During the warranty period defective HME Products will be repaired without charge for parts and labor Simply return the defective HME Product with your sales slip as proof of the date of purchase If a defective HME Product is returned prepaid to HME or an authorized HME service center it will be repaired and returned prepaid Replacement of nonconforming goods and repair of defective HME Products are the sole and exclusive remedies available under this warranty This warranty shall be void if a the HME Products
14. ication at one time Others would be listen only until a channel becomes available Power Register Beltpac Reset Unlatch and Clear Registration buttons Registration Status display Power and Receive LEDs External 1 2 wave dipole R TNC connector RX TX horizontal vertical diversity lt 2 64 bit encryption dual slot diversity IEC529 IP Code 4 under battery operation only Frequency hopping spread spectrum 100mW burst Gaussian filtered FSK TDM 13 ppm Exceeds FCC and ETSI specifications over temperature Frequency hopping spread spectrum lt 90dBm w 10 BER 13 ppm lt 2 Beltpac Communication Security System Distortion TRANSMITTER Type Transmit Power Transmission Modes Modulation Type Frequency Stability Harmonics Spurious RECEIVER Type RF Sensitivity Frequency Stability Distortion GENERAL Frequency Range 2400 MHz 2483 5 MHz Antenna Type Internal horizontal vertical diversity Frequency Response 200 Hz to 3 5 kHz Battery Requirements 3 6V lithium ion Battery Life Up to 20 hours Temperature Range 32 122 F 0 50 C Weight 7 4 oz 0 21 kg with battery and pouch Headset Connector 4 pin mini DIN Mic Input Electret microphone Headset Output 160mW into 32Q Controls Power Volume up A Volume down W IC and ISO buttons Indicators Dual color LEDs red green 64 bit encryption lt 2 Frequency hopping spread spectrum 100mW burst Momentary or l
15. ight on the base station will be blinking red When this happens replace the batteries in the base station with new or fully charged batteries as instructed on page 6 11 SECTION 4 TROUBLESHOOTING If you are unable to correct any of the problems described below contact your dealer for assistance e Red light on base station does not come on Be certain power cords are properly connected to base station power supply and electrical outlet If battery operated be certain six AA batteries are inserted in the indicated positions in the battery sled and the sled is installed in the base station See page 6 e Beltpac power lights do not turn green and out of range is heard in the headset Be certain your base station power is on Turn the Beltpac and base station power on and off You may be too far from the base station The range varies with each location s layout If you have more than one base station be sure the Beltpac is registered to the base station it 1s being used with If you are not sure re register it e When trying to register it keeps saying registration failed Refer to If registration failed on page 8 and repeat the registration procedure e Others cannot hear me when I talk Be certain the headset is securely connected to the Beltpac that you are pressing the IC or ISO button on the Beltpac or the microphone gain adjust is turned up to the required level See page 12 2400MHz cordless teleph
16. interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for Class B Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment MANDATORY SAFETY INSTRUCTIONS FOR INSTALLERS AND USERS Use only manufacturer or dealer supplied antennas The Federal Commu
17. ion Turn the sleeve on the cable connector clockwise to secure it to the base station Plug the large female connector at one end of the AC power cord into the power supply Plug the other end of the AC power cord into an electrical outlet Power cable connector AC power supply Sleeve L Antenna Power connector Sleeves Antenna POWER light PWR button Having a fully charged or new battery in its battery compartment when operating the DX 100 with AC or external DC power can prevent interruption of communication during a power outage as the DX100 base will automatically switch to battery power e If using the DX100 with battery power Press in and up on the two battery cover release latches to lift the cover and open the battery compartment Battery cover release latches Push latches in direction of arrows and flip lid up Insert six AA batteries into the battery sled in the positions shown inside the sled and install the sled in the battery compartment as shown below An HME BAT850 Rechargeable Battery may be used instead Battery sled with batteries Close the battery compartment by pressing its cover down until both latches snap in place NOTE Pressing down on the cover next to both of the latches at the same time will assure its proper closing e If using the DX100 with an external DC power source We recommend that you purchase a power cord such as the Radio Shack 12VDC 5A cigar
18. ly charged Store fully charged batteries in storage ports r NOTE The storage ports neither charge nor maintain the batteries They simply provide a place to store the charged batteries until they are needed Yero Reg Gre ep Yero Reg Gre en a a d d FAILED FLASH CHARGE PENDING OR CHARGE PENDING ON NO BATTERY OR CHARGE CHARGING READY ON NO BATTERY FAILED FLASH CHARGE CHARGING READY Batteries should not be left in charge ports after being fully charged If a battery is left in a charge port for more than three weeks the yellow indicator may light up In this case it does not indicate a faulty battery BASE STATION SETUP Locate the two base station antennas and the AC power adapter and power cable received with the base station and connect them to the base station as described below Equipment Connections Step 1 Connect the two enclosed antennas to the antenna connectors on the top and right side of the base station shown to the right Position the antennas at right angles to each other The illustration below shows one possible arrangement Turn the sleeve on each of the antenna connectors clockwise to tighten the antennas securely in position Antenna connectors Step 2 Note which of the following applies to you If using the DX100 with AC power Plug the connector at the end of the AC power supply cord into the power connector on top of the base stat
19. nications Commission has adopted a safety standard for human exposure to RF Radio Frequency energy which is below the OSHA Occupational Safety and Health Act limits The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met Base Station Antenna minimum safe distance 7 9 inches 20 cm at 100 duty cycle Base Station Antenna gain This device has been designed to operate with an antenna having a maximum gain of up to 2dBi Antenna mounting The antenna s used for the base transmitter must be installed to provide a separation distance of at least 7 9 inches 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter Antenna substitution Do not substitute any antenna for the one supplied by the manufacturer or radio dealer You may be exposing person or persons to excess radio frequency radiation You may contact your radio dealer or the manufacturer for further instructions WARNING Maintain a separation distance from the base station transmit antenna to a person s of at least 7 9 inches 20 cm at 100 duty cycle You as the qualified end user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance above is maintained between the antenna and nearby persons for satisfying RF exposure compliance The operation of this transmitter must satis
20. one interference If there is a 2400MHz cordless telephone nearby interference may occur However because the DX100 is a frequency hopping system this problem is unlikely If it does occur changing frequencies on the telephone may alleviate the problem If not move the phone as far as practical from the base station or use another type phone In the event of an electrical power outage such as from a lightning storm or power generator failure if you experience problems with your HME equipment after the electricity comes on again unplug the AC power supplies from their electrical outlets remove any batteries and wait 15 seconds then plug them back in 12 SECTION 5 TECHNICAL DATA EQUIPMENT SPECIFICATIONS Base Station GENERAL Frequency Range Frequency Response Power Requirements Temperature Range Size Weight of Beltpacs per Base Front Panel Controls Front Panel Indicators Antenna Type System Distortion Communication Security Splash Resistant TRANSMITTER Type Transmit Power Modulation Type Frequency Stability Harmonics Spurious RECEIVER Type RF Sensitivity Frequency Stability Distortion 2400 2483 5 MHz 200 Hz to 3 5 kHz 100 240V AC 50 60Hz or 12 14VDC 32 122 F 0 50 C 10 2 x 6 45 x 3 33 1 RU 25 91 x 16 38 x 8 46 cm 2 35 Ibs 1 07 kg maximum 15 can be registered Any 4 can have simultaneous full duplex commun
21. ophone gain Press the volume down V button while holding down the ISO button in the normal operating mode The microphone gain decrease can be monitored through sidetone or preferably by someone else on a Beltpac or at the base station NOTE You will hear Maximum if you attempt to go higher than maximum microphone gain You will hear beeps if you attempt to go lower than minimum microphone gain Microphone gain will be saved in non volatile memory and does not require readjustment each time the power is turned on Batteries Change Beltpac Batteries When a Beltpac battery becomes weak a voice in Battery Battery the earpiece will say Change battery When this release latch happens take the Beltpac out of its pouch and remove its battery Slide the arrow shaped battery release latch in the direction of the arrow Pull up on the end of the battery near the battery release latch and lift the battery out of the Beltpac or turn the Beltpac over and catch the battery in your hand When replacing a battery in the Beltpac place the end of the battery with the metal contacts into the battery holder on the Beltpac in the same position as the battery you removed Press the top of the battery carefully into the battery holder until it snaps in place under the battery release latch Change Base Station Batteries When a base station battery becomes weak repeating beeps will be heard in the Beltpac headset and the POWER l
22. packages without an authorization number will be refused and returned to sender Exceptions The BAT40 and BAT850 Batteries and the HS14 HS14D and HS20 3 Headsets are warranted for one year The HS4 3 Earpiece is warranted for 90 days SECTION 1 INTRODUCTION The DX100 provides private secure communication Each base station can have up to fifteen Beltpacs registered to it Four of the fifteen Beltpacs can transmit at the same time Beltpacs can be used either in the push to talk or hands free mode The base station operator can stop any Beltpac from transmitting The base station can be operated using standard AC electricity an external DC power source or six AA batteries A power supply cable and a battery sled are included with the base station System Usage Example Stage Manager House Manager Director DX100 Spot Light Sound Props This is an example of a typical theatrical application A variety of other uses for the DX100 are possible EQUIPMENT IDENTIFICATION The following equipment is standard with the DX100 Wireless Intercom System As you unpack the equipment check the packing list to be sure you received all items listed Base Station Battery Sled Base Station Antennas BS100 Base Station 2 per Base Station 115 230 Volt AC Power Supply 1 per Base Station with Power Cables 1 per AC40A Battery Charger with Power Cables Beltpac Pouch BP200 Beltpac Beltpa
23. tep 3 Plug the headset cable connector into the Beltpac Register Beltpacs Beltpacs must be within 6 feet 1 83 meters of the base station while you are registering them Be certain the base station power is on and each Beltpac you are going to register is turned off before you begin Beltpacs that are already registered can be on or off Step 1 Put the headset of the Beltpac being registered on your head Step 2 Press the REG registration button on the base station e The REGISTRATION STATUS display on the base station will show a small o for open NOTE If you wait too long before going on to Step 3 the base station will go out of the registration mode and you will have to repeat Step 2 Step 3 Press and hold the ISO button on the Beltpac while you press and release the PWR power button to turn the unit on then release the ISO button This will cause the Beltpac to enter the registration mode e The two power lights at the corners of the Beltpac near the IC and ISO buttons will begin blinking red then will blink green two or three times and go off e Wait There may be a short delay If registration is successfully completed e A voice message in the headset will say Power on Beltpac Version Begin registration Registration complete e After a delay of up to 15 seconds the REGISTRATION STATUS display will show the ID number assigned to this Beltpac for about 10 seconds NOTE ID numb
Download Pdf Manuals
Related Search