User Manual
Contents
1. ell e ul 7 02 gt 02 0522 oL 2 Ex 5 o Es 250 UJ m ON WE 5 SE O D gt IR Out RS 232 Link e will page 4 Introduction Description 1 Power This LED indicator will glow bright blue and will remain illuminated as long as the power supply is connected to the Receiver unit See Power LED Status page 10 for details on LED status messages o 7 25 72 o gt oO 2 HDMI Connect an HDMI cable between this port an Ultra HD display 3 IR Ext Connect the included IR extender to this port It will not work with the electrical IR connection from an automation control device 4 IR Out Connect an IR emitter Gefen part no EXT IREMIT from this port to the IR sensor _ of the device to be controlled 5 RS 232 Connect an RS 232 cable from this port to the RS 232 device to be controlled 6 Link Connect a shielded CAT 5e cable or better up to 495 feet 150 meters from this port to the Link port on the Sender unit page 5 Installation Connection Instructions Video 1 Connect the included HDMI cable between the Ultra Hi Def source and the HDMI port on the Sender unit Getting Started 2 Connect Ultra HD display to the HDMI port on the Receiver unit using another HDMI cable Networ2. Geesen TOOLBOX AKULTRA HD ELR POL Extender w RS 232 and 2 way IR GIB UnmMDZIRS ELRPOL BLEK User Manual 1 9GEFEN 9GEFEN 3 TOOLBOX si TOOLBOX a 8 3 A 5 4 3 A 5 4K Ultra HDS 2 4K Ultra HD ELR POL Extender ELR POL Extender w RS 232 and 2 Way IR w RS 232 2 Way IR Important Safety 18581968685 10 11 12 13 14 15 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this product near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install or place this product near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety Ifthe provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified b
3. Surface mountable Home 4080 HIGH DEFINITION MULTIMEDIA INTERFACE PROGRESSIVE 60Hz 4 2 0 4 2 APR HoOmMilzo 22 E 627 NZ DCI 4096 x 2160 Deep Color Support vi itures and Packing List Packing List The following items are shipped with the 4K Ultra HD Extender w RS 232 and 2 way IR If any of these items are not present in the box when you first open it immediately contact your dealer or Gefen 1 x 4K Ultra HD Extender w RS 232 and 2 way IR Sender unit 1 x 4K Ultra HD Extender w RS 232 and 2 way IR Receiver unit 1x6 ft locking HDMI cable M M 1x6 ft DB 9 cable MEI 1 x IR extender 1 x IR emitter 1 24V DC locking power supply 1 x Quick Start Guide vii Table of Getting Started Introduction 2 Sender Unit RTI 2 IST A Installation exceso cura oeste Ever CEN EECa TeaTS 6 Connection Eder e 6 Sample Wiring Diagraim conor rrr err rer eret rerit Basic Operation Ewe ansehen 10 A A P 10 Receiver unit CE rasa 11 CONTO ME 12 Controlling the Source from the Viewing Location 12 Controlling the Display from the Source Location 13 DIP Switch EE 14 NENT le BEE 14 Appendix Surface MOUNTING InStructiONS ek 18 Network Cable e REN 19 ele EE 20 WING OX EE 21 viii 4K ULTRA HD 60Hz 4 2 0 ELR POL Exte
4. 2015 Gefen LLC All Rights Reserved All trademarks are the property of their respective owners Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice cc o 0 This product uses UL listed power supplies Features and Packing List Features Extends AK Ultra HD 3840 x 2160 60 Hz 4 2 0 or 30 Hz 4 4 4 and Bi Directional IR up to 130 feet 40 meters over a single CAT 5e or CAT 6 cable Extends Ak Cinema DCI 4096 x 2160 30 Hz 4 4 4 Ethernet RS 232 and Bi Directional IR over a single CAT 5e cable up to 330 feet 100 meters 8 bit color Extends HDMI at 1080p Full HD Ethernet RS 232 and Bi Directional IR over a single 5 cable up to 330 feet 100 meters up to 12 bit Deep Color Extends HDMI at 1080p Full HD Ethernet RS 232 and Bi Directional over a single 5 cable up to 495 feet 150 meters 8 bit color HDMI Features Supported HDCP 2 2 and 1 4 12 bit Deep Color LPCM 7 1 audio Dolby TrueHD and DTS HD Master Audio pass through 3DTV pass through CEC pass through Lip Sync pass through RS 232 Extension 2 way extension from Sender to Receiver and from Receiver to Sender Gefen POL feature provides power to the Receiver unit over the link cable Uses Gefen s implementation of HDBaseT technology EDID pass through Locking power connector
5. Solid blue Link is established between Sender Receiver unit Sender unit is receiving the source signal Flashing xl Non HDCP content is being received by the blue orange Sender unit Solid orange Sender unit is not receiving source signal from the source device Source is not connected Check the cable between the Sender unit and the source device page 10 Power LED Status Receiver unit LED Status Description Basic Operation Off e Receiver unit is not receiving power from Sender unit Inspect CAT 5 cable between Sender and Receiver unit Solid blue Link is established between Sender and Receiver unit 9 Receiver unit is powered and is receiving the source signal from the Sender unit Flashing Non HDCP content is being transmitted to the blue orange 2 x Receiver unit Solid orange Receiver unit is not receiving source signal from the Sender unit Inspect the CAT 5 cable between the Sender and Receiver unit page 11 Basic Operation IR Control Controlling the Source from the Viewing Location 1 Connect the included IR extender to the IR Ext port on the Receiver unit 2 Connect the included IR emitter from the IR Out port on the Sender unit to the IR sensor on the source device 24 Ultra HD source IR emitter to IR Out port HDMI cable Sender unit E Fl up to 4
6. extended to a maximum distance of 495 feet 150 meters Color depth is limited to 8 bit color OFF 1 This is the default setting Allows all resolutions up to 4K x 2K to be extended up to 330 feet 100 meters 1080p Full HD up to 12 bit Deep Color page 14 AKULTRA HD ELR POL Extender w RS 232 and 2 way IR Appendix Surface Mounting Instructions The Sender and Receiver units can be mounted on any flat surface as shown below screws not included There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the HDMI cables Appendix For installation on a drywall surface use a 6 drywall screw When installing it is recommended to use the center hole on a stud page 18 Network Cable Diagram Front of RJ 45 Connector Appendix 1234567 8 Gefen recommends the TIA EIA 568 B wiring option Use the following table when terminating cables in the field Orange White TD Transmit Data positive differential signal Orange TD Transmit Data negative differential signal Green White RD Receive Data positive differential signal Blue Unused Blue White Unused Green RD Receive Data negative differential signal Brown White Unused Brown White Unused Om Go Information page 19 Specifications Supporte
7. 5 long reach mode See DIP Switch Configuration Mounting Instructions 78 Network Cable Diagram 79 Operating Notes v Packing List vii Power LED indicator 3 5 receptacle 3 Power LED Status 70 Receiver unit 4 LED status 11 RS 232 port 3 5 Safety Instructions Sender unit 2 LED status 10 Specifications 20 Table of Contents viii Technical Support iv Warranty Information iii Wiring Diagram 7
8. 95 feet 150 meters ml HDMI cable Shielded CAT 5e cable or better IR extender to Ultra HD display to IR Ext port IR signals page 12 Basic Operation IR Control Controlling the Display from the Source Location Connect the 3 5mm connector from the IR In port on the Sender unit to an automation system with electrical IR output Connect the included IR emitter from the IR Out port on the Receiver unit to the IR sensor on the display from Automation System to IR In port Sender unit from Ultra HD source HDMI cable Shielded 5 cable or better up to 495 feet 150 meters 6 Receiver unit HDMI cable IR emitter to IR Out port Ultra HD display gt IR signals page 13 Basic Operation DIP Switch Configuration Distance Setting This product passes through the display s EDID to the source If the display is capable of accepting Deep Color the source must be manually configured to output 8 bit color This is only applicable when using 4K x 2K resolutions and long run modes The distance setting is controlled using a DIP switch on the bottom of the Receiver unit Bottom of Receiver unit E 7 ON d Position Description ON Allows resolutions up to 1080p Full HD to be
9. d Formats Video 4K x 2K 1920 x 1200 WUXGA 1080p Full HD Audio 7 1 Linear PCM Dolby TrueHD DTS HD Master Audio 2 9 i Connectors Indicators and Controls HDMI Sender 1x HDMI Type A 19 pin female HDMI Receiver o 1 x HDMI Type A 19 pin female Link Sender Receiver 1 x RJ 45 shielded female IR In Sender Receiver gt 1 3 5mm female IR Out Sender Receiver 1 x 3 5mm female RS 232 Sender lt 1x DB 9 male RS 232 Receiver 1 x DB 9 female Power Sender 5 1 x 4 pin female Power Indicator Sender Receiver 1 x LED blue DIP switch Receiver 1x DIP switch Maximum Pixel Clock 300 MHz Maximum TMDS Clock 300 MHz Input Video Signal 1 2 Volts p p Input DDC Signal 5 5 Volts p p TTL Power Input 24V DC Power Consumption 10 Watts Operating Temperature 32 to 122 F 0 to 50 C Physical Dimensions W x x D 4 3 x 1 x 3 2 Sender Receiver 110mm x 26mm x 80mm Unit Weight 0 35 Ib 0 2 kg page 20 c E 5 a D Connection Instructions 6 DIP Switch Configuration 74 Distance setting See DIP Switch Configuration Features vi HDMI port input 3 port out 5 Installation 6 IR Control 72 controlling the display 13 controlling the source 12 IR Ext port 5 IR In port 3 IR Out port 3 5 LED Status 70 Link port 3
10. gistration Register your product here http www gefen com kvm Registry Registration jsp Operating Notes Shielded 5 or better cables should always be used The 4K Ultra HD Extender w RS 232 and 2 way IR will extend 1080 Full HD up to 330 feet 100 meters in Deep Color or 1080p Full HD up to 495 feet 100 meters in 8 bit color 4K x 2K resolution can be extended up to 330 feet 100 meters See Distance Setting page 14 for more information Power Over Line POL is a Gefen proprietary technology that provides power to the Receiver unit over a single shielded CAT Be or better cable The included power supply can be connected to either the Sender or Receiver unit This product passes through the display s EDID to the source If the display is capable of accepting Deep Color the source must be manually configured to output 8 bit color This is only applicable when using 4K x 2K resolutions and long run modes See Distance Setting page 14 for more information In port on the Sender unit is designed to accept electrical IR connection from third party automation devices It will not work with Gefen IR extenders The Ext port the Receiver unit is designed to work with the Gefen EXT RMT EXTIRN extender It will not work with the electrical IR connection from an automation control device 4K Ultra HD Extender w RS 232 and 2 way IR is a trademark of Gefen LLC
11. k cable 3 Connect a shielded CAT 5e or better cable up to 495 feet 150 meters from the Link port on the Sender unit to the Link port on the Receiver unit Information IR 4 Refer to IR Control page 12 for details on connecting IR devices gt RS 232 5 Connect the included RS 232 cable from the automation device to the RS 232 port on the Sender unit 6 Connect an RS 232 cable from the RS 232 port on the Receiver unit to the device to be controlled gt Power 7 Connect the included 24V DC power supply to the power receptacle on the Sender unit 8 Connect the opposite end of the power supply to an available electrical outlet page 6 Getting Started Installation Sample Wiring Diagram 19 TOOLBOX 4K Ultra HD Source Automation Device IR Input IR Emitter Sender Information CAT 5e CABLE ze Up t0495 f HDMI CABLE rg IR mmm RS 232 CABLE ron RS 232 Controlled Device 4K Ultra HD Display Receiver IR Extender IR Emitter GTB UHD2IRS ELRPOL BLK page 7 4K ULTRA HD 60Hz 4 2 0 ELR POL Extender w RS 232 and 2 way IR A Basic Operation Basic Operation Power LED Status The Power LED indicator on the Sender and Receiver unit provides basic information on the current status of the 4K Ultra Extender w RS 232 and 2 way IR Sender unit LED Status Description Off O Sender unit is not powered Check the power supply
12. nder w RS 232 and 2 way IR 1 Getting Started Introduction Sender unit ES Ie 5 oll Getting Started 4 24 A na gt cz og i v WE eier 9 16 IR Out RS 232 Link J page 2 Introduction Description 1 24V DC Connect the included 24V DC power supply to this power receptacle 2 Power This LED indicator will glow bright blue and will remain illuminated as long as the power supply is connected to the Sender unit See Power LED Status page 10 for details on LED status messages o 7 72 o 2 gt 3 HDMI Use the included HDMI cable to connect an Ultra Hi Def source to this HDMI port 4 IR In Connect a mini mono 3 5mm cable from this port to an automation system with an electrical IR output It will not work with Gefen IR extenders 5 IR Out Connect the included IR emitter from this port to the IR sensor of the device to be controlled 6 RS 232 Connect the included RS 232 cable from this port to the automation device 7 Link Connect a shielded CAT 5e cable or better up to 495 feet 150 meters from this port to the Link port on the Receiver unit page 3 o 7 72 gt 7 Introduction Receiver unit
13. to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty Customers outside the US are responsible for shipping charges to and from Gefen Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com Contacting Gefen 7 22 Technical Support 818 772 9100 800 545 6900 8 00 AM to 5 00 PM Monday Friday Pacific Time Fax 818 772 9120 Email support gefen com Web http www gefen com Mailing Address Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 Product Re
14. y the manufacturer To reduce the risk of electric shock and or damage to this product never handle or touch this unit or power cord if your hands are wet or damp Do not expose this product to rain or moisture Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged any way such as power supply or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Batteries that may be included with this product and or accessories should never be exposed to open flame or excessive heat Always dispose of used batteries according to the instructions Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment
Download Pdf Manuals
Related Search