Operation manual - Compound Security Systems
Contents
1. ALPHA ARSENAL ALPHA ARSENAL ALPHA ALPHA ARSENAL ALPHA ARSENAL ALPHA ALPH POLUS GSM Door Window Sensor WIRELESS PROTECTION FOR YOU AND YOUR FAMILY Operating Manual POLUS GSM WIRELESS MAGNETIC SECURITY DOOR WINDOW SENSOR OPERATING MANUAL CONTENTS 1 DESCRIPTION AND OPERATION 1 1 Function 1 2 Security Alarm Sensor Device Package Contents 1 3 Technical Specifications 1 4 Security Alarm Sensor Structural Design 1 5 Magnet Design 1 6 Keychain Magnet Design 1 7 Function and Operation of the Security Alarm Sensor 2 SET UP PROCEDURE 2 1 Preparing and Operating the Alarm Device 2 2 Configuring the Alarm Device 2 3 Accessing the Programming mode 2 4 Setting up for the First Time Use 2 5 Verifying set up 2 6 Changing amp Adjusting the Parameters 2 7 Security Alarm Sensor Device Installation 3 TROUBLESHOOTING 4 CONTACT INFORMATION 1 DESCRIPTION AND OPERATION 1 1 Function The POLUS GSM Security Alarm Sensor Device is designed and made to detect the unauthorized opening of doors windows and hatches etc and when triggered to transmit an SMS alert notification and or place a call to the owner s telephone The alarm device supports the following operational modes Programming Disarmed ArmDelay Armed On Guard Active AutoArm Delay Alarm Standby NotDelay POLUS GSM Security Alarm Sensor Device FEATURES Installs at any location with mobile GSM re2. 1 isms 000 1st telephone Enter number in the number following format primary for pL notification e g 17180000000 2 2sms 000 Telephone Enter number in the 3 3sms 000 numbers for following format 4 4sms 000 notification LEER Es 5 Ssms 000 e g 17180000000 6 6sms 000 7 BALANS 0 Remaining Auto detection of balance Inquiry remaining balance USSD tel number Manual entry of tel e g 1004 13 14 TEST 7 Frequency for Sets frequency for test status test status SMS SMS notifications notifications Interval sets up to 250 days E g 1 Notification once a day 7 Notification once a week 0 Notification not sent 16 ArmDisarm 1 Send SMS 0 Do not send when armed 1 Send disarmed mode activated 17 AutoArm 60 Reset time Interval parameter pause interval must be between 0 after a 250 seconds triggered e g 60 60 sec Alarm After after Alarm sending Alarm notifications notifications complete and no the Alarm additional violations Sensor pauses occur the Alarm for up to 250 Sensor will enter seconds Armed On Guard checks for the mode presence or absence of additional violations and if absent will Arm A notification that the Alarm Sensor has re armed is not sent 18 AlarmNot 1 Alarm 0 Only SMS to notificatio Isms 6sms n Option Type during Alarm mode 1 Call SMS SMS sent to isms then calls placed to all tel numbers followed by
3. SMS transmittal to all 14 remaining tel numbers 2sms 6SMS 3 Only calls placed to lsms 6sms 19 ArmDelay 30 Arming delay in Parameter in Seconds seconds between 0 250 sec 20 NotDelay 40 Notification Parameter should delay be between 0 250 after triggered sec alarm in order to allow disarming in seconds 25 TriggerAlarm 0 Turns Alarm 0 on Sensor sound 1 Off off on during triggered alarm 34 POLUS 0 Template name 0 w settings 35 mnum 000 For operation SIM Tel Alarm w Polus GSM Sensor Security Panel application 36 Lang 0 Notification 0 Ru Language 1 En 37 EXTIN 0 Link up 0 No Ready to external Link up external sensors Arming Button Switch only1 or 2 Yes Link up diagram see 1 7 8 Operating service parameters amp values settings created in template during Polus GSM Security Alarm Sensor set up 2 3 Accessing the Programming Mode In order to access Programming mode consecutively execute the following actions 1 Install the SIM card as shown in diag 7 Caution Prior to installing or removing the SIM card it is necessary to de activate the Alarm Sensor electrical supply i e install the protective plastic insert or remove the battery 15 the protective plastic insert Battery Power SIM Card SIM Source Installation Card K3 Protective plastic insert Diag 7 SIM
4. any changes to the settings In the absence of an incoming call SMS the Security Alarm Sensor at the expiration of 1 one minute enters Disarmed mode In the event of an incoming call SMS occurring and being accepted the Security Alarm Sensor at the expiration of 1 one minute will enter Disarmed mode and will transmit an SMS notification reflecting the changed settings to the primary telephone number 16 2 4 Setting up for the First Time After powering up the Security Alarm Sensor a template with cells containing default values will be created on the SIM card phone book in accordance with Chart 4 At a later time you are able to edit these parameters and values It is necessary to record notification telephone numbers to the SIM card Perform the followings steps consecutively 1 Access Programming mode in the device see item 2 3 2 Begin by calling the Security Alarm Sensor SIM card telephone number from the telephone number that will be used as the primary notification number After receiving and recording the number the Security Alarm Sensor will disconnect the call and emit 1 one audible confirmation beep This number will be recorded in cell 1 1SMS see Chart 4 and as the designated primary number will be sent an SMS notification from the Security Alarm Sensor indicating Setting Reset Number Added 1xxxxxxxxxx 3 Proceed to record any additional notification telephone numbers by c
5. card installation protective plastic insert removal 2 Remove the Protective Plastic Insert from in between the contacts and the battery see diag 7 or install a battery using correct polarity if it had been previously un installed 3 The Security Alarm Sensor light diode indicator will glow red The GSM light diode will glow for 3 seconds and will begin flash quickly 4 Wait for the SIM card to register on to the network At the conclusion of registration 3 beeps will be heard and the GSM light diode will flash 1 once every 4 four seconds The Security Alarm Sensor light diode indicator will glow green This indicates that the Security Alarm Sensor has entered the Programming mode During the entire duration of the Programming mode the light diode indicator will glow green In the event the GSM light diode continues to flash quickly the SIM is not registering on the network might be due the SIM card being incorrectly or not installed blocked by a PIN code or the GSM network is inaccessible take action in accordance with Chart 5 Upon entering the Programming mode the Security Alarm Sensor sends an SMS notification with settings to the primary notification telephone number if the primary number was previously recorded in the SIM card memory For the span of 1 one minute the Security Alarm Sensor remains in Programming mode and stands by for an incoming call and or SMS containing
6. indicates 1 the primary notification number will be sent an SMS containing the text Armed or Disarmed by a call from see Diag 6a 6b If while in Armed On Guard mode a violation is detected and the Notification Delay time span expires default setting of 40 seconds see Chart 4 cell 20 the Security Alarm Sensor will transmit Alarm SMS messages see diag 8 and or will execute calls to the registered telephone numbers depending on the notification parameter selected see Chart 4 cell 18 In case the Notification Delay time span is set to between 0 20 seconds the Security Alarm Sensor will without any additional delay proceed to execute notifications because the Notification Delay time span includes the time required for the GSM module to power up and for the SIM card sign on to the network The required time for GSM module power up and SIM card network sign on is 10 30 seconds After the Security Alarm Sensor concludes transmitting Alarm notifications it stands by to receive incoming calls from numbers 1SMS 6SMS in order to Disarm Upon receiving an incoming call the Security Alarm Sensor will reset the call transmit an SMS to the primary number containing Disarmed by a call from 1xxxxxxxxxx when value 1 is indicated in the ArmDisarm cell location and will then enter Disarmed mode In the event there is no incoming call received within
7. 60 seconds after the notification delay cycle concludes default setting see Chart 4 cell 17 and there is no further violation door closed the Security Alarm Sensor will enter Armed On Guard mode 11 1 7 8 Operating the Security Alarm Sensor using External Alarm Sensors If necessary external magnetic alarm sensors further referred to as external sensors one or more or any other device that generates an Alarm signal via the opening of contacts can be connected to the Security Alarm Sensor When operating the Security Alarm Sensor unit with external sensors in Settings Chart 4 cell 37 it is necessary to select value 1 or 2 When operating the Security Alarm Sensor unit with external sensors arming is limited to using the keychain remote arming via an external button switch is not available 1 7 8 1 If value 2 is indicated in cell 37 an Alarm signal will be generated when any of the sensors either an external sensor or the Security Alarm Sensor is triggered Link up diagram see diag 6a 1 7 8 2 POLUS GSM Detection san Sensor Sensor Sensor Bia wie i Misa O N Diag 6a Link up diagram for External Sensors Switches Value 2 cell 37 1 7 8 3 Indicating value 1 cell 37 allows for two link up operating options Option 1 The Security Alarm Sensor is installed without a magnet i e it does not operate as a magnetic detection sensor see diag 6b The Alarm signal
8. Armed On Guard mode when a violation is detected e g the opening of a door etc the Security Sensor Alarm will enter NotDelay mode for a span of 0 250 seconds Notification Delay Chart 4 Cell 20 In the event of an authorized opening during the NotDelay countdown time span the Security Sensor Alarm can be Disarmed by calling from one of the six notification telephone numbers previously programmed into the Security Sensor Alarm SIM card the Security Sensor Alarm will then enter Disarmed mode In the event of an unauthorized opening violation after the Active AutoArm Delay time span has expired the Security Sensor Alarm will enter Alarm mode and will proceed to send notifications via SMS and or calls After the initial standby AutoArm of 0 250 seconds expires Chart 4 Cell 17 the Security Sensor Alarm will exit Alarm mode and will enter Standby NotDelay mode While in this mode and with no additional violations e g the door closed the Security Sensor Alarm will enter Armed On Guard mode While in Alarm and Standby NotDelay modes it is possible to disarm the Security Sensor Alarm by a call from a mobile telephone After being called the Security Sensor Alarm will enter DisArmed mode 1 7 5 Security Alarm Sensor Indicators The Security Alarm Sensor has built in light and sound indicators In addition the GSM light diode indicates GSM si
9. alling from them and after each additional number is recorded an SMS notification is sent to the primary telephone number containing Number Added 1zzzzzzzzzz Number Added 12zzzzzzzzzz etc 4 One 1 minute after the last call is received the Security Alarm Sensor will transmit an SMS containing the settings to the primary telephone and will then enter Disarmed mode If you were unable to record all the necessary additional notification telephone numbers either put in the Protective Plastic Insert between the battery and contacts or remove the battery wait 2 two minutes and repeat the procedure from the beginning see item 2 6 1 Primary notification number Received from 1YYYYYYYYYY Security Alarm Sensor 14 Frequency of 7 Balance Inquiry test status Notifications 1 1XXXXXXXXXX 7 100 ta ei l 16 Send SMS Arm Disarm 14 1 16 1 17 60 18 1 19 30 option 17 Alarm Reset Time Pause 20 40 25 0 36 1 37 0 SNN 19 Arming Delay 20 Notification Delay 36 Notification language 25 Alarm Sensor Alarm Sound On Off Signal Strength 37 Connect External Sensors Diag 8 Sample SMS with Settings 17 2 5 Verifying Set up Bring the Keychain magnet up to the Security Alarm Sensor to be armed see diag 3 amp 9 For 30 thirty seconds the Security Alarm Sensor will emit audible chirps Within this time span it is necessary to locate the Magnet in proximity to the Security Alarm Sensor as shown in the insta
10. ception Arms via a key chain magnet and or an optional external button switch optional external button switch not included in the package Disarms via a mobile telephone during Active AutoArm Delay Alarm or Standby NotDelay modes Automatically re arms to On Guard mode after a triggered Alarm Settings programmable via mobile telephone online and thru utilizing Configurator Express GSM Android amp iOS apps Expandable to link up with external magnetic security sensors or with any device that triggers an alarm signal via the opening of contacts Operates on a single 3 volt CR123 lithium battery for up to 12 months Built in power saving economy mode option available by disabling SMS armed disarmed notifications Automatically detects remaining balance inquiry telephone number The device is designed to operate indoors and guard around the clock 24 7 in stable non extreme conditions 1 2 Package Contents Include In accordance with chart 1 Chart 1 Contents POLUS GSM Magnetic Security Alarm 1 one Sensor Device Magnet 1 one Lithium CR123A 3V battery 1 one Keychain magnet 1 one User s manual 1 one 1 3 Technical Specifications In accordance with chart 2 Chart 2 Primary Technical Specifications DESCRIPTION VALUE Gap between the Security Alarm Sensor amp Magnet at which an Active Notdelay or an Alarm signal is gene
11. e indicator Cover body 3 y ait Guide mark Diagram 1 Security Alarm Sensor device design General view Top view Light diode indicator Diagram 2 Security Alarm Sensor device design Top amp bottom view ounting holes The controller circuit board refer to diagram 3 contains magnetic sensors the primary sensor detection sensor DD1 amp the arming sensor DD2 battery holder GB1 audio indicator BQ1 two color light diode indicator VD1 and a terminal block X2 in order to connect an external arming switch or additional optional external wired sensors The two color light diode indicates the state of the Security Alarm Sensor device in accordance with chart 3 The GSM module circuit board contains a SIM cardholder XS3 and a GSM light diode to indicate network signal strength module GSM Diagram 3 Exposed view of the controller circuit board and GSM module The Security Alarm Sensor device is shipped with an installed battery insulated from the contacts by a protective plastic insert refer to diagram 7 1 5 Magnet Design The Security Alarm Sensor device includes a magnet diag 4 The magnet unit consists of the base and cover body A permanent magnet is installed in the cover body and is firmly snapped on to the base The cover body and base unit are made of ABS plastic Diagram 4 Exposed View of the Magnet Unit The Security Alarm Sensor device
12. e number Test status SMS notifications are sent depending on selected interval Chart 4 Cell 14 The interval time reference point starts with the receipt of the settings notification When an Alarm is triggered the Security Alarm Sensor will transmit an SMS notification place a call to the first registered primary number and will then place calls to the remaining numbers together with transmitting SMS notifications The Security Alarm Sensor will cease calling one number and will continue to call the next number under the following circumstances When the subscriber does not pick up within 30 seconds When the subscribers line is busy When the subscriber is not connected to a network Calling out will cease after one of the subscriber numbers picks up and disconnects then the Security Alarm Sensor will transmit Alarm Diag 5c notifications to the numbers located at 2SMS 6SMS 2 Armed SNN Diag 5a SMS Armed 2 Disarmed by a call from 1XXXXXXXXXX SNN Diag 5b SMS Disarmed by a call from 2 Alarm SNN Diag 5c SMS Alarm S indicates network signal level NN indicates network signal level as a percentage e g S50 S75 etc The value indicating network signal level SNN is included in all SMS notifications except for notifications containing remaining SIM card balance 1 7 7 Arming and Disarming Protecting the premises by arming the Security Alarm Sensor i
13. gnal strength Indicator descriptions can be found in Chart 3 Chart 3 Security Alarm Sensor Indicators Event Mode Light Indicator Sound Indicator GSM Light diode Indicator Power On Glows Red Glows Red 3 Sec GSM Network Glows Red Flashes for 20 40 Search Sec GSM Network Flashes Red Green 3 Beeps Once every 4 sec Activation At Start up Programming Mode Glows Green Security Alarm Audio Beep Sensor Incoming Call or SMS Disarmed Mode ArmDelay Mode 1 Beep per sec Armed On Guard Mode during Delay Span Operating Mode Verification Using Keychain Magnet Button Switch In Armed On Guard Mode Glows Green Short Audio Chirp Attention Error Mode During GSM Network Search Glows Red AutoArm Delay Mode Flashes Green Alarm Mode Flashes Red Audio Beeps 3 per sec Standby NotDelay Mode 1 7 6 Notifications The Security Alarm Sensor transmits an armed disarmed Diag 5a amp 5b status SMS notification to the number 1 primary telephone registered to receive notifications 1SMS see Chart 4 and Alarm notifications to ISMS 6SMS registered at 1SMS will also receive SMS notifications containing selected settings Item 2 4 diag 8 and Test status SMS notifications showing the numbers remaining SIM card balance registered at Diag 5b Th
14. he following functions arms the Security Alarm Sensor cancels arming the Security Alarm Sensor during active ArmDelay mode from 15 to 250 seconds depending on selected setting refer to Chart 4 cell 19 verification of the Security Alarm Sensor operating mode Armed On Guard mode or Disarmed mode 1 7 4 Operating modes of the Security Alarm Sensor Upon activating power by either removing the protective plastic insert from in between the battery and contacts or by inserting a battery the Security Alarm Sensor enters programming mode one 1 minute after set up programming concludes the Security Alarm Sensor enters Disarmed mode Upon arming using the Keychain Magnet or an optional external button switch the Security Alarm Sensor enters Arming mode for a span of 15 to 250 seconds ArmDelay Chart 4 Cell 19 If necessary during the delay span Arming can be aborted by using the Keychain Magnet or an optional external wired button switch After the delay countdown span concludes the Security Alarm Sensor will exit ArmDelay mode and enter Armed On Guard mode In order to verify Armed On Guard mode while in On Guard mode pass the Keychain magnet in close proximity to the Security Alarm Sensor location or press the optional external wired button switch if installed and the Security Sensor Alarm will flash briefly and emit a beep refer to Chart 3 In
15. iag 7 3 Disable the SIM card PIN code feature by using a GSM Telephone see telephone operating manual 4 a Re locate the Security Alarm Sensor to a spot with good access to a GSM Network signal b Change the mobile network provider 21 4 CONTACT INFORMATION ALPHA ARSENAL ALPHA ARSENAL LLC 104 20 Queens Blvd Ste 1B Forest Hills NY 11375 US T F 1 718 440 3281 1 718 355 9281 Skype alpha arsenal E mail info alpha safe com support alpha safe com Website www alpha safe com 22 ess LPHA ARSENAL ALPHA ARSENAL ALPHA ARSENAL ALPHA ARSENAL ALPHA ARSENAL ALPHA AR BEST SOLUTION FOR SAFETY OF YOUR HOME k iOS or Android
16. installs with 2 screws using the mounting holes found on the base or by using double sided scotch tape refer to diagrams 2 4 item 2 7 1 6 Keychain Magnet Design The keychain magnet is a permanent constant magnet dimensions 18x10x1 5 mm Diagram 4a Exposed view of the Keychain Magnet 1 7 Functional and operational basis of the Security Alarm Sensor 1 7 1 Functional concept of the Security Alarm Sensor Device In On Guard mode when the door opens triggered violation the magnet ceases to effect the magnetic detection sensor or the external wired relay sensor the Security Alarm Sensor Device generates Active Delay amp Alarm signals which in turn execute notification 1 7 2 Primary functions of the Security Alarm Sensor The Security Alarm Sensor performs the following functions detects unauthorized penetration breach of the protected door s transmits an alarm SMS and or a call to the telephone numbers registered on the Security Alarm Sensor SIM card transmits an armed disarmed SMS to the primary notification number optional automatically resets to On Guard mode an SMS re auto reset is not sent automatically requests remaining Security Alarm Sensor SIM card balance and transmits an SMS to the primary notification telephone number automatically detects remaining balance inquiry telephone number 1 7 3 Primary functions of the Keychain Magnet The Keychain Magnet performs t
17. is generated only when any one of the external sensors are triggered POLUS GSM Detection sensor switch EAR Sensor Sensor Sensor Diag 6b Link up diagram for External Sensors Switches Value 1 cell 37 Option 2 The Security Alarm Sensor is installed with magnet i e it operates as a magnetic detection sensor The Alarm signal is generated only when two of the sensors are triggered an external sensor with a mandatory Security Alarm Detection Sensor 12 Installation option E g both the Security Alarm Sensor and external sensor are installed on the same door The door becomes ajar no Alarm is generated only one sensor triggered When the door opens completely an Alarm is generated when both sensors are triggered Link up diagram see diag 6c POLUS GSM Detection sensor switch Diag 6c 2 SET UP PROCEDURE 2 1 Preparation of the Alarm Device for Operation After opening the package visually inspect the Security Alarm Sensor Device for any physical defects and make sure all parts are included Check and make sure there is a sufficient SIM card balance 2 2 Configuring the Alarm Device At initial power up the Security Alarm Sensor records on to the SIM card the following parameters and values in accordance with Chart 4 Chart 4 Security Alarm Sensor Settings Cell Cell label Default Value Description Available Values Position
18. lay google com search Express GSM or GSM Panel The created configuration will be sent to the Security Alarm Sensor SIM card Method 2 1 Using the primary notification telephone create an SMS message using values in accordance with Chart 4 For example in order to change the notification method it is necessary to send an SMS message containing the following text 18 0 where 18 indicates the cell number and O indicates the selected parameter value Note Characters are entered without quote marks and spaces 18 2 7 2 7 1 In order to change several parameters it is necessary to list the parameters separating them with a comma For example 2 1XxXxXxXxXxxXXxx 16 0 18 0 19 60 etc Note Characters are entered without quote marks and spaces Access Programming mode in the Security Alarm Sensor item 2 3 Send a prepared SMS message to the Security Alarm Sensor telephone SIM card number Wait to receive an SMS notification confirming selected parameter values Method 3 It is possible to change and configure the parameter values directly with the aid of a GSM mobile telephone In order to accomplish this install the Security Alarm Sensor SIM card into a GSM mobile telephone To access the necessary parameter open the telephone book select the cell to be altered and make the necessary changes in accordance with Chart 4 For example in order to change the primary notification tele
19. llation description see diag 9 Wait to receive an SMS notification containing the text Armed default setting possible to turn off Wait for 2 3 minutes then move the Magnet away from the Security Alarm Sensor for a distance greater than 8mm see Chart 2 the light diode indicator will glow red while registering on the GSM network then blink green as it enters Active AutoArm Delay mode After 40 forty seconds default setting the light diode indicator will blink red showing that the Security Alarm Sensor has entered the Alarm mode Wait to receive an SMS notification containing the text Alarm and a telephone call from the Security Alarm Sensor Place a call to the Security Alarm Sensor telephone number Wait for an SMS notification containing the text Disarmed by a call from 1 the Security Alarm Sensor has now entered Disarmed mode and light audio indicators are turned off 2 6 Changing the Parameter Value Settings Value parameter settings are installed during the 1 first power up and later be changed The parameter values can be changed using the following methods Method 1 The Security Alarm Sensor settings can be configured by using the Online Service located at service alpha safe com by utilizing the Express GSM Configurator for Android or iOS or by using the application for central monitoring GSM Panel available for download from p
20. m Sensor and External Sensor at the intended locations Attention In the Security Alarm Sensor settings cell 37 value 1 or 2 must be selected Verify the correct installation of the external sensor as described in item 2 5 and check the proper operation of each installed Alarm Sensor 3 TROUBLESHOOTING Chart 5 Troubleshooting Guide Description of Symptom Possible Cause Solution No Audio beeps or GSM light diode flashes in the Alarm Sensor after the Battery is installed 1 Battery improperly installed 2 Battery is discharged 1 Remove the battery amp re install properly using proper polarity 2 Install a new fresh Battery CR123A 3v When arming using the Keychain magnet there Is no response from the Alarm Sensor No audio Beeps during the arming Delay span see chart 3 The keychain magnet is more than 10mm away from the Alarm Sensor Reduce the distance between the keychain magnet and Alarm Sensor After powering up the Alarm Sensor installing The battery the GSM Light diode flashes rapidly amp does not flash once 1 Every 4 four seconds as Required SIM card is not Logging on to the network 1 SIM card is not installed 2 SIM card is incorrectly installed 3 SIM card is locked with a PIN code 4 GSM network is inaccessible 1 Verify the presence of a SIM card 2 Remove SIM card amp re install as shown in d
21. phone number in the telephone book select 1SMS then select change erase the old number and record the new primary notification telephone number etc Note Some mobile telephones do not support this function In addition to the change parameter methods listed above adding deleting notification telephone numbers can also be accomplished via a telephone call from the primary notification telephone number to the Security Alarm Sensor while in Programming mode see item 2 4 After calling from the primary notification telephone number all telephone numbers contained in the SIM card memory are erased and it will be necessary to add all required telephone numbers all over again Security Alarm Sensor Installation The Security Alarm Sensor should be installed at a location that will be shielded from atmospheric elements physical damage and access by unauthorized strangers and at the same time have access to a reliable GSM signal The Security Alarm Sensor should be located away from high power cables Installing the Security Alarm Sensor without External Sensors The body of the Security Alarm Sensor and Magnet must be installed parallel to each other with each of the guide marks facing each other 19 and maintaining proper clearance between them see diag 9 Chart 2 The Security Alarm Sensor should be mounted on a non movable surface for example on a door jamb and the Magnet on a movable surface for exam
22. ple directly on a door Location of the Arming Sensor Security Alarm Sensor k Guide Marks 68 mm 31mm magnet Break Off Openings For Running Wire Diag 9 Installation Diagram with Connection Specifications In order to install the Security Alarm Sensor execute the following steps consecutively 1 Mark out and measure the selected location for installation taking into account and allowing for openings on the body of the Security Alarm Sensor and Magnet 2 Install the Security Alarm Sensor by removing the cover and the circuit board from the base Attach the base using two screws then snap in the circuit board followed by the cover If required hook up an external switch button see diag 10 external switch button Diag 10 Diagram for Hooking Up an Optional External Switch Button 3 Install the Magnet by removing the cover and fastening the base down by using two screws then re attach the cover to the base Double sided tape can be used for attaching to a prepared surface 20 Inspect that the installation was correctly performed and verify operational integrity as described in item 2 5 by arming the device and opening the door If an external switch button was installed test arming and disarming the Security Alarm Sensor by briefly activating the optional external switch button 2 7 2 Installing the Security Alarm Sensor with External Sensors Install the Security Alar
23. rated more than 8mm Distance at which a Normal signal is restored less than 6mm Operating distance between keychain Magnet and Alarm Sensor Device not to exceed 10mm GSM Module Operating Standards GSM 800 900 1800 1900 Quantity of telephones to be notified 6 six Time lapse for notification 20 40 seconds Battery type 1 x CR123A 3v Uninterrupted operating life span using one battery at a temperature of 25C up to 12 months Temperature operating range from 10 to 50 C Enclosure durability level IP40 Relative operating humidity 35c without condensation not to exceed 93 Alarm Sensor Device size amp dimensions do not exceed 109x32x27 5 mm Magnet size amp dimensions do not exceed 56 5x18x15 7 mm Alarm Sensor Device w battery Magnet weight do not exceed 60 g 10g Footnote the Security Alarm Sensor will operate below 25c but battery operating life span and quantity of SMS s sent will be reduced 1 4 Security Alarm Sensor Design The Alarm Sensor device unit consists of a cover body with a light diode indicator and a base diagrams 1 amp 2 Inside the cover body mounted on the base is the controller circuit board to which the GSM module is attached diagram 3 The circuit board and cover body attach to the base unit using clips The cover body and base unit are made of ABS plastic Light diod
24. s accomplished with the assistance of a keychain magnet or with an optional external button switch Disarming is accomplished by placing a call from any one of the mobile telephones registered to the Security Alarm Sensor SIM card 10 In order to Arm the unit briefly 1 2 sec bring the keychain magnet up to where the Security Alarm Sensor magnet is located see Diag 9 amp 3 or briefly 1 2 sec press the optional external button switch if installed For the duration of 30 seconds default ArmDelay setting the Security Alarm Sensor will emit audio chirps During this duration of time it is necessary to close the door At the conclusion of the time delay the Security Alarm Sensor will enter Armed mode During the span of the time delay arming can be cancelled with the assistance of the keychain magnet briefly bring the keychain magnet up to where the Security Alarm Sensor magnet is located or simply press the optional external button switch In order to Disarm the unit place a call from any one of the mobile telephones registered to the Security Alarm Sensor SIM card Attention Disarming is only possible in Active AutoArm Delay Alarm amp Standby NotDelay modes i e in the absence of a triggered Alarm in order to Disarm the unit it is necessary to open the door In the event that the ArmDisarm cell see Chart 4 cell 16 on the Security Alarm Sensor SIM card contains and
Download Pdf Manuals
Related Search