BUILT-IN BEER DISPENSER SBC635MBI Series
Contents
1. If the leakage of a combustible gas is detected turn off the gas valve and open the doors and windows To reduce the risk of fire caused by a spark do not pull out the plug of the beer dispenser or of any other electrical device SAFETY PRECAUTIONS REGARDING CO CARBON DIOXIDE GAS Always connect the CO cylinder to a regulator Failure to do so may cause an explosion resulting in possible injury or death when the cylinder valve is opened Never connect the COs cylinder directly to the product container Always keep CO cylinders away from heat Store extra cylinders in a cool place preferably below 70 F Securely fasten cylinders with a chain in an upright position when storing Never drop or throw a CO cylinder Always check the D O T Department of Transportation test date on the cylinder neck before installation If it has been more than 5 years do not use Return the cylinder to your gas supplier Never connect a product container unless there are at least two safety devices in the pressure system one on the COs regulator and the other on the product container or in the pressurized gas line The recommended pressure for the CO2 system is 8 10 Ibs SAVE THESE INSTRUCTIONS Notes on Energy Consumption This product is designed for commercial use and is UL approved to standard 471 commercial refrigeration It features an upgraded cooling system over units designed for household use At national average electric rates it wi2. codes gt gt gt DO NOT USE AN EXTENSION CORD lt lt lt Required nominal voltage and frequency are indicated on the rating plate The connection to the power supply and grounding has to be made according to current standards and regulations The appliance resists temporary voltage fluctuations with a tolerance of 10 Once connected allow the appliance to operate empty for two to three hours before putting a beer keg inside Reversing the Door Swing select units onl Figure 1 Default position Figure 2 After door reversal 1 Upper hinge cover 6 Screws 2 Screws 7 Hole cover 3 Upper hinge 8 Cabinet 4 Door 9 Pin cap 5 Lower door hinge Depending on your door finish the beer dispenser can be opened from either the right side or the left By default the door hinge is on the right side If you prefer it on the left please follow these instructions providing your model number does not end in SSTB SSHV or DPL Note 1 2 3 All of the parts that are removed must be kept for the reinstallation of the door Remove the three screws 6 holding lower door hinge 5 Keep hinge for later use Remove the door from the upper hinge 3 and keep the padded surface upward to prevent scratching Remove the upper hinge cover 1 remove the two screws 2 remove the upper hinge 3 and keep it for later use Remove the hole cover 7 and transfer it to the same location on the opposite side Insert the lowe
3. service matters to qualified technical personnel 10 Keep packing materials away from children as they could become a choking hazard 11 Do not spray or flush the beer dispenser with water and avoid keeping it in a damp place since this could damage the electrical insulation DANGER Risk of child entrapment Child entrapment and suffocation are not problems of the past Junked or abandoned appliances are still dangerous even if they will just sit at the curb for a few days Before discarding your old appliance e Take off the door e Leave the shelves in place so that children may not easily climb inside SAFETY PRECAUTIONS REGARDING ELECTRICAL MATTERS Do not pull on the power cord when unplugging the machine Grasp the plug firmly and pull it straight out of the socket Do not pull the plug with wet hands Keep the power cord at the back of the appliance to avoid tripping accidents or damage to the cord If the power cord is damaged or frayed it must be replaced by a qualified service professional Use only a standard three hole grounded power socket rated above 10A The socket should not be shared with other appliances Be sure the plug fits firmly into the socket and that the socket is grounded The use of an extension cord is NOT recommended 7 The beer dispenser requires an AC power supply of 110 120V 60Hz and pulls a current of over 10A The fuse or circuit breaker should be rated at 15A 8
4. too often especially when the weather is hot and humid Once you open the door try to close it as soon as possible If possible disconnect the power before changing a keg of beer Keep the unit out of direct sunlight Periodically check that the beer dispenser seals well and that none of the contents prevent the door from closing PLACEMENT AND INSTALLATION Choosing the Right Place To ensure that your beer dispenser works at the maximum efficiency it was designed for install it in a location where there are proper air circulation and electrical connections Choose a location where the beer dispenser will be away from any heat sources and will not be exposed to direct sunlight Remove all packing materials before using the beer dispenser Place the machine on a smooth flat and sturdy surface Installation Your appliance is designed for built in use and features fan assisted compressor cooling For optimum operation however we recommend providing an air gap of 2 between the rear of the unit and the wall or counter surface This will enhance cooling and reduce energy waste Also leave at least 1 8 on both sides and 1 16 at the top Be sure that airflow under the appliance is not blocked Connecting to Power Supply Connect this appliance to a 3 prong power supply socket which has a ground terminal lf you only have a two prong outlet have it replaced by a qualified technician with an outlet that meets the local
5. NTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE WARNING This product may contain chemicals known to the state of California to cause cancer or birth defects or other reproductive harm For more information visit Www summitappliance com prop65 Chemicals known by the manufacturer to be present in this product in concentrations higher than threshold limits NONE FELIX STORCH INC 770 Garrison Avenue Bronx NY 10474 Phone 718 893 3900 For parts and accessory ordering Fax 844 478 8799 troubleshooting and helpful hints visit www summitappliance com www summitapplianceparts com Printed in USA 19
6. age the rear wall the condenser unit or the tubes or any part of the refrigeration system inside the appliance This beer dispenser is 100 CFC free but the coolant is under pressure and puncturing the sealed system could be dangerous The coolant used in the sealed system is non toxic Many older appliances may contain refrigerants that are harmful to the environment and should be recycled by a lawfully licensed company 15 DRAFT BEER TROUBLESHOOTING Problem Cause Correction Beer is cloudy The beer in the glass appears hazy and not clear Excessively low temperatures may cause hazy or cloudy beer particularly when the beer lies in the cold coil for long oeriods of time Glasses may not have been cleaned properly Improper drawing of beer into glass Not enough pressure Drain a few ounces before drinking Raise the temperature setting of the unit Do not wash beer glasses together with glasses that have contained milk or any other fatty substance An excessive amount of germicide build up may also leave a fatty film which will cause beer to go flat It is preferable to steam and sterilize glasses where health laws permit Wash glasses thoroughly with a good detergent to remove all fatty substances e g lipstick Do not use soap Do not wipe the glasses dry Permit glasses to air dry by placing them on a wire rack or corrugated metal sheet Rinse the glasses in fresh cold water ju
7. e keg When replacing the CO gas cylinder remember to turn off the main switch of the COs gas cylinder and the safety switch on the COs regulator valve Afterwards use a wrench to loosen the hexagonal nut port connecting the COs regulator valve with the CO tank Then using a wrench remove the fixed bolt of the CO tank to take out the CO tank During the installation process be sure that all parts are connected tightly and that there are no gas leaks When connecting the hose to the connection port you can dip the ends into warm water to make the connection easier If the high pressure compressed gas in the CO tank is not handled properly it could be dangerous a Make a note of the D O T testing date on the cylinder neck before installation If it is more than 5 years old don t use the product Return it to the gas supplier b Keep gas cylinder away from heat sources Unused cylinders should be placed upright in a cool ventilated place preferably at 70 F 10 OPERATION Control Panel The control panel is located just above the door and looks like this Cooler g Warmer CE9 Frc GQ Deap Chil 7 l i DOWN Lowers UP Raises Display module Fahrenheit Celsius Rapid temperature temperature switching cooling Setting the Temperature Adjust the DOWN or UP button on the control panel until the display module shows the desired temperature The display module shows the set temperature and the te
8. ents become wet Out of Service lf the machine will be out of service for more than three weeks unplug it and clean and dry it thoroughly Allow the door to remain open slightly to prevent the buildup of mold and odors Transporting the Unit Firmly fix any loose items inside the beer dispenser with tape Tape the door shut so it will not open during transportation Loosen the two foot brakes before moving the unit Specifications of Beer Kegs Keg sizes that can be used in your beer dispenser 1 2 barrel 59 liters 15 5 gals 1 984 oz 164 12 0z Glass 1 4 barrel 30 liters 7 8 gals 82 12 0z Glass 1 6 barrel 20 liters 5 2 gals 55 12 0z Glass 1 8 barrel 15 liters 4 0 gals 41 12 0z Glass Note Our beer dispenser accepts almost all brand name 1 2 kegs However Coors kegs do not fit in our unit 14 DISPOSING OF A WORN OUT APPLIANCE When your appliance finally wears out dispose of it Before you dispose of an old appliance Take the door or doors off but leave any shelves or drawers in place so that children cannot easily climb inside The refrigerating system of the appliance is filled with refrigerant and insulating substances that should be recycled separately Either have a licensed appliance repair company or dealer remove the appliance or call your local recycling office for the appropriate disposal information For the sake of environmental protection when moving the appliance be careful not to dam
9. fects Plastic parts shelves and cabinets are warranted to be manufactured to commercially acceptable standards and are not covered from damage during handling or breakage 5 YEAR COMPRESSOR WARRANTY 1 The compressor is covered for 5 years 2 Replacement does not include labor ITEMS WARRANTOR WILL NOT PAY FOR Service calls to correct the installation of your appliance to instruct you how to use your appliance to replace or repair fuses or to correct wiring or plumbing Service calls to repair or replace appliance light bulbs or broken shelves Consumable parts such as filters are excluded from warranty coverage Damage resulting from accident alteration misuse abuse fire flood acts of God improper installation installation not in accordance with electrical or plumbing codes or use of products not approved by warrantor Replacement parts or repair labor costs for units operated outside the United States Repairs to parts or systems resulting from unauthorized modifications made to the appliance Expenses for travel and transportation for product service in remote locations The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN IMPLIED WARRA
10. he machine is in use the noise is caused by the refrigerant flowing in the cooling pipes and running through he compressor This is a normal phenomenon e The beer dispenser has no heating function When the temperature is set higher than the ambient temperature the machine will not run Dispensing Beer Follow these steps to dispense beer 1 Make sure the beer dispenser is plugged in properly to a 120V 60Hz 15 amp grounded AC outlet 2 Place the drip tray under the beer tap 3 Open the beer faucet by pulling the tap towards you quickly and completely to dispense the beer 4 Increase the pressure if the beer runs too slowly At the correct pressure and temperature a 10 0z glass should be filled in 4 seconds 12 5 Hold the glass steady at a 45 angle When it is 2 8 full start straightening the glass Proper foam should be a tight creamy head and the collar on an average glass should be 3 4 to 1 high Note It is normal to see condensation forming on the tap It is caused by the difference in temperature between the cold beer and the inner surfaces of the tap when beer is flowing through the line Understanding Beer Temperature The recommended temperature for serving chilled beer is between 38 and 43 F To maintain this temperature in average room conditions of 70 F set the thermostat accordingly Notes During the summertime when temperatures are warmer we recommend that you adjust the control to a cooler se
11. linder Bracket and retainer _ mixed ball valve and the round outlet of co nk the COs regulator valve Lock these connections firmly with the two clamps on Figure 8 the red CO tube See Figure 7 c Using the wrench tighten the COs regulator table valve with the hex nut port to the gas outlet of the CO tank See Figure 8 d Place the COz tank and COz regulator valve component into the cabinet and fix the COs tank with tank bracket and bolt See Figure 8 4 Install the beer keg Place the beer keg into the cabinet and firmly connect the keg s opening to the connection port of the mixed ball valve See Figure 10 Note To place a keg into the cabinet use the keg handle to move the keg to the front of the open beer dispenser then carefully tip the keg so that the raised bottom edge contacts the edge of the cabinet Finally lift the keg handle to raise the keg to the level of the floor of the cabinet and push the keg into place 5 Install tap handle and beer tap screw the tap handle clockwise into the beer tap to make a firm connection Then connect the tap to the beer tower components and tighten with a wrench See Figure 9 6 Install upper cover guardrail and drip tray Set the upper cover guardrail and drip tray on top of the beer dispenser See Figure 10 Notes When replacing the beer keg first turn off the safety switch on the COz regulator valve and remove the mixed ball valve to take out th
12. ll the two universal wheel washers at the front of the cabinet base and then install two universal wheels without foot brakes Next install the two universal wheels with foot brakes at the back of the cabinet base Once installed these rear 8 wheels will keep the unit from moving if you step on the foot brakes See Figure 2 Figure 2 2 Install the beer tower assembly and the mixed ball valve a Plug the beer tower assembly into the top cover of the beer dispenser 3 0 tower This does not require a tower buckle Put beer tower directly over the hole at the top of the beer dispensers upper surface Fix the beer tower assem bly with screws directly on the upper sur face of the beer dispenser See Fig 3 Figure 3 2 5 tower This requires the tower buckle Place the beer tower at the hole in the upper surface of the beer dispenser at an inclination of 60 and rotate 60 clockwise along the card slot Be sure the tap is facing toward the front of the machine Attach the beer tower with washers See Figure 4 b Take out the accessories of the mixed ball valve Attach the transparent hose to the beer outlet of the mixed ball valve See Figure 5 Figure 5 Figure 6 Figure T 3 Install CO2 gas cylinder and COs regulator valve a Fix the two COs hose clamps on the red CO tube See Figure 6 ae aaa Ja table b Connect the ends of the red COs tube ee e oak respectively to the COz intake port of the cy
13. ll use less than 1 per month more in electricity than household units Tips to save energy and maintain optimum performance When positioning this unit If used freestanding allow 4 inches of clearance on top at the sides and in the rear for sufficient airflow If unit is built in allow 2 of air soace between the rear of the unit and the wall also leave at least 1 8 on both sides and 1 16 at the top Be sure that airflow under the appliance is not blocked LOCATION OF PARTS Beer tower assembly Upper cover guardrail Collar Drip tray Top cover l Display and control anel Cabinet p Evaporator CO regulator valve CO gas cylinder Ball valve CO tank supporter Beer keg Control board device Door Compressor chamber cover Bottom pad Leveling leg BEFORE USING FOR THE FIRST TIME The SBC635MBI is designed for dispensing beer only and is not recommended for storing perishable foods such as meats or dairy products Before connecting the appliance to the power supply leave it standing for 2 to 3 hours This allows the refrigerant to drain back into the compressor and reduces the risk of malfunctions in the cooling system caused by shipping Clean the appliance thoroughly especially the interior See Maintenance of the Beer Dispenser Proper grounding must be ensured to reduce the risk of shock and fire Do not cut or remove the grounding plug TIPS FOR SAVING ENERGY Try not to open the door
14. mperature controlled range varies from 32 to 50 F 0 to 10 C The display module shows 5 C at the initial power up Each press of the DOWN or UP button decreases or increases the temperature displayed by 1 C 1 F The optimal temperature for the storage and distribution of beer is 34 38 F 1 1 to 3 3 C Switching between Celsius and Fahrenheit You can switch between a Celsius and Fahrenheit temperature display by pressing the F C button When the displayed temperature Is in Celsius the C symbol will be illuminated with a Fahrenheit display F will be illuminated Rapid Cooling Function Press the Deep Chill button to enter the Rapid Cooling state The rapid cooling icon on the display module will light and the temperature display will read OO After entering the Rapid Cooling mode the appliance will work continuously for 24 hours and the icon will remain lit After that time the icon will turn off and the appliance will return to its former state You can cancel the Rapid Cooling mode any time during the 24 hour period by simply pressing the Deep Chill button again Note The Rapid Cooling function is normally used only for cooling the first keg of beer in the appliance when that keg Is to be used as soon as possible To prevent over cooling the beer do not use Rapid Cooling for succeeding kegs 11 Automatic Defrosting There is usually no need to defrost the beer dispenser becau
15. nches from left to midpoint 12 inches from right to mid point 12 11 16 inches from front to mid point Drill a round hole Place a drill bit on the mid point and make a round hole with a diameter of 1 7 Installation See Installation instructions in this manual Installation of Accessories Diagram of overall structure fi Beer tower assembly Upper cover guardrail Collar eka Top cover Display and control Cabinet device ee Transparent hose Beer tube Soft red CO2 tube Mixed ball valve Beer keg handle CO can supporter and bolt Door CO gas cylinder oe Beer keg Beer can bottom pad Leveling legs or Universal wheels Installation components Tap handle Main awitch of CO gas cylinder Beer outlet Draft beer tap Outlet of CO gas cylinder ALEE EPEE Tower body r i Contral hande EC CO inlet Hex nuts port Tower buckle Interface connected Regulating knob Transparent hose Beer tube to beer barrels Safety awitch Round alr outlet Beer tower assembly Mixed ball valve CO gas cylinder CO regulator valve Wrench wT Y oOo 8 fp Universal wheels Universalwheelg Universal wheel CO hose clamp COz2 tank bracket and bolt with fool brake without ihe footbrake washer Installation steps 1 Install universal wheels optional Lock braking guidelines for universal wheels or with foot brakes See Figure 1 lf you would like to make the beer dispenser into a mobile unit insta
16. r door hinge 5 into the left side fixing the hinge into place by tightening all the screws 6 Remove the pin cap 9 from the left side of the upper door frame and then transfer it to the same location on the opposite side Set the door on the lower door hinge 5 keep the door level then fix the upper hinge 3 to the body 8 by the screws 2 Put on the upper hinge cover 1 Installing the Beer Dispenser as a Built In Unit This beer dispenser is designed to be built in under your counter Simply follow the steps below for a quick and easy installation NOTE Not all models have built in capability Only models with letters BI are built in compatible We do not advise that other models be built in under your counter 33 9 16 MIN 24MIN The dimensions of your unit are Make sure the available space Height 33127 adjustable to 34 is adequate Allow at least 1 8 with leveling legs clearance on both sides 2 at Ath DA the rear and 1 16 at the top wales Be sure that airflow under the Depth 25 appliance is not blocked Allow 1 extra for door to swing completely open 11 for stainless steel doors Instructions for Building In Find the mid point From left to right the width is about 2414 From back to front the dimension is about 25 Therefore the mid point is located wherever these coordinates cross each other Use a pencil or marker to note this spot Note 12 i
17. re drinking 17 GENERAL TROUBLESHOOTING lf there is a problem with the beer dispenser itself see if you can find it listed in the chart below You may be able to save yourself the cost of a service visit Possible Cause The beer dispenser doesn t Power supply not firmly connected work Supplied voltage is too low Tripped circuit breaker or blown fuse The machine switches on Indoor temperature is higher than usual and off frequently Machine door is opened frequently Door is not completely closed Temperature control is not set correctly Door cannot be closed Beer keg not properly placed properly Beer dispenser is not level Door was reversed and re installed incorrectly Metal plate or beer kegs are out of place Rushing noise may be the sound of refrigerant flow which is normal As each cycle ends the gurgle of refrigerant flow may be heard Contraction and expansion of inner wall may cause pops and crackles 18 LIMITED WARRANTY ONE YEAR LIMITED WARRANTY Within the 48 contiguous United States for one year from the date of purchase when this appliance is operated and maintained according to instructions attached to or furnished with the product warrantor will pay for factory specified parts and repair labor to correct defects in materials or workmanship Service must be provided by a designated service company Outside the 48 states all parts are warranted for one year from manufacturing de
18. se the ice deposited on the inner back wall is automatically defrosted Ice deposits on the inner back wall during compressor operation Later on when the compressor is not operating the ice defrosts and water drains through the outlet in the inner back wall into the drain pan situated above the compressor where it evaporates If you see water building up in the rear of the unit check that the drain trough is not clogged Use a pipe cleaner or a piece of flexible wire During extremely hot and humid weather some ice may build up If necessary remove contents of the beer dispenser unplug the unit and allow defrosting A hair dryer may facilitate the process Error Prompts When the following prompts appear in the display module there is a failure in the appliance Although one of the fault conditions occurs the beer dispenser may still work However you should contact our Service Department as soon as possible to obtain advice on handling the situation Temperature sensor Defrosting sensor Ambient failure in the failure in the refrigerator temperature refrigerated zone compartment sensor fault Note When two or more sensors fail simultaneously all fault codes will display alternately on the display module If the ambient temperature and defrost sensors fail any key may be pressed The temperature is adjustable The fault display will be restored after 15 seconds Normal Functioning e lf there is a sound of rushing water when t
19. st before serving beer It is best to serve beer in a wet glass Open the faucet quickly and completely proper foam should be a tight creamy head The collar on the average glass should be 3 4 to 1 high Beer drawn without a head has the appearance of being flat Increase the pressure if beer runs too slowly The correct flow should fill a 10 oz glass in 4 seconds approx 8 oz of liquid Check the pressure source to determine whether there are obstructions in the air line Replace a sluggish air source or the CO regulator and gauge The tank pressure must always be higher than the pressure used on the keg Always apply oressure to the keg before drawing beer 16 Beer has off taste Often bitter and bite y sometimes completely lacking flavor and zest It may also have an oily or foul odor which may carry an unpleasant taste Condensation is forming on the tap Improper cleaning of the tap Contaminated air line It is normal to see conden sation forming on the tap It is caused by a difference in temperature between the cold beer and the surfaces of the tap when beer is flowing through the line Beer that is left in the tap is not cooled by the beer dispenser Brush and clean the tap properly It should be scoured using a detergent then rinsed clean Beer tube should be examined If contaminated it should be replaced After a period of non use a few ounces should be drained befo
20. suMMIT BUILT IN BEER DISPENSER SBC635MBI Series Use and Care Guide BEFORE USE PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Keep proof of original sales date such as your sales slip with this manual to establish the warranty period Write the Serial Number here You ll find it on a plate located either on the back of the appliance or on an interior wall Felix Storch Inc 770 Garrison Avenue Bronx NY 10474 www summitappliance com IMPORTANT SAFEGUARDS WARNING To reduce the risk of fire electric shock or injury when using this appliance follow these basic precautions 1 The appliance must be correctly connected to the power supply Immediately replace worn power cords loose plugs and faulty power outlets Do not operate your appliance in the presence of explosive fumes Disconnect the appliance from the power supply before cleaning or repairing it Only O B amp B W PO 9 Read all instructions before using the appliance a qualified technician should repair it Never stand on top of or inside this appliance or swing on the door Avoid putting weight on top of the appliance To reduce likelihood of injury do not let children play with this appliance Do not operate the valve control unless the cylinder is completely installed and connected Do not attempt to repair or replace any part unless this is recommended in this Use and Care Guide Leave other
21. tting Selecting and maintaining the proper temperature inside the refrigerator cabinet is necessary for maintaining the flavor and freshness of beer Excessively cold or warm temperatures inside the refrigerator cabinet may cause a loss of flavor The best temperature for storing a keg is approximately 38 F Sour beer is produced as a result of secondary fermentation above 45 F Beer Serving Tips The following tips will help you serve the perfect beer To serve beer from the tap similar to the way it left the vat check the following e Cleanliness see Maintenance of the Beer Dispenser e Temperature see Setting the Temperature and Understanding Beer Temperature e Pressure The recommended pressure for the COs system is 8 10 Ibs e Use only COs gas 13 MAINTENANCE OF THE BEER DISPENSER Cleaning To optimize cooling and to save energy at the same time dust the back of the beer dispenser periodically The interior should be cleaned regularly Use a soft towel or sponge that has been dampened in a solution of mild detergent Rinse with clean water and dry with a cloth Leave the door open for a while to allow the unit to dry thoroughly before turning the power back on Do not use a hard brush steel wool wire brush or abrasives such as toothpaste or organic solvents like alcohol or acetone to clean the beer dispenser When cleaning or rinsing the unit be careful not to let the control panel or any electrical compon
Download Pdf Manuals
Related Search