Home
Controlling the PCR-LE - Kikusui Electronics Corp.
Contents
1. Setting AC DC AC DC AC U V Yes AC VIV Yes DC V Yes Interval s Yes Yes Trans AC Yes Trans DC Yes Trig IN Yes Yes Trig OUT Yes Yes Output Yes Yes Freguency Yes Trans f Yes WB No Yes S Phase Yes Start deg Yes E Phase Yes End deg Yes Pri phase Yes U offset Yes U offset deg Yes U offs ramp Yes UV phase Yes UV deg Yes UV ramp Yes Stat OUT Yes Yes Outp Imp Yes Yes Outp Imp Yes Yes Jump Loop Yes Yes Jump Stop Yes Yes Loop Count Yes Yes 1 Depending on the time unit that you specified in sequence creation mode s ms min or h the in terval in the worksheet is set to Interval s Interval ms Interval min or Interval h 2 This setting is available only when the Jump Loop is set up check box under An option setup of a step is selected in the Sequence Creation Mode dialog box SD011 PCR LE Ver 5 5x Creating Seguence Steps E Settings for three phase Output voltage mode Setting AC DC AC DC AC U V Yes AC VIV Yes AC W V Yes Interval s Yes Trans AC Yes Trig IN Yes Trig OUT Yes Outpu
2. Setting Description Value AC V Set the AC voltage that you want A value between 0 0 V and 305 0 V to generate DC V Set the DC voltage that you want A value between 431 0 V to 431 0 V to generate Trans AC Set the AC voltage change Step Ramp Trans DC Set the DC voltage change Step Ramp 1 If the wiring method is single phase three wire or three phase specify the phase voltage Phase voltage settings appear as AC U V AC V V or AC W V 2 You can set the voltage as low as 0 0 V but even if you do the actual output voltage will always be in the range of 0 1 V to 0 6 V The minimum value varies depending on the output voltage range and temperature 3 If the wiring method is single phase three wire specify the phase voltage The value is assigned to the U phase The V phase is automatically set to the same amplitude as the U phase but with opposite polarity 4 If the output voltage mode is set to AC DC voltage to set the DC voltage the following two conditions must be met e The specified AC and DC voltages are within the voltage limit range specified on the PCR LE e The peak value of the AC DC waveform is within the range of 431 V to 431 V for H range and 215 5 V to 215 5 V for L range 5 In the PCR LE user s manual step is denoted as ramp off and ramp as ramp on 6 To change the voltage linearly over a specified time select Ramp To change the value as a step
3. 1 If you set the wiring method to single phase three wire or three phase specify a phase voltage 2 The OCP internal semiconductor protection protection function protects the internal semi conductors of the PCR LE If you set the length of time that must elapse after the OCP is activated before an alarm is gen erated detection time of OCP activation an alarm will not be generated until the specified length of time elapses even if the internal semiconductor protection is activated This setting can be used to prevent the alarm from being generated due to temporary overcurrent such as inrush current Normally if the PCR LE is used in a manner that conforms to its specifications the internal semi conductor protection is not activated However if a temporary overcurrent such as an inrush current occurs the internal semiconductor protection function will be activated If the inter nal semiconductor protection function is activated the output voltage waveform will be dis torted E Current limit Current limiting features are available on the PCR LE For the setup procedure see Setting the PCR LE current limits on page 45 Setting Description Current limit Set the output current s upper limit peak current limit Set the positive peak current limit peak current limit Set the negative peak current limit Trip Set whether the output is turned off when the current exceeds the current li
4. sccccccssssscsccccsssscees 54 Other Seng S sssiuvisaenv savasevesa snnvin sguses ra tiv isate 56 Setting the mouse resolution used to set steps 56 00000 Always using the voltage transition mode when using the mouse to set SEEPS ninsnsenenenonennenenenennenenenenennet 56 Setting the maximum data SiZE snersenenennenenesn 57 Changing the graph properties rwresnnsnerenses 57 Changing the file format of sequence data 60 Changing the file format of monitored data 60 Changing the window design wnnesnensnenenses 60 Changing the folder that arbitrary waveforms are saved Amata ia E EE a a 61 Changing the display format of the Graph and Work sheet UMN aa titaliis eua eee eee 61 Creating and Transferring Arbitrary Waveforms 62 Creating a new arbitrary waveform and transferring itto the waveform bank munsensenenneneeneneenennennenaenenennene 62 Editing an existing arbitrary waveform and transferring it to the waveform bank unnnsenseneenennenensenenne 68 Transferring an existing arbitrary waveform to the waveform DaNK ccscssssessssscsecssssssscscssssesssesesessecsecsecssensensenees 68 Creating arbitrary waveform data using data from an oscilloscope or other instrument 69 Displaying the Waveform View eeereeneeee 71 Controlling the PCR LE Directl
5. n ennu Hmmm 555555 ooo ooo ooo 000000 ooo o Control Control Write PCR LE For details on the list of waveform banks see Displaying the Waveform View on page 71 13 14 MII wW p Setting the Seguence Creation Mode Seguences are groups of executable units called steps In Wavy first set conditions that apply to all steps in the Seguence Creation Mode dialog box and then create the individual steps You can create steps in the Graph window and Worksheet window The setup settings that appear in the Worksheet window vary depending on the seguence creation mode settings You cannot change the seguence creation mode while a step is being created For details on step settings and how to create steps see Creating Seguence Steps on page 17 When you execute a sequence the software automatically applies the settings that are recalled in order from step 0 Step 1 ie oe veri 100 seconds 150 seconds 80 seconds Time Step Step Ramp A single execution of a sequence is complete after the sequence s last step is finished The maxi mum number of steps in a sequence is 600 You can specify the sequence repeat count when writ ing a sequence to the PCR LE to run the sequ
6. Save File Folder Olick below to remove alarms 0 Ni 6 AC F All Phase setti DG U phase 5 e M woor W phase 10 e M O Range GL H Frequency Setting Freguency 50 ke Hz Set B O Wave Bank Holding the peak current lears the peak 410 WB No U phase SineWave W phase SineWave 0 s Result OK OutputON Output Output on phase O Monitor Voltage Current Power Z Power Factor Range Lo Modes AG voice SOONG oo MSI E KO gee verse M o LOOSE a MOOSTE eps ne GOOSEN Monitor Setting Monitor Interval 1000 lt ms Save File 0 deg E Output off phase ms dee Displaying Voltage Displaying Current 9 RMS 6 RMS Peak O Peak Average Average Click below to remove alarms cm Close 73 74 Controlling the PCR LE Directly E Three phase r Remote Control Panel 3phase Range AC Voltage Settine SL U phase 100 M Set V All Phase setting T H V phase 100 M Set W phase 100 M Frequency Setting Frequency 50 Hz Set B ave WB No U phase SineWave V phase SineWave W phase SineWave Result OK OutputON Output Monitor Status O Voltage Current Power 6 Uphase 100007 M 0 005 A 0 000 w ON OFF Vphase 100008 m 0004 a 0 000 Output on phase 0 0 Output off phase 0 dee Set Click below to
7. OK i Cancel Change the number of scale lines to change the grid Select the Dot check boxes to display scales using dotted lines Run dialog box Right click the graph and then click Number of scale lines to display the Scale lines dialog box Scale lines x axis Number of scale lines 5 Y axis Number of scale lines 5 Change the number of scale lines to change the grid Select the Dot check boxes to display scales using dotted lines SD011 PCR LE Ver 5 5x SD011 PCR LE Ver 5 5x Other Settings Using the mouse pointer to set the Y axis value Move your mouse pointer over the real time monitor graph to display the monitored values If you move the pointer over the X axis the X axis value is displayed If you move the pointer over the Y axis the Y axis value is displayed To change the value current voltage or power to display on the Y axis right click the monitor graph and click Y Axis Value and then Voltage Current or Power Changing the graph color You can change the graph colors used on Graph window or the Run dialog box To change the graph color on the Graph menu click Color Or right click the graph in the Graph window or Run dialog box and click Color The ways in which you can change the colors vary depending on the item that you want to change Graph Graph Run dialog box Run dialog box menu window Setting graph Monitor graph 1 2 3 Background Background color Yes
8. Setting Protection Functions Using Protection Functions Setting Limits Displaying Monitors Displaying Measured Values Creating and Transferring Arbitrary Waveforms Generating Special Waveforms Waveform bank Controlling the PCR LE Directly Setting the Output Voltage Setting the Frequency Turning the output on and off Displaying Measured Values Generating Special Waveforms Waveform bank Controlling the PCR LE Using Com mands Command function search Command ABC search Command Sub system search 1 See the PCR LE Communication Interface Manual 2 See the PCR LE User s Manual JAMI W pjpj Configuring the Interface Before using Wavy configure the interface Using the RS232C interface RI OH Ul BD Check that the PC is connected properly to the PCR LE On the Seguence menu click Interface The Interface dialog box appears Select RS232C COM Port Baudrate O GPIB Address 1 USB i Serial Number C Ethernet IP Address GE Select the COM port Select the baudrate Click Test to check that Wavy can communicate properly with the PCR LE Click OK to close the Interface dialog box SD011 PCR LE Ver 5 5x Configuring the Interface Using the GPIB interface 0000000000000000000000000000000000000000000000000000000000000000000 1 Check that the PC is c
9. Transfer monitored data arb file Transfer the gt waveform Transfer and execute Control the sequence A E PCR LE series or PCR LE2 series AC power supply SD011 PCR LE Ver 5 5x Wavy Overview E Interface The PC in which Wavy is installed and the PCR LE are connected through the RS232C GPIB USB or LAN interface For the connection procedure see Configuring the Interface on page 6 Reference to related manuals SD011 PCR LE Ver 5 5x Interface e RS232C e GPIB e USB e LAN This guide describes how to operate Wavy it does not cover all the features of the PCR LE If neces sary refer to the PCR LE User s Manual and Communication Interface Manual Description in this manual Reference to PCR LE manuals Configuring the Interface Setting Upthe Interface Setting the Seguence Creation Mode Selecting the Output Mode 2P05 PCR LE option only Setting the Output Voltage Setting the Frequency Creating Sequence Steps Using the Sequence Function
10. peak current limit U Phase 58 00 A E Trip A 0 s 0 00 0 00 Set ipeak current limit U Phase 88 00 A Close Select the mode that you will set protection and current limits for Select the output voltage mode AC DC or AC DC that you specified in sequence creation mode Be sure to select the output voltage mode before setting the protection function items NOTE To set protection functions the PCR LE output must be turned off Enter values in the protection function items Setting Unit Value OVP V A value between 0 0 V and 335 5 V AC voltage A value between 474 1 Vand 474 1 V AC DC or DC voltage UVP V A value between 0 0 V and 335 5 V AC voltage A value between 474 1 V and 474 1 V AC DC or DC voltage Detection time of S A value between 1 and 3 settable only for AC voltage OCP activation Set in unit of 1 second steps Click Set The values are sent to the PCR LE and the settings are updated 5 Click OK to close the Protection Setup dialog box SD011 PCR LE Ver 5 5x Setting Protection Functions 0 4080 Setting On the Seguence menu click Protection Setup The Protection Setup dialog box appears A Setup Read Protection OVP 335 6 Vv uvp 90 0 w Detection time of OGP activation 3 s Current Limit Current Limit U Phase 5 00 0 00 0 00 peak current limit U Phase 88 00 0 00 peak current limit U Phase 88 00 2 Select the mode that you wi
11. For details see Creating and Transferring Arbitrary Waveforms on page 62 e The settings are transferred to the PCR LE only when values are assigned to all the step settings 1 Set the voltage Click the AC V or DC V cell enter a value and press Enter 2 Set the voltage transition Double click the Trans AC or Trans DC cell select Step or Ramp from the list and press Enter 31 32 Creating Seguence Steps 3 Set the execution time interval Click the Interval s cell enter a value and press Enter 4 Configure the other settings When you set the voltage voltage transition and execution time interval all other settings are automatically set to their default values To change them click the cells and enter values or double click the cells and select the values from the lists NOTE e Ifyou select one or several voltage or frequency cells and right click and then select Volt age Freguency Replaced a Voltage Freguency Replaced dialog box appears Enter a new value and click Replace to collectively overwrite the values of the selected cells e Ifyou right click a cell and select Trigger waiting step addition a trigger wait step is added below the selected cell E Default step setting values Trig IN off End deg 0 Trig OUT off Pri phase off Output on U offset off Freguency 50 00 U offset deg 0 Trans f Step U offs ramp off WB No 0 UV phase off S Phase FREE UV de
12. follow the procedure below 1 Move the arbitrary waveform file arb to the folder that arbitrary waveforms are saved in The folder for saving arbitrary waveforms is specified in the Environment Setup dialog box For details see Changing the folder that arbitrary waveforms are saved in on page 61 On the Seguence menu click Arbitrary Waveform The Arbitrary Waveform dialog box appears Click Open and select an arbitrary waveform file arb The data ofthe selected file appears Specify WB No 1 to 63 and Phase for single phase three wire and for three phase and click Transfer The arbitrary waveform data is written to the PCR LE waveform bank and is registered in the list of waveform banks in Wavy Click Close SD011 PCR LE Ver 5 5x Creating and Transferring Arbitrary Waveforms Creating arbitrary waveform data using data from an oscilloscope or other instrument SD011 PCR LE Ver 5 5x You can create arbitrary waveform data by importing measurement data files of other instruments such as oscilloscopes and data loggers Wavy can import data files in text format The maximum number of data values that can be imported is 10000 From the imported data select the arbitrary waveform that you want to use and then convert it for PCR LE 1 i W N Maximum 053 Y axis value 1 047 On the Sequence menu click Arbitrary Waveform The Arbitrary Waveform dialog box appears Under Waveforms type
13. it will take time for the IP address to be assigned e When using a direct connection on the COM I F screen in CONFIG settings of the PCR LE set DHCP to off and AUTO IP to on to automatically set the IP address For details see Interface Setup in the PCR LE Communication Interface Manual 5 Click Test to check that Wavy can communicate properly with the PCR LE 6 Click OK to close the Interface dialog box If the PCR LE is no longer recognized If you are not using a fixed IP address the IP address of the PCR LE may change causing the PC to no longer recognize the PCR LE If this happens check the IP address on the COM I F screen in CONFIG settings on the PCR LE and change to the appropriate IP address SD011 PCR LE Ver 5 5x 10 Basic Operation Overview Starting the application When you start Wavy a graph window and a worksheet window for creating a seguence appear side by side In the Graph window edit steps using the mouse In the Worksheet window edit steps by entering values View Graph Worksheet Sequence Tool Window Help a eis BOA o gt ME EEL Ea E KEE EH Worksheet Data Count 0 s fa M 4 000 Graph window Worksheet window 0 000 v 4 Kikusui PCR LE series Normal Seconds AC voltage RS232C Showing the Graph window In the Graph window you
14. on page 76 If you run a long sequence the data displayed on the real time monitor graph increases You can reduce the load on your PC by setting the maximum number of data entries Setting this number will not affect the monitored data that is saved For details on setting the maximum number of data entries see Setting the maximum data size on page 57 49 50 Displaying Monitors You can display monitored values and monitor graphs in the seguence run dialog box Displaying output values in the Run dialog box On the Seguence menu click Monitoring Setup Or click LJ on the toolbar The Monitor Setting dialog box appears Monitor Settimng Run State Display Markeri J Bar Select Items to be Monitored V Current Monitor interval 500 gt ms Vl Voltage Phase Voltage Line Voltage Monitor Graphical Representation V Active Power F Total Value J Current V Reactive Power Total Value V Voltage V Power Factor 1Y Total Value V Reactive Power Save File No Yes Folder C Users Public Documents Wavy Perle uss Unit of Elapsed Time for Output to File for Saved Data Option 9 s 5 V Data right before Run mins H J Data Immediately after End Stop 2 Under Select Items to be Monitored select the items that you want to display the output values of The available items are current voltage active power reactive power and power
15. select Step If the interval step execution time is short a smooth straight line may not be obtained for ramp Ramp Step Increase Decrease Increase Decrease E Setting the Frequency Setting Description Value Frequency Set the step frequency A value between 1 00 Hz to 999 9 Hz Trans f Set the frequency change Step Ramp 1 In the PCR LE user s manual step is denoted as ramp off and ramp as ramp on 2 To change the frequency gradually over a specified time select Ramp To change the value as a step select Step Ramp Step k k i j Increase Decrease Increase Decrease SD011 PCR LE Ver 5 5x Creating Seguence Steps E Setting the output Setting Description Value Output Set the output on off Trig IN Set the trigger wait state on off Trig OUTI 3 5 Set the trigger signal output on off Stat OUT 4 gt Set the status signal output on off 1 For signal I O high level signals are approximately 5 V and low level signals are approximately OV For signal input the operation does not change regardless of whether the terminal on the rear panel of the PCR LE is left open for high or shorted for low If the wiring method is set to single phase three wire or three phase the signal is output or in put to the U phase 2 A sequence pauses and waits for a trigger before executing a step whose Trig IN is set to on If you click Contin
16. 0 1 ms to 10000 0 ms 0 1 ms s seconds 0 001 sto 1000 000 s 1 ms min minutes 0 1 min to 1000 0 min 0 1 min h hours 0 1 h to 1000 0 h 0 1h Set the output voltage mode for the sequence Select AC voltage DC voltage or AC DC voltage The available options vary depending on the wiring method AC voltage DC voltage AC DC voltage Single phase two wire Yes Yes Yes Single phase three wire Yes Yes Single phase three wire Yes two phase output Three phase Yes 1 Voltage waveforms in which AC has been overlaid on top of DC and voltage wave forms in which DC has been overlaid on top of AC are generated If you specify AC DC voltage you can set the default DC voltage to use when you are creat ing seguence data In the Default DC voltage box enter a value 431 0 V to 431 0 V There are three significant decimal places x xxx The actual number of significant decimal places varies depending on the PCR LE that the PC is connected to 5 Set the output voltage range for the sequence to L or H The maximum output current varies depending on the output voltage range The maximum output current of the H range is half of the that of the L range The output voltage setting ranges for the L range and H range are shown below AC voltage DC voltage AC DC voltage L range O V to 152 5 V 215 5 V to 215 5 V H range OV to 305 0 V 431 0 V to 431 0 V 6 Set the default frequency for the sequence setup s
17. 9 Basic Operation Overview eeeeooooooonooeooeeee 10 Starting the application wusnersenenensenensenenennenennen 10 Executing sequences sssssssosssssssssesesecscsesarararssesseseseeseees 11 Monitoring the PCR LE while running a sequence 12 Controlling the PCR LE scssscsssssscsssssscessecsssssscessecssaes 13 Setting the Sequence Creation Mode 14 Creating Sequence Steps cccccsscccccsscscccccecces 17 Step a1 Od fl arene et anne a 17 Creating and editing steps using the mouse 27 Creating and editing steps by entering values 31 Previewing a SEQUENCE cssscssscscscesesassssssssesssecsesessararesees 34 Saving and Loading a SEQUENCE seccssssseoes 35 Writing or Reading a Seguence eeeeoooeeee 41 Writing a SCOUGI CE EERAARA E 41 Reading a SEQUENCE esssssssssssessssssecsssecessssessssecessecsesecsesees 42 Setting Protection Functions ereeoooooneoeooe 43 Setting the PCR LE Protection FUNCtIONS ms 44 Setting the PCR LE current limits memenseneneenenenei 45 Executing a Sequence oeeoovoneoeonooneseenoneeeee 47 Displaying Monitors sssssecescsssssssscccsosssssssesesso 50 Displaying output values in the Run dialog box 50 Displaying the real time monitor graph uw 51 Changing the monitoring interval 53 Saving Monitored Data
18. Immediately after End Stop 2 Select the Monitor Graphical Representation check box and select the display items current voltage and active power 3 Click OK The Monitor Graph tab and Setting Monitor Graph tab will be added to the Run dialog box Move your mouse pointer over the graph to display the monitored values NOTE For single phase three wire output and three phase output the Setting Moni tor Graph tab does not appear Click the tabs to switch between the different graphs e Run Monitorir JON Output to File provided 500 ms SISI SD Setting Graph Monitor Graph U phase Range C Mode AG 10 000 A 110 0000 1 10 0000W voltage 100010 M cant 4 100 Current 0 005 A Step 0 E Elapsed sie OJA va RS OOOO om e O00 be Pi 20 000 65000 Factor x 0 028 V phase Total Active 10 000 A 1 10 0001V1 10 0000W Vote 100 010 m Power 0 103 w Curent 0004 Ronee O ADOT ber Active p Power 0 041 Factor 0 064 om ma Power 20 000 65000 19 Facto 0 102 phase an 10 000 A 110 000 V1 10 00000 votes 99 997 m The output OFF after 77 the end of execution M Current 0 007 A E Power 0 048 M oe Polar 0 698 var Pi 20 000 65000 Factr 0 069 Monitor graph SD011 PCR LE Ver 5 5x 51 52 Displaying Monitors NOTE Changing the real time monitor graph scale You can change the X axis and Y axis scales of the real time monitor graph
19. SD011 PCR LE Ver 5 5x Creating and Transferring Arbitrary Waveforms SD011 PCR LE Ver 5 5x Enter the voltage to output from the PCR LE in the Set box under RMS Peak Conversion select a value from the Degree list and click Update You can check what kind of values the RMS value V peak value V and THD will take on when the specified voltage is output from the PCR LE when arbitrary waveform data is used If you specify the voltage and harmonic ALL 1 to 40 other values will be calculated automati cally RMS Peak Conversion 1 Enter the voltage to output from the PCR LE 2 Select the harmonic ALL 1 to 40 3 Click Update e 0 0 0 0 0 0 0 0 0 0 1 eb seeeeeeeeeee The RMS peak and THD values are automatically calculated You can check the value for when the set voltage is actually output THD total harmonic distortion is expressed by the following eguation THD 2 Vn 42 Vrms where 2 represents squared n is anumber between 2 and 40 Vn RMS values of the 2nd to the 40th harmonic voltage components Vrms RMS voltage ALL To save the arbitrary waveform data that you have created click Save The data is saved to an arbitrary waveform file arb extension If you do not want to transfer the arbitrary waveform data to the waveform bank the procedure ends here Specify WB No 1 to 63 and Phase for single phase three
20. The file name extension is wvy To overwrite a file that you have already saved on the File menu click Save Or click mj on the toolbar E Viewing saved data You can use Notepad to view saved data I Wavyl wvy Notepad File Edit Format View Help By default data is saved as tab separated values You can change this to comma separated values if you like For the procedure see Changing the file format of sequence data on page 60 The first line contains the conditions common to all steps which was specified in the Sequence Creation Mode dialog box Column 1 Output voltage mode AC AC voltage DC DC voltage ACDC AC DC voltage Column 2 Time unit ms milliseconds s seconds min minutes h hours Column 3 Arbitrary waveform availability 0 arbitrary waveform not available 1 arbitrary waveform available Column 4 Voltage range 0 L range 1 H range Column 5 Wiring method 0 1P2W 1 1P3W 2 3P 3 1P3W 2P The second and subsequent lines contain settings of individual steps The contents vary depending on the output voltage mode and wiring method 35 36 Saving and Loading a Seguence E AC voltage mode 1P2W Column 1 AC voltage Unit V Column2 Time interval The unit is shown in row 1 Column3 AC voltage transition 0 step 1 ramp Column4 Frequency Unit Hz Column 5 Frequency transition 0 step 1 ram
21. When you delete a step the contents of the step are copied to the clipboard Therefore if you insert a step immediately after deleting a step the deleted step will be inserted Keyboard shortcuts To copy a step select a cell and click C or Ctrl C To insert a step select a cell and click V or Ctrl V To delete a step select a cell and click D or Delete Press Z or Ctrl Z to undo the last edit For all of these operations a confirmation dialog box is displayed before the operation is actually carried out 33 Creating Seguence Steps Previewing a seguence You can view the seguence that you are working on in the Seguence Preview dialog box To display the Seguence Preview dialog box on the View menu click Seguence Preview Click Prev or Next to move If you change the content of Click a display span button to to the boundary line of the a step while the preview is open change the time axis display span previous or next step click Update is Sequence Preview a wD The peak V y m e PIW U values of U V a and W phases are displayed The selected items are displayed on the graph Move the cursor over the line to display the voltage V and time ms at that point E Changing the time axis scale To change the time axis scale display span use the display span buttons 50 100 200 400 800 and 1000 or the Time axis scale change dialog box To display the Time axis scale c
22. angle is reached before starting the step To set the starting phase angle or ending phase angle to 360 specify 0 Steps are managed in terms of time If you set E Phase to FIXED and set the ending phase angle the step will end at the specified phase angle For example if you set the ending phase angle of step n to 90 even if the execution of the step n finishes the execution of the next step n 1 will not begin until the phase angle reaches 90 The wait time that is inserted after the execution of a step as a result of setting a phase angle is called phase wait time The phase wait time is dependent on frequency When End deg is not set When the E Phase is set to FREE Step n Step n 1 ROT OT The PCR LE transitions into the next step after the previous step time elapses When End deg is set to 90 When the E Phase is set to FIXED and End deg is set to 90 Step n Step n 1 AO ee Next step Phase wait time The PCR LE waits until the ending phase angle is reached before starting the next step SD011 PCR LE Ver 5 5x SD011 PCR LE Ver 5 5x Creating Seguence Steps Setting Starting phase or Ending phase to FIXED will cause phase wait time to be inserted inthe seguence The PCR LE panel shows the next step during a phase wait time butthe elapsed time remains at 0 until the next step is actually started For example during the phase wait time after the execution of step n 1 the PCR LE panel wi
23. can switch the display item The Y axis on the graph can be changed between voltage frequency starting phase and phase difference For details see Changing the display item in the graph window on page 30 Starting E Phase phase difference angle HShowing the status The test status is displayed at the bottom of the Worksheet window Kikusui PCR LE series 1 Phase 2 Wire Seconds AC voltage IL Range Normal Resolution USB ee 5D011 PCR LE Ver 5 5x Basic Operation Overview Executing seguences e Tocreate a sequence and run it execute steps 2 to 6 e To create an arbitrary waveform and create and run a sequence containing a step that the arbitrary waveform is assigned to exe cute steps 1 to 6 e Toruna sequence that has been created on the PCR LE execute steps 4 to 6 1 Create save and transfer arbitrary waveforms see Creating and Transferring Arbitrary Waveforms on page 62 2 Set conditions common to all steps inthe sequence see Setting the Sequence Creation Mode on page 14 3 Create and save sequence steps see Creating Sequence Steps on page 17 4 Write or read a sequence see Writing or Reading a Sequence on page 41 5 Set the protection functions see Setting Protection Functions on page 43 6 Runthe sequence see Executing a Sequence on page 47 To transfer write an arbitrary waveform file arb that you create
24. control the time when the output is turned off add a step for turning it off at the end of the sequence 2 Click Run The seguence starts The green marker represents the approximate position of execution For seguences that have a large number of repetitions or those that take a long time to run the marker may be off by a large amount e Run Monitoring ON Output to File provided 500fms A Te m an Setting Graph Monitor Graph U phase Range PET Mode AC voltae 86 710 M Cont 3 100 one 0049 w se MUUA Active _9096 w Elapsed 00 00 37 today Power JOS 2 450 var is fone aa 0 000 15 000 V phase Total z vote 86 397 m pate 0130 w cme 0006 o Pattee AMBLAS va power O018 m fore 1401040 Perona 0 800 ver sere Se Facer 0 043 Running W phase Be vtae BEBIA M pn the Curent 0 010 4 face EE recie OABA ivr i i i s Pi 0 000 15 000 Factor M output OFF after end of execution _OFF E L You can change this display to a bar display For the procedure see Execution position dis play on page 50 To abort a sequence that is running click Stop SD011 PCR LE Ver 5 5x 47 48 Executing a Seguence If a step whose Trig IN has been set to on exists the seguence will pause before executing the step To resume the sequence click Continue PAUSE 3 While the seguence is paused the Run button changes to Continu
25. factor You can select multiple items For single phase three wire output or three phase output you can also select Phase Voltage Line Voltage and Total Values If you select the total values for active power reactive power and power factor the total of each phase will be displayed 3 Click OK The Run dialog box will display the output values for the selected items E Execution position display The seguence s execution position display can be set to marker display or bar display To change it set Run State Display to Marker or Bar Monitor Settimng Select Items to be Monitored F Current Monitor interval 500 gt ms SD011 PCR LE Ver 5 5x Displaying Monitors Displaying the real time monitor graph On the Seguence menu click Monitoring Setup Or click Cd on the toolbar The Monitor Setting dialog box appears r Monitor Settimng Run State Display Marker O Bar Select Items to be Monitored Save File No 0 Yes Folder V Power Factor 19 Total Value J Reactive Power Current Monitor interval 500 gt ms Vi Voltage Phase Voltage Line Voltage V Monitor Graphical Representation V Active Power V Total Value J Current V Reactive Power IV Total Value J Voltage C Users Public Documents Wavy Perle ausus Unit of Elapsed Time for Output to File for Saved Data Option s 5 V Data right before Run mis H J Data
26. in offline mode If the communication between Wavy and the PCR LE is offline and you select Direct Control on the Tool menu the message I cannot be connected to PCR LE Is processing continued will appear If you click Yes to open the Remote Control Panel dialog box you will be able to execute offline operations When you change the voltage phase or waveform bank settings the rms line voltage is calculated and displayed E Clearing alarms If a protection function on the PCR LE is activated and an alarm is being generated you can click Clear to clear the alarm If an alarm occurs during sequence execution the Run dialog box status displays UVP See Status indicators on page 49 1 After entering values the Set button will blink until you click it SD011 PCR LE Ver 5 5x Controlling the PCR LE Using Commands SD011 PCR LE Ver 5 5x You can transmit commands from Wavy to control a PCR LE On the Tool menu click Command Control to display the Command Control dialog box Send command IDN Enter a command and then click Run The result will be displayed The command transmission log only the commands that were successfully transmitted and received is recorded in the list box Click Clear to delete this log For details on commands see the PCR LE Communication Interface Manual 77 AAA Error Messages While controlling the PCR LE if you attempt to set a value that i
27. s 29 30 Creating Seguence Steps Changing the display item in the graph window You can change the display item in the graph window The graph Y axis display can be changed to voltage V frequency Hz starting phase angle deg or phase difference deg By default the Y axis displays voltage The X axis always displays the time When creating a step in the Graph window be sure to set the Y axis display to voltage To change the display item right click in the Graph window and select the item Select voltage freguency starting phase angle or phase difference You cannot select multiple items at the same time Transition b Delete ooren E ota rie Vertical Axis Frequency X axis Scale Lines Start phase angle v Y axis Scale Lines Phase difference l Scale Color gt Resolution of time period gt Resolution of setting value gt Draw seguence by step Update Auto Scale E How to view the graph when the Y axis is set to starting phase angle or phase difference When the Y axis is displaying the starting phase angle the absolute position of each phase is displayed When the Y axis is displaying the phase difference the phase difference between each phase is displayed Example The figure below shows how the graphs appear when the seguence output voltage mode is set to single phase three wire and the starting phase UV phase sudden phase change and U phase offset of st
28. seguence For details on the list of waveform banks see Displaying the Waveform View on page 71 In addition you can create arbitrary waveforms by importing text data of measurements taken on instruments such as oscilloscopes and data loggers NOTE e For details on the special waveform output feature of the PCR LE see Generating Special Wave forms Waveform bank in the PCR LE User s Manual The maximum number of arbitrary waveforms that can be registered in the PCR LE is 63 Creating a new arbitrary waveform and transferring it to the waveform bank There are eight types of arbitrary waveforms that you can choose from e Sine e Square e Triangular e Trapezoidal e Peak clipped e Harmonics e Frequency shift e Arbitrary Selecting Arbitrary enables you to directly edit arbitrary waveform data If you select any other type you cannot directly edit the data 1 On the Seguence menu click Arbitrary Waveform The Arbitrary Waveform dialog box appears Double click the waveform to select the corresponding data in the worksheet Arbitrary Waveform gt JE Wave Bank WB No Phase U phase 8191 AN No 272 8151 Waveforms type Sine Square Triangular Trapezoid J Peak clipped 8192 Harmonics 284 8070 0 000 1023 585 8061 Freguency shift ane anc Arbitrary Pead RMS Peak Conversion RMS 0 V Set 0 V Peak 0 Vv Convert Degree THD 0 Close SD011 PCR LE Ver 5 5
29. select Arbitrary and then click Read Select a data file in text format A text data conversion confirmation dialog box appears Set the minimum and maximum values for the X axis and Y axis and then click Update or press Enter The graph display range will change 5 Text Data Conversion NoiseWaveform bt Minimum 059 inh Y axis value 1 059 0 lip alg ub Start 105 i End 211 Tr rk mm ME Convert Return Minimum Y axis value Maximum Y axis value Set the starting and ending positions of the waveform that you want to use as an arbitrary waveform You can also drag the start and end position lines When you drag a line the corresponding data entry in the data sheet is highlighted You can also set the start and end positions in the following manner e While holding down the Shift key double click the waveform The start position line moves to the point you double clicked e While holding down the Ctrl key double click the waveform The end position line moves to the point you double clicked If you double click the following locations the corresponding data on the sheet will be high lighted e The start or end position label or the start or end position line on the graph e Any specific point on the waveform 69 70 Creating and Transferring Arbitrary Waveforms You can right click the waveform and change the colors ofthe start and end position lines Start No 10
30. step to be executed repeatedly For example if Jump Loop of step 3 is set to on Jump Step to 5 and Loop count to 3 the se quence steps will be executed in the following manner 0 1 2 3 4 5 3 4 5 3 4 5 6 and so on 99999 represents infinity 23 Creating Seguence Steps A table of step settings arranged by wiring method E Settings for single phase two wire Output voltage mode Setting AC DC AC DC AC V Yes Yes DC V Yes Yes Interval s Yes Yes Yes Trans AC Yes Yes Trans DC Yes Yes Trig IN Yes Yes Yes Trig OUT Yes Yes Yes Output Yes Yes Yes Frequency Yes Yes Trans f Yes Yes WB No Yes Yes S Phase Yes Yes Start deg Yes Yes E Phase Yes Yes End deg Yes Yes Pri phase Yes Yes Stat OUT Yes Yes Yes Outp Imp Yes Yes Yes Outp Imp Yes Yes Yes Jump Loop Yes Yes Yes Jump Stop Yes Yes Yes Loop Count Yes Yes Yes 1 Depending on the time unit that you specified in sequence creation mode s ms min or h the in terval in the worksheet is set to Interval s Interval ms Interval min or Interval h 2 This setting is available only when the Jump Loop is set up check box under An option setup of a step is selected in the Sequence Creation Mode dialog box SD011 PCR LE Ver 5 5x Creating Seguence Steps E Settings for single phase three wire Output voltage mode
31. the X axis and Y axis scale lines Color Background Change the background color of the graph Line Change the step line color Line to Draw Change the line color that is used when you use the mouse to draw _ lines Vertical Axis Change the vertical axis color X Y axis Change the X axis and Y axis colors XY axes scale lines Change the colors of the X axis and Y axis grid lines Resolution of Default Sets the time resolution of drawn lines time period 1st digit of integer 1st digit of decimal place 2nd digit of decimal place Resolution of Default Sets the voltage resolution of drawn lines setting value 1st digit of integer 1st digit of decimal place 2nd digit of decimal place 3rd digit of decimal place Draw sequence by step Sets the lines to draw to step transition Copy Copies the graph screen to the clipboard Update Auto Scale Applies auto scaling to the graph screen SD011 PCR LE Ver 5 5x 79 80 Menu Reference Worksheet Select All Selects all cells Undo Undoes the previous operation Delete Deletes step data Copy Copies step data Paste Inserts the copied step data Sequence Transfer Read and write sequence data Run Run the sequence Sequence Creation Mode Set conditions that apply to all sequence steps Monitoring Setup Configure monitor settings used during sequence execution Protection Setup Set OVP OCP UVP and UCP Arb
32. today Voltage tv Current a Power Ww 7 Output OFF when End Stop OFF F 0 000 10 000 Monitor graph To save the monitor data configure it before running the sequence For details see Saving Monitored Data on page 54 NOTE e Like the Graph window the display item on the Y axis on the setting graph can be changed between voltage frequency starting phase and phase difference see Changing the setting graph display item on page 48 For single phase three wire output and three phase output the setting monitor graph tab does not appear SD011 PCR LE Ver 5 5x Basic Operation Overview Controlling the PCR LE SD011 PCR LE Ver 5 5x You can use Wavy to remotely control the PCR LE There are two methods for controlling the PCR LE direct control and command control For details on direct control see Controlling the PCR LE Directly on page 73 For details on com mand control see Controlling the PCR LE Using Commands on page 77 To set a waveform bank number using direct control you must on the list of waveform banks click Read or Write to completely synchronize the waveform banks between the PCR LE and Wavy Wordem ven o o E Jaage tet Waveform view Waveform view Direct control View gt Waveform View a vent sae Tool gt Direct Control ew x i Command control gt Tool gt Command Control
33. wire and for three phase and click Transfer NOTE To transfer arbitrary waveform data to a waveform bank you must save the data to a file first The waveform bank items are unavailable until you save the data Wave Bank Select a destination waveform bank number Phase ie For single phase three wire or three phase select also the phase 0 Wite i Click Transfer The arbitrary waveform data is written to the PCR LE waveform bank and is registered in the list of waveform banks in Wavy 7 Click Close 67 68 Creating and Transferring Arbitrary Waveforms Editing an existing arbitrary waveform and transferring it to the waveform bank 1 On the Sequence menu click Arbitrary Waveform The Arbitrary Waveform dialog box appears Click Open and select an arbitrary waveform file arb The data of the selected file appears Edit the settings and click Save The edited data is saved to the file If you do not want to transfer the arbitrary waveform data to the waveform bank the procedure ends here Specify WB No 1 to 63 and Phase for single phase three wire and for three phase and click Transfer The arbitrary waveform data is written to the PCR LE waveform bank and is registered in the list of waveform banks in Wavy Click Close Transferring an existing arbitrary waveform to the waveform bank To use an arbitrary waveform file arb stored in another PC or memory card in a sequence
34. 0 0 000 1000 EI 1 Double click the step that you want to edit A black square is displayed at the step s end point and you can edit the step 2 Move the mouse pointer over the black sguare The pointer changes to a double arrow 3 Drag the pointer up or down to the value that you want to change to The setting changes accordingly SD011 PCR LE Ver 5 5x Creating Seguence Steps Changing the interval step execution time Graph Sequencel A s 1 Double click the vertical line the step division line at the end point of the step that you want to edit A black sguare is displayed at the top of the step division line and you can edit the step 2 Move the pointer over the black sguare The pointer changes to a double arrow 3 Drag the pointer left or right to the value that you want to change to The setting changes accordingly Changing an AC voltage or DC voltage transition step or ramp 1 Double click the step that you want to change A black sguare is displayed at the step s end point and you can editthe step 2 Right click to display a shortcut menu Click Transition and then Ramp or Step The transition of the selected step changes accordingly Deleting a step 1 Double click the step that you want to delete A black sguare is displayed at the step s end point and you can editthe step 2 Right click to display a shortcut menu Click Delete The step is deleted SD011 PCR LE Ver 5 5x
35. 5 0 957 1059 H u 1 059 Start 105 lp End 211 lp ou Y 0957 am 0 925 6 Click Convert A confirmation dialog box appears 7 Click OK The data will be converted X values will be converted into 1024 values ae The 107 points of data from point 105 to point 211 will be converted into 1024 point data Check the minimum and maximum Y axis values Ce 9 Click Return The Arbitrary Waveform dialog box returns The converted data appears in the Arbitrary Wave form dialog box 1 0 Click Save 1 1 Click Close SD011 PCR LE Ver 5 5x HAI 0 p0p0p0 0 Displaying the Waveform View SD011 PCR LE Ver 5 5x Wavy uses the list of waveform banks to manage arbitrary waveforms that have been written to the PCR LE from Wavy and arbitrary waveforms that have been read from the PCR LE into Wavy To display the Waveform View dialog box on the View menu click Waveform View In the Waveform View dialog box you can display waveform images or the list of waveform banks E Waveform image Specify the wave number of an arbitrary waveform from the list of waveform banks and the phase for single phase three wire and for three phase to display an image of the waveform U Phase Sine Wave 8191 E List of waveform banks A list containing the information of the arbitrary waveforms in the list of waveform banks is dis played From this list you can read or write all waveforms wavefo
36. Column8 _ Trig IN 0 off 1 on Column9 Output 0 off 1 on Column 10 Arbitrary waveform number 0 to 63 Column 11 Arbitrary waveform file name U phase arb file name Column 12 Arbitrary waveform file name V phase arb file name Column 13 Starting phase angle control 0 FREE 1 FIXED Column 14 Starting phase angle Unit degrees Column 15 Ending phase angle control 0 FREE 1 FIXED Column 16 Ending phase angle Unit degrees Column 17 Pri phase 0 off 1 on Column 18 U offset 0 off 1 on Column 19 U offset angle Unit degrees Column 20 U phase transition 0 off 1 LEAD 2 LAG Column 21 UV phase 0 off 1 on Column 22 UV phase angle Unit degrees Column 23 V phase transition 0 off 1 LEAD 2 LAG Column 24 Status signal output 0 off 1 on Column 25 Output impedance 0 off 1 on Column 26 Output impedance value Unit Column 27 Jump Loop 0 off 1 on Column 28 Jump Step 0 to 599 Column 29 Loop Count 0 to 99999 1 The arbitrary waveform file name assigned to the specified waveform number in the list of waveform banks See Displaying the Waveform View on page 71 2 This setting is saved only when the Jump Loop is set up check box under An option setup of a step is selected in the Sequence Creation Mode dialog box 37 Saving and Loading a Seguence E AC voltage mode 3P Column 1 AC voltage U phas
37. E2 Series AC power supplies You can use graphs and spreadsheets to intuitively create seguence steps The seguence data that you create are stored and managed in seguence files wvy extension You can transfer them to a PCR LE and execute them when necessary Wavy also allows you to create arbitrary waveform data that can be transmitted using the special waveform output feature of the PCR LE The arbitrary waveform data that you create is saved and managed in individual arbitrary waveform files arb extension You can transfer them to waveform banks in the PCR LE or assign them to steps in seguences created using Wavy You can also use Wavy to monitor and directly control the PCR LE as well as control them using commands HW Main features e Create save transfer and execute sequences e Create save and transfer arbitrary waveforms e Monitor the PCR LE e Directly control the PCR LE as well as use commands to control them Wavy Arbitrary waveforms can be assigned to sequence steps oe MUM ee eS A 2 Ee s a eg Monitor Arbitrary Directly or use commands to control the AC power supply Sequence waveform the AC power Create and save e tees supply Save _ Create and save wvy file Transfer and run F V txt file
38. For single phase three wire output and three phase output you can use All Phase setting to set the same voltage to all phases When setting all phases collectively enter the U phase value You can set the freguency when the output voltage mode is set to AC voltage or AC DC voltage H Voltage measurement and current measurement 37 Specify the values to display on the monitor Select RMS Peak or Average You can select Average only for DC voltage E Range Lor H O Set the voltage range that is used when the output is turned Select L or H on SD011 PCR LE Ver 5 5x SD011 PCR LE Ver 5 5x Controlling the PCR LE Directly E Wave bank O Set a waveform that is registered in a waveform bank Before selecting Wave No be sure to click Read or Write in the Wavy list of waveform banks to synchronize the waveform banks between the PCR LE and Wavy For details on the list of waveform banks see Displaying the Waveform View on page 71 Select a number from the WB No list 0 to 63 check the waveform name that appears and click Set The settings are transferred to the PCR LE and the waveform in the waveform bank is out put from the PCR LE This setting is available when the output voltage mode is set to AC voltage or AC DC volt age Turning the output on and off O Click ON to turn the output on Click OFF to turn the output off The current state of the PCR LE is displayed Output on and off pha
39. G tervalls Trans AC 0 400 0 100 0 400 Step 0 600 0 200 0 200 Ramp 1 000 0 200 0 400 Step Kikusui PCR LE series Normal Seconds AC voltage htervalle Trans AC Trig IN Timels Trig OUT Output Frequency Trans f St 0 0 400 0 100 0 400 Step otf off on 50 00 Step ep 2 0 600 0 200 0 200 Ramp off off on 50 00 Step Step 1 3 1 000 0 200 0 400 Step off off on 50 00 Step Step 2 You cannot edit the Time column To preview the sequence that you are working on see Previewing a sequence on page 34 NOTE SD011 PCR LE Ver 5 5x The first row of the worksheet is step 0 Enter data in order starting from step 0 The voltage transition and frequency transition of step 0 are fixed to Step You cannot change them to Ramp Timels represents the cumulative time from step 0 It is automatically calculated so you cannot change it If phase wait time is created as a result of setting starting phase angles or ending phase angles the actual cumulative time will not match the cumulative time shown in Time s For details on phase wait time see Setting the phase on page 19 e Values that have been entered in cells cannot be deleted To delete them delete the entire step You can cancel the entering or editing of a cell s value by pressing Esc To set WB No to a value different from the default value of 0 you must create save and transfer an arbi trary waveform in advance
40. IX000693 KIKUSUI Operation Guide sequence Creation and Control Software SD011 PCR LE Wavy for PCR LE Ver 5 5X m Run Monitoring ON Output to File provided 500 ms AC_01 10 14_18 23 32 txt Setting Graph Monitor Graph Settine Monitor Graph Range L Mode AC vili v Count 3 100 Step 0 etma 00 00 22 tds votes 0 087 M 3 ouen 0 006 14 ii s Active Power 0 000 w 10 000 A3 10 000CV1 10 000 W The output OFF after the end of execution About This Guide This PDF version of the operation guide is provided so that you can printitin part or in full HCopyrights The contents of this guide may not be reproduced in whole orin part without the prior consent of the copyright holder The contents of this guide are subject to change without notice Copyright 2012 Kikusui Electronics Corporation Table of Contents Tahdkele 705 1757 p HPA 3 Wavy OVEFVIEW sisassasvt ns ninavusi sesivi sei s un vvsivseuisis 4 Reference to related manuals iminernernensennnennennar 5 Configuring the Interface eeeeeoooooooooooooeeee 6 Using the RS232C interface musenersenennennenennenenneneet 6 Using the GPIB interface misnsenersenennenennenseneneneet 7 Using the USB interface uiinernensenennenennensenennenenneneet 8 Using the LAN interface mumnnennenenenneneenensenennenesi
41. TTT Maves PIW 9177 7 7 Waves PAW 017 2 WavesP3wWi U 02 Wave3P3WV 02 Wave3P3WW 02 a 3 Wave3P3W U 03 Wave3P3WV 03 Wave3P3WW 03 s 4 Wave3P3W U 04 Wave3P3WV 04 Wave3P3WW 04 Pes 5 SneWave sine ave TENNENE NENEE E Wava TTS 6 SineWave SineWave SineWave 7 SineWave SineWave SineWave 8 SineWave SineWave SineWave 9 SETE amaan OS amm am OS an Wave3P3W U 10 Wave3P3WV 10 Wave3P3WW 10 x TEE OMA IN SMe n ER N Wavespaw MEA RELGEEEEEE Mlave3P 34 AADI 0NHAAHAMMUAM M Wave 3P3W v 12 EE al SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave SineWave m Arbitrary waveform file name of the registered waveform data All others are default file names In the above example the file name of the waveform data read from the PCR LE arb file name that was automatically saved is displayed NOTE e By default when Wavy starts all waveform names are SineWave e Wavy manages waveform data registered in the list of waveform banks using arb files Therefore when waveform data is read from the PCR LE the d
42. To change the scales right click the real time monitor graph and click Scale to display the Scale dialog box Scale AKI Auto Mir time l a Max time if tl el a Roll mode Mor Heel ringde SC Olin wien The specified ranga 3 i T aes Anita Auf Mir current oO 4 Mex urrerit 10 z 4 Min voltae 0 4 Max valage 10 h Min power ve Max power 10 w If you select the Max time Max current Max voltage Max power Min current Min voltage or Min power check box the auto scale feature will be activated This feature updates the scale values in accordance with the monitored values If the auto scale feature is disabled monitored values that are outside of the range are not dis played on the graph E When the auto maximum time scale is enabled When the auto maximum time scale is enabled you can select roll mode or normal mode e Roll mode The minimum and maximum times of the X axis are scrolled at the same time The display range is defined by subtracting the minimum time setting from the maximum time setting e Normal mode The minimum time is fixed The maximum time is updated to the appropriate value If you select the Scrolling within the specified range check box the graph is scrolled when the monitored values exceed the maximum time of the X axis The amount of time that the graph will be scrolled by is determined by subtracting the minimum time setting and the set scroll time from th
43. V Active Power V Total Value V Current V Reactive Power V Total Value V Voltage V Power Factor 1 Total Value V Reactive Power Save File No Yes Folder C Users Public Documents Wavy Perle usi Unit of Elapsed Time for Output to File for Saved Data Option s 5 VY Data right before Run h mirs H J Data Immediately after End Stop 2 Set Monitor interval Monitor interval range 200 ms to 600 000 ms for single phase two wire output 500 ms to 600 000 ms for single phase three wire output or three phase output 3 Click OK 53 54 JI Wpjpj Saving Monitored Data NOTE If you want to save monitored data be sure to set it before you execute the sequence On the Sequence menu click Monitoring Setup Or click LJ on the toolbar The Monitor Setting dialog box appears ui Monitor Settimng Run State Display Select Items to be Monitored Y Current Monitor interval 500 gt ms Vl Voltage Phase Voltage Line Voltage J Monitor Graphical Representation V Active Power V Total Value V Current V Reactive Power 7 Total Value V Voltage 7 Power Factor V Total Value J Reactive Power No 0 Yes Eolder C Users Public Documents Wavy Perle Unit of Elapsed Time for Output to File for Saved Data Option s S J Data right before Run Demis H VY Data Immediately after End Stop 2 U
44. Yes Yes Yes Line Setting line Yes Yes Yes Line to Draw ute a ATA EE Yes Yes ting is made Vertical Axis Step division lines Yes Yes Yes X Y axis X axis and Y axis Yes Yes Yes Yes X axes Seale Grid lines Yes Yes Yes Yes lines Line that indicates the Line to Run KN Yes position being executed Current line Output current line Yes Voltage line Output voltage line Yes Power line Output power line Yes 1 On the Graph menu click Color 2 Right click in the Graph window and click Color 3 Right click the setting graph of the Run dialog box and click Color 4 Right click the monitor graph of the Run dialog box and click Color 59 Other Settings Changing the file format of seguence data You can change the file format of sequence data On the Sequence menu click Environment Settings to display the Environment Setup dialog box Sequence Data File Format wvy 9 Tab Separation O Comma Separation Monitor Output Data File Format 9 Tab Separation F A File Extension txt 0 Comma Separation Appearance activated when Wavy is restarted New menu style O Classic menu style Arbitrary Waveform Folder C Users Public Documents WavyPcrle data m Canc Under Sequence Data File Format wvy click Tab Separation or Comma Separation The default is tab separation Changing the file format of monitored data You can
45. and save to the PCR LE waveform bank specify the waveform bank number 1 to 63 and the phase only for single phase three wire output and three phase output and execute the transfer Set the wiring method Sequence gt Arbitrary Waveform output voltage mode etc Arbitrary waveforms that are in the list of waveform banks in Sequence creation mode f 3 f a the waveform view can be assigned to steps in a seguence Sequence gt Sequence Creation Mode _ To assign an arbitrary waveform to a step set Wave No of ee EEE N the step to the appropriate waveform bank number 1 to 63 Arbitrary waveforms that are ee V li transferred to the PCR LE are registered in the list of waveform banks Set the number of sequence repetitions when writing a sequence To write the arbitrary waveform data assigned to 4 Tan steps when writing a sequence to the PCR LE Transfer 7 If you select the Read ars Wave check box when reading a seguence from a Sequence gt Transfer the PCR LE the waveform q will be registered in the list of waveform banks select the Write Wave check box Waveform view f s i You can also read the Protection settings from the PCR LE settings Sequence gt Protection Setup ET gt Run H You can monitor the PCR LE at the same time SWIM On the list of waveform banks in the waveform view you can read and write all waveforms excluding Wave No 0 To comp
46. ata is automatically saved in a arb data file File names are automatically assigned on the basis of wiring methods and waveform bank num bers For example the file name Wave1P2W_U_01 arb indicates that the wiring method is sin gle phase two wire 1P2W and that the waveform bank number is 01 The files are saved to the Arbitrary Waveform Folder that is specified in the Environment Setup dialog box see Chang ing the folder that arbitrary waveforms are saved in on page 61 If a file with the same name exists it is overwritten e Output waveform data is stored in the PCR LE internal memory The memory area for storing the data of one output waveform is referred to as a waveform bank The banks are assigned number from 0 to 63 Waveform bank 0 contains a sine wave data that is used in the PCR LE reference voltage waveform This waveform bank cannot be overwritten SD011 PCR LE Ver 5 5x Controlling the PCR LE Directly SD011 PCR LE Ver 5 5x You can use Wavy to remotely control a PCR LE On the Tool menu click Direct Control to display the Remote Control Panel dialog box E Single phase two wire DT Remote Control Panel 1phase 2wire m 1 Mode DO Voltage Setting DC Voltage Setting Frequency Setting Max 120 M Max 120 M Max 70 Hz 6 AC Step Setting Step Setting Step Setting AC DC OK OutputON Holding a 0 S 7 Voltage 100 009 m Monitor Interval 1000 ms
47. change the file format of monitored data On the Sequence menu click Environment Settings to display the Environment Setup dialog box Sequence Data File Format wvy 9 Tab Separation O Comma Separation Monitor Output Data File Format 9 Tab Separation File Extension txt O Comma Separation Appearance activated when Wavy is restarted 9 New menu style O Classic menu style Arbitrary Waveform Folder C Users Public Documents Wavy Pcrle data mms Cancel Under Monitor Output Data File Format click Tab Separation or Comma Separation The default is tab separation You can also select the file name extension set File Extension to txt csv or log Additionally you can enter the extension Changing the window design You can change the Wavy window design On the Sequence menu click Environment Settings to display the Environment Setup dialog box 60 5D011 PCR LE Ver 5 5x Other Settings Sequence Data File Format kwvy 9 Tab Separation Comma Separation Monitor Output Data File Format 6 Tab Separation SS a File Extension txt X 0 Comma Separation Appearance activated when Wavy is restarted 9 New menu style Classic menu style Arbitrary Waveform Folder C Users Public Documents Wavy Pcrle data ams Under Appearance activated when Wavy is restarted click New menu style or Classic menu style This setting will tak
48. d Cannot be set because an output impedance is set 309 Setting Conflict WAVE BANK Cannot be set because a waveform other than waveform bank No 0 is in use For messages that are not in this list see the PCR LE Communication Interface Manual SD011 PCR LE Ver 5 5x OOo Menu Reference File New Creates a new file Open Open an existing file Save Overwrites the file that you are working on Save As Saves the file that you are working on with a new name Close Closes the file that you are working on Recent File Open a recentfile Send Sends or distributes the file that you are working on in an email Exit Exits Wavy and asks if you want to save any unsaved changes to afile View Toolbar Shows and hides the toolbar Status Bar Shows and hides the status bar Save Position Selects whether to save the window position and size Previous File Selects whether to load the last file that was used when the software starts Waveform View Shows the waveform view Seguence Preview Displays a preview of the seguence Graph Transition Ramp Changes the selected line to a ramp transition Step Changes the selected line to a step transition Delete Deletes the selected line Vertical Axis Shows and hides the vertical axis X axis Scale Lines Shows and hides the X axis grid lines Y axis Scale Lines Shows and hides the Y axis grid lines Scale Changes
49. d the PCR LE In Control Panel click System and Security and then Device Manager under System Device Manager EE 58 File Action View Help e 9 m oe 4 ti yk PC j Computer a Disk drives Bi Niena ads j System devices Universal Serial Bus controllers 4 USB Test and Measurement Devices 9 USB Test and Measurement Device IVI a Sound video and game controllers Check that USB Test and Measurement Device is displayed If the device is not recognized properly you need to set up the PCR LE interface again For details see the PCR LE Communication Interface Manual 6 Click OK to close the Interface dialog box If the PCR LE is no longer recognized If the PC enters sleep mode it may stop recognizing the PCR LE If this happens disconnect the USB cable and connect it again SD011 PCR LE Ver 5 5x Configuring the Interface Using the LAN interface 1 Check that the PC is connected properly to the PCR LE 2 On the Sequence menu click Interface The Interface dialog box appears 3 Select Ethernet Interface 5 RS232C COM Port COM1 Baudrate 19200 a Address D USB Serial Number Ethernet IP Address A Test Set the IP address Select the IP address from the list or enter it You can view the IP address on the COM I F screen in the PCR LE s CONFIG settings NOTE If the PCR LE is connected directly to the PC with a crossover cable
50. e During test execution the menus and toolbar are disabled In addition the Run dialog box cannot be resized You can change the size of the Run dialog box when a sequence is not run ning 3 To manually turn off the output click OFF under Output OFF when End Stop When a sequence is running OFF is disabled Changing the setting graph display item You can change the display item on the setting graph The graph s Y axis display can be changed to voltage V frequency Hz starting phase angle deg or phase difference deg By default the Y axis displays voltage The X axis always displays the time To change the display item right click in the Graph window and select the item Select voltage fre quency starting phase angle or phase difference You cannot select multiple items at the same time M voltage iy te 4 Vertical Axis Frequency v X axis Scale Lines Start phase angle m Y axis Scale Lines Phase difference Scale Color For details on how to view the graph when the Y axis is set to starting phase angle or phase differ ence see How to view the graph when the Y axis is set to starting phase angle or phase difference on page 30 For details on changing the scale see Changing the X axis and Y axis scales on page 58 Information displayed during execution Range Displays the range Mode Displays the output voltage mode specified in the Seguence Creation Mode dia lo
51. e Unit V Column 2 AC voltage V phase Unit V Column 3 AC voltage W phase Unit V Column 4 Time interval The unit is shown in row 1 Column5 AC voltage transition 0 step 1 ramp Column6_ Frequency Unit Hz Column 7 Frequency transition 0 step 1 ramp Column 8 Trig OUT 0 off 1 on Column9 Trig IN 0 off 1 on Column 10 Output 0 off 1 on Column 11 Arbitrary waveform number 0 to 63 Column 12 Arbitrary waveform file name U phase arb file name Column 13 Arbitrary waveform file name V phase arb file name Column 14 Arbitrary waveform file name W phase arb file name Column 15 Starting phase angle control 0 FREE 1 FIXED Column 16 Starting phase angle Unit degrees Column 17 Ending phase angle control 0 FREE 1 FIXED Column 18 Ending phase angle Unit degrees Column 19 Pri phase 0 off 1 on Column 20 U offset 0 off 1 on Column 21 U offset angle Unit degrees Column 22 U phase transition 0 off 1 LEAD 2 LAG Column 23 UV phase 0 off 1 on Column 24 UV phase angle Unit degrees Column 25 V phase transition 0 off 1 LEAD 2 LAG Column 26 UW phase 0 off 1 on Column 27 UW deg Unit degrees Column 28 W phase transition 0 off 1 LEAD 2 LAG Column 29 Status signal output 0 off 1 on Column 30 Outputimpedance 0 off 1 on Column 31 Output impedance value Unit Column 32 Jump Loop 0 off 1 on Column 33 Jump Step 0 to 599 Column 34 Loop Count 0 to 99999 1 The arbitrary waveform file name assigned t
52. e able to obtain the output voltages necessary to change the harmonic waveform levels and phases while keeping the fundamental waveform constant r and click Update or press Enter You cannot ps If you specify the fundamental waveform unit V and update you will be able to obtain the out put voltage settings necessary to change the harmonic waveform levels and phases while keep ing the fundamental waveform voltage constant 65 66 Creating and Transferring Arbitrary Waveforms HFreguency shift Arbitrary Waveform J r 4 EE x Wave Bank WB No 1 v Phase U phase Transfer Waveforms type Sire Square Triangular Trapezoid Peak clipped Harmonics Frequency Shiti Arbitrary Read Degree THD 0 Enter a value between 40 00 and 120 00 Enter the frequency shift and click Update or press Enter Enter the original frequency in the left box and the shifted frequency in the right box Frequency shift range 40 00 to 120 00 E Arbitrary Arbitrary Waveform J A Wave Bank WB No Edit data directly P U ohasa Transfer Waveforms type O Sine To edit the data change the values in the data sheet cells Right click a cell and select Copy Paste or Series Paste to copy or paste data To paste to consec utive cells select the cells right click and select Series Paste The value of the first selected cell will be pasted to the selected cells
53. e by the specified angle By offsetting the U phase you can suddenly change the phase of one or two phases and sweep the phase If you offset the U phase the U V and U W phase difference settings the UV and UW phase an gles specified by setting UV phase and UW phase to on will be different from the actual U V and U W phase differences f Offset phase U Reference phase The angle specified by UV U U phase angle with UV phase a set to on is the same as the actual phase difference The angle specified by UV phase Value angle with UV phase set to on is different from the actual phase difference Actual phase difference W V W V When U phase offset and When UV phase difference is UV phase difference are set set but U phase offset is not Therefore if you do not need to sweep the phase we recommend that you set the U phase off set to off For details see Phase sweep in the sequence tutorial To open the sequence tutorial from the Start menu select All Programs Kikusui SD011 PCR LE and then Sequence Tutorial English SD011 PCR LE Ver 5 5x SD011 PCR LE Ver 5 5x 2 Creating Seguence Steps The phase change that you specify when you want to sweep the phase To gradually change the phase over the specified time set this to LEAD or LAG This is effective for varying the line volt age Advance the phase LEAD Delay the phase LAG over the step interval over the step interval For details see Pha
54. e effect when you restart Wavy Changing the folder that arbitrary waveforms are saved in You can change where the arbitrary waveform data files are saved The waveforms that you create and edit in the Arbitrary Waveform dialog box will be saved in this folder NOTE When Wavy recalls a sequence if the arbitrary waveform files are not in their appropriate location Wavy may assign unintended waveforms Sequence Data File Format kwvy 9 Tab Separation Comma Separation Monitor Output Data File Format 9 Tab Separation an A File Extension txt v 0 Comma Separation Appearance activated when Wavy is restarted 9 New menu style Classic menu style Arbitrary Waveform Folder C Users Public Documents WavyPcrle data ms Canc Changing the display format of the Graph and Worksheet windows On the Window menu click Cascade Tile Horizontally or Tile Vertically to change the way that win dows are displayed SD011 PCR LE Ver 5 5x 67 62 Creating and Transferring Arbitrary Waveforms Wavy allows you to create save and transfer arbitrary waveforms that can be transmitted using the special waveform output feature of the PCR LE When you transfer an arbitrary waveform that has been saved the waveform data is stored in the PCR LE waveform bank and is registered in the list of waveform banks in Wavy Arbitrary waveforms that are in the list of waveform banks can be assigned to steps in a
55. e maximum time setting For example if the minimum time is set to 0 seconds the maximum time is set to 23 seconds and the scroll time is set to 10 seconds the amount of time that the graph will be scrolled by is 23 0 10 13 seconds For single phase three wire output and three phase output if you select normal mode the Scroll ing within the specified range check box is always selected you cannot clear the check box The range of scroll time that you can specify is 4 s to 3600 s for single phase two wire output and 4 s to 600 s for single phase three wire and three phase outputs Changing the time unit of the real time monitor graph You can change the time axis unit s or h min s of the real time monitor graph Right click the real time monitor graph to display a menu To set the unit to seconds click X axis Unit and then s To set the unit to hours minutes seconds click X axis Unit and then h min s SD011 PCR LE Ver 5 5x Displaying Monitors Changing the monitoring interval SD011 PCR LE Ver 5 5x Monitor Settimng You can change the monitoring interval On the Seguence menu click Monitoring Setup Or click LJ on the toolbar The Monitor Setting dialog box appears Run State Display Markeri D Bar H Select Items to be Monitored V Current Monitor interval 500 gt ms V Voltage Phase Voltage Line Voltage V Monitor Graphical Representation
56. e phase difference only when the wiring method is single phase three wire or three phase Setting Description Value UV phase 3 Set the UV phase difference on off control UV deg 3 Set the UV phase angle A value between 0 deg and 359 deg UW phase 3 Set the UW phase difference on off control UW deg 3 Set the UW phase angle A value between 0 deg and 359 deg 1 To suddenly change the V phase set UV phase to on and set the UV phase angle 2 To suddenly change the W phase set UW phase to on and set the UW phase angle The UW phase difference can be set only when the wiring method is three phase 3 For details on setting the sudden phase change of the V phase and W phase see Phase setting for multi phase output in the sequence tutorial To open the sequence tutorial from the Start menu select All Programs Kikusui SD011 PCR LE and then Sequence Tutorial English E Setting the phase sweep only when the wiring method is single phase three wire or three phase Setting Description Value U offset Set the U phase offset control on off U offset deg Set the U phase offset angle A value between 0 deg and 359 deg U offs ramp Set the U phase transition off LEAD LAG UV ramp Set the V phase transition off LEAD LAG UW ramp Set the W phase transition off LEAD LAG 1 If you set U offset to on and set the U phase offset angle the U phase will be offset from the ref erence phas
57. ence the specified number of times Risk of malfunction Wavy for PLZ 4W does not check the validity of values it does not check whether values exceed the limits of the device while it executes sequences Do not specify voltages or currents that exceed the specifications of the AC power supply JA CAUTION 1 On the Sequence menu click Sequence Creation Mode Or click ff onthe toolbar The Sequence Creation Mode dialog box appears Sequence Creation Mode Wiring Method J Iphase Swire aphase output phase Time unit n option setup of a step Unit ls v Jump Loop is set up Qutput voltage mode Qutput voltage range 0 AC voltage ut DC voltage D H range J AG DC voltage Default DC voltage Frequency A Default Frequency 50 Default Transition SD011 PCR LE Ver 5 5x Setting the Seguence Creation Mode 2 Select the wiring method You can select 1phase 2wire 1phase 3wire or 3phase If you select 1phase 3wire you can select the 2phase output check box to switch to two phase output When using single phase three wire output the V phase will be the waveform of the U phase with reversed polarity When using two phase output the V phase will be the waveform of the U phase delayed by 180 3 Set the unit of time You can set the step interval unit that is used to create steps to milliseconds seconds min utes or hours Unit Interval setting range Resolution ms milliseconds
58. eps 0 to 3 are set as shown in the following table U S Start U U UV Phase deg offset offset deg a phase KU OM phase StepO FIXED 0 off 0 off on 120 off Step1 FIXED 90 off 0 off on 120 on Step2 FIXED 180 off 0 off on 150 off Step3 FIXED 180 off 0 off on 110 off m When the Y axis display is set to m When the Y axis display is set to Start phase angle Phase difference Drawn based on the starting Drawn based on the starting phase angle and U phase offset phase angle U phase offset and sudden phase change 0 Step 0 iStep 1 iStep 2 Step 3 Step 0 iStep 1 Step 2 Step 3 V phase phase Drawn based on the starting V phase Drawn based on the starting phase angle and U V phase V phase phase angle U V phase difference difference and sudden phase change Step 0 Step 1 Step 2 Step 3 Step 0 Step 1 Step 2 Step 3 SD011 PCR LE Ver 5 5x Creating Seguence Steps Creating and editing steps by entering values In the Worksheet window you can create steps by entering values for the settings The displayed settings vary depending on the settings specified in the Seguence Creation Mode dialog box see A table of step settings arranged by wiring method on page 24 For details on each setting see Step settings on page 17 T Wavy Wavyi File View Graph Worksheet Sequence Tool Window Help D amp M ellis 8 8 oo gt Me 2 M Graph Seguencel EEB V mels A
59. ettings 1 00 Hz to 999 9 Hz and default frequency transition step or ramp Enter the value 1 00 Hz to 999 9 Hz in the Default Frequency box Select Step or Ramp from the Default Transition list NOTE You can set the frequency when the output voltage mode is set to AC voltage or AC DC voltage SD011 PCR LE Ver 5 5x 15 16 Setting the Seguence Creation Mode 7 To use the step jump function select the Jump Loop is set up check box under An option setup of a step For details on step settings see Step settings on page 17 NOTE If you enable the jump function the marker or bar that indicates the approxi mate position of execution will no longer be displayed during sequence execu tion 8 Click OK to close the Seguence Creation Mode dialog box SD011 PCR LE Ver 5 5x Creating Seguence Steps Set the conditions for each seguence step One step corresponds to one operation in the executed seguence Create and edit steps in the Graph or Worksheet window In the Graph window you can set only the output voltage voltage transition and execution time For the procedure to use these windows see the following topics e Creating and editing steps using the mouse on page 27 Graph window e Creating and editing steps by entering values on page 31 Worksheet window The settings that appear in the Worksheet window vary depending on the wiring method specified in sequence creatio
60. f decimal place Always using the voltage transition mode when using the mouse to set steps You can setthe voltage transition mode that is used when you are using the mouse to set steps in the Graph window to Step Right click in the Graph window and then click Draw sequence by step SD011 PCR LE Ver 5 5x Other Settings Setting the maximum data size If you run a long sequence the data displayed on the real time monitor graph increases This will increase the load on the PC which may cause errors To prevent such errors set the maximum data size to reduce the load on the PC Setting this number will not affect the monitored data that is saved Right click the real time monitor graph and click Max Data Count to display the Maximum number of data dialog box Enter the value 10000 to 1000000 the default value is 100000 If the number of monitored data entries exceeds the set value monitored data is deleted starting with the oldest entry One monitored data entry uses approximately 200 bytes When you run a long seguence we recommend that you use Task Manager to check the amount of physical memory being used Changing the graph properties SD011 PCR LE Ver 5 5x You can change the various settings related to the graph in the Graph window or the setting or monitor graphs on the Run dialog box Setting the items to display current voltage and power on the mon itor graph You can set which items a
61. for an ENT key input 199 Operation denied BUSY Denied because the PCR LE is busy 201 Operation denied FREQ The sequence cannot be executed because there is a step whose frequency is outside its limits 112 Operation denied SOURCE 202 Operation denied VOLT The power line abnormality simulation or sequence cannot be executed because there is a step whose voltage is outside the voltage range or limits 203 Operation denied PHASE CHANGE The sequence cannot be executed because there is a step whose trigger wait setting and sudden phase change setting are both turned on 301 Setting Conflict CONPENSATION Cannot be set because the command is in conflict with the compensation setting 302 Setting Conflict CV RESPONSE Cannot be set because the command is in conflict with the response setting 303 Setting Conflict RISE TIME Cannot be set because the soft start output is in progress or the command is in conflict with the soft start setting 304 Setting Conflict SYNCRO Cannot be set because the synchronization function is in use 305 Setting Conflict TRIP 306 Setting Conflict UNBALANCE PHASE 308 Setting Conflict OUTPUT IMPEDANCE Cannot be set because the command is in conflict with the action that is performed when any of the current limits is exceeded Cannot be set because the phase difference is unbalance
62. frequency transition of step 0 in the PCR LE is set to ramp denoted as RAMP ON in the PCR LE user s manual it will be changed to Step after reading the data into Wavy e For details on the folder in which arbitrary waveforms are saved see Changing the folder that arbitrary waveforms are saved in on page 61 e Wavy uses the list of waveform banks of the waveform view to manage the arbitrary waveforms read from the PCR LE waveform banks For details on the list of waveform banks see Displaying the Waveform View on page 71 SD011 PCR LE Ver 5 5x Ea Setting Protection Functions Before executing a sequence set the protection functions and current limits E Protection Protection functions are available on the PCR LE For the setup procedure see Setting the PCR LE Protection Functions on page 44 Setting Description OVP Set the OVP output overvoltage protection value If the output voltage exceeds the OVP setting and remains there for approximately 1 second the output overvoltage protection will be activated UVP Set the UVP output undervoltage protection value If the output voltage drops below the UVP setting and remains there for approximately 1 second the output undervoltage protection will be activated Detection time of OCP Set the time that must elapse after the OCP internal semiconductor activation2 protection is activated before an alarm is generated You can set this value only in AC mode
63. g 180 120 Start deg 0 UV ramp off E Phase FREE UW phase off 1 The sinusoid waveform waveform bank number 0 is standard UW deg UW ramp Stat OUT Outp Imp Outp Imp Jump Loop Jump Step Loop Count off off 240 off off off To select a value different from 0 you must create save and transfer an arbitrary waveform in advance 2 This setting is available only when the Jump Loop is set up check box under An option setup of a step is selected in the Sequence Creation Mode dialog box 3 The default value is 180 for single phase three wire output and 120 for three phase output SD011 PCR LE Ver 5 5x SD011 PCR LE Ver 5 5x Creating Seguence Steps Copying and inserting a step 1 aa Ww N Click a cell in the step that you want to copy You can click any cell in the step On the Worksheet menu click Copy Or right click and then click Copy The step is copied Click a cell in an existing step to specify the copy destination The copied step is inserted before the selected step On the Worksheet menu click Paste Or right click and then click Paste The copied step is inserted before the selected step and the total number of steps increases by 1 Deleting a step 1 2 Click a cell in the step that you want to delete You can click any cell in the step On the Worksheet menu click Delete Or right click and then click Delete The selected step is deleted
64. g box Count Displays the present iteration step Displays the number of the step that is being executed Elapsed Time Displays the elapsed time since the sequence execution started Measured Displays the items current voltage active power reactive power and power values factor that are selected under Select Items to be Monitored in the Monitor Setting dialog box 1 If the sequence is paused in a trigger wait state the number of the step before the step in which Trig IN is set to on is displayed 2 This display may be slightly different from the actual elapsed time 3 For details see Displaying Monitors on page 50 SD011 PCA LE Ver 5 5x Executing a Seguence SD011 PCR LE Ver 5 5x E Status indicators The sequence run dialog box shows one of the following status indicators Standing by standby Running The sequence is running The sequence is paused The sequence has been completed The Stop button has been clicked A communication error has occurred Check the interface settings Error A protection function UVP OVP OCP 0 L 2 OHP or emergency stop has been activated UVP example 1 The sequence will pause before a step whose Trig IN has been set to on Over Load 3 If a PCR LE protection function emergency stop is activated and an alarm is generated you can clear the alarm using the direct control dialog box For details see Clearing alarms
65. hange dialog box right click on the graph and select Scale Time axis scale change After entering a value 1 ms to 600 000 ms click Set The time axis display span changes and Scale ms appears next to the display span buttons E Moving to step boundaries Click Prev or Next to move to the boundary line of the previous or next step E Changing the display item To change the display item U V W U V U W or W U right click on the graph and select the item or select a display item check box above the graph HW Changing the display item color Right click on the graph to select the item and specify the color You can change the color of the line U DC V W U V U W and W U step boundary line background XY axes and XY axis scale lines NOTE IfS Phase of step 0 is set to FREE the starting phase angle of step 0 is displayed as 0 in the sequence pre view graph IfE Phase of the step is set to FIXED and End deg is set to 0 one excessive period of the step may be out put depending on the interval step execution time setting One such example is when the frequency is set to 50 Hz and the interval is set to an integer multiple of 20 ms 34 SD011 PCR LE Ver 5 5x E Saving and Loading a Sequence SD011 PCR LE Ver 5 5x After you have created a sequence save the data to a file Saving a sequence The first time that you save a file on the File menu click Save As Specify the file name
66. here arbitrary waveform files are stored see Changing the folder that arbitrary waveforms are saved in on page 61 SD011 PCR LE Ver 5 5x Oe Wpjp Writing or Reading a Seguence To execute a sequence either write the sequence that you created to the PCR LE or read the sequence in the PCR LE into Wavy Writing a sequence 1 On the Sequence menu click Transfer Or click on the toolbar The Transfer dialog box appears 2 Set the number of seguence repetitions 1 to 99999 99999 represents infinity 3 If the steps in the seguence that you will write to the PCR LE contain arbitrary waveforms select the Write Wave check box If you select the check box arbitrary waveform data assigned to steps will be written to the PCR LE before the seguence data is written Repetition Count Vl Write Wave Status Ready Read Wave 4 Under Write click Run The sequence data that is already set in the PCR LE will be cleared Then the sequence data that you created with Wavy is written to the PCR LE If the Write Wave check box is selected waveform data will be written to the PCR LE before the sequence data is written NOTE The maximum number of arbitrary waveforms that can be transferred to the PCR LE is 63 If there a many steps transferring may take a while If you are writing to the PCR LE when the PCR LE output is turned on and the output voltage mode and output voltage range in the seg
67. ied waveform number in the list of waveform banks See Displaying the Waveform View on page 71 2 This setting is saved only when the Jump Loop is set up check box under An op tion setup of a step is selected in the Sequence Creation Mode dialog box 39 40 Saving and Loading a Seguence NOTE E DC voltage mode 1P2W and 1P3W Column 1 DC voltage value Unit V Column2 Time interval The unit is shown in row 1 Column 3 DC voltage transition 0 step 1 ramp Column 4 Trig OUT 0 off 1 on Column 5 Trig IN 0 off 1 on Column6 Output 0 off 1 on Column 7 Status signal output 0 off 1 on Column 8 Output impedance 0 off 1 on Column9 Output impedance value Unit Column 10 Jump Loop 0 off 1 on Column 11 Jump Step 0 to 599 Column 12 Loop Count 0 to 99999 1 This setting is saved only when the Jump Loop is set up check box under An op tion setup of a step is selected in the Sequence Creation Mode dialog box Loading a saved sequence n al On the File menu click Open Or click Ee on the toolbar Then select a sequence file wvy If you assigned arbitrary waveforms to steps in the sequence manage the relevant arbitrary wave form files arb along with the sequence file wvy in your PC When Wavy recalls the sequence if the arbitrary waveform file is not in the specified location Wavy may assign an unintended waveform For details on w
68. itrary Waveform Create and edit arbitrary waveforms Interface Set the conditions that are used to connect to the PCR LE Environment Settings Set the text file format Tool Direct Control Directly control the PCR LE Command Control Enter commands to control the PCR LE Window Cascade Displays cascaded windows Tile Horizontally Displays horizontally tiled windows Tile Vertically Displays vertically tiled windows Arrange Icons Arranges icons at the bottom ofthe window Help Help Topics Opens the helpfile About Wavy Displays the program information version and copyright 1 There is also a toolbar button for this command SD011 PCR LE Ver 5 5x KIKUSUI ELECTRONICS CORP 1 1 3 Higashiyamata Tsuzuki ku Yokohama 224 0023 Japan Tel 81 45 593 7570 Fax 81 45 593 7571 Website http www kikusui co jp en
69. k clipped Harmonics Frequency shift O Mbinary Read Enter a value between eum Automatically set 0 0 and 100 Enter the duty ratio and click Update or press Enter You cannot directly edit the waveform data Duty ratio range 0 0 to 100 HPeak clipped sine waveform Arbitrary Waveform arm Wave Bank WB No Phase U phase Waveforms type Sine Square Triangular Trapezoid Peak clipped Harmonics Frequency shift O binary Read Enter a value between 0 1 and 100 0 Enter the crest factor and click Update or press Enter You cannot directly edit the waveform data Crest factor range 0 1 to 100 0 SD011 PCR LE Ver 5 5x Creating and Transferring Arbitrary Waveforms SD011 PCR LE Ver 5 5x HHarmonics Arbitrary Waveform i D Enter a value between Enter a value batan 0 00 and 100 00 0 0 and 359 9 Enter the level and phase in each harmonic orde directly edit the waveform data Level range 0 00 to 100 00 in 0 01 ste Phase range 0 0 to 359 9 Harmonic order range 1st to 50th Sx Wave Bank WB No Phase U phase v Transfer Waveforms type Sine Square Triangular Trapezoid Peak clipped Harmonics Frequency shift Arbitrary Read BEBE m Fundamental wave m H 0 Vv H Vannunununn Deeree THD 0 n If you specify the fundamental waveform and update you will b
70. ld read this guide This operation guide is intended for users who will use SD011 PCR LE Wavy for PCR LE to con trol PCR LE series AC power supplies and instructors of such users Explanations are given under the presumption that the reader has knowledge of the electrical aspects of AC power supplies Related manuals For details about the AC power supply see the PCR LE or PCR LE2 Series User s Manual For details on the communication interface see the PCR LE or PCR LE2 Series Communication Interface Manual Trademarks Microsoft and Windows are trademarks of Microsoft Corporation in the United States and or other countries All other company and product names used in this guide are trademarks or registered trade marks of their respective owners Notations used in this guide In this guide Sequence Creation and Control Software SD011 PCR LE Wavy for PCR LE is referred to as Wavy for PCR LE or Wavy e In this guide the PCR LE or PCR LE2 Series AC Power Supply is referred to as the PCR LE The term PC is used to refer generally to both personal computers and workstations The following markings are used in this guide Indicates a potentially hazardous situation which if ignored may result in AA CAUTION damage to the product or other property NOTE Indicates information that you should know Wavy Overview Wavy is a seguence creation and control software application for the Kikusui PCR LE or PCR L
71. letely synchronize the waveform banks between the PCR LE and Wavy you need to write or read on the list of waveform banks To read the waveform bank data from the PCR LE when reading a sequence from the PCR LE select the Read Wave check box gt Transfer write Write Ajddns 1amod 24 wo 2491119 Write ODLDGOGGGGGDGGGESEEEEEEE HHRHRHBRHHHHHHHHEHEEHE EH E Run Waveform data is transferred written to the PCR LE waveform bank PCR LE SD011 PCR LE Ver 5 5x gt 11 12 Basic Operation Overview Monitoring the PCR LE while running a seguence During seguence execution you can monitor the PCR LE output values current voltage active power reactive power and power factor in a Run dialog box The Run dialog box can display a monitor graph For the procedure to display output values and the monitor graph see Displaying Monitors on page 50 If you enable the monitor display the Run dialog box will show a setting graph monitor graph and setting monitor graph only for single phase two wire output Click tabs to switch between the different graphs Click the tabs to switch between the different graphs Run Monitoring ON Outp to File provided 1000 ms lo le E Setting Graph Monitor Graph Setting Monitor Graph Range Mode a 8 000 4 8 0000v7 8 0000 Count aa Elpsed 00 00 00
72. ll show step n The status signal is output while the waveform of the step whose status signal is set to on is being output Panel display ep pg IED a Seoni Phase wait time Sienn Elapsed time a rn TT passe Specified phase angle Status signal a Step n ON Status signal E Step n 1 ON Trigger signal Step n ON Be careful if you want to output signals continuously without sudden phase changes For ex ample if you set the starting phase angle of step n and the ending phase angle of the previous step n 1 the phase wait time between the completion of step n 1 and the start of step n may be as long as one period To prevent this sort of confusion we recommend that you set only the starting phase angle if you want to output steps continuously If you set sudden phase change to on the starting phase of the step and the ending phase of the previous step are automatically set to FIXED and the phase will make a sudden change For example if you set sudden phase change of step n to on the starting phase of step n and the ending phase of the previous step n 1 are automatically set to FIXED and the phase will make a sudden change If you set the starting phase angle of step n to 270 and the ending phase angle of step n 1 to 90 when the execution of step n 1 finishes and the phase angle reaches 90 the exe cution of step n will begin immediately Step n 1 Step n 21 Creating Seguence Steps E Setting th
73. ll set protection and current limits for Select the output voltage mode AC DC or AC DC that you specified in sequence creation mode Be sure to select the output voltage mode before setting the current limit items The current limit setting range varies depending on the output voltage mode To set current limits the PCR LE output must be turned off NOTE 3 Enter values in the current limit items The setting range of each item varies depending on the PCR LE model that you are using and the output mode HW PCR LE series Current limit peak peak AC 2 DC and ACDC current limit current limit PCR500LE 0 05 A to 5 50 A 0 35 A to 3 85 A 0 50 Ato 22 00 A 0 50 A to 22 00 A PCR1000LE 1 00Ato11 00A 0 70 A to 7 70 A 1 00 A to 44 00 A 1 00 A to 44 00 A PCR2000LE 2 00 Ato 22 00A 1 40Ato15 40A 2 00Ato88 00A 2 00 A to 88 00 A PCR3000LE 3 00 A to 33 00A 2 10Ato23 10A 3 00A to 132 00A 3 00 A to 132 00 A PCR4000LE 4 00 A to 44 00 A 2 80 A to30 80A 4 00Ato176 00A 4 00 A to 176 00 A PCR6000LE 6 00 Ato 66 00 A 4 20 A to46 20A 6 00 Ato 264 00 A 6 00 Ato 264 00 A PCR9000LE 9 00 Ato 99 00 A 6 30At069 30A 9 00 A to 396 00 A 9 00 Ato 396 00 A 1 Applies to all output voltage modes 2 Output voltage mode specified in the Sequence Creation Mode dialog box SD011 PCR LE Ver 5 5x 45 46 Setting Protection Functions MPCR LE2 series PCR6000LE2 Single phase output Current limit AC 6 00 A t
74. mit For AC voltage you can also set the length of time 0 s to 10 s that must elapse after the current limit is exceeded until the output is turned off 1 If you select the Trip check box the output will be turned off when a current exceeding the cur rent limit flows If the check box is not selected the output voltage is controlled so that the cur rent does not exceed the current limit The output is turned off at the following times when a current exceeding the current limit flows For AC voltage After the specified length of time elapses or after 10 seconds if the length of time is not set For DC voltage or AC DC voltage 1 second Note that there may be a delay of approximately 0 1 seconds depending on the current mea surement response speed 2 If the length of time until the output is turned off is specified the output will not be turned off until the specified length of time elapses even if a current exceeding the current limit flows for a while This setting can be used to prevent the output from being turned off due to temporary overcurrent such as inrush current SD011 PCR LE Ver 5 5x 43 44 Setting Protection Functions Setting the PCR LE Protection Functions On the Seguence menu click Protection Setup The Protection Setup dialog box appears Protection Setup Sa Protection OVP 0 0 Detection time of OGP activation 3 Current Limit Current Limit U Phase 5 00 A 0 00 i 0 00
75. n mode and output voltage mode Settings that you cannot change are not dis played Frequency Trans f 1 0 400 0 100 0400 Step off off on 5000 Step 0 FR 2 0 600 0 200 0 200 Ramp oft off on 90 00 Step 0 FR 3 1 000 0 200 0 400 Step off off on 50 00 Step 0 FRE NOTE To assign an arbitrary waveform to a step you must create the arbitrary waveform in advance For the procedure see Creating and Transferring Arbitrary Waveforms on page 62 Step settings SD011 PCR LE Ver 5 5x The settings vary depending on the wiring method specified in sequence creation mode and out put voltage mode To the available setting see A table of step settings arranged by wiring method on page 24 For the default setting values see Default step setting values on page 32 E Setting the execution time Setting Description Value Interval s Set the step execution time Interval ms Interval min A value between 0 001 s and 1000 00 s in unit of seconds A value between 0 1 ms and 10000 0 ms in Interval h unit of milliseconds A value between 0 1 min and 1000 0 min in unit of minutes A value between 0 1 h and 1000 0 h in unit of hours 1 Depending on the time unit that you specified in sequence creation mode s ms min or h the interval in the worksheet is set to Interval s Interval ms Interval min or Interval h 17 18 Creating Seguence Steps E Setting the voltage
76. nder Save File select Yes Then specify the save destination The file name will be a concatenation of the output voltage mode and the execution start date and time followed by the extension You can change the file name extension the default is txt 3 Select the unit of the elapsed time that is output to the file Select s or h min 5 s Seconds h min 5 Hours minutes seconds 4 If necessary set the save data options If the Data right before run check box is selected the monitored values before sequence execu tion monitored values at time 0 s will be written at the beginning of the saved data If you select the Data Immediately after End Stop check box the monitored values when the sequence is completed or aborted will be written at the end of the saved data 5 Click OK SD011 PCR LE Ver 5 5x Saving Monitored Data SD011 PCR LE Ver 5 5x E Viewing saved data You can use Notepad to view saved monitored data AC File Time s Current 0 510 020 240 120 330 050 370 080 580 080 1 1 2 2 3 3 4 4 5 4 0 030 ooooooeocs 032 929 031 032 030 034 031 033 029 A 0 0 0 0 0 1 1 2 3 3 voltage v Power W 0 001 J 000 z 000 900 By default data is saved as tab separated values You can switch from tab separation to comma separation For the procedure see Changing the file f
77. o 66 00 A DC land AC DC 4 20 Ato 46 20 A peak current limit 6 00 A to 264 0 A peak current limit 6 00 A to 264 0 A PCR6000LE2 Single phase three wire three phase output 2 00 A to 22 00 A 1 40 Ato 15 40A 2 00 A to 88 00 A 2 00 A to 88 00 A PCR9000LE2 Single phase output 9 00 A to 99 00 A 6 30 A to 69 30 A 9 00 A to 396 0 A 9 00 A to 396 0 A PCR9000LE2 Single phase three wire three phase output 3 00 Ato 33 00 A 2 10 Ato 23 10 A 3 00 Ato 132 0 A 3 00 A to 132 0 A PCR27000LE2 Single phase output 27 00 A to 297 0A 18 90 A to 207 9 A 27 00 Ato 1188 A 27 00 A to 1188 A PCR27000LE2 Single phase three wire three phase output 9 00 A to 99 00 A 6 30 A to 69 30 A 9 00 A to 396 0 A 9 00 A to 396 0 A 1 Only during single phase output and single phase three wire output 4 To turn off the output when the current exceeds the current limit select the Trip check box In AC mode you can set the time that must elapse before the output is turned off To set the time enter the value 0 to 10 in the box below the Trip check box and click Set 5 Click OK to close the Protection Setup dialog box Querying the PCR LE settings Click Read to read the protection and current limit settings that are currently set on the con nected PCR LE The values are displayed and The mode which sets protection current limit is set to
78. o the specified waveform number in the list of waveform banks See Displaying the Waveform View on page 71 2 This setting is saved only when the Jump Loop is set up check box under An option setup of a step is selected in the Sequence Creation Mode dialog box SD011 PCR LE Ver 5 5x SD011 PCR LE Ver 5 5x E AC DC voltage mode 1P2W Saving and Loading a Seguence Column 1 AC voltage Unit V Column2 Time interval The unit is shown in row 1 Column 3 AC voltage transition 0 step 1 ramp Column 4 Frequency Unit Hz Column 5 Frequency transition 0 step 1 ramp Column6 Trig OUT 0 off 1 on Column 7 Trig IN 0 off 1 on Column8 Output 0 off 1 on Column9 DC voltage value Unit V Column 10 DC voltage transition 0 step 1 ramp Column 11 Arbitrary waveform number 0 to 63 Column 12 Arbitrary waveform file name arb file name Column 13 Starting phase angle control 0 FREE 1 FIXED Column 14 Starting phase angle Unit degrees Column 15 Ending phase angle control 0 FREE 1 FIXED Column 16 Ending phase angle Unit degrees Column 17 Pri phase 0 off 1 on Column 18 Status signal output 0 off 1 on Column 19 Output impedance 0 off 1 on Column 20 Output impedance value Unit Column 21 Jump Loop 0 off 1 on Column 22 Jump Step 0 to 599 Column 23 Loop Count 0 to 99999 1 The arbitrary waveform file name assigned to the specif
79. onnected properly to the PCR LE 2 On the Seguence menu click Interface The Interface dialog box appears 3 Select GPIB G Interface RS2320 COM Port COM Baudrate 19200 9 GPIB Address Q r USB k Serial Number C Ethernet IP Address 7 4 Select the GPIB address You can view the GPIB address on the COM I F screen in the PCR LE s CONFIG settings For details see Interface Setup in the PCR LE Communication Interface Manual Click Test to check that Wavy can communicate properly with the PCR LE VI 6 Click OK to close the Interface dialog box NOTE If you are using Windows 8 7 Vista you need to install the latest GPIB driver For details on how to obtain and set up the GPIB driver see the GPIB instruction manual SD011 PCR LE Ver 5 5x Configuring the Interface Using the USB interface 1 Check that the PC is connected properly to the PCR LE 2 On the Sequence menu click Interface The Interface dialog box appears 3 Select USB Ju Interface RS232C COM Port COMI Baudrate 19200 M Address USB 4 Serial Number C Ethernet IP Address 4 Set the serial number Select the serial number from the list or enter it You can check the serial number on the rear panel of the PCR LE 5 Click Test to check that Wavy can communicate properly with the PCR LE If communication fails check whether the PC has recognize
80. or details see Previewing a seguence on page 34 wavy War oloa ile Yn W file View Graph Worksheet od em Sequence Jool Window Help e nne tft gt to 8 Graph window Step division line a e z z Graph Sequencel oE F Graph Seguencel Eaa z F Graph Seguencel n Jee z M M M 9 000 4 090 8 000 7 000 ronan 3 0000 10090 E Move the pointer over The step is confirmed the Y axis NOTE Ifthe wiring method is single phase three wire or three phase and the output voltage mode is set to AG you must create steps one step at a time You cannot draw the next step until you have finished drawing all the phases of the present step You cannot enter the steps continuously for a given phase To change the graph scale see Changing the graph scale on page 28 Tochange the step interval unit see Changing the interval step execution time on page 29 1 Move the mouse pointer over the Y axis The pointer becomes a crosshair and a voltage is displayed 2 Drag the pointer to the time and the voltage that you want to set The setting is confirmed and the step settings are entered in the first row of the Worksheet window This completes the creation of step 1 3 If you want to continue creating steps move the mouse pointer over the end point of the step that you have just created When the pointer becomes a c
81. ormat of monitored data on page 60 For single phase three wire output For single phase three wire output monitored data for the U and V phases is saved to a file For three phase output For three phase output monitored data for the U V and W phases is saved to a file 55 56 Other Settings e Setting the mouse resolution used to set steps page 56 e Always using the voltage transition mode when using the mouse to set steps page 56 e Setting the maximum data size page 57 e Changing the graph properties page 57 e Changing the file format of sequence data page 60 e Changing the file format of monitored data page 60 e Changing the window design page 60 e Changing the folder that arbitrary waveforms are saved in page 61 e Changing the display format of the Graph and Worksheet windows page 61 Setting the mouse resolution used to set steps You can setthe mouse resolution used to set steps in the Graph window E Setting the time interval resolution Right click in the Graph window click Resolution of time period and then the resolution that you want to use Default 1st digit of integer 1st digit of decimal place or 2nd digit of decimal place E Setting the value resolution Right click in the Graph window click Resolution of setting value and then the resolution that you want to use Default 1st digit of integer 1st digit of decimal place 2nd digit of decimal place or 3rd digit o
82. p Column6 Trig OUT 0 off 1 on Column7 _ Trig IN 0 off 1 on Column8 amp Output 0 off 1 on Column9 Arbitrary waveform number 0 to 63 Column 10 Arbitrary waveform file name arb file name Column 11 Starting phase angle control 0 FREE 1 FIXED Column 12 Starting phase angle Unit degrees Column 13 Ending phase angle control 0 FREE 1 FIXED Column 14 Ending phase angle Unit degrees Column 15 Pri phase 0 off 1 on Column 16 Status signal output 0 off 1 on Column 17 Output impedance 0 off 1 on Column 18 Output impedance value Unit Column 19 Jump Loop 0 off 1 on Column 20 Jump Step 0 to 599 Column 21 Loop Count 0 to 99999 1 The arbitrary waveform file name assigned to the specified waveform number in the list of waveform banks See Displaying the Waveform View on page 71 2 This setting is saved only when the Jump Loop is set up check box under An option setup of a step is selected in the Sequence Creation Mode dialog box SD011 PCR LE Ver 5 5x SD011 PCR LE Ver 5 5x E AC voltage mode 1P3W Saving and Loading a Seguence Column 1 AC voltage U phase Unit V Column 2 AC voltage V phase Unit V Column 3 Time interval The unit is shown in row 1 Column 4 AC voltage transition 0 step 1 ramp Column 5 Frequency Unit Hz Column 6 Frequency transition 0 step 1 ramp Column7 Trig OUT 0 off 1 on
83. re displayed on the real time monitor graph Right click the monitor graph click Line Display and then select the items that you want to display Current Voltage and Power Showing and hiding the step division lines e Graph window On the Graph menu click Vertical Axis Or click ELIT on the toolbar This will show or hide the step division lines You can also right click in the Graph window and click Vertical Axis e Setting graph in the Run dialog box Right click the graph and click Vertical Axis to show or hide step division lines 57 58 Other Settings Changing the X axis and Y axis scales You can show and hide X axis and Y axis scales You can also change the type of scale lines solid or dotted and the number of scale lines grid Showing and hiding scales Graph window On the Graph menu click X axis Scale Lines or Y axis Scale Lines to show or hide scales Right click the Graph window and then click X axis Scale Lines or Y axis Scale Lines show or hide scales Run dialog box Right click the graph and then click X axis Scale Lines or Y axis Scale Lines to show or hide scales Selecting dotted lines or solid lines and setting the grid Graph window Click f on the toolbar to display the Scale dialog box Scale X axis Auto J Maximum Time 05 Number of scale lines 5 Dot Minimum Time 0 Y axis Auto J Maximum Value 3 E Number of scale lines 5 Minimum Value 0 e Dot
84. remove alarms 3 deg SONTE M 0 006 a 0 000 m W phase U V phase difference deg current s Set Power Factor 0 000 0 000 0 000 Power Factor 0 000 RMS Conversion U V Line voltage 173 089 M V W Line voltage 173 089 M W U Line voltage 173 089 M Clears the peak current Range E Mode AC Elapsed UOGIE Run Stop Monitor Setting Monitor Interval 1000 rider You can control the output voltage mode output voltage range AC voltage settings DC volt age settings frequency settings waveform bank output on and off phases output voltage measurement output current measurement peak current hold peak current clear and phase difference only for single phase three wire and for three phase and monitor the voltage current power and power factor Set all the maximums and minimums to values that are within the specifications of the PCR LE that the software is connected to E Mode 0 Set the output voltage mode Select AC voltage DC voltage or AC DC voltage E Setting the AC voltage DC voltage and frequency 2 Enter values for the AC voltage DC voltage and frequency and then click Set The settings will be transmitted to the PCR LE For single phase two wire output you can also enter step values in the Step boxes and then use the up and down arrow buttons to change the voltage current and freguency
85. rms 1 to 63 excluding 0 to com pletely synchronize the waveform banks between the PCR LE and Wavy To read waveform data from the PCR LE click Read To write waveform data to the PCR LE click Write On the list of waveform banks click Read or Waveform bank 0 contains a sine wave data Write to completely synchronize the waveform that is used in the PCR LE reference voltage banks between the PCR LE and Wavy waveform and cannot be overwritten Sine Wave Sine Ware Sinewave Sinewave Sine Ware Sine Wave Sine Ware Sinewave Sine Wave Sine Wave Sine Wave l d d 4 5 6 8 j l l By default when the software starts all waveform names are SineWave 71 72 Displaying the Waveform View The list of waveform banks is updated when you execute any of the following operations e When waveform data is transferred to the waveform bank from the Arbitrary Waveform dia log box see Creating and Transferring Arbitrary Waveforms on page 62 e If the Write Wave check box is selected when writing a sequence to the PCR LE from the Transfer dialog box see Writing a sequence on page 41 If the Read Wave check box is selected when reading a sequence from the PCR LE from the Transfer dialog box see Reading a sequence on page 42 Waveform View NS 0 72 No WaveName U phase WaveName V phase WaveName W phase 0 SineWave SineWave neWave Si e Waves PaM UOT TT
86. rosshair drag the mouse pointer to the point that corresponds to the time and the voltage that you want to set The setting is confirmed and the step settings are entered in the first blank row of the Work sheet window Repeat this procedure until you have set all the steps SD011 PCR LE Ver 5 5x 27 28 Creating Seguence Steps Changing the graph scale You can change the Graph window s X axis and Y axis scales On the Graph menu click Scale Or click be on the toolbar The Scale dialog box appears You can also right click in the Graph window and click Scale to display the Scale dialog box Scale Mraxle Auto J Maximum Time 05 Number of scale lines 5 il Dot Minimum Time Y axis Auto Vi Maximum Value 3 Mumber of scale lines 5 Minimum Value i Dot If you select the Maximum Time Maximum Value or Minimum Value check box the auto scale fea ture will be enabled This feature automatically updates the scale values to the appropriate values when you enter values to set a step or when you open a saved file If the auto scale feature is disabled settings that are outside of the range are not displayed on the graph If you are using the mouse to set steps the scale will not be updated automatically even if the auto scale feature is enabled To update the scale on the Graph menu click Update Auto Scale Changing the set voltage Graph Sequencel ba z vi 0 300 0 0
87. s not possible on the PCR LE an error message listed below will appear 1 List of error messages Error message 102 Operation denied OUTPUT ON Symptom Denied because the output is on 103 Operation denied PROTECTION Denied because a protection function is activated 104 Operation denied 105 Operation denied OUTPUT OFF OUTPUT COUPLING Denied because the command is in conflict with the output mode Denied because the output is off 106 Operation denied TRIP DISABLE Denied because the action to perform when the current limit is exceeded is set to not to turn the output off DISABLE 107 Operation denied RISE TIME SIM SEQ Denied because soft start power line abnormality simulation or sequence is in prog ress 108 Operation denied WIRING METHOD Denied because the wiring method single phase three wire or three phase is invalid 109 Operation denied EXT OUTPUT OFF Denied because the output has been turned off through external control 110 Operation denied EXT SEQ STOP Denied because a sequence is being executed or stopped through external control 111 Operation denied V PROG Denied because the AC voltage output is being controlled with an external signal Denied because the command is in conflict with the signal source setting 198 Operation denied ENTRY Denied because the PCR LE is waiting
88. se sweep in the seguence tutorial To open the seguence tutorial from the Start menu select All Programs Kikusui SD011 PCR LE and then Sequence Tutorial English E Setting the output impedance Setting Description Value Outp Imp Set the output impedance on off Outp Imp Set the output impedance value 1 to 100 HSetting the jump function Setting Description Value Jump Loop Setting the jump function on off Jump Step 2 Set the jump destination step 0 to 599 Loop Count Set the number of jump repetitions ta 999993 This setting is available only when the Jump Loop is set up check box under An option setup of a step is selected in the Sequence Creation Mode dialog box Normally sequence steps are executed in order from the first step but you can use the jump function to skip steps and re peatedly execute a specific range of steps If the execution time of the jump source step step in which the jump function is enabled by set ting Jump Loop to on or jump destination step step specified by Jump Step is shorter than 500 ms the peak of the output voltage waveform of the following step may clip If this happens set the execution time of the relevant steps to 500 ms or longer To set the range of steps to execute repeatedly set Jump Loop of the jump source step to on and set the Jump Step and Loop count This will cause the steps from the jump source step to the jump destination
89. ses T Set the on and off phases for AC output You can set them separately For single phase three wire output and three phase output set the U phase f Output on Output off Select the Output on phase and Output off phase check boxes enter the phase angles 0 deg to 359 deg and then click Set The settings will be transmitted to the PCR LE These settings are available when the output voltage mode is set to AC voltage or AC DC voltage Monitor O Click Run to start monitoring Click Stop to stop monitoring The time that has elapsed since monitoring began is displayed You can set the monitor interval when monitoring is not running Select the Save File check box to save monitored output values to a file Click Folder to select the file save destination and the unit of the elapsed time that is output to the file The accuracy of the elapsed time varies depending on the PC environment that you are using s Seconds h min s Hours minutes seconds The file name will be a concatenation of the output voltage mode and the execution start date and time followed by the extension You can change the file name extension the default is txt The following items can be monitored Voltage phase voltage or line voltage current active power Power factor only for AC voltage or AC DC voltage Total active power total power factor only for single phase three wire output or three phase output To switch the vol
90. sine wave as the one that is stored in waveform bank 0 E Setting the phase Setting Description Value S Phase 4 Set the starting phase angle FREE FIXED control Start deg gt Set the starting phase angle A value between 0 deg and 359 deg E Phase 4 Set the ending phase angle FREE FIXED control End deg Set the ending phase angle A value between 0 deg and 359 deg Pri phase Set the sudden phase change on off SD011 PCR LE Ver 5 5x 20 Creating Seguence Steps Steps are managed in terms of time If you set S Phase to FIXED and set the starting phase an gle the step will start from the specified phase angle For example if you set the starting phase angle of step n to 90 even if the execution of the previ ous step n 1 finishes the execution of the next step will not begin until the phase angle reaches 90 The wait time that is inserted after the execution of a step as a result of setting a phase angle is called phase wait time The phase wait time is dependent on freguency When starting phase angle is not specified When the S Phase is set to FREE Step n 1 Step n ROOT Previous step The PCR LE transitions into the next step after the previous step time elapses When the Start deg is set to 90 When the S Phase is set to FIXED and Start deg is set to 90 Step n 1 M nd we SEPN le Previous step Phase wait time The PCR LE waits until the starting phase
91. t Yes Freguency Yes Trans f Yes WB No Yes S Phase Yes Start deg Yes E Phase Yes IE End deg Yes Pri phase Yes U offset Yes U offset deg Yes U offs ramp Yes UV phase Yes UV deg Yes UV ramp Yes UW phase Yes UW deg Yes UW ramp Yes Stat OUT Yes Outp Imp Yes Outp Imp Yes Jump Loop Yes a i Jump Stop Yes Loop Count Yes M 1 Depending on the time unit that you specified in sequence creation mode s ms min or h the in terval in the worksheet is set to Interval s Interval ms Interval min or Interval h 2 This setting is available only when the Jump Loop is set up check box under An option setup of a step is selected in the Sequence Creation Mode dialog box SD011 PCR LE Ver 5 5x Creating Seguence Steps Creating and editing steps using the mouse In the Graph window you can create steps by drawing lines with the mouse The settings that you can specify in the Graph window are output voltage voltage transition volt age change and step execution time interval You can change the Y axis display However be sure to display voltage while creating steps For details on how to change the display see Changing the display item in the graph window on page 30 You can also preview the seguence that you are working on F
92. tage display select Phase voltage or Line voltage If you switch the voltage display to Line voltage the voltage monitor items U phase V phase and W phase will change to U V V W and W U only for single phase three wire out put or three phase output 75 Controlling the PCR LE Directly E Holding the peak current The peak current measurement is displayed as an absolute value of the maximum instanta neous current measured Even if you are generating a negative DC voltage the peak mea sured current is displayed as a positive value If you set the current measurement that is displayed on the monitor to Peak the peak cur rent can be held Enter the hold time and then click Set The settings will be transmitted to the PCR LE You can enter a value between 0 s and 10 s or infinity To specify infinity enter a value greater than 10 E Clearing the peak current D To clear the peak current click Clear under Clears the peak current H Phase setting 11 Select U V phase difference and U W phase difference three phase only enter phase angles 0 to 359 and click Set The settings will be transmitted to the PCR LE E RMS conversion D Based on the phase voltage phase difference and arbitrary waveform data the converted RMS voltage between phases are displayed If you change the voltage or phase settings or change the waveform bank the display will change NOTE You can check the rms line voltage
93. the output voltage mode on the PCR LE SD011 PCR LE Ver 5 5x Executing a Seguence After you have finished creating and transferring the seguence and setting the protection func tions you are ready to execute the seguence NOTE To save the monitor data configure it before running the sequence For details see Saving Monitored Data on page 54 On the Sequence menu click Run Or click on the toolbar The Run dialog box appears The figure below shows an example for a three phase output F n E Run Monitoring ON Output to File provided 500 ms P a mame Setting Graph Monitor Graph U phase Range ESI Mode SS Voltage M Count 100 Current A Step ae Acti Elapsed E Posen w Time Oday Reactive E foal i H s Power Fars 0 000 13800 Factor V phase Total Voltage M EE s wm Current A bie var Active Power Power a w Factor KES ae i ower a Pe m m Standby 0 000 13800 Factor W phase Rn Voltage S M The output OFF after the end of execution L OFF E Current A Active ower w Reactive Power var 0 00 a gt s Power jt 0000 13 800 Factor NOTE To turn off the output automatically when the sequence finishes executing when the sequence is aborted or when a protection function is activated select the Out put OFF when End Stop check box e Ifyou want to accurately
94. ue in the Run dialog box see Executing a Sequence on page 47 the sequence will resume Also if you apply a trigger signal pulse width of 10 us or longer to the SEQ TRIG IN BNC connector on the rear panel of the PCR LE the sequence will resume 3 If you set Trig OUT to on the PCR LE will generate a pulse signal with a width of several tens of microseconds from the SEQ TRIG OUT BNC connector on the rear panel when the step is execut ed 4 If you set Stat OUT to on the PCR LE will generate a status signal from the SEQ STAT OUT BNC connector on the rear panel while the waveform of the step is being generated 5 To set the signal polarity on the PCR LE press CONFIG SHIFT OPR MODE and then SIG I O F3 E Setting the waveform bank number Setting Description Value WB No Set the waveform bank number A value between 0 and 63 1 Specify a waveform bank number 0 to 63 that is registered in the list of waveform banks in the waveform view For details on the list of waveform banks see Displaying the Waveform View on page 71 Output waveform data is stored in the PCR LE internal memory The memory area for storing the data of one output waveform is referred to as a waveform bank The banks are assigned number from 0 to 63 Waveform bank 0 contains sine wave data that is used in the PCR LE s ref erence voltage waveform and cannot be overwritten In the factory default settings all wave form banks have the same waveform
95. uence are different from the present settings on the PCR LE a message appears asking whether it is okay to turn off the output This is because the mode and range cannot be changed on the PCR LE when the output is on e Wavy uses the list of waveform banks of the waveform view to manage the arbitrary waveforms written to the PCR LE waveform banks For details on the list of waveform banks see Displaying the Waveform View on page 71 SD011 PCR LE Ver 5 5x 41 42 Writing or Reading a Seguence Reading a seguence NOTE 1 On the Sequence menu click Transfer Or click on the toolbar The Transfer dialog box appears 2 If the steps in the sequence that you will read from the PCR LE contain arbi trary waveforms select the Read Wave check box The waveform data assigned to the steps in the sequence will also be read Arbitrary waveform data that is read is automatically saved to files with arb extension File names are automatically assigned on the basis of wiring methods and waveform bank numbers For example if the wiring method is single phase two wire and the waveform bank number is 01 the name Wave1P2W_U_01 arb is automatically assigned to the file and saved to the Arbitrary Waveform Folder that is specified in the Wavy s Environment Setup dialog box If a file with the same name exists it is overwritten Repetition Count 1 Status Ready 3 Under Read click Run e Ifthe voltage transition or
96. x Creating and Transferring Arbitrary Waveforms 2 Select the arbitrary waveform type Arbitrary waveform data is 14 bits high 8191 to 8191 and 10 bits wide 0 to 1023 Double click the waveform to select the corresponding data value in the sheet 3 Depending on the waveform that you select set the necessary values HRectangular waveform a KA Arbitrary Waveform J i Jii Wave Bank WBNo 1 Phase U phase Transfer Waveforms type Sine Square Triangular Trapezoid Peak clipped Harmonics D Frequency shift Arbitrary Read RMS Peak Conversion RMS 0 V Set 0 V Peak 0 V Degree ALL THDO A Enter a value between Automatically set 0 1 and 99 9 Enter the duty ratio and click Update or press Enter You cannot directly edit the waveform data Duty ratio range 0 1 to 99 9 ETriangular wave Arbitrary Waveform i A j arm Wave Bank WB No v Phase U phase Transfer Waveforms type Enter a value between Automatically set 0 0 and 100 Enter the duty ratio and click Update or press Enter You cannot directly edit the waveform data SD011 PCR LE Ver 5 5x 63 Creating and Transferring Arbitrary Waveforms Duty ratio range 0 0 to 100 HTrapezoidal waveform 3 Arbitrary Waveform 7 _ 2 X Wave Bank WB No v Phase U phase v Transfer J Waveforms type Sine Square Triangular Trapezoid Pea
97. y ecccseeeee 73 Controlling the PCR LE Using Commands 77 Error MESSAGES siiiissisessssennsssssnsexdnesicssnncsensasssenensas 78 List of error MESSAGES c sssssssssssesessssessssscsecessecsesssseesssseseees 78 Menu Reference cccccccccccccscccccccccccssccsscsccecs 79 SD011 PCR LE Ver 5 5x Introduction SD011 PCR LE Ver 5 5x SD011 PCR LE Wavy for PCR LE is a seguence creation and control software application for the Kikusui PCR LE and PCR LE2 Series AC power supplies You can use graphs and spreadsheets to intuitively create seguence steps You can also use the arbitrary waveform creation feature of this software to create waveforms that can be transmitted using the special waveform output feature of the AC power supplies and assign those waveforms to seguences Furthermore you can monitor and directly control the PCR LE as well as control it using commands This operation guide describes how to use this software to create seguences and arbitrary wave forms and how to control the PCR LE Product versions that this guide covers This operation guide applies to version 5 5x of SD011 PCR LE Wavy for PCR LE To check the ver sion on the Help menu click About Wavy PCR LE version SD011 PCR LE Wavy for PCR LE Ver 5 5x is compatible with PCR LE and PCR LE2 series with firmware version 4 0 and later The firmware version appears on the front control panel when the AC power supply is turned on Who shou
Download Pdf Manuals
Related Search
Related Contents
Equator DC 4000 CV Silver Instructions / Assembly 取扱説明書 - Sony Cables Direct CDLSB-805 storage enclosure User Manual User`s Manual パンフレットのダウンロードはこちら Craftsman 5-Drawer Instruction Manual American Standard Ellisse 2705.118 User's Manual LG 55LF6100 55" Full HD Smart TV Wi-Fi Black LED TV Copyright © All rights reserved.
Failed to retrieve file