3042 - Hardware Manual
Contents
1. If the ProDAQ 3042 is used in a non slot 0 position it can be either statically or dynamically configured To configure it statically the logical address switch must be set to a value between 1 and 254 This determines the logical address of the module permanently and can only be altered by changing the setting of the logical address switch To configure the ProDAQ 3042 dynamically the logical address switch must be set to 255 The resource manager will use the VXlbus MODID lines to access and configure the board and assigns a logical address during run time Page 12 of 14 Copyright O 2002 Bustec Production Ltd Bustec Production Ltd World Aviation Park Shannon Co Clare Ireland Tel 353 0 61 707100 FAX 353 0 61 707106 Bustec Inc 35486 Lorain Road North Ridgeville OH 44039 U S A Tel 1 440 327 8930 Fax 1 440 327 89822. 3 1 Overview The ProDAQ 3042 interfaces with the VXlbus via its P1 and P2 connectors and contains two IEEE 1386 1 PCI mezzanine card PMC slots It is user configurable by setting on board jumpers 3 2 Unpacking Before unpacking the ProDAQ module check the exterior of the shipping carton for any signs of damage All irregularities should be noted on the shipping bill The ProDAQ module is shipped in an antistatic package to prevent any damage from electrostatic discharge ESD Proper ESD handling procedures must always be used when packing unpacking or installing any ProDAQ module PMC module or similar Ground yourself via a grounding strap or similar e g by holding to a grounded object Discharge the package by touching it to a grounded object e g a metal part of your VXlbus chassis before removing the module from the package Remove the ProDAQ module from its carton preserving the factory packaging as much as possible Inspect the ProDAQ module for any defect or damage Immediately notify the carrier if any damage is apparent 3 3 Hardware Preparation The ProDAQ 3042 comes factory configured for operating as a VXIbus Slot 0 controller with the Motorola PPCbug debugger installed Depending on the application it might be necessary to change this configuration The ProDAQ 3042 provides software control over most of its configuration options by setting bits in control registers For additional information
3. Hardware Manual ProDAQ 3042 Embedded Slot 0 Controller PUBLICATION NUMBER 3042 XX HM 0100 Copyright 2002 Bustec Production Ltd Bustec Production Ltd World Aviation Park Shannon Co Clare Ireland Tel 353 0 61 707100 FAX 353 0 61 707106 PROPRIETARY NOTICE This document and the technical data herein disclosed are proprietary to Bustec Production Ltd and shall not without express written permission of Bustec Production Ltd be used in whole or in part to solicit quotations from a competitive source or used for manufacture by anyone other than Bustec Production Ltd The information herein has been developed at private expense and may only be used for operation and maintenance reference purposes or for purposes of engineering evaluation and incorporation into technical specifications and other documents which specify procurement of products from Bustec Production Ltd This document is subject to change without further notification Bustec Production Ltd Reserve the right to change both the hardware and software described herein ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual 3042 XX HM Table of Contents a OVERVIEW coc cece E ae occ iio tds 5 2 RELATED DOCUMENTS 0 ccceccecceceeceeceececcecceceeceececceceececeececeecceceeseseeceeseeseeseseeees 6 3 INSTALLATION AND PREPARATION cecceceeceeceececcecceceeceececcecceceececcecceseeseeeeees 7 3 1 OVERVIEW At e pus cence E ces 7 3 2
4. UNPACKING easter etchant ieee nea cee aa ee la a o eet le eS 7 3 3 HARDWARE PREPARATION 2 eccecceceeceececceceeceecueceeaecuecueceeaecaecuecueaesaeenecueseeaeeeteneaees 7 Descriptions aaa 8 DOM Dita AA AAA A RA it Sa ae AAA EAN 8 3 4 INSTALLATION E o E O o EO ee do E dE O E 8 3 4 1 PMC modules oocoococcoccnccccoccnccoconcccconononononcnnnonnnnnnnnnnonnnnnnnnnnnnnnnnnrnnncnnennnnnnnnnns 8 3 4 2 laago DYAN O E OY PARE AAAA todoo E tse Da 8 4 OPERATION cit iris 10 4 1 FRONT PANEL CONNECTORS eccecceceeceececceeceeaeceecueceeaeenecueceeseeaesaeeueseeseeaesuteneaes 10 4 1 1 10 100 Base T POMS 20 5 5 oo oo eo ae 10 4 1 2 DEBUG Porte tna 10 4 2 FRONT PANEL SWITCHES 0cceccecceceeceeceeceececaecuecueceeaecaececeeseeaeeaecueceeaeeeenteneaees 11 4 2 1 AB TROT SS Mic da 11 4 3 LOGICAL ADDRES S SWITCH iaa 11 Copyright 2002 Bustec Production Ltd Page 3 of 14 3042 XX HM ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual List of Figures Figure 1 LAN Connectors Pin Assignment eeren 10 Figure 2 DEBUG Connector and Cable Pin Assignment eeeeeeeeeeeeeeeeeeeeeeeeeeeees 10 Figure 3 Logical Address Switch Location c cccseceeeeeseeeeeeeeeeeeeeeteeeeeeeeeeeeeeeteeeeeeeses 11 Page 4 of 14 Copyright O 2002 Bustec Production Ltd ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual 3042 XX HM 1 Overview The ProDAQ 3042 high performance Slot 0 Controller provides a p
5. debugger firmware If pressed for more then five seconds the Reset function is selected and all on board devices are reset If the board is located in slot 0 and functions as a slot 0 controller a SYSRESET signal is generated Note The dual functionality of the Abort Reset switch depends on the installed firmware If a different firmware then the factory installed Motorola PPCbug debugger is installed the reaction on the ABT RST switch depends on this firmware 4 3 Logical Address Switch The ProDAQ 3042 Slot 0 Controller can operate as either a Slot 0 controller or as an embedded VXIbus controller non Slot 0 When the ProDAQ 3042 is operated as the Slot 0 controller it must be located in the left most slot slot 0 of a VXlbus System Specification Rev 1 3 or higher compatible VXlbus mainframe and be set for logical address zero 0 If the ProDAQ 3042 is operated as an embedded VXIbus controller non Slot 0 it may be located in any other slot and the logical address can be set to any Value between 1 and 255 LSB MSB Figure 3 Logical Address Switch Location Copyright O 2002 Bustec Production Ltd Page 11 of 14 3042 XX HM ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual Figure 3 shows the location of the logical address switch on the ProDAQ 3042 Set each switch to Off for a logical one 1 and to On for a logical zero 0 The picture shows the address switch set to logical address zero 0
6. E master cycles transparently to the VXIbus allowing a VMEbus master the full access to the VXIbus On the VXIbus it allows the full integration of the module in the VXlbus resource management by providing a set of VXlbus compatible configuration registers and a configurable translation window in the VXlbus A24 or A32 address space Accesses to this translation window are forwarded to the VMEbus module s A16 A24 A32 or CR CSR space Programmable interrupt trigger and MODID support both detection and generation 10 MHz clock generation and auto Slot0 detection allow the board to be used as an embedded controller in Slot O and non Slot 0 applications Copyright O 2002 Bustec Production Ltd Page 5 of 14 3042 XX HM ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual 2 Related Documents Bustec Production Ltd Documents Title ProDAQ 3040 6U VME64 to C Size VXI Adapter Hardware Manual Motorola Publication Number 3040 XX HM Motorola Computer Group Documents Title Motorola Publication Number MVME5100 Single Board Computer V5100A IH Installation and Use MVME5100 Single Board Computer V5100A PG Programmer s Reference Guide PPCBug Firmware Package User s Manual PPCBUGA UM PPCBug Diagnostics Manual PPCDIAA UM Page 6 of 14 Copyright 2002 Bustec Production Ltd ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual 3042 XX HM 3 Installation and Preparation
7. J 45 connectors can be used to connect the ProDAQ 3042 to your LAN Assignment TD TD RD 4 AC Terminated AC Terminated RD AC Terminated AC Terminated Figure 1 LAN Connectors Pin Assignment ozv 4 1 2 DEBUG Port ozv The RJ 45 port labeled DEBUG provides an RS 232 serial interface based on a TL16C550 UART controller chip It is asynchronous only 2 This port may be used to connect a terminal to the ProDAQ 3042 to serve as a console for the installed firmware or operating system By default the port is configured for a baud rate of 9600 baud 8 bits per character 1 stop bit per character and no parity ABT RST ProDAQ 3042 DTE PC etc Pin Assignment Pin DB 9 A 1 DCD 4 DTR 2 2 RTS 8 CTS L 3 GND 5 GND A 4 TXD 2 RXD 1 5 RXD 3 TXD D 6 GND n c a 7 CTS 7 RTS A 8 DTR 1 DCD Figure 2 DEBUG Connector and Cable Pin Assignment e Page 10 of 14 Copyright O 2002 Bustec Production Ltd ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual 3042 XX HM 4 2 Front Panel Switches The front panel of the ProDAQ 3042 incorporates a dual function toggle switch labelled ABT RST 4 2 1 ABT RST Switch The ABT RST switch causes an interrupt signal to be generated This interrupt is normally used as an Abort signal for the processor to abort program execution and return control to the
8. fy that the module is seated properly in the P1 and P2 connectors on the backplane Do not damage or bend connector pins 5 Secure the ProDAQ 3042 in the mainframe with the screws in the top and bottom of its front panel and verify proper contact with the traverse mounting rails 6 If your mainframe does not have an auto jumpering feature for the automatic propagation of the IACK and BG signals you might need to set or remove jumpers on the backplane to allow the proper handling of these signal lines Refer to your mainframe documentation for more information 7 If you want to use the factory installed debugger interactively connect the terminal that is to be used as the debugger system console to the DEBUG port on the front panel of the ProDAQ 3042 8 Replace mainframe or system cover s and cable peripherals to the panel connectors as required 9 Reconnect the system to the AC or DC power source and turn the system power on Copyright 2002 Bustec Production Ltd Page 9 of 14 3042 XX HM ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual 4 Operation 4 1 Front Panel Connectors There are three connectors located on the ProDAQ 3042 front panel two 10 100 BaseT Ethernet connectors labeled LAN1 LAN2 and one serial port labeled DEBUG 4 1 1 10 100 BaseT Ports ha The two RJ 45 ports labeled LAN1 LAN2 provide the 10BaseT or ij 100BaseTX Ethernet LAN interface A standard CAT5 network cable Pra with R
9. les PMC modules mount on top of the MVME5100 single board computer part of the ProDAQ 3042 Please refer to the MVME5100 Single Board Computer Installation and Use manual for the steps necessary to install a PMC module on your board 3 4 2 ProDAQ 3042 Before installing the ProDAQ 3042 into your VXlbus mainframe ensure that the jumpers are configured properly any optional PMC modules are installed and the module enclosure is assembled properly Perform the following steps to install the ProDAQ 3042 in your mainframe 1 Attach an ESD strap to your wrist Attach the other end of the ESD strap to an electrical ground The ESD strap must be secured to your wrist and to ground throughout the whole procedure 2 If necessary perform an operating system shutdown on any computer effected by the installation Turn the AC or DC power off and remove the AC or DC power lines from the system Remove mainframe or system cover s as necessary to access the VXlbus slots 3 Remove filler panels from the selected slot if necessary If you intend to use the ProDAQ 3042 as slot 0 controller it must occupy the left most VXlbus slot in the system slot O If you do not intend to use it as slot 0 controller you may install it into any other free slot in your mainframe Page 8 of 14 Copyright 2002 Bustec Production Ltd ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual 3042 XX HM 4 Slide the ProDAQ 3042 into the selected slot Veri
10. owerful fully customizable platform for embedded applications Using Motorola s newest PowerPC embedded single board computer series MVME5100 and Bustec s ProDAQ 3040 6U VME64x to C Size VXlbus adapter it provides the computational power and bandwidth for algorithmic and throughput intensive control test and data acquisition applications Motorola s MVME5100 single board computer series uses the newest PowerPC generation G4 with AltiVec technology and the new PowerPlus II architecture The MPC7410 is a high performance low power implementation of the fourth generation G4 of PowerPC microprocessors from Motorola The MPC7410 implements the full PowerPC 32 bit architecture and is targeted at both portable and computing systems applications Using Motorola s AltiVec technology it integrates traditional scalar processing with a fully independent vector processing engine The new PowerPlus ll architecture provides memory performance of up to 582MB s memory read bandwidth and 640MB s burst write bandwidth as well as full PCI throughput of 264MB s The ProDAQ 3040 6U VME64x to C Size VXIbus Adapter allows the usage of 6U VMEbus boards in a C Size VXlbus system It translates VMEbus cycles into VXlbus cycles and vice versa In addition it houses the extensions necessary for VXlbus devices as there are the configuration registers a trigger and extended interrupt interface MODID support and the 10 MHz clock generation It forwards all VM
11. please refer to the MVME5100 Single Board Computer Programmer s Reference Guide and the ProDAQ 3040 6U VME64x to C Size VXIbus Adapter Hardware Manual Some options are not software programmable but controller by manual installation or de installation of jumpers The following table lists the manually configured jumpers on the ProDAQ 3042 and their default settings Copyright 2002 Bustec Production Ltd Page 7 of 14 3042 XX HM ProDAQ 3042 Embedded Slot 0 Controller Hardware Manual Jumper Description Setting Default J1 RISCWatch header None factory use only J2 PAL programming header None factory use only J4 Ethernet port 2 selection None Only front panel connector supported J6 J20 Operation mode None SBC mode not supported J7 Flash memory selection Pins 1 2 soldered Bank A Bank B Pins 2 3 socketed Bank B J10 J17 Ethernet port 2 selection None Only front panel connector supported J15 System Controller None ee Automatically detected by ProDAQ 3040 adapter J16 Soldered Flash protection Pins 1 2 programming enabled prog Pins 2 3 programming disabled enabled NOTE The settings described here supersede the settings as described in the manual MVME5100 Single Board Computer Installation and Use due to special considerations for using the MVME5100 series board together with the ProDAQ 3040 adapter 3 4 Installation 3 4 1 PMC modu
Download Pdf Manuals
Related Search