HAI OmniTouch Touchscreen
Contents
1. S HAI Home Automation Inc Model 32A00 1 OmniTouch Touchscreen User s Guide Document Number 32R00 1 Rev A August 2003 Copyright 2003 Home Automation Inc ALL RIGHTS RESERVED DESCRIPTION The Model 32A00 1 OmniTouch Touchscreen is a colorful plug and play touchscreen interface for HAI controllers OmniTouch is self configuring based on the programming of your HAI controller Changes made on your system automatically show on the touchscreen allowing you to maintain and reprogram your system remotely OPERATION The touchscreen is designed with everything that is necessary for you to operate and program your HAI system In its normal state the Home page is displayed which shows the day date time current security mode if applicable and current outdoor temperature if applicable At the bottom of the display the system status is shown If all doors windows sensors etc are secure no zones are bypassed and if there are no troubles the bottom line will show SYSTEM OK as seen below Monday June 23 2003 SORTERAT Disarmed m had KU Button FO A o Status System SYSTEM OK The Home page displays an icon for each function that you can perform from the touchscreen According to your system configuration not all icons may be visible as shown above if the option isn t part of your system or if you don t want a touchscreen to access those items Simply touch one of the icons to sel2. ain its light setting until 30 seconds after the room is darkened When changing from a dark setting to light e g the lights in a dark room are turned on the touchscreen will immediately change to its light setting To set the light and dark settings for the ambient light sensor go to the Touchscreen Setup page With the room illuminated set the brightness and contrast to the optimal viewable settings then press the Light icon Then darken the room e g turn off the lights or wait until the sun goes down and set the brightness and contrast to the optimal viewable settings then press the Dark icon Note The brightness and contrast levels must be set higher for the ambient light setting than the brightness and contrast levels set for the ambient dark setting After you exit the Touchscreen Setup page when the light level reaches the light threshold the display will illuminate to the brighter settings when the light level reaches the dark threshold the display will dim to the darker setting Once configured to disable the ambient settings so that the screen is always at the same intensity set the brightness and contrast to the desired levels and then press the Light icon immediately followed by the Dark icon By default the ambient settings are disabled Note In the event of an AC Power failure and the HAI c
3. ect the desired page Control Control units lights appliances outputs and flags scenes and all on off Security Arm disarm security emergency alarms bypass restore zones and go to area Button Activate Button macro programs Temperature Control thermostats temperature sensors and humidity sensors Status View status of lights zones and temperatures view and edit programs System View event log and command voice text messages Setup Configure touchscreen and controller clean screen and create programs TOUCHSCREEN LED The touchscreen LED is used to indicate whether the security system is currently armed or disarmed If armed in any security mode the LED is set to red If the system is disarmed the LED is set to green The LED flashes when a Message is displayed LIST BOXES Selectable items such as units zones buttons temperatures etc are displayed in a list box An item may be selected from a list box by simply touching the item in the list or by pressing the up arrow or down arrow buttons to scroll through list items With each press the next item is highlighted Press enter to select the highlighted item Front Porch Front Foyer Hall Light W NZ 4 Den Light Den Fan Patio Lights Press the page up or page down buttons to scroll through pages groups of items With each press the next group of items is displayed with the first item in the list
4. ess the sun button for the time of Sunrise or the moon button for the time of Sunset Once complete press the OK button to save time If you make a mistake press the Clear button and start over Next specify the day s in which the program will activate 1 20 PM MTWTFSS Monday Friday Saturday Tuesday Weekdays Sunday Wednesday Weekends Thursday at Press Monday Sunday to select the specific day s After a day is selected it may be deselected by pressing the respective button once again The Weekdays button will select Monday Friday and the Weekends button will select Saturday and Sunday Once complete press the OK button to save the day s From the Edit Program page press the Security button to create a program that is activated when the security mode changes to the specified mode Away Vacation Night Night Dly Day Day Inst Disarm Security Press the desired security mode button Once complete press the OK button to save the security mode Note The program will activate at the end of the exit delay if applicable From the Edit Program page touch the Control icon to create a program that controls a unit i e light appliance output or flag From the Edit Program page touch the Temperature icon to create a program that controls thermostats energy saver modules temperature sensors and humidity sensors Control and temperature devices are d
5. highlighted Fire Flag 4 A Window Flag Sprinkler 1 v N Sprinkler 2 Sprinkler 3 Press up arrow to move up one item in the list If you are at the top item in the list the up arrow will bring you to the last item on the previous page Press down arrow to move down one item in the list If you are at the last item in the list the down arrow will bring you to the top item on the next page Press page up to move up to the previous page group of items in the list Press page down to move to the next page group of items in the list Press enter to select the highlighted item Press exit to exit from the current page and return to the Home page You may press and hold the up arrow down arrow page up and page down buttons to quickly scroll through list items and pages SECURITY If security is part of your automation system the following information supplements the information in your controller owner s manual Refer to your controller owner s manual for complete operating instructions Arming and Disarming To arm or disarm the security system from the Home page touch the Security icon Security AWAY Away Vacation i Night Night Dly Day Day Inst More Options Disarm Security Area rt The top line on the Security page displays the current security mode If the system is disarmed and Quick Arm is enabled simply touch the desired secu
6. isplayed in a list boxes The device may be selected from a list box by simply touching the device in the list or by pressing the up arrow or down arrow buttons to scroll through list devices then pressing enter to select the highlighted device Once selected the appropriate command page is displayed for the selected device Porch Light On 25 50 75 1100 Level Ramp Timed Sr Specify the desired command for the selected device SUNSET MTWTFSS Porch Light ON When Command Time e m 2 Security Control Temp E Press OK to save the displayed program or the exit button in the lower right corner to cancel
7. it the Test page SETUP From the Home page touch the Setup icon This will bring you to the Setup page From the Setup page touch the appropriate icon e Screen Setup to configure the operating parameters of your touchscreen e System Setup to configure operating parameters of the automation and security system and for advanced programming of the automated control and security functions e Clean Screen to wipe clean the touchscreen display e Program to create basic automation programs for lighting and temperatures TOUCHSCREEN SETUP The Touchscreen Setup pages allow you to configure the operating parameters of your touchscreen These items only affect the touchscreen from which you are currently operating Touchscreen Setup Brightness Contrast Ambient Setting Light DA DA Backlight On Time C 4 Brightness 0 15 Adjusts the brightness level of the touchscreen display Contrast 0 31 Adjusts the contrast level of the touchscreen display Ambient Setting Sets the light and dark ambient light levels see Ambient Setting in this document for additional information Backlight On Time 0 15 Sets the length of time the touchscreen display remains illuminated after the last time a button is pressed on the touchscreen After the time has expired the touchscreen display turns off Simply touch anywhere on the screen and the display wi
8. ll immediately illuminate A setting of 0 means the touchscreen is always illuminated 0 is not a recommended setting Next Saves the current settings and displays more setup options Press the up arrow button to raise the current setting and the down arrow button to lower the current setting When complete press Next for more options or the exit button in the lower right corner to save the settings and exit back to the Home page Touchscreen Setup Sounder Key Click Enabled Enabled VE WY At Sounder Enables or disables the touchscreen sounder The sounder is used to alert you of errors troubles and messages and emits tones upon entry and exit delays Key Click Enables or disables key clicks a short tone when buttons are pushed on the touchscreen Back Saves the current settings and returns to the previous setup page Press the up arrow button to enable the current option and the down arrow button to disable the current setting When complete press Back to return to the previous setup page or the exit button in the lower right corner to save the settings and exit back to the Home page Ambient Setting The Ambient Setting is used to brighten the touchscreen display in an illuminated room and dim the touchscreen display in a dark room When changing from a light setting to dark e g the lights in the room are turned off the touchscreen will maint
9. nd hold the key for 1 second Emergency Keys Bypass Restore j 4 Restore All Zones Emergency Keys If enabled emergency alarm conditions can be activated through the touchscreen These conditions Fire Police and Auxiliary are initiated when the Police Fire or Aux button is pressed and held approximately 1 second If enabled the Emergency Keys are always armed GOTO If your system is configured with multiple areas it is possible to temporarily assign the touchscreen to a different area All security and control commands will now operate on the selected area just as if you were physically at a touchscreen or console assigned to that area All status displays will show the status of the selected area To go to a different area press the GOTO button An Area list box is displayed Select the area from the list box and then enter a valid code for that area After the last digit of a valid code is entered the touchscreen will display the Home page for the selected area Use the GOTO button again to return to the area normally assigned to that touchscreen STATUS The Status page displays the current status of various items in the system zones security mode energy cost outdoor temperature the time of Sunrise and Sunset and allows you to control view and edit programs for lighting and temperature devices From the Home page touch the Status icon Status on oo Control Zones Temp Te
10. ontroller is running on backup battery power the touchscreen display will be lowered to its lowest viewable setting Do not try to adjust the brightness and contrast levels When AC Power is restored the touchscreen display will automatically return to its correct settings SYSTEM SETUP The System Setup pages allow you to configure operating parameters of the automation and security system and for advanced programming of the automated control and security functions The System Setup pages look and operate similar to an HAI console Refer to your controller owner s manual for complete operating and programming instructions CLEAN SCREEN The Clean Screen page allows you to wipe clean the touchscreen display without activating any ofthe buttons Clean the screen with a soft damp cloth When complete press and hold the Restore button for three seconds to return to the Home page PROGRAM The Program pages allow you to construct and edit basic automation programs for lighting and temperatures You are first prompted to enter a code After the last digit of a valid code is entered the Edit Program page is displayed NEW PROGRAM When Command Time 2 A A Security Control Temp From the Edit Program page press the Time button to create a program schedule that will activate at a specific time on the specified day s Enter the time use either AM PM or 24HR time format Pr
11. ram is highlighted Press the page up or page down buttons to scroll through groups of programs With each press the next group consisting of 2 programs is displayed with the first program in the list highlighted Press the Modify button to modify edit the selected program using the Program pages see Program in this document for information regarding constructing and editing a program Press the Delete button to delete the selected program When pressed a Confirm Deletion page is displayed Press the Delete button to confirm your choice to delete the program Once pressed the program will be permanently deleted from the system If you choose not to delete the program simply press the exit button in the lower right corner Zone Status Touch the Zones icon to view the current status of each zone The display will show the zone name and the current status of the zone Press the page up or page down buttons to scroll through groups of zones Zones that are secure are displayed in green zones that are not ready are displayed in red and zones that are in trouble are displayed in yellow Test Touch the Test icon to check the status of the battery telephone bell circuit auxiliary fuse and security zone loop readings The pages look and operate similar to an HAl console Refer to your controller owner s manual for complete operating instructions When complete press the key to ex
12. rity mode button and the system will immediately begin arming To disarm security arm security from one mode to another or to arm from the disarmed state if Quick Arm is disabled a code is required After you touch the desired security mode or Disarm Security button the Keypad page is displayed Disarm Enter Code 1 2 4 5 718 Clear Enter your four digit code If you make a mistake press the Clear button and start over or press the exit button to return to the previous page After the last digit of a valid code is entered the system will perform the desired task Auto Bypass If Auto Bypass is enabled in your system when you arm security your system will automatically bypass any zones that are left open when the system is armed If Auto Bypass is disabled in your system when you arm security and zones are left open the touchscreen will display System Not Armed Zone s Not Ready Secure the open zone s and then press the Retry button the system will immediately begin arming if all zones are secure Silencing Alarms To disarm the security system after an alarm has tripped or during the entry delay simply press the Disarm button then enter your four digit code on the Keypad page The Disarm key disarms the burglar alarm resets emergency alarms and silences all sirens and sounders Arming and Disarming other Security Areas If your system is configured with mul
13. st 6 43 AM C 5 43 PM 14 TE Security Disarmed Energy Cost Lo y The main Status page displays the time of Sunrise and Sunset for the current day current security mode energy cost and outdoor temperature if applicable According to your system configuration not all icons may be visible as shown above Control and Temperature Status Touch the Control icon or the Temperature icon to view the status of each control and temperature device connected to the system to change the status of a device to view all programs that control the current device and to edit a selected program that controls the device Unit Status Front Porch STATUS OFF Change AV Program N y Press page down to display the next item and press page up to display the previous item Press the Change button to change the status of the selected device To view all of the programs that control the selected device press the Program button To view or edit programs a code is required After the last digit of a valid code is entered a list of programs that control the selected device is displayed Programs Front Porch SUNSET MTWTFSS Front Porch ON SUNRISE MTWTFSS Front Porch OFF Modify 4 Y Delete J IN ar To modify or delete a program highlight a program by simply touching the program in the list or by pressing the up arrow or down arrow buttons to scroll through programs With each press the next prog
14. tiple security areas it is possible to arm other individual areas or all areas from the Security page Before selecting the desired security mode or Disarm Security button first select the Area button The Area list box is displayed with available security areas Select the desired area from the list box or House select All Areas to arm or disarm all security 4 V areas Workshop Guest House J IN After selecting the desired area you return to the Security page where you must select the Enter a desired security mode or Disarm Security A button After you touch the desired security mode or Disarm Security button the Keypad page is displayed In order to arm disarm a different area you must have a Master code or a code that is valid for the selected area Likewise to arm disarm All Areas you must have a Master code or a code that is valid for all areas Even if Auto Bypass is enabled the system will not arm another area if any zones in that area are left open The touchscreen will display System Not Armed Zone s Not Ready Secure the open zone s in the selected area s and then press the Retry button the system will immediately begin arming if all zones are secure More Options To bypass and restore zones activate emergency alarms and go to a different area from the Security page press the More Options button To activate emergency alarm press a
Download Pdf Manuals
Related Search