Model 1030 User Manual - rev
Contents
1. Mier light Skincare System Model 1030 User Manual 77 IOPN231 Rev A Model 1030 User Manual TABLE OF CONTENTS FONC MON sonaba TREA FMEN Tirronen ati INDICATIONS FORUS E picca CONTRAINDICATION Sia aan SEEANIN cicale MAINIENANGE leali CLASSIFICA TION amp SYMBOL S aura A aiai DISINFECTION dS IE RUIZA HON ss as SAFETY PRECAUTIONS gt coi SPECIFICANONS iria CONTACT INFORMATION sa Page 1 Model 1030 User Manual Your Model 1030 system has been designed with a focus on safety simplicity and ease of use You will be pleased with how efficiently the system works FUNCTION If not on switch the power switch on the back of the unit to the on position The red pilot light on the switch will light Note a continuously blinking pilot light indicates a possible power supply problem contact your distributor for assistance Turn the unit on by pressing the black START switch on the top of the unit START Note The unit starts in the RED IR mode skin treatment Pressing the START button a second time switches the unit to the BLUE mode acne treatment Select your mode based on the treatment desired Make sure you read and understand all the information contained in this manual before operating unit Page 2 Model 1030 User Manual TREATMENT Make sure you read and understand all the information contained in this manual before operating unit di Place the protective eye covers on your client2. With eye protection in place a standard light source should be administered to the client The client should confirm Figure 1 that the light could not be seen 2 The client should be in a relaxed comfortable position that will allow the Model 1030 to be placed behind the client with the flexible arm reaching over the head 3 AN Maneuver the flexible arm unit so that the surface of the LED panel is approximately 1 2 away from the Face Figure 1 4 Press the START button to begin the 10 minute treatment Figure 2 5 The unit starts in the RED IR mode skin treatment Pressing the START button a second time switches the unit to the BLUE mode acne treatment Select your mode based on the treatment desired o 6 Align the Model 1030 with the clients face by repositioning as required Figure 2 7 When the session is over swing the unit away from the clients face and remove the eye protection The treatment is complete Page 3 Model 1030 User Manual INDICATIONS FOR USE The Panel Pulsator utilizes Light Emitting Diodes to provide light to the body Generally indicated to e treat dermatological conditions and specifically indicated to treat moderate inflammatory acne vulgaris Blue light e provide topical heating to promote increased blood flow relaxation of muscle and relief of pain Red IR light CONTRAINDICATIONS e Do not use on anyone that is pregnant has epilepsy or is using any medication
3. that is known to cause light sensitivity e g tetracycline or Retin A CLEANING Cabinet As required perform the following A Disconnect the power cord from electrical outlet before cleaning unit A Do not use petroleum based solvents cleaners Do not use liquid directly on the unit A Clean cabinet with mild soap and water applied with a damp cloth wipe dry MAINTENANCE A If the device is observed to not be operating properly then discontinue use immediately and contact your distributor for service A No periodic service maintenance requirements A Calibrated unit Repairs must be performed by the manufacturer and verified to original standards Contact your distributor concerning repair to prevent voiding the warranty A When disposing of this device or any accessories make certain to abide by your local waste disposal regulations CLASSIFICATION amp SYMBOLS ml IEC CLASS Il EQUIPMENT Power Supply is Class Il Equipment Protection from electric shock is 417 5172 achieved by DOUBLE INSULATION A IEC ATTENTION Read and understand all the information contained in this manual before 348 operating unit DISINFECTION STERILIZATION A No disinfection sterilization requirements Page 4 Model 1030 User Manual SAFETY PRECAUTIONS l Use only GlobTek power supply REF GMT21089 1815 T3 REF G1200
4. LCP Y MED Replacement contact distributor request replacement REF 62 0000150 power supply To fully isolate the Model 1030 from the supply mains unplug the AC cord from the power supply The equipment or system should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary the equipment or system should be observed to verify normal operation in the configuration in which it will be used Should interference be noted reorient or relocate the equipment increase separation between the equipment connect equipment into a different circuit 1 EQUIPMENT NOT SUITABLE for use in the presence of a FLAMMABLE ANESTHETIC MIXTURE WITH AIR or WITH OXYGEN or NITROUS OXIDE Do not shine directly into the eyes or directly over thyroid gland center of neck Administer only after physician consultation if patient 1 is pregnant 2 has epilepsy and 3 taking any medication that would cause a sensitivity to light such as tetracycline or acutane 4 any skin conditions that would be negatively affected by light stimulation Indoor use only Do not operate near water SPECIFICATIONS Power Switch A power OFF ON rocker switch is located on the back of the unit Operation Selection A panel push button switch START allows the operator to start the application session Session Timer and Display An internal session timer is set for the 10 minute session time at the start of the applicat
5. System 210 Berg Street Algonquin IL 60102 Toll Free 844 506 6525 www rev light com Page 6
6. ated at a 50 duty cycle e g 10 minutes operation followed by 10 minutes of non operation Expected Service Life 5 Years Physical Environmental Total Unit Weight 17 lbs Operating ambient temperature range of 10 C 50 F to 40 C 104 F Operating humidity maximum 95 RH no condensation Shipping Storage Unit Shipping Measurements Size 24 W x 24 D x 12 H Weight 24 lbs Storage temperature range of 20 C 4 F to 50 C 122 F Storage humidity maximum 95 RH no condensation Power Supply Power supply input requires 100 240VAC 50 60Hz 2 0A max IEC C14 input receptacle Use only GlobTek power supply REF GMT21089 1815 T3 REF G1200LCP Y MED Replacement contact distributor request replacement REF 62 0000150 power supply Warranty For specific warranty issues please contact your distributor Repair Units contain no user serviceable components Contains calibration devices and or calibrated circuitry Any repair would require that the device be tested for proper operation and verified that it is functioning to established specifications This involves the use of fixtures equipment and procedures that would not be field deliverable All repairs should be performed by the original equipment manufacturer where the device operation can be verified to the original manufacturing standards To arrange for repair services please contact your distributor CONTACT INFORMATION RevLight Skincare
7. ion and will turn the applicator LEDs off at the end of the application The timer is provided for the convenience of the operator and does not provide any safety related function Application LEDs Utilizes 5 high output red 625nm optically coupled emitters at 160mW each 108 narrow beam blue 420nm LED emitters at 18mW each 48 narrow beam infrared 940nm LED emitters at 20mW each 72 narrow beam red 625nm LED emitters at 20mW each The LEDs are operated in one of two modes utilizing combinations of the LEDs The Red IR mode utilizes the 5 high output red emitters plus the 72 red and 48 IR narrow beam emitters The Blue only mode utilizes the 108 narrow beam blue LEDs Effective photo power 208 cm2 application area 22 mW cm2 peak output Red IR mode 13 2 joules cm2 peak per 10 minute session Red IR mode 12 mW cm2 peak output 420 nm Blue mode 7 2 joules cm2 peak per 10 minute session Page 5 Model 1030 User Manual Photopulsation The light output is photo modulated with a weighted set of frequencies that are continuously cycled throughout the application Photomodulation Frequencies Hertz duration is seconds 73Hz 4s and 584Hz 1s Thermal Considerations This device is intended to elevate the skin temperature to 40 C 45 C 104 F 113 F when operated in Red mode Operation Rating Not suitable for continuous operation Designed to be oper
Download Pdf Manuals
Related Search