Grafiprint laminates FLOOR - grafityp selfadhesive products
Contents
1. certain period of time you can polish it Please only use the products that are specifically meant for this application The old application wax on wax off with a polishing paste is not applicable in this case Removal of the vinyl Grafiprint materials have been developed especially not to leave behind any glue residues after removing them If you wish to remove the vinyl we advise you to heat it with a heat gun Pull off the vinyl under an angle of 90 If any glue stays behind on the surface you can remove it with isopropanol Tip 4 If any glue residues stay behind this is often because the vinyl is too warm and the adhesive is too cold Just wait for a moment until the heat has reached the area between the adhesive layer and the paintwork and things will become much easier You will find the right balance between heating and removing the vinyl after some practice This GrafiManual is not to be considered as a complete product manual It is only meant as a tool to give you an idea of the possibilities and the application of the above mentioned products More detailed information about these products can be found in the product data sheets and on www grafityp com2. User Manual Floor laminates Page 1 of 2 Special applications G ra f H M anua Grafiprint FLOOR LAMINATES FLOOR and SOL on Grafiprint media Introductory remarks Floor laminates protect your prints that are applied onto the floor This allows you to make additional publicity on floors staircases etc Even though the quality of these materials would allow them to be used outdoors we strongly advise against it because the vinyl will become quite slippery when it gets wet in spite of the material s structured surface You can cut these materials on a cutting plotter You will of course have to adjust the knife pressure Slow cutting will also give a better result Grafiprint laminates FLOOR and SOL are preferably combined with Grafiprint SO2P SO5S SO6S or S110P Combinations with Grafiprint S110P S111P S112P or S113P are also possible The Preparation It goes without saying that you need to laminate your prints in a propre and dustfree space Never put printed rolls on the floor before laminating them otherwise they would attract dust particles Also make sure there is no dust or dirt on your clothes e g from sawing the panels Avoid touching the printed surface or the adhesive layer of the laminate with your fingers Laminating There are various ways to laminate a print Cold laminating can be used for most applications Warm laminating is always better to achieve a good adhesion between print and lamina
3. ed User Manual Floor laminates Page 2 of 2 The tools Felt squeegee Cutting knife Heat gun Extension cord Sufficient light Roll of tape Electric current Meter felt tip pencil The preparation Place the vinyl with its backing paper on the surface Always avoid cutting in the surface Apply some reference points where vinyle and surface meet so you easily place the vinyl at its exact position again The application of the vinyl Remove the backing paper from the vinyl Position the vinyl without folds against the reference points you applied earlier Rub the vinyl smoothly by means of the felt squeegee Make sure that the air between the object and the vinyl can always escape Tip 3 Never lay a felt squeegee on the floor Sand will creep into the squeegee and you will make scratches on the vinyl the next time you use it The Finishing Small air bubbles will disappear automatically after a certain period of time Larger air bubbles on even surfaces need to be punctured to allow the air to escape The optimal adhesive strength is reached after about three days Cleaning and Maintenance We advise you not to clean the vehicle with a high pressure cleaner Vinyl is a soft material Therefore the cleaning and maintenance shall only be executed with non scouring cleaning agents without strong solvents or corrosive ingredients If you want to give the vehicle some additional gloss after a
4. te Follow the instructions in the manual and pay attention to the safety instructions that come with your laminator Allow your print to dry for at least 24 to 48 hours or even longer depending on the amount of ink before laminating it This will guarantee an optimal adhesion between the Grafiprint print media and the Grafiprint laminate Tip 1 Remove all excess of laminate alongside the edges of the print after laminating Nothing is as annoying as small pieces of laminate that stick to your print while unrolling it The Application Tip 2 Make sure the workshop is dust free that the necessary ambient temperature has been reached and that the job can not be complicated by direct sunlight or by a heat source Also make sure the floor is completely clean as the vinyl gets statically loaded during the application process thus attracting dust very easily The vinyls are always applied dry Run a couple of tests first They can save you a lot of work Apply a test strip on the paintwork of the vehicle and on a side window and compare the result Tf the test strip sticks much harder on the paintwork than on the window or if you see lots of air bubbles this means that the vehicle has not been pre treated sufficiently Repeat the isopropanol treatment If the test strip does not stick sufficiently this means that probably a very thin layer of silicone protection has stayed behind on the vehicle The pre treatement needs to be repeat
Download Pdf Manuals
Related Search