User Manual
Contents
1. og svc ROWN 2inch Mobile thermal printer SMP M240 10 Be sure to use up the power of the battery before charge it as it can ensure the using life of the battery 1 3 Storage Precautions 1 The printer should be placed in such an environment that the temperature is between 20 C and 70C and the relative humidity is between 5 and 95 2 If the printer will be stored for a long time please be sure to take out the battery otherwise may damage the battery and printer 3 Normal thermal paper can t be kept too long if you need to keep the receipt for a long period please choose long term effective thermal paper 4 The print paper should be keep away from high temperature environment and point blank sunshine 1 4 Battery Safety Precautions Be sure to carefully read the user manual before using the product Ignore the following instructions may cause battery overheating fire explosion damage and or performance and reduced product life 1 Do not allow water sea water from entering or leaking into the battery inside If the batteries internal safety device burn when charging it it may produce any abnormal current and or voltage and cause any abnormal chemical reaction then may cause the battery overheating fire and or explosion 2 Do not use or place the battery nearby the stove or other high temperature places Excessive heat maybe damage the resin shell and or the insulation materials thereby cause s2. If more than 8 the earliest ones will be deleted from printer paring list automatically If these earliest main devices want to drive printer to print and need pairing again After pairing main devices with virtual Bluetooth interface smart phone pocket PC palm notebook can drive mobile printer SMP M240 to printer through such virtual Bluetooth interface 10 4 Operation Methods 4 1 Preparation before using 4 1 1 Li ion battery installation 1 Refer to the picture put the battery in the battery slot please pay attention to the correct insert and 2 Close the battery case 4 1 2 Paper loading Upper cover Platen Danan TA SAA J V x 7 Use two fingers to press L yy 0 this place and open the upper cover Operation methods 1 Use two fingers to press the place showed in the picture and open the upper cover 2 Put the paper into the paper case pay attention to the direction of the paper If loaded reversely it won t print 3 Pull paper out of paper case 4 Make sure paper in the center then close upper cover 8 4 4 LED indicator and Buzzer definition There are one buzzer and two LED indicators to indicate the printer status LED indicators indicate current status and buzzer indicates the changes of status Status indicator Power indicator Status Blue Red Flash quickly OFF Power on charging ON OFF
3. internal short circuit may cause excessive current and lead to the battery overheat ignite and or explosion and the adjacent metal objects necklaces hairpins etc may be overheating 9 Do not throw or heavy attack the battery If internal safety device of the batteries burn the battery charging may cause any abnormal current and or voltage and abnormal chemical reaction and lead to the battery overheat ignite and or explosion 5 1 Precautions 1 1 Safety Precautions 1 Be sure to use the specified battery and power source provided by our company Connection to an improper power source may cause fire explosion or damage to the printer 2 Don t put the battery into the fire or water don t disassemble or modify the battery don t be short circuit otherwise may result in injury or fire even explosion 3 If the printer would not be used for a long time be sure to take off the battery otherwise the battery may leak liquid which is corrosive if improper operation causes battery leak and the liquid is spattered on the skin or clothes please wash it with water if spattered in the eyes please rinse them with water thoroughly and see a doctor 4 Please do not open the paper case cover when it is printing or just when printing is over do not touch the print head with hand or body overheat may cause scald 1 2 Operation Precautions 1 Be sure not to print continuously over 1 meter otherwise may cause damage
4. to feed paper manually Printer will stop feeding when reaching max feeding distance Max feeding distance could be set by the PC software MPTTools please refer to your distributor for more technical information of MPTTools 4 2 5 Battery charging When li ion battery runs out of power blue LED indicator flash slowly and buzzer will give out warning It will power off automatically when continues printing If you want to go on please charge it Charging method Plug in socket 220V 50Hz with power adapter 1 Power off charging LED light will always indicate blue color and goes off when fully charged 2 Power on charging LED light will keep blinking in blue color and stop blinking when fully changed When charging printing is available 4 5 The installation of printer driver 1 Double click SynCrownSMPMpPrinterDriver v 1 0 0 2 exe Click Install 2 Choose the printer port and printer type you need and click OK to next step 3 Click Finish A successful installation 5 Other information 5 1 Printer technical manual control command Please refer to SMP M240 technical manual 5 2 Preprinted black mark specification If user wants to locate receipt by detecting preprinted black mark shall accord to the following specification for the black mark Otherwise it may cause printer can t recognize the black mark Printing position black mark shal
5. Battery Charging eeeeeeeeeeteetteeerteeesteesttessteesrteesstessreessrreesseeesseesss 9 4 3 Interface and printing eeeeeeeeteeteeeetteestteerteesrteesrteesrteesteesrereesreeesreeesss 10 A 3 41 Serial Interfaces eiieeii seene eaei esseri E seitsmest 10 4 3 2 Infrared ray IR amp IrDA interface eeeeeereeeerteeerteeeteesrteesrteesesseeesss 10 433 Bluetoothi sse E i EE Ea e E eE ieis 10 4 4 LED indicator and Buzzer definition eeeeeeeeeeseeeseeseeseseeseessesseeseesee 11 5 Other information s t8s0eseesonedasnsoresssacbsensssasesessastssadenstseesccesaacsesavexesateonsies 12 5 1 Printer technical manual De ee 42 5 2 Preprinted black mark specification s sssssessseeeseeeeeseeeseeeee seses 12 2 current and lead to the battery overheat burning and or explosion 6 Do not heat the battery or put the battery into fire This may melt insulation material and or damage safety devices or safety equipment then ignite electrolytic solution and cause the battery overheat burning and or explosion 7 Do not use the battery with contrary and Location In the charging process this will cause the reverse charging and may cause abnormal chemical reaction During use may appear unpredictable current exception and cause the battery overheat ignite and or explosion 8 Do not make the battery and contact with any metal Also do not carry along or store batteries with metal objects such as necklaces hair clips and so on Battery
6. Power off charging Flash slowly OFF Battery low ON OFF pai OFF OFF Power off charging Battery full OFF ON Power on Flash slowly Flash slowly Paper end OFF Flash slowly Standby Buzzer Status Once Power on Twice Power off Once Connect USB Twice USB disconnected Once Press FEED button Once Connect to power adapter Three times Power on charging Battery full Three times Enter to the parameter setting mode Four times Download the Font library Twice Battery low the printer will shut down automatically after buzzing 11 4 2 Basic Function 4 2 1 Printer on The printer is powered on by pressing the power button the power indicator is on with red color whenever the printer is on Note when the batter is almost exhausted the power indicator blinks with blue color in this case you must charge the battery by using the adaptor The method of charging the battery please refer to 3 2 5 4 2 2 Printer off The printer is off after hold down the power button for 2 seconds All the indicators are off whenever the printer is off 4 2 3 Self test The self test checks the printer s current settings status and whether the printer has any problems Hold down the FEED button while press Power button about 3 seconds the self test begins The printer is ready to receive data as soon as it completes the self test 4 2 4 Paper feeding When printer works under non blackmark mode user could use FEED button
7. eliability TPH density 100 million pulses i ESC P Satara Emulation SC POS Driver Windows 2000 XP Vista Win 7 Win 8 7 4 3 Interface and printing 4 3 1 Serial Interfaces This model of printer uses DB 9 serial interface cable one end is D model standard serial interface socket connected to host computer the other end is PS 2 socket connected to printer 4 3 2 Infrared ray IR amp IrDA interface SMP M240 can be connected to your main device through IR RAW IR and IrDA can not be available at the same time Reset the printer if it is not the model you want When printing through RAW IR and IrDA make infrared ray of main device right towards to infrared ray window of printer distance should be less than 50mm varies with main device angel should be less than 30 4 3 3 Bluetooth PDA with Bluetooth interface laptop and other information terminals can drive the mobile thermal printer SMP M240 instructions as follows 1 Power on printer 2 Main device search for outer Bluetooth devices 3 If there are some outer Bluetooth devices choose Syncrown 4 Enter password 0000 5 Finish matching In pairing mobile thermal printer SMP M240 must be turned on Note when pairing do not set many printers on otherwise it can t figure out which one succeeds in pairing Having finished pairing other main devices main devices still can pair with mobile thermal printer The max main devices of each printer are 8
8. hort circuit inside the battery then the battery may be caused overheating burning and or explosion 3 When charging use a specified charger Other conditions high temperature high pressure high current using the modified battery charger etc excluded here may result in over charging the battery and abnormal current and or voltage cause abnormal chemical reaction and may cause the battery overheat light and or explosion 4 Battery clearly marks with positive and negative When connect the battery with the charger and or printer be sure to verify the correct battery orientation Reverse insertion will cause the reverse charging and may cause abnormal chemical reaction and then may cause the battery overheat ignite and or explosion 5 Do not make the battery contact with the power outlet and or car cigarette lighter socket This may cause high pressure and excessive 4 CONTENTS 1 PRET CS eseriv sess esivsiesasatewiesnesn cesses devanaricneransvarepnonadeddaenssaderawsnenieiuaniaceiey 3 1 1 Safety Precautionses essesssseesseeeseesssssessssesssseseeeeeseseeseeeseeeneeeenees 3 1 2 Operation Precautionses s ssessessesesesseeeseesseetessseeneseensseeeseenenseeenen 3 1 3 Storage Precautionses ssesssesssseesseessseeseseseessseesssnensseensseseseeseseenen es 4 1 4 Battery Safety Precautions r ssseseseseseeeseessseessseeeesseteseseenseneneneeens 4 9 Brief triton seevasestenes coeds saessossascacoedbsasd aera dteivnadesedeect
9. l preprint at the left side of receipt Width rang gt 7mm Height 4mm lt height lt 6mm Reflection rate to IR lt 10 reflection rate to the black mark on paper gt 65 Hps Hps indicates the distance from down edge of detecting mark from beginning line Omm lt Hps lt 1mm width height 12
10. ndescondaarsencstaereens 6 2 1 Appearance verssseseseeseseessseeststenesssessssensetenssessesesenssneseseasseeeeseeneseeseseeseeny 6 DDR COGBSOMGS so sas nesonss ie va nnsattnnssetaxadagaessneanetaavadniceieanrsetireaneedanmasecaaisaiee es 6 3 Specifications s essseseseseeeseeeseeesseessseensseessseesensseensseensseeneeseenseseneaneenees 7 3 1Printing specifications eset es tee estes te teste teneeenesteneseeneneeneneeneeenees 7 3 2 Physical specifications s ses estes es teesteseseeseseeneststeneetenesteneeenneseeseennees 7 3 3 Environment Specifications sseseseseseses tess eeeeteseeeeseseeteseeneneenene es 7 3 4 Other specifications eeeeeeeeerteeetteeerteeetteeeteeerteesrttessttesstessreessreessseeesee 7 A Operation MethodS seeeeeeeeteteeerteeerteeerteerteesrteeertresrteesteesreeessreesreeessesteens 8 4 1 Preparation before USING ss sssresssessseesseseeseseeseseensseesensetensetenseeneens 8 4 1 1 Li ion battery loading sesssesesseseeseseeeseeesteeseeeneseeneseeneeeeneeneees 8 4 1 2 Paper loading sssesssesessesesssseessseessseesessetesseeeneesenssesseneeneseeteneeneees 8 AS Basie Functor iesise sieus ee ee ee 9 AO Printer omesse eesis i sratine eai Eres Eaa EEEa EE 9 ADD Printet off ee eteeriseen usteen Esse v er Ess PENES Kurse Serine KEE EEEn uses 9 423 Self testerete iinit deesseassdbesoiestinesdasdsdesetiieneids 9 4 2 4 Paper loading eeeeeeteeteeesteeeteeesteesrtteesteerreessteessseesstresteesseeesseeesseeess 9 4 2 5
11. terface 9 RS232 interface 5 Power input 10 Li ion battery cover 2 2 Accessories 2 2 1 Standard accessories Q Li ion battery Power Adapter Paper roll USB cable 2 2 2 Optional accessories Leather case Serial interface cable 6 3 Specifications Item Parameter Printing method Thermal line printing Resolution 203DPI 8dots mm Printing Printing speed 50 70mm s Valid printing width 48mm Interface IrDA Bluetooth RS232 USB Power saving Sleep mode YES Character set Font E daa Multiple code pages support UPC A UPC E EAN8 EAN13 Barcode 1D CODE39 ITF CODEBAR CODE128 symbologies CODE93 2D QR code Support bitmap printing with different density and user defined bitmap Graphics printing Max 40K for per bitmap and Max 76K for total Detection Sensors Paper out detection LED indicator Power indicator Red Status indicator Blue Power supply 12V 0 5A POWSTAUDPIY 1500mAh 7 4V Battery rechargeable Li ion battery Paper type Thermal paper Paper width 58mm Paper Paper thickness lt 0 12mm Paper roller diameter lt 40mm Paper loading Easy loading mechanism Working condition 10 C 50 C 25 80 RH Physical Storage condition 40 C 70 C 93 RH 40 C characteristics Dimension 102 5 x75x45mm Weight 197g without paper roll Optional kits RS232 data cable leather case 50km not more than 12 5 printing R
12. to the print head 2 Water or other liquid should not spill into the printer also the printer should not be appeared in the rain or else may cause printer damage 3 Please do not open the paper case cover when it is printing otherwise the printer may work improperly 4 If print with serial interface should not unplug the interface cable in the course of printing or else some printing data may be lost 5 When printin Ir or IrDA mode be sure the Ir window of the host equipment face rightly the Ir window of the printer the distance should be within the range of 50cm and the angle should be within the range of 30 6 When print with Bluetooth interface the communication distance should be within 10 meters otherwise the printer doesn t print or prints rubbish codes 7 Too high 50 C or too low 10 C temperature and too high 85 or too low 20 relative humidity both effect the print quality 8 The print paper in poor quality or stored for too long time also may reduce the print quality even damage the printer 9 Inthe black mark detecting mode the printer requires that the preprinted black mark is accordant with the black mark specifications details please refer to 4 2 otherwise the black mark can not be detected correctly e 2 Brief Introduction 2 1 Appearance 1 Power indicator Red Light 6 FEED button 2 Status indicator Blue Light 7 Power on off 3 Infrared ray IR interface 8 Top cover 4 USB RS232 in
Download Pdf Manuals
Related Search