Valor™ 7000 Series - Ohaus Corporation
Contents
1. IR Sensor front Figure 3 5 Front view of Valor 7000 Valor 7000 Series EN 7 3 2 Turning Scale On Off To turn the scale on press and hold the On Zero Off button for 1 second The scale performs a display test momentarily displays the software version and then enters the active welghing mode To turn the scale off press and hold the On Zero Off button until OFF is displayed 3 3 Weigh Mode This mode is the factory default setting 1 If needed press and hold Mode until LJE 16H Weigh is displayed 2 If required place an empty container on the pan and press Tare 3 Add sample to the pan or container The display shows the weight of the sample 3 4 Percent Mode This mode measures the weight of a sample as a percentage of a reference weight 1 If required place an empty container on the pan and press Tare 2 Press and hold Mode until PEr ent is displayed ELr rEF clear reference will then display If no reference weight exists the scale will display Put EF proceed to step 5 3 Press No to use the stored reference weight and proceed to step 6 4 Press Yes to establish a new reference Scale will now display Put r EF 5 Add the desired reference material to the pan or container Press Yes to store the reference weight The display shows 100 6 Re2. Figure 4 1 Setup for the Weigh Below Hook Valor 7000 Series EN 25 TABLE 4 2 GEO CODES Elevation in meters O0 325 650 975 1300 1625 1950 2275 2600 2925 3250 325 650 975 1300 1625 1950 2275 2600 2925 3250 3575 Elevation in feet O 1060 2130 3200 4260 5330 6400 7460 8530 9600 10660 1060 2130 3200 4260 5330 6400 7460 8530 9600 10660 GEO value ooo 546 5 4 4 3 3 2 2 1 1 0 0 3156 33 09 12 raver E 8 2 2 CO ep CI 8 9 8 8 3421 35 91 13 13 12 12 d f 10 10 9 9 8 3591 36241 14 13 13 12 12 fd 1 10 10 9 9 36941 3750 14 14 13 13 12 12 1 11 10 10 9 3750 38 58 15 14 14 13 13 12 12 11 1 10 10 38558 4005 15 15 14 14 13 13 12 12 1 1 10 4005 4112 16 15 15 14 14 13 13 12 12 11 maz 4219 16 16 15 15 14 14 13 13 12 12 11 4219 4326 17 16 16 15 15 14 14 13 13 12 12 4326 4432 17 17 16 16 15 15 14 14 13 13 12 4492 45 38 18 17 17 16 16 15 15 14 14 13 13 4598 46745 18 18 17 17 16 16 15 15 14 14 13 46545 4751 19 18 18 17 17 16 16 15 15 14 14 47551 48 58
3. 2 Valor 7000 Series Instruction Manual Valor 7000 Series EN 1 1 INTRODUCTION This manual contains installation operation and maintenance instructions for the Valor 7000 Series Please read the manual completely before using the scale 1 1 Definition of Signal Warnings and Symbols Safety notes are marked with signal words and warning symbols These show safety issues and warnings Ignoring the safety notes may lead to personal injury damage to the instrument malfunctions and false results Signal Words CAUTION for a hazardous situation with low risk resulting in damage to the device or the property or in loss of data or injuries if not avoided Note No symbol For useful information about the product Warning Symbols N Attention Symbol ISS Alternating Current 1 2 Safety Precautions Please follow these safety precautions e Verify that the AC input voltage printed on the data label matches the local AC power supply e Do not drop loads on the platform Make sure that the power cord does not pose a potential obstacle or tripping hazard e Do not position the scale in a way that makes it difficult to pull the power plug Use only approved accessories and peripherals Operate the scale only under ambient conditions specified in these instructions Disconnect the scale from the power supply when cleaning e Do not operate the scale in hazardous or unstable environments e Do not immerse the sc
4. U CU NN MN EN es A OC in 00 010 VALOR 7000 Menu Mode dede Print Function Units Mode Back Figure 3 1 Valor 7000 Front Control Panel with LCD Display On Zero Off Yes Function Mode Back M Menu Exit Tare TABLE 3 1 when on Sets display to zero when off Turns scale on Long Press when on Turns the scale off Short Press in Menu Selects accepts displayed setting Short Press See Interface Manual for operation description Long Press Toggles through active weighing units Short Press in Menu Toggles through available settings Short Press Selects function setting Long Press Selects active Mode Short Press in Menu returns to previous settings Short Press Accumulates the weight and displays the accumulated information at O load Long Press Enters User Menu Short Press in Menu Quickly exit User Menu Short Press 2 Short Press Enter clear a tare value Clears the accumulation when the accumulation information is displayed The IR Sensor can be programmed to act as touchless buttons See section 4 3 for the available settings Notes Short Press Press less than 1 seconds Long Press Press and hold for more than 2 seconds 7 Press and hold the Off button until OFF is displayed then release the button Valor 7000 Series EN 5 1 16 2 15 3 14 4 13 5 12 6 7 8 9 10 11 Figure 3 2 LCD Display TABLE 3 2 Item Description
5. 1 ltem Description o 1 NETsymbol 9 Calibration MenuModesymbol 6 Pointersymbols 14 Kilogram gram symbols 8 Accumulation symbol 16 Scale symbol not used The colored LED indicators on the left side of the control panel are used in Check mode section 3 5 and will light up according to the following rules O Red Loads gt Upper limit O Green Loads 2 Lower limit and lt Upper limit Yellow Loads lt Lower limit 1KA2 EIE Pcst LI Chee de E ZU C O LI LI LL LJ S wv 2 LED Indicators IR Sensor back Figure 3 3 Valor 7000 back LCD Display EN 6 Valor 7000 Series Power Input Weigh Below Access RS232 and Option Interface Port below cover Lock Switch IR Sensor front Figure 3 4 Below view of Valor 7000 IR Sensors The Valor 7000 is equipped with two IR sensors one at the front See figure 3 5 and one at the rear see figure 3 3 The front and rear sensors perform the same function The sensors can be activated by a hand or other object that is placed at a specified distance in front of the sensor locations The sensor activation distance will vary based on the reflective nature of the object If unwanted activations occur due to unique situations the sensor can be turned off See section 4 3 Setup Menu for available settings
6. 7752 80756 30 29 29 28 28 27 27 26 26 25 25 80 56 85745 30 30 29 29 28 28 27 27 26 26 25 85 45 9000 31 30 30 29 29 28 28 27 27 26 26 EN 26 Valor 7000 Series 5 LEGAL FOR TRADE When the scale is used in trade or a legally controlled application it must be set up verified and sealed in accordance with local weights and measures regulations lt is the responsibility of the purchaser to ensure that all pertinent legal requirements are met 5 1 Capacity Label A label showing the capacity and readability of the scale must be installed near each display If the Capacity Labels were installed prior to delivery no further action is needed If the Capacity Labels were not installed they have been placed in the packaging material Affix the labels above the displays as shown in Figure 5 1 Note The Capacity Labels will be destroyed upon removal so only attempt to install them once Capacity Label ZD CHCIHCICI Cheese OOO Cs v v v v Ww Ww bo z Menu Mode VALOR 7 On Zero Print Function M Off Units Mode Menu T T T Yes No Back Exit Figure 5 1 Front and rear display Capacity Label locations A O V OHAUS 5 2 Settings Before verification and sealing perform the following steps 1 Verify that the menu settings meet the local weights and measures regulation
7. 1 800 526 0659 between 8 00 AM and 5 00 PM EST An OHAUS product service specialist will be available to provide assistance Outside the USA please visit our web site www ohaus com to locate the OHAUS office nearest you 6 4 Accessories Ethernet Interface Kit 30037447 ond RS232 Interface Kit 30037448 USB Interface Kit 30037449 Weighing Below Hook 30037450 In Use Cover 30007445 In User Cover 10 pcs set 30007469 Printer Contact Ohaus Communication Cables Contact Ohaus EN 30 Valor 7000 Series 7 TECHNICAL DATA The technical data is valid under the following ambient conditions Indoor use only Operating temperature 10 C to 40 C Relative humidity 20 to 85 relative humidity non condensing Altitude Up to 2000 m Power AC power 100 240V 50 60 Hz internal rechargeable sealed lead acid battery Current rating 0 5A Mains supply voltage fluctuations up to 10 of the nominal voltage Installation category Il Pollution degree 2 7 1 Specifications TABLE 7 1 MODEL V71P1502T V71P3T V71P6T V71P15T V71P30T 1 5 kg x 0 00005 kg 3 kg x 0 0001 kg 6 kg x 0 0002 kg 15 kg x 0 0005 kg 30 kg x 0 001 kg Capacity x Readability 1500 g x 0 05 g 3000 g x 0 1 g 6000 g x 0 2 g 15000 g x 0 5g 30000 0 X 1 d Max xd non approved 3 Ib x 0 0001 Ib 6 Ib x 0 0002 Ib 15 Ib x 0 0005 Ib 30 Ib x 0 001 Ib 60 Ib x 0 002 Ib 48 oz x 0 002 oz 96 oz x 0 005 oz 240 oz x 0 01 oz 480 oz x 0 02 oz 960 oz x 0 05 oz Resolution E 1 5 kg x 0 0005
8. 19 19 18 18 17 17 16 16 15 15 14 48558 5006 20 19 19 18 18 17 17 16 16 15 15 5006 51713 20 20 19 19 18 18 17 17 16 16 15 5113 5222 21 20 20 19 19 18 18 17 17 16 16 5222 5331 21 21 20 20 19 19 18 18 17 17 16 5391 544 22 21 21 20 20 19 19 18 18 17 17 54 41 55552 22 22 21 21 20 20 19 19 18 18 17 5552 5704 23 22 22 21 21 20 20 19 19 18 18 5704 5837 23 23 22 22 21 21 20 20 19 19 18 5817 59 32 24 23 23 22 22 21 21 20 20 19 19 5982 60 24 24 23 23 22 22 21 21 20 20 19 60 49 62 90 25 24 24 23 23 22 22 21 21 20 20 62 90 63 30 25 25 24 24 23 23 22 22 21 21 20 63 30 64755 26 25 25 24 24 23 23 22 22 21 21 64355 66 24 26 26 25 25 24 24 23 23 22 22 21 6624 6757 27 26 26 25 25 24 24 23 23 22 2 67757 69 35 27 27 26 26 25 25 24 24 23 23 22 6935 71 21 28 27 27 26 26 25 25 24 24 23 23 7121 73316 28 28 27 27 26 26 25 25 24 24 23 736 7524 29 28 28 27 27 26 26 25 25 24 24 75724 77 52 29 29 28 28 27 27 26 26 25 25 24
9. Connect AC power plug to power plug to the input jack on the proper AC supply the back of scale 2 5 1 Battery Power The scale can be used on AC power immediately Allow the battery to charge for 12 hours before using the scale on battery power The Scale will automatically switch to battery operation if there is a power failure or the power cord is removed With AC power the scale is constantly charging so the battery charge indicator see item 11 in figure 3 2 will remain lit The scale can be operated during charging and the battery is protected against overcharging For maximum operating time the battery should be charged at room temperature During battery operation the battery symbol indicates the battery charge level remaining The indicator will automatically turn off when the batteries are fully charged TABLE 2 1 41 to 70 Remaining 71 to 100 Remaining Notes When battery symbol blinks fast approximately 30 minutes working time is left When to bRE is displayed the scale will shut off Charging the scale must be performed in a dry environment CAUTION Battery is to be replaced only by an authorized Ohaus service dealer Risk of explosion can occur if the rechargeable battery is replaced with the wrong type or if it is not properly connected Dispose of the lead acid battery according to local laws and regulations EN 4 3 OPERATION 3 1 Controls Valor 7000 Series ZE OHAUS V
10. E Each field is followed by a single delimiting space ASCII 32 Definitions Weight If negative Unit Up to 9 characters right justified at immediate left of most significant character Up to 5 characters left justified If the Unit in the Print Content menu was set to OFF the unit will be removed in the weight string and replaced by spaces EN 34 Valor 7000 Series Stability character is printed if not stable If weight is stable neither or following Space is printed G N NET printed if weight is net weight G or nothing printed if weight is a gross weight Terminating Character s terminating character s printed depending on FEED menu setting 7 6 Compliance Compliance to the following standards is indicated by the corresponding mark on the product Mark Standard oo This product conforms to the EMC Directive 2004 108 EC the Low Voltage Directive 2006 95 EC and the Non Automatic Weighing Instrument Directive 2009 23 EC The Declaration of Conformity is available online at europe ohaus com europe en home support compliance aspx AS NZS CISPR 11 CAN CSA C22 2 No 61010 1 12 UL Std No 61010 1 3 edition MC173467 NSF ANSI 169 2009 go Wire v Z USDA lt t NSF ANSI 3 A 14159 1 2010 m9 Ati pi Important notice for verified weighing instrument M Weighing Instruments verified at the place of manufacture bear one of the preceding marks on the
11. EN 19 Content COREA Define the content of the printed data See section 7 4 for sample printouts Result Set the status OFF disabled ON lt the displayed reading is printed Gross Set the status OFF disabled ON the gross weight is printed Net Set the status OFF disabled ON the net weight is printed Tare Set the status OFF disabled ON the Tare weight is printed Header Set the status OFF disabled ON the Header is printed Note See section 7 3 1 for how to enter Header line Footer Set the status OFF disabled ON the Footer is printed Note See section 7 3 1 for how to enter Footer line Mode Set the status OFF disabled ON the Mode is printed Unit Set the status OFF disabled ON the Unit is printed Info Set the status OFF disabled ON the reference information is printed ex check limits Accu Set the status OFF disabled RESULT the Accumulation result is printed ALL all the Accumulation data is printed EN 20 Valor 7000 Series Layout LAYGUE Set the format of the data output to a printer or computer Format Set the printing format MULTI a multi line single column style printout is generated SINGLE a single line printout is generated Feed Set the paper feed LINE move a paper up one line after printing 4LF move a paper up four lines after printing FORM a form feed is appended to the printout Data Transfer dRtA tr Output weighing
12. For jurisdictions that use the audit trail sealing method the local weights and measures official or authorized service agent must record the current configuration and calibration event counter values at the time of sealing These values will be compared to values found during a future inspection Note A change to an event counter value is equivalent to breaking a physical seal The audit trail uses two event counters to record changes to configuration and calibration settings e The configuration event counter CFG will index by 1 when exiting the menu if one or more of the following menu settings are changed Zero Range Stable Range Auto Zero Tracking AZT Units kg g oz lb or Ib oz or Stable Only e The calibration event counter CAL will index by 1 when exiting the menu if a Span Calibration or GEO setting change is made Note that the counter only indexes once even if several settings are changed The event counters can be viewed by pressing and holding the MENU button While the button is held the display will show MENU followed by Audit alibration alibration alibration alibration The scale then returns to normal operation LI Calibration EN 28 Valor 7000 Series 6 MAINTENANCE 6 1 Cleaning The housing may be cleaned with a cloth dampened with a mild detergent if necessary Do not use solvents chemicals alcohol ammonia or abrasives to clean the housing or control panel 6 2 Troubleshooting
13. noreset YES reset Baud Rate bRud Set the baud rate 300 300 bps 600 600 bps 1200 1200 bps 2400 2400 bps 4800 4800 bps 9600 9600 bps 19200 19200 bps Parity PAr E set the data bits and parity 7 EVEN 7 data bits even parity ODD 7 data bits odd parity 7 NONE 7 data bits no parity 8 NONE lt B data bits no parity Stop bit SEGP Set the number of stop bits 1 1 stop bits 2 2 stop bits Handshake H ShAFE Set the flow control method Hardware handshaking is only available for COM1 menu NONE no handshaking ON OFF XON XOFF software handshaking EN 22 Alternate command RL E CP 1 Define command character for the Print Tare and Zero commands Print Set the alternate command character for Print A to Z Tare Set the alternate command character for Tare A to Z Zero Set the alternate command character for Zero A to Z End COM1 End COM End Advance to the next menu or return to the top of the current menu 4 9 Lock Menu Valor 7000 Series The Lock menu is a software controlled option which can lock menu settings to prevent tampering Default settings are bold Reset no yes Lock Cal off on Lock Setup off on Lock Read off on Lock Mode off on Lock Unit off on Lock Print off on Lock COM off on End Menu Lock Exit menu Reset rESEE Reset the Lock menu to factory defaults NO no reset YES reset Lock Cal L CAL Set
14. results directly to a PC application OFF disabled ON enabled Windows XP Setup 1 Click Start Menu in Windows XP and click Settings gt open Control Panel 2 Double click Accessibility Options in Control Panel Select the General tab Check Use Serial Keys and click the Settings button Select the Serial Port set the Baud rate to 9600 and click OK Close the Control Panel 7 Run Excel to open one blank sheet Focus the cursor on one item At this time if scale sends data to the PC through the RS232 port the data will be placed into the cell and the cursor will automatically move to the next vertical cell Oo C amp L Notes For Windows 7 setup contact Ohaus If the weighing value is a negative number set the target cell in TEXT format Otherwise Excel will not distinguish it as a negative number Please do not use this function during continuous printing End Print End Advance to the next menu or return to the top of the current menu Valor 7000 Series 4 8 COM1 Menu Enter this menu to define communication parameters Default settings are bold Reset no yes Baud Rate 300 9600 19200 Parity 7 even 7 odd 7 none 8 none Stop bit 1 2 Handshake none On Off Alternate command Print A P Z Tare A T Z Zero A Z End COM Exit menu Note The COM2 menu is only displayed if a second interface is installed Reset rESEE Reset the COM menu to factory defaults NO
15. D E EA a a E a Oe te Oe 11 11 kg NET OVER Result line 12 34 kg G Gross value line 11 11 kg NET Net value line 1 23 kg T Tare value line MODE CHECKWEIGH UNDER TARGET 1 00 kg OVER TARGET 2 00 kg Mode line Information line Information line TEARS AE A AO LOPE O AE POPE E ACA AO OE E 7 5 Output Format Weight string print format Term Char s Comment If Printx Content Result is ON If Printx gt Content gt Gross is ON and a tare value is entered If Printx Content Net is ON and a tare value is entered If Printx Content gt Tare is ON and a tare value is entered If Printx Content gt Accu is All If Printx Content gt Accu is All If Printx Content gt Accu is All If Printx Content gt Accu is All Comment If Printx gt Content gt Result is ON If Printx Content Gross is ON and a tare value is entered If Printx Content gt Net is ON and a tare value is entered If Printx Content gt Tare is ON and a tare value is entered If Printx Content Application Mode is ON If Printx Content Info is ON Comment If Printx Content Result is ON UNDER ACCEPT OVER If Printx Content Gross is ON and a tare value is entered If Printx Content gt Net is ON and a tare value is entered If Printx Content gt Tare is ON and a tare value is entered If Printx Content Application Mode is ON If Printx Content Info is ON If Printx Content Info is ON Eum ngu e um E PEE pu
16. F always off ON always on AUTO turns on when a button is pressed or the displayed weight changes Auto off R OFF oet the automatic shut off functionality OFF disabled 1 powers off after 1 minute of no activity 5 powers off after 5 minute of no activity 10 powers off after 10 minute of no activity Valor 7000 Series EN 17 End Readout End Advance to the next menu or return to the top of the current menu 4 5 Mode Menu This sub menu activates modes so they will be available for use with the Mode button Weigh mode is always active Default settings are bold Reset no yes Weigh off on Percent off on Check off weigh percnt End Mode Exit menu Reset ESEt Reset the Mode menu to factory defaults NO not reset YES reset Weigh LJE 15H Set the status OFF disabled ON enabled Percent PEr CNE Set the status OFF disabled ON enabled Check CHEC Set the sub mode OFF disabled WEIGH weight mode PERCNT percent mode End Mode End Advance to the next menu or return to the top of the current menu Note Available modes vary by model and local regulations 4 6 Unit Menu This sub menu activates units so they will be accessible with the Units button The units in the menu must be turned on to be active Note Available units vary by model and local regulations EN 18 Valor 7000 Series 4 7 Printi Menu Enter this menu to set printing parameters Defa
17. Notes When active unit is g or kg the calibrating unit will be in kg When active unit is Ib oz or Ib oz the calibrating unit will be in Ib For linearity calibration the calibration Mass is fixed Mid point is always half of full capacity Span Perform Linearity Perform Geographic Adjustment Set 0 12 31 End Calibration Exit menu Bold always represents factory default value Span SPAR Initiates a span calibration procedure zero and span Lin t f Initiates a linearity calibration procedure zero mid point and span GEO GEO Geographical Adjustment Factor GEO is used to adjust the calibration based on the current location Settings from O to 31 are available with 12 being the default Refer to table 4 2 to determine the GEO factor that corresponds to your location End Cal End Advance to the next menu or return to the top of the current menu EN 14 Valor 7000 Series 4 3 Setup Menu Enter this menu to set scale parameters Default settings are bold Reset no yes Power On Unit auto kg g lb oz Ib oz Zero Range 2 10 Auto Tare off on on acc Beeper Signal off accept under over under over Beeper Key off on IR Func disp zero func tare print IR Adjust off low high Accumulation off auto manual End Setup Exit menu Reset ESEt Reset the Setup menu to factory defaults NO not reset YES reset Power on unit Pour Uhl Set the unit of measure disp
18. Table 6 1 lists common problems and possible causes and remedies lf the problem persists contact OHAUS or your authorized dealer TABLE 6 1 Symptom Possible Cause Cannot turnon No power to scale Verify connections and voltage aaa Improper calibration Perform calibration y Unstable environment Move scale to suitable location Cannot calibrate LFT locked See chapter 5 for more information Cannot access mode Mode not enabled Enter menu and enable mode Cannot access unit Unit not enabled Enter menu and enable unit Connect the scale to AC power and Battery icon flashing Low Battery error charge the battery Weight reading exceeds Power On Zero Weight reading below Power On Zero Err BB Displayoverflow Weight exceeds 6 digits Bus Displayed during tare setting zero setting printing Action not allowed Function not executed m m m m Calibration value outside allowed limits Move the scale to suitable location Use correct calibration weight reference weight Increase reference weight Le lind di d Only accumulate gross or net weights HO HC C es only works in LFT Battery fails to charge Have battery replaced by Ohaus fully aaa L authorized service dealer Valor 7000 Series EN 29 6 3 Service Information If the troubleshooting section does not resolve or describe your problem contact your authorized OHAUS service agent For service assistance or technical support in the United otates call toll free
19. ale in water or other liquids e Do not place the scale upside down on the platform e Only use weights within the scale s capacity as specified in these instructions e Service should be performed only by authorized personnel 2 INSTALLATION 2 1 Package Contents e Scale e Sub platform e Instruction Manual CD e In use Cover e Pan e Power Cord e Warranty Card EN 2 Valor 7000 Series 2 2 Installing Components Install the sub platform and metal pan as shown below Press to lock the sub platform into place Figure 2 1 Install the sub platform and metal pan 2 3 Selecting the Location Use the scale on a firm steady surface Avoid locations with excessive air current vibrations heat sources or rapid temperature changes Allow sufficient space around the scale 2 4 Leveling the Equipment The Valor Series has a level indicator as a reminder that the scale should be leveled for accurate weighing To level the scale adjust the feet so the bubble is centered in the circle Be sure the equipment is level each time its location is changed Level Indicator YES NO n Adjustable feet Figure 2 2 Level indicator Valor 7000 Series EN 3 2 5 Connecting Power AC power is used to power the scale when battery power is not needed First connect the AC power cord supplied to the power input jack then connect the AC plug to an electrical outlet Figure 2 3A Connect the AC Figure 2 3B
20. alrededor del mundo Avec des bureaux dans le monde entier Weltweite Geshaftsstellen Con uffici in tutto il mondo www ohaus com 3 0 0 4 8 2 3 9 P N 30048239D 2014 OHAUS Corporation all rights reserved todos los derechos reservados tous droits r serv s Alle Rechte vorbehalten tutti i diritti riservati Printed in China Impreso en la China Imprim en Chine Gedruckt in China Stampato in Cina
21. ccept the low limit value SEE H j will be displayed 8 Repeat the same procedure to accept or edit the high value Valor 7000 Series EN 9 9 If required place an empty container on the pan and press Tare 10 Place sample material on the pan or in the container If the sample weight is under the target percentage range the yellow LED will light If the sample is within the target percentage range the green LED will light If the sample is over the target percentage range the red LED will light Note Press Function to view the low and high check limits Positive Check Positive check is used to determine when the material added to the scale is within the target range In this case the UNDER and OVER limits must be positive values The OVER limit must be greater than the UNDER limit Add material to the scale until it is within the ACCEPT green range Negative Check Negative check is used to determine when the material removed from the scale is within the target range In this case the UNDER and OVER limits are both negative values The UNDER limit must be greater than the OVER limit for example UNDER 10 OVER 15 Place the item to be weighed on the scale and press Tare Remove a portion of the item until it is within the ACCEPT range Zero Check Zero check is used when comparing subsequent samples to an initial reference sample In this case the UNDER limit must be a negative value and the OVER limit must be a p
22. e Place sample material on the pan or in the container If the sample weight is under the target weight range the yellow LED will light If the sample is within the target weight range the green LED will light If the sample is over the target weight range the red LED will light Note Press Function to view the low and high check limits 3 5 2 Check Percent oet Checkweigh to Percent in the Mode menu Use this mode to compare the percentage of items to a target percent range 1 Press and hold Mode until CHEC Check is displayed Ct e c EF clear reference will then display If no reference weight exists the scale will display Puk rEF proceed to step 4 Press No to use the stored reference weight and proceed to step 5 Press Yes to establish a new reference Scale will now display Puk r EF 4 Add the desired reference material to the pan or container Press Yes to store the reference weight 5 The scale will display Ct t 9 clear Check limits Press No to use the stored check limits and proceed to step 9 Press Yes to establish new check limits The scale will then display SEE La Press Yes to view the Low limit value Press Yes to accept or No to edit the Low limit value The stored value then displays with the first digit highlighted 500 000 2e Repeatedly press No until the desired number appears Press Yes to accept and highlight the next digit Repeat until all the digits are correct Press Yes to a
23. e scale is equipped with an RS232 interface COM1 located under the Options Cover Connecting the scale to a computer enables you to operate the scale from the computer as well as receive data such as displayed weight 7 3 1 Interface Commands Communicate to the scale using the command characters listed in Table 7 2 below TABLE 7 2 OS Turn off Stable Only menu item and allow unstable print 1S Turn on Stable Only menu item and only print stable print Interval Print x Print Interval 1 3600 sec OP turns auto print OFF Same as pressing Zero Key same as pressing Tare Key Download Tare value in grams positive values only Sending OT clears tare if allowed Print current unit g kg Ib oz Ib oz Set scale to unit x 129 2 kg 3 lb 4 0z 5 lb 0z Enter Header line where x line number 1 to 5 text header text up to 24 alohanumeric characters 4 4 Enter Footer line where x line number 1 to 2 text rear text up to 24 F x text alohanumeric characters Global reset to reset all menu settings to the original factory defaults EscR iD Escape key R Key H x text 7 3 2 Connections for RS232 The 9 pin female subminiature D connector COM1 is provided for interfacing to other devices The pin connections are as follows Active pins PIN 2 TXD PIN 3 RXD PIN 5 Ground 0000 606 Figure 7 2 RS232 Pins Valor 7000 Series EN 33 7 4 Printouts The
24. ent facility Please dispose of this product in accordance with local regulations at the collecting point specified for electrical and electronic equipment If you have any questions please contact the responsible authority or the distributor from which you purchased this device Should this device be passed on to other parties for private or professional use the content of this regulation must also be related Disposal instructions in Europe are available online at europe ohaus com europe en home support weee aspx Thank you for your contribution to environmental protection FCC Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Industry Canada Note This Class B digital apparatus complies with Canadian ICES 003 ISO 9001 Registration In 1994 OHAUS Corporation USA was awarded a certificate of registration to ISO 9001 by Bureau Veri
25. following sample print outs are generated by the Print button P Command or alternate print command The content of the printout is defined in the Print Content menu item A maximum of 24 characters can be printed on each line Weigh Mode Printout Description 11 11 kg NET Result line 12 34 kg G Gross value line 11 11 kg NET Net value line 1 23 kg T Tare value line MODE WEIGH lt no line printed gt Mode line Information line EEA IM e E PEINE IO AA ES E AA AAN Comment If Printx gt Content gt Result is ON If Printx Content Gross is ON and a tare value is entered If Printx Content gt Net is ON and a tare value is entered If Printx Content gt Tare is ON and a tare value is entered If Printx Content Application Mode is ON If Printx Content Info is ON Weigh Mode with Accumulation Printout Description 11 11 kg NET Result line 12 34 kg G Gross value line 11 11 kg NET Net value line 1 23 kg T Tare value line N 4 Accumulation line TOTAL 49 85 kg MIN 11 11 kg MAX 14 85 kg LOL AER SP ues MA AA LOR AO LU Ie AO Accumulation line Accumulation line Accumulation line Percent Mode Printout Description ici botas ee aa am 100 NET Result line 12 34 kg G Gross value line 11 11 kg NET Net value line 1 23 kg Tare value line MODE PERCENT REF WGT 11 11 kg OL LPL EL PE E ML HE AAA oe a Check Weighing Mode Printout Description Mode line Information line b E D A O Ws E
26. hes HI around 100 mm 4 inches Accumulation ACCUNN Set the accumulation functionality OFF accumulation disabled AUTO automatic accumulation MAN manual accumulation End Setup End Advance to the next menu or return to the top of the current menu EN 16 Valor 7000 Series 4 4 Readout Menu Enter this menu to set user preferences Default settings are bold Reset no yes Stable Range 0 5 1 2 5 Filter low medium high Automatic Zero Tracking off 0 5 1 3 Light off on auto Auto Off off 1 5 10 End Headout Exit menu Reset ESEt Reset the Read menu to factory defaults NO not reset YES reset Stable Range SEAbLE oet the amount the reading can vary while the stability symbol remains on 0 5d 0 5 scale division 1d 1 scale division 2d 2 scale division 5d 5 scale division Filter F LEE oet the amount of signal filtering LOW less stability faster stabilization time MED normal stability stabilization time HI greater stability slower stabilization time AZT Ret oet the automatic zero tracking functionality OFF disabled 0 5d the display will maintain zero until a change of 0 5 divisions per second has been exceeded 1d the display will maintain zero until a change of 1 divisions per second has been exceeded 3d the display will maintain zero until a change of 3 divisions per second has been exceeded Light L GHE Sets backlight functionality OF
27. kg 3 kg x 0 001 kg 6 kg x 0 002 kg 15 kg x 0 005 kg 30 kg x 0 01 kg Capacity x Readability 1500 g x 0 5 g 3000gx19g 6000gx2g 15000 0 X 5 d 30000 0 x 109g Max x e approved 3 lb x 0 001 Ib 6 Ib x 0 002 Ib 15 Ib x 0 005 Ib 30 Ib x 0 01 Ib 60 Ib x 0 02 Ib 48 oz x 0 02 oz 96 oz x 0 05 oz 240 oz x 0 1 oz 480 oz x 0 2 oz 960 oz x 0 5 oz Approved Resolution 1 3000 Repeatability 0 0001 kg 0 0002 kg 0 0005 kg 0 001 kg 0 002 kg 0 0001 kg 0 0002 kg 0 0005 kg 0 001 kg 0 002 kg LFT OFF g kg lb oz Ib oz LFT ON g kg lb oz EC and OIML Approved models g kg To capacity by subtraction Stabilization Time afe Overload Capacity 150 of capacity LCD with white LED backlight 6 digit 7 segment 28 mm 1 1 inches digit height LCD with white LED backlight 6 digit 7 segment 18 5 mm 0 7 inches digit height Keyboard 5 mechanical buttons Application Modes Weighing Check Weighing Check Percent Percent Weighing Accumulation Battery Operating Time 210 hours with backlight turned off at 20 C ABS plastic housing with 304 stainless steel platform Front Display Back Display 225 x 300 mm 8 9 x 11 8 in hipping Dimensions 397 x 447 x 195 mm 15 6 x 17 6 x 7 7 in 4 2 kg 9 3 lb 5 45 kg 12 lb Valor 7000 Series EN 31 7 2 Drawings 311 mm 12 2 in tz 327 mm 12 9 in Figure 7 1 Dimensions EN 32 Valor 7000 Series 7 3 Communication Th
28. layed at startup AUTO last unit in use when turned off kg kilograms g grams lb pounds OZ ounces lb oz pound ounces Zero Range 2E 0 Set the percentage of scale capacity that may be zeroed 2 zero up to 2 percent of capacity 10 zero up to 10 percent of capacity Auto Tare R ER E set the automatic tare functionality OFF Automatic Tare is disabled ON the first stable gross weight is tared ON ACC stable gross loads within the accept limits are tared in Check weighing mode Beeper Signal bP S iG set how the beeper responds in Check Weighing mode OFF the beeper is disabled ACCEPT the beeper will sound when the weight is within the Accept range UNDER the beeper will sound when the weight is below the Under setting OVER the beeper will sound when the weight is above the Over setting OVER the beeper will sound when the weight is below the Under setting or above the UNDER Over seiting Beeper Key bP FEY Set whether the beeper sounds when a button is pressed OFF no sound ON sound Valor 7000 Series EN 15 IR Func A F Define the sensor function Both sensors will have the same function DISP turn on backlight ZERO scale performs zero operation FUNC scale performs function operation TARE scale performs tare operation PRINI scale performs print operation IR Adjust ir Adu Set the distance at which the sensor will respond OFF disabled LOW around 50 mm 2 inc
29. locked at 1d Auto Zero Tracking setting is locked at 0 5d Unit menu is locked at the current setting Stable Only is locked On Auto Print Continuous is disabled Lb oz is locked at Off IR Sensor and Filter menus may be locked at the current settings if required by local weights and measures regulations EN 12 Valor 7000 Series Summary of button navigation functions in menu mode Yes Allows entry into the displayed menu Accepts the displayed setting and advances to the next item No Skips by the displayed menu Rejects the displayed setting or menu item and advances to the next available item Back Moves backwards through the upper and middle level menus Backs out of a list of selectable items to the previous middle level menu Exit Exits from menu directly to the active weighing mode For menu items with numeric settings such as Capacity the current setting is displayed with all digits flashing Press the No button to begin editing The first digit is displayed flashing Press the No button to increment the digit or press the Yes buiton to accept the digit and move to the next digit Repeat this process for all digits Press the Yes button when the last digit has been set The new setting is displayed with all digits flashing Press the Yes button to accept the setting or press the No button to resume editing This method also applies to setting Checkweigh under and over targets For End menu items p
30. or Trade is ON the display must return to 0 gross Otherwise the gt pointer will continue flashing Gross loads and net loads cannot be added to the same total If the first load is a gross weight future loads must also be gross weights If the first load is a net weight future loads must also be net weights Example If required place an empty container on the pan and press Tare Step i Put the weight 0 04 kg on the pan and press M key The 2 pointer indicator will keep flashing until the weight is removed Step li Remove the weight from the pan Put another weight 0 03 kg and press M key Step iii Remove the weight from the pan Step iv Press M key to display the statistical information Step v If required follow section 3 6 2 to clear the accumulation data 4 MENU SETTINGS The User Menu allows the customizing of scale settings Note Additional Sub Menus may be available if Interface Options are installed See Interface User Manual for the additional setting information 4 1 Menu Navigation Men CAL SELUP rEAd MOdE gt User Menu Unit Print COM1 LOCKk End Reset Stable A Print Contnt Layout Data Tr End Notes Some modes units may not be available in all models When LEGAL FOR TRADE is set to ON LET Switch in locked position the menu settings are affected as follows Calibration C A L menu is not accessible Zero Range is locked at 2 Stable Range setting is
31. ositive value Place the reference item on the scale and press Tare Remove the reference sample and place the item to be compared on the scale to determine if it is within the ACCEPT range EN 10 Valor 7000 Series 3 6 Accumulation and Statistics The Accumulation feature enables manual or automatic totalizing of displayed values Statistical data total accumulated min and max weight or 96 and total number of weighments is stored in memory for review and printing Accumulation works together with each application mode except Dynamic 3 6 1 Accumulating Displayed Values With ACCUMULATE set to MANUAL place the item on the scale and press the M key to add the weight to accumulation data The gt pointer will keep flashing until the weight is removed With ACCUMULATE set to AUTO place the item on the scale The displayed value is accumulated automatically The gt pointer will keep flashing until the weight is removed 3 6 2 Viewing and Clearing Statistical Data When the pan is cleared press the M key to display the statistical information To clear the accumulation data press the Tare key while the statistical information is displayed The display shows CLr ACC Press the Yes key to clear the stored data and return to current mode Notes The item must be removed from the pan before the next item can be accumulated Only stable weights are stored to accumulation data Changing the mode will clear the accumulation data When Legal f
32. packing label and the green M metrology sticker on the descriptive data plate They may be put into service immediately Weighing Instruments to be verified in two stages have no green M metrology on the descriptive data plate and bear one of the preceding identification marks on the packing label The second stage of the initial verification must be carried out by an authorized and certified service organization established within the European Community or by the National Notified Body The first stage of the initial verification has been carried out at the manufacturers work lt comprises all tests according to the adopted European standard EN 45501 1992 paragraph 8 2 2 If national regulations limit the validity period of the verification the user of the weighing instrument must strictly observe the re verification period and inform the respective weights and measures authorities Valor 7000 Series EN 35 Disposal In conformance with the European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE this device may not be disposed of in domestic waste This also applies to countries outside the EU per their specific requirements The Batteries Directive 2006 66 EC introduces new requirements from september 2008 on removability of batteries from waste equipment in EU Member States To comply with this Directive this device has been designed for safe removal of the batteries at end of life by a waste treatm
33. place the reference material with the sample material The display shows the percentage of the sample compared to reference weight 7 To clear the stored reference press and hold Mode until PErent is displayed Press Yes when Ct r c EF is displayed Note Press Function to view the current reference weight EN 8 Valor 7000 Series 3 5 Check Mode Use this mode to compare the Weight or Percent of items to a target range The scale supports positive negative and zero check weighing Refer to section 4 5 to set the desired Check sub mode 3 5 1 Check Weighing Set Checkweigh to Weight in the Mode menu Use this mode to compare the weight of items to a target weight range 1 Press and hold Mode until CHEC Check is displayed ft t 9 clear check limits will then display Press No to use the stored check limits and proceed to step 5 Press Yes to establish new check limits The scale will then display SEE La Press Yes to view the Low limit value Press Yes to accept or No to edit the Low limit value The stored value then displays with the first digit highlighted 00 000 kg Repeatedly press No until the desired number appears Press Yes to accept and highlight the next digit Repeat until all the digits are correct Press Yes to accept the low limit value SEE H q will be displayed Repeat the same procedure to accept or edit the high value If required place an empty container on the pan and press Tar
34. ressing the Yes button advances to the next menu while pressing the No button returns to the top of the current menu Valor 7000 Series EN 13 4 2 Cal Menu Enter this menu to perform calibrations Initial Calibration When the scale is operated for the first time a span calibration is recommended to ensure accurate weighing results Before performing the calibration be sure to have the appropriate calibration weights as listed in table 4 1 Ensure that the LFT switch calibration lock is set to unlock position See figure 5 1 Or adjust the GEO setting according to your location see table 4 2 Procedure Press and hold Menu until PENU Menu is displayed When the button is released the display will show E A L Press Yes to accept SPAR will then be shown Press Yes to begin the span calibration O kg will be displayed Press Yes to accept will be displayed while zero reading is stored Next the display shows the calibration weight value Place the specified calibration mass on the pan Press Yes to accept the weight or No to select an alternate weight will be displayed while the reading is stored The display will show donE if the calibration was successful The scale returns to the previous application mode and is ready for use TABLE 4 1 Required Span Calibration Mass sold separately 1500g 1 5kg 3lb 15000g 15kg 30lb 30009 3kg 6lb 300009 30kg 60lb 60009 6kg 15lb
35. s 2 Perform a calibration as explained in Section 4 2 3 Set the switch to Locked See figure 5 2 The Menu Lock switch limits changes to the Cal Setup Readout Unit and Print menus The switch in type approved models may set some scale settings as required by the approval agency The switch may be secured using paper or wire seals Note When LEGAL FOR TRADE is set to ON LFT Switch in locked position the menu settings are affected as follows Calibration R L menu is not accessible Zero Range is locked at 296 otable Range setting is locked at 1d Auto Zero Tracking setting is locked at 0 5d Unit menu is locked at the current setting Stable Only is locked On Auto Print Continuous is disabled Lb oz is locked at Off IR Sensor and Filter menus may be locked at the current settings if required by local weights and measures regulations 5 3 Verification and Sealing The local weights and measures official or authorized service agent must perform the verification procedure 5 3 1 Physical Seals For jurisdictions that use the physical sealing method the local weights and measures official or authorized service agent must apply a security seal to prevent tampering with the settings Refer to the illustration below for sealing methods Valor 7000 Series EN 27 Lock Switch Paper Seal Wire Seal Unlocked Locked with Paper Seal Locked with Wire Seal Figure 5 1 Sealing 5 3 2 Audit Trail Seal USA and Canada only
36. the status OFF Calibration menu is not locked ON Calibration menu is locked Lock Setup t SEEuP Set the status OFF Setup menu is not locked ON Setup menu is locked Lock Read L ERd Set the status OFF Readout menu is not locked ON Readout menu is locked Valor 7000 Series Lock Mode t P od Set the status OFF Mode menu is not locked ON Mode menu is locked Lock Unit L Un E Set the status OFF Unit menu is not locked ON Unit menu is locked Lock Print L Pr ne Set the status OFF Print menu is not locked ON Print menu is locked Lock COM t C amp P7 Set the status OFF COM menu is not locked ON COM menu is locked End Lock End Advance to the next menu or return to the top of the current menu 4 10 End Menu EN 23 Press No to advance to the Calibration menu Press Yes to exit the menu and return to the current application mode EN 24 Valor 7000 Series 4 11 Additional Features To use this feature remove AC power from the scale and remove the protective cover for the weigh below opening Install a suitable hook into the access hole at the bottom of the scale as shown refer to section 6 4 for optional hook Do not over tighten tighten finger tight Mount the scale onto an appropriate assembly that allows free working space below the hook See figure 4 1 Note Never allow the scale to rest directly on the hook Weigh Below Hook Access
37. tus Quality International BVQI confirming that the OHAUS quality management system is compliant with the ISO 9001 standard s requirements On June 21 2012 OHAUS Corporation USA was re registered to the ISO 9001 2008 standard EN 36 Valor 7000 Series LIMITED WARRANTY OHAUS products are warranted against defects in materials and workmanship from the date of delivery through the duration of the warranty period During the warranty period OHAUS will repair or at its option replace any component s that proves to be defective at no charge provided that the product is returned freight prepaid to OHAUS This warranty does not apply if the product has been damaged by accident or misuse exposed to radioactive or corrosive materials has foreign material penetrating to the inside of the product or as a result of service or modification by other than OHAUS In lieu of a properly returned warranty registration card the warranty period shall begin on the date of shipment to the authorized dealer No other express or implied warranty is given by OHAUS Corporation OHAUS Corporation shall not be liable for any consequential damages As warranty legislation differs from state to state and country to country please contact OHAUS or your local OHAUS dealer for further details OHAUS OHAUS Corporation 7 Campus Drive Suite 310 Parsippany NJ 07054 USA Tel 1 973 377 9000 Fax 1 973 944 7177 With offices worldwide Con oficinas
38. ult settings are bold Note The Print2 menu is only displayed if a second interface is installed Reset no yes Stable Only off on Auto Print off on stable interval continuous accept Content Result gt off on Gross gt off on Net gt off on Tare gt off on Header gt off on Footer gt off on Mode gt off on Unit gt off on Info gt off on Accu gt off result all Layout Format gt S M Feed gt Line 4 Lines form Data Transfer off on End Print Exit menu Reset rESEE Reset the Print menu to factory defaults NO no reset YES reset Stable Only SEAbLE Set the printing criteria OFF values are printed immediately ON Values are only printed when the stability criteria are met Auto Print A Pr int Set the automatic printing functionality OFF disabled ON STAB printing occurs each time the stability criteria are met INTER printing occurs at the defined interval CONT printing occurs continuously ACCEPT printing occurs each time the display is within the Checkweigh accept range and stability criteria are met When ON STAB is selected set the condition for printing where LOAD printing occurs when the load is stable and greater than zero LOAD ZR printing occurs when any load is stable and equal to or greater than zero When INTER is selected set the Print Interval 1 to 3600 seconds Valor 7000 Series
Download Pdf Manuals
Related Search