User Manual Analog Pager 1. Introduction 2. Turning
Contents
1. Press SELECT 1 until the correct hour is reached then press OK 2 to adjust the minutes Press SELECT 1 until the correct minute value is selected and then press OK 2 to save the time 4 8 Envelope The envelope icon allows users to replay previously deleted messages 5 Receiving an alert gt lt A red LED REC on the display indicates that a mes REC ed 7 Sage is being recorded Messages are recorded for 30 seconds unless an alternate configuration has been chosen To interrupt the recording press and hold OK 2 After receiving an alert call press the right OK 2 button once to acknowledge the call Once the call is acknowledged the pager is in idle again Alternate configurations include 15 seconds 30 seconds 60 seconds two minutes or four minute recording increments Maxi mum recording capacity is 4 minutes 6 Muting an alert quickly Muting an alert quickly for quiet environments is easy Sim ply press the SELECT 1 button twice to mute the incoming message The message will be recorded and may be replay ed at a later more convenient time To quickly stop the tone alert and still listen to the incoming message press the SELECT 1 button once The tone alert will stop however the incoming message will still be audib le 7 Replaying messages only for units with stored voice To replay messages press the OK 2 button once and the most recent message will be played To ski2. User Manual Analog Pager ni i j O j B a ee SWISSPHONE 1 Introduction Congratulations on purchasing your new Swissphone analog pager This instruction manual will guide you through the features and operations of your new paging unit While there is a wide range of configuration options possible using the Swissphone programming software this manual will descri be the standard features and programming of your pager For the latest version of this manual please visit our website at www swissphone com e Do not use this product in explosive areas e The warranty expires if you try to open the device or remove any label 2 Turning the pager on off Turn the pager on by pressing and holding both the SELECT 1 and the OK 2 button simultaneously until you hear a loud beep Once you hear a loud beep your pager is turned on Turn the pager off by pressing and holding both the SELECT 1 and the OK 2 buttons for approximately four seconds After a four second countdown with audible clicks the pager will power down 3 Controls and Display Corner Buttons The analog receiver is operated by two buttons The left but ton is called SELECT 1 and allows the user to cycle through the various icons on the display The right button is called OK 2 and allows the user to confirm the selection made with the SELECT 1 button along with acknowledge and replay messages Display When idle the display show
3. ery type NbAtt for dry cell and NAc cu for rechargeable bat teries If needed you can now toggle between the selections with the left hand button To apply the current selection please press the right hand button 9 Customer service Please contact us by phone 41 44 786 77 70 or by e mail at info swissphone com for further assistance Swissphone Wireless AG Falmisstrasse 21 8833 Samstagern switzerland This device complies with Part 15 of the FCC Ru les Operation is subject to the condition that this device does not cause harmful interference This Swissphone pager meets the requirements of the European Guideline R amp TTE 99 05 EG Radio Equipment and Telecommunications Terminal Equipment Please ask for a declaration of con formity at info swissphone com Swissphone Wireless AG Specifications subject to change CH 03 14 v4 Art Nr 0343138
4. n increased risk of missing calls during ac tivated scanning mode Single channel pagers are not available with scanning 4 6 Volume al To change the volume press the SELECT 1 button until the volume icon begins to blink then press the OK 2 button several times to change the volume level When the desired volume level is reached confirm the selection with SELECT 1 All of the Icons above can be placed in the order of your choice through programming by your dealer You may prefer i e the volume icon to be the first selection in the menu Additional functions al Usually these functions are in the secondary menu which may be accessed by holding the SELECT 1 button for approximately two seconds Profiles Channels Press SELECT 1 and cycle through the icons until the active profile is blinking Press OK 2 until the desired profile is flashing and confirm the selection by pressing SELECT 1 il The profiles channels are usually located in the first position of the secondary menu to access them easily To change the profile channel in that instance access the secondary menu by holding the SELECT 1 button for approximately two se conds Next press the OK 2 button to switch to the desired profile and confirm the selection by pressing SELECT 1 4 7 Clock Cycle Clock Cycle through the menu using the SELECT 1 button until the clock icon begins to blink Next confirm the selection by pressing OK 2
5. p to the next mes sage press the OK 2 button again or cancel the playback by pressing the SELECT 1 button To delete a message press the OK 2 button twice It is possible to delete all messages with the exception of the most recent message recorded to the pager Deleted messages may be played by activating the envelope and pressing OK 2 8 Replacing the battery Two types of batteries are compatible with the Swissphone analog pager e AAnickel metal hydride NiMH a k a rechargeable battery e AA alkaline dry cell a k a non rechargeable battery To open the battery compartment use a coin to press down on the indented space between the belt clip and the pager housing at the back of the unit Once the clip is loose remove the battery compartment cover from the right side Please note If a non rechargeable battery is inserted in the pager the unit will charge for no more than ten minutes once placed in the charging cradle preven ting any permanent battery acid related damage to the pager Non rechargeable batteries should not be left in the pager when charging although this protec tive feature is enabled on the charger After inserting any battery the battery type must be chosen by the user To make the user aware that an action is nee ded the following symbols will be shown alternating in the Pw BARE Accu Dry cell battery Rechargeable Accumulator Pressing the right hand button will pre select the active ba t
6. s the current operation mode battery level volume level and active profile or time of the day if no profiles are in use SELECT 1 OK 2 Loud Mini alert alert P of A A XK E C Piros yooog gt Z Vibrate Monitor Scanner Battery charge indicator OOOO REC i Y X lO is Signal 4 Message Volume strength alert manager Set time 4 Operation of the Pager The Swissphone programming software allows users to di vide icons between two menus the primary menu and the secondary menu To access the secondary menu press and hold the left SELECT 1 button for approximately two seconds Previously hidden icons appear Press the SELECT 1 button to navigate through the icons and press the right OK 2 button to confirm the selection 4 1 Loud alert c1 Pager vibrates beeps and plays incoming messages 4 2 Mini alert Pager vibrates and plays incoming messages For some configurations the pager will also beep in ad dition to vibrating and playing the incoming message 4 3 Vibrate BK Pager only vibrates 4 4 Monitor Pager will monitor the frequency specified in the l active profile 4 5 Scanning on off Pager will scan all channels that have been program med on the scan list To turn scanning ON OFF press the SELECT 1 but ton until the scan icon begins to flash then press the OK 2 button to switch scanning on off Confirm your selection by pressing SELECT 1 Please note that there is a
Download Pdf Manuals
Related Search