User Guide PCX-IP LW
Contents
1. Note Under 64 bit operating systems and for most current ASIO applications e g Cubase Nuendo etc you have the choice between a 32 bit version and a 64 bit version when installing them The 64 bit package of HR Runtime installs botha 10 PCX IP LW881e PCX IP LW1221e User s manual 32 bit ASIO driver and a 64 bit ASIO driver To use the ASIO driver on your PCX sound card the option PCM only has to be enabled from the Digigram control panel CPL To access this control panel go to Start Programs lt Digigram gt Digigram Control Center To launch the ASIO control panel go to Start Programs lt Digigram gt Digigram ASIO HR Settings Unregistered ASIO PCX IP LW881 S N x It allows to Selected board POXIPLWESI S N e set modify the size of ASIO buffers latency adjustment select the number of bits per sample 16 24 32 select the LTC frame rate select the I Os to be used by the application s 960 samples Latency 20 0 ms enable disable the hardware monitoring control deh ET enable disable the multi client mode When enabled several 9 Rescan ASIO divers Current board settings Buffer size T applications can access different channels of the card but Sample size LTC frame rate Select aolivaied Kal one channel cannot be used by several applications Qleb O3b For more information on this ASIO control panel to refer to its online help 9 24 bit Enable dir2. Required CPU power and memory mainly depend on the operating system and on the audio application used Software requirements To use your card under Windows please install the driver from the HR Runtime package version 1 74 or higher This package includes a Digigram np driver enabling OEM applications to best capitalize on the on board features MPEG mixing time scaling cross fades e aWDM DirectSound driver 32 bits or 64 bits according to the OS e a Wave driver 32 bits installation optional e an ASIO driver 32 bits and 64 bits installation optional PCK IP LW881e PCK IP LW1221e User s manual HARDWARE INSTALLATION Due to the reduced length of the PCI EXPRESS bus connector and the resulting lack of mechanical stability we strongly advise against transporting the PCle amp card s installed in a computer unless its chassis or case provides a dedicated support to keep the card securely in place in order to avoid physical damage The card has to be installed in the computer prior to installing its driver Installing the card Gently plug the card in a free PCI slot and press it down to position it firmly Tighten the screw Interrupt and memory address Hardware interrupt and addresses are automatically set up at start up by the PCI PnP BIOS PCX IP LW881e PCK IP LW1221e User s manual SOFTWARE INSTALLATION The installation of the driver package requires administrator rights on your computer Please
3. 5A 0A 0 1A 0A 3 3V 5V 12V 12V Operating temp humidity 0 C 50 C 5 95 non condensing Storage temp humidity 5 C 70 C 0 95 non condensing Inputs Outputs a jan Livewire Livewire output mono channels mono channels Programmable input output digital from 110 dB 18 dB from 110 dB 18 dB pem RE General Purpose Inputs amp General Purpose Inputs amp Outputs Sampling frequency Sampling frequencies available 48 kHz Connectors Development environments amp supported operating systems Other APIs DirectSound DirectKS PCM ASIO PCM Wave PCM amp MPEG Layer I amp II OS supported Windows 8 Windows 7 Windows XP Windows Server 2003 Windows Se rver 2008 APPENDICES 1 Windows XP and Server 2003 only for Windows Vista a Wave driver is available on request 19 User s manual Schematic diagrams PCX IP L W881e Livewire core d stereo destinations PCI Express interface PCI Expreaa bus GPIOs connector pinout PCX IP LW1221e Livewire Network Livewire core Eius 1 stereo amp sberea Gestination Sources PCI Express interface PCX IP LW881e PCK IP LW1221e User s manual Livewire Network E GPI 5 GPO The pinout of the GPIOs on the Sub D 15 pin connector of the PCX card is identical to the GPIO connector used in Axia nodes Customer Port Connector 15 pin D Interface OUT COM RETURN N C OUT
4. OUT OUT OUT OUT int D ov GND WE 8 SOURCE fo ee o 4 2 ooo o o o o Oo 9 0 09 0 0 0 0 IN IN IN IN IN IN 5 o 4 3 2 1 COM PWR SOURCE 20
5. receiving 8 Livewire mono outputs PCX IP 1221e features 2 mono recording devices treceiving 2 Livewire mono outputs 16 PCX IP LW881e PCK IP LW1221e User s manual To configure the Livewire Destinations click on Destinations The following page is displayed By digigram DIGIGRAM PCX VX IP LIVEWIRE E Jigigrar Home Sources Destinations GPIO Meters QoS System DIGIGRAM PCX VX IP LIVEWIRE Destinations Name Channel Home Sources Destinations GPIO Meters QoS System RecorderIn 80 lt Player Out PCX V gt Cr Destinations 2 DST2 204 lt SRC4 LVAES gt 3 DST3 205 lt SRC S LVAES gt cS yee des Ehe Ime 4 DST4 206 lt SRC 6 LVAES gt 1 RecorderIn 80 Player Out PCX V gt gt n 2 DST2 204 SRC4QLvAES 3 DST3 205 lt SRCS LVAES gt v E Player Out PCX VXOOOOAF 4 DST4 206 lt SRC 6 LVAES gt 7 SRC 2 PCX VXO000AF SRC 3 PCX VXOOO0AF SRC 4 PCX VXOOO0AF From this page you can e Give a name to each local output to the Livewire node Name 16 printable characters max This can typically be the name given to a channel of a recording application running on the PCX IP card ex PCX IP Rec1 e Select one of the available Livewire channels to be extracted and assign to the corresponding PCX IP input e Set the Type for each selected livewire channel From source To source Configuration of GPlOs BJioiogcanm Home Sourc
6. the Diagnostics tab to display the installed card s Digigram Drivers General Information Diagnostics HR Runtime Virtual PCX configuration D i amp PCXIP play sine all channels stop If the card is not displayed e Make sure that during the HR runtime installation the Driver for the HR boards has been selected in the Select components window Open the Windows Device Manager from Control Panel System The card should be listed in Sound or Sound video and games controllers If it is listed with no warning symbol the card is well recognized by the system In case there is a warning symbol make sure that the card is correctly inserted in the PCI slot and screwed on the PC chassis e f necessary uninstall the HR runtime package as described in this manual and re install it If the card is displayed e Right click on the icon of the card e Select Diagnostics and Play Sine This plays in loop a sine signal on all the output channels of the card You can also select Play file to play in loop a file of your choice PCM only If the playback is correct the card is correctly installed and works To stop the playback right click on the card icon and select Stop Activities The DirectSound devices associated to the card are displayed from the Windows Control Panel Sound e Select tab Audio Default device Playback device Recording device Available DirectSo
7. visit the Digigram web site at www digigram com for the most recent driver In case you run a specific application developed or installed by a Digigram Partner this application might require the use of a specific driver version In this case make sure that the updated driver has been approved by your supplier The following procedure installs the Digigram Hardware Settings control panel This application allows the configuration of the hardware resources of Digigram cards for all audio applications The DHS allows for instance to adjust input and output digital gains and direct monitoring of inputs on ouputs With the inputs and outputs are controlled through the DHS application the controls available through the DirectSound control panel get invalid Volume control for input Volume control for output Standard installation Shut down your computer and insert your PCX card Restart your computer Click on Cancel if the Found New Hardware Wizard appears Double click on the HR Runtime driver package icon to launch the driver installation igigram untime v01 74 e it InstallShie izai 1 1 1 1 3B Digigrom n Runtime OE c OO EE n A welcome message is displayed click Next to continue Welcome to the InstallShield Wizard for Digigram HR Runtime v01 74 e 008 64 bit The InstallShield R Wizard will install Digigram HR Runtime v01 74 e 008 64 bit on your computer To continue dick Next WARNING This program is
8. 000 Hz Global controls 4 Link input faders 4 Link monitoring faders Link output faders Mute monitoring Mute outputs Oul Out2 4 W Digital gain Out3 Out4 P outs 7 0 48 107 0 107 0 1070 107 0 2E 107 10 3 00 sinl Right 00 sinj 1079 2 10 1079 7 Oda 006 O0 dBfs O dBfs 0 0 dBfs 0 2 Qo Lr mi 0 i 4 T PCX IP ae WB POXIP LWESI SN For more detailed information on how to use this control panel please refer to its on line help 15 PCX IP LW881e PCX IP LW1221e User s manual CONFIGURATION OF LIVEWIRE PARAMETERS To be able to configure the Livewire parameters from the WEB pages of the PCX card it is necessary to connect a NIC card of the computer to the Livewire network The PCX card default IP address is 192 168 0 100 Enter this IP address in your WEB browser address bar A username is required to access the WEB pages Username user No password The following page is displayed Bdigigram Livewire Sources Configure source parameters names channel numbers streaming format Livewire Destinations Configure destinations names channel numbers Livewire GPIO ports Configure General Purpose Input and Output ports configuration and state monitoring DIGIGRAM PCX VX IP LIVEWIRE Meters Monitor audio levels Livewire Network Livewire Clock Mastership settings Quality of Service Settings 802 1p priority and VLAN tagging DSCP Class of Service System Paramete
9. IP LW881e Wave PCX P LW1221e Wave PCX IP LW881e Wave PCX IP LW1221e Wave PCX IP LW881e Wave PCX IP LW1221e Wave PCX IP LW881e 5 1 Wave PCX IP LW1221e Wave PCX IP LW881e 7 1 Wave PCX IP LW1221e Wave PCX IP LW881e 5 142 Wave PCX IP LW1221e 5 1 Wave PCX IP LW1221e 7 1 Wave PCX IP LW1221e 5 1 2 Wave PCX IP LW1221e 7 142 Wave PCX IP LW881e Wave PCX IP LW881e Wave PCX IP LW881e Wave PCX IP LW881e Wave PCX IP LW881e 5 1 Wave PCX IP LW881e 7 1 Wave PCX IP LW881e 5 1 2 Wave PCX IP LW1221e Wave When opening the Digigram Wave Mixer application only one vu meter is displayed on the selected channel mixer Options Mixer 7 wawe In If the ASIO driver has been installed the card is visible from the ASIO control panel and from any ASIO application To launch the ASIO control panel go to Start Programs lt Digigram gt Digigram ASIO HR Settings Unregistered ASIO PCX IP LW881 S N Selected board PCXIP L w881 S N v it Open Digigram Hardware Settings application Rescan ASIO drivers Current board settings Buffer size S60 samples Latency 20 0 ms 192 4896 Sample size LTC frame rate O16bt 32ba Select activated ID ai Enable direct monitoring control Enable multi chent mode 13 PCX IP LW881e PCK IP LW1221e User s manual PCX IP LW881e PCX IP LW1221e User s manual THE DHS CONTROL PANEL Digigram Hardwar
10. PCX IP LW881e PCX IP LW1221e User s manual PCK IP LW881e PCK IP LW1221e Professional Multichannel Sound Cards with Livewire connectivity User s manual Version 1 00 April 2013 PCX IP LW881e PCK IP LW1221e User s manual For technical support please contact your system supplier Bdigigram Digigram S A Parc de Pr Milliet 38330 Montbonnot FRANCE Tel 33 0 4 76 52 55 01 Fax 33 0 4 76 52 53 07 E mail info digigram com Digigram Asia Pte Ltd 60 Albert Street 19 110G Albert Complex Singapore 189969 Singapore Tel 65 6291 2234 Fax 65 6291 3433 E mail info_asia digigram com Table of Contents INFORMATION FOR THE USER IMPORTANT NOTICE FEATURES PCX IP LW881 main hardware features PCX IP LW1221 main hardware features Main software features REQUIREMENTS Supported operating systems Minimum hardware requirements Software requirements HARDWARE INSTALLATION Installing the card Interrupt and memory address SOFTWARE INSTALLATION Standard installation X Topology installation ASIO driver configuration Wave driver configuration Removing the driver HOW TO CHECK THE INSTALLATION THE DHS CONTROL PANEL CONFIGURATION OF LIVEWIRE PARAMETERS Configuration of sources Configuration of destinations Configuration of GPIOs Vu meters Qos oystem parameters PCX IP LW881e PCK IP LW1221e User s manual PCX IP LW881e PCK IP LW1221e User s manual SPECIFICATIONS Configu
11. ansmitted through the Livewire network e 48 kHz sampling frequency Several cards can be plugged in one PC Main software features e Real time simultaneous record and playback in PCM 8 16 and 24 bits as well as in MPEG Audio Layer Layer II and Layer III Float IEEE754 conversion supported with 24 bit fixed point dynamic range e When using the Digigram np SDK real time mixing of several PCM and MPEG audio streams per output channel direct monitoring level adjustment panning cross fades punch in punch out scrubbing time stretching pitch shifting 3 band parametric equalizer Maximizer format and frequency conversions e Low latency WDM DirectSound Wave and ASIO drivers Under DirectSound and ASIO the cards operate in PCM mode only nevertheless an application can integrate coders decoders on the host PC Under Wave HR boards can operate in both PCM and MPEG layer 1 and layer 2 MPEG Layer III play only on DSP MPEG Layer III recording on the host computer is available through Digigram s PC Codec using the np SDK PCK IP LW881e PCK IP LW1221e User s manual REQUIREMENTS Supported operating systems PCX Livewire cards run under the following operating systems e 32 bit OS Windows XP Windows Server 2003 Windows Vista Windows Server 2008 Windows 7 Windows 8 e 64 bit OS Windows Server 2008 Windows 7 Windows 8 Minimum hardware requirements One PCI EXPRESS PCle slot per card x1 x4 x8 x16
12. card securely in place in order to avoid physical damage IMPORTANT NOTICE This card has been tested and found to comply with the following standards e International CISPR22 Class B e Europe EMC 89 336 CEE 1992 specifications e United States FCC Rules Part 15 Class B digital device In order to guarantee compliance with the above standards in an installation the following must be done e the provided cable must not be modified e additional cables used must have their respective shield connected to each extremity PCK IP LW881e PCK IP LW1221e User s manual FEATURES PCX IP LW881e and PCX IP LW1221e are sound cards for use with Axia Livewire systems with PCI EXPRESS PCle bus interface They are in PCI EXPRESS x1 format and can thus be plugged into any PCIe slot x1 x4 x8 x16 PCX IP LW881 main hardware features e 1 RJ 45 Ethernet port allowing for extraction of up to 8 mono channels from the Livewire network and insertion of up to 8 mono channels in the Livewire network e 1 Sub D 9 pin connector for 5 physical GPI 5 physical GPO transmitted through the Livewire network e 48 kHz sampling frequency Several cards can be plugged in one PC PCX IP LW1221 main hardware features e 1 RJ 45 Ethernet port allowing for extraction of up to 2 mono channels from the Livewire network and insertion of up to 12 mono channels in the Livewire network e 1 Sub D 9 pin connector for 5 physical GPI 5 physical GPO tr
13. e Settings DHS is an application allowing to configure the hardware resources of Digigram cards for all audio applications using them The parameters of an resource being managed by the DHS application can not be modified from another applications To enable an audio application to modify a Digigram card resource this resource must not be managed by the DHS Note As soon as a resource of a card is managed by the DHS the clock selection of this card must be defined in the DHS Iff Startup Digigram hardware settings Eick File View Help Clock Selection Inl In 2 b a i b a Internal Y Current clock status Signal detected at 48000 Hz Global controls PH Link input faders BH Link monitoring faders 4 Link output faders Mute monitoring Mute outputs ut5 w6 P Out7 Outs P 0 107 0 1070 0 s 0 H Oo 0 0 4 i in F PCK IP LW881 SN The DHS allows to e adjust digital gains of input and output signals e mute unmute input and output signals e Select the input monitored on an output zero latency hardware monitoring e Set the monitoring gains a Startup Digigram hardware settings File View Help Clock il mn I Source ai Audio over IP A310 no Selection d n d 6 H a YE 5 Digital gain We E d amp ns x udio over Left 0 0 e Right 00 0 dBfs 0 0 dBfs O dBfs 0 0 dBfs Current clock status Signal detected at 48
14. ect monitoring control F Enable multi ckent mode Wave driver configuration In the case the software application exclusively manages PCM audio through the Wave MME interface the latency of the Wave driver can be optimized by enabling the option PCM only in the Digigram control panel CPL To access this control panel go to Start Programs lt Digigram gt Digigram Control Center gt General Information Diagnostics HA Runtime Virtual PEX configuration For detailed information on how to use the Digigram control panel please refer to its online help Help button PCX IP LW881e PCX IP LW1221e User s manual Removing the driver Open the Windows Control Panel and double click on the Add Remove Software icon or Programs and Features icon depending on the Windows flavour e Select Digigram HR Runtime and Change Remove e Select Remove in the HR Runtime window e Follow the instructions to finish to remove the driver HOW TO CHECK THE INSTALLATION Once the card and the driver have been installed according to the procedure described in this manual you can check that the PCX card is properly installed and works fine as follows e From lt Start gt Programs lt Digigram gt select lt Digigram Control Center e Select the General Information tab In the Modules Information window you can see the HR Runtime modules that have been installed and their versions e Select
15. es Destinations GPIO Meters QoS System DIGIGRAM PCX VX IP LIVEWIRE GPIO Configuration Port 1 Inputs BRS Outputs IB I IL UN 12345 Name Channel l TestGPI 80 Player Out PCX VXOO00AF gt Apply Vu_meters This page displays the vu meters of the signals available on the Livewire sources typically audio coming from software players and destinations typically Livewire channels to be recorded by software recorders Click on Meters to display the vu meters page B digigram Home Sources Destinations GPIO Meters QoS System DIGIGRAM PCX VX IP LIVEWIRE dBFS Sources aBFS Destinations 0 0 co Eabb ba baba ba Eae baadbarbarlaala co pube baba aba dba aa barbarae laa MT MINH to la A 17 PCX IP LW881e PCK IP LW1221e User s manual Qos In most of the cases the parameters of the QoS page should not be changed In case you need to modify them you may refer to documents available from Axia WEB site BD digigram Home Sources Destinations GPIO Meters QoS System DIGIGRAM PCX VX IP LIVEWIRE Synchronization Livewire Clock Livewire clock master priority Livewire clock mode Live Audio Clock Streams 802 1Q tagging 802 1Q VLAN ID 802 1p priority DSCP Class of Service Standard Audio Streams Receive buffer size ms default 100 WWW 15 100 802 1Q tagging 802 1Q VLAN ID 802 1p prio
16. protected by copyright law and international treaties ae d Coe pec ngs a EE The License Agreement window appears read it and click on ae accept the terms in the license agreement to approve it DIGIGRAM SOFTWARE LICENSE AGREEMENT PLEASE READ THESE TERMS CAREFULLY BEFORE DOWNLOADING INSTALLING OR USING OUR SOFTWARE Your use of Digigram software means that you accept these terms and conditions If you do not agree with these terms and conditions then Digigram is not willing to license the software to you Licensee and you should not use the software By installing downloading ae eee E mre get eq pM I accept the terms in the license agreement Print Ido not accept the terms in the license agreement InstallShield ss cera we o Do the same in the next License agreement window for Virtual PCX and PC Codec Please read the following license agreement carefully A dig Or om Legal Notice VIRTUAL PCX and PC CODEC LEGAL NOTICE PLEASE READ THESE TERMS CAREFULLY BEFORE DOWNLOADING INSTALLING OR USING VIRTUAL PCX AND OR PC CODEC Please also refer to the DIGIGRAM SOFTWARE LICENSE AGREEMENT Both DIGIGRAM SOFTWARE LICENSE AGREEMENT and VIRTUAL PCX and PC CODEC LEGAL NOTICE shall be construed as complementary and in no case either license shall replace the other I accept the terms in the license agreement Print Ido not accept the terms in the license agreement In
17. quipment into an outlet on a circuit different from that of the receiver consult the dealer or an experienced audio television technician Note Connecting this device to peripheral devices that do not comply with CLASS B requirements or using an unshielded peripheral data cable could also result in harmful interference to radio or television reception The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment To ensure that the use of this product does not contribute to interference it is necessary to use shielded I O cables Warning Electrostatic discharge ESD can damage several components on the board To avoid such damage in handling the board take the following precautions Bring the device and everything that contacts it to ground potential by providing a conductive surface and discharge paths As a minimum observe these precautions e Disconnect all power and signal sources e Place the device on a grounded conductive work surface e Ground yourself via a grounding wrist strap or by holding a grounded object e Ground any tool that will contact the device Due to the reduced length of the PCI EXPRESS bus connector and the resulting lack of mechanical stability we strongly advise against transporting the PCIe card s installed in a computer unless its chassis or case provides a dedicated support to keep the
18. ration Inputs Outputs Sampling frequency Connectors Development environments amp supported operating systems APPENDICES schematic diagrams GPIOs connector pinout PCK IP LW881e PCK IP LW1221e User s manual INFORMATION FOR THE USER This device complies with part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a CLASS B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions contained in this data sheet may cause harmful interference to radio and television communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and the receiver connect the e
19. rity DSCP Class of Service System parameters The System page allows setting the network parameters of the PCX IP card These parameters are the usual parameters of a network interface like e Host name used to identify the PCX IP card on the network e Network address IP address of the PCX IP card on the network There must be no other node with the same IP address e Netmask mask to identify the sub network the nodes belongs to e BD digigram Home Sources Destinations GPIO Meters QoS System DIGIGRAM PCX VX IP LIVEWIRE IP settings Host name POSVRGGOOAE III 1 12 characters letters numbers hyphen Network address 192 168 0000 Netmask 255 255 255 0 Gateway 0 0 0 0 NTP server DIGIC takes effect after reset Timezone UTERO takes effect after reset Syslog server IP address BEGG Syslog severity level filter Mamm Hsmin o User password New password 5 8 characters letters and numbers Retype new password BEI verify Firmware version Hardware revision PCX VX IP LIVEWIRE e Bank 0 ver 1 0 2f build mar nov 27 10 35 18 CET 2012 Bank 1 empty update Choisissez un fichier Warning System will reboot after changing current bank 18 PCK IP LW881e PCK IP LW1221e SPECIFICATIONS Configuration S PCX IP LW881e PCX IP LW12121e PCI Express PCle x1 x2 x4 x8 x16 compatible me emma Power requirements 2
20. rs IP network settings IP network settings Software update and maintenance Configuration of sources Configuring Livewire sources is necessary to assign the playback devices of the PCX IP to Livewire inputs PCX IP 881e features 8 mono playback devices to be injected to 8 Livewire mono inputs PCX IP 1221e features 12 mono playback devices to be injected to 12 Livewire mono inputs To configure the Livewire sources click on Livewire Sources The following page is displayed B digigram Home Sources Destinations GPIO Meters QoS System DIGIGRAM PCX VX IP LIVEWIRE Sources Source Name Channel Shareable Stream Mode 1 PIEYENGG SN Kaf 2 ni WENN wS 3src3 03s N E 4 I Show source allocation status From this page you can e Give a name to each local input to the Livewire node Source Name 16 printable characters max This can typically be the name given to a channel of a playback application running on the PCX IP card ex PCX IP Player 1 e Assign a livewire channel to each source Channel The channel number must be unique and between 1 and 32767 e Set parameters for each source Shareable Stream Mode Select Live Stereo for streams where low latency is required and select Standard Stereo otherwise Configuration of destinations Configuring Livewire Destinations is necessary to assign the recording devices of the PCX IP to the Livewire outputs PCX IP 881e features 8 mono recording devices
21. s item is not selectable under Windows XP see X Topology installation Asio driver installed by default Wave MME driver not installed by default VX devices visible by default to be selected in case the np based application is not designed to detect the VX card the use of this option is specified by your software application provider Click on Next once you have made your selection of items to be installed In the Window Ready to Install the Program click on Install to start copying the files In case the User Account Control window prompts you to authorize the driver installation click on OK Driver files are then installed on the computer In case the Digital Signature Not Found message appears because a non Microsoft software is about to be installed click on Continue gt Click Finish to complete the driver installation InstallShield Wizard Completed BD digigram The InstallShield Wizard has successfully installed Digigram HR Runtime v01 74 e 008 64 bit Click Finish to exit the wizard X Topology installation Under Windows XP and Windows Server 2003 it is possible to install the drivers without the DHS so that controls like digital levels and monitoring are accessible from the DirectSound controls The driver package must then be installed as follows MsiExec exe abcd msi X_TOPOLOGY 1 where abcd msi is to be replaced by the name of the driver package ASIO driver configuration
22. stallShield Cem Jo ens Ga Custom Setup Select the program features you want installe Click on an icon in the list below to change how a feature is installed Feature Description HR boards PCX882HR VX882HR VX881HR xu This feature requires your hard drive It has x iy 4 subfeatures scien d The subfeatures eak e 8042KB o your hard driv Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to i wizard Installing Digigram HR Runtime v01 74 e 008 64 bit The program features you selected are being installed Bdigigram Please wait while the InstallShield Wiza deletes adi ia ntime v01 74e 008 64 bit This may take sever Status PCX IP LW881e PCX IP LW1221e User s manual In the Custom Setup window the Drivers for the HR boards that can be installed are listed The WDM DirectSound driver and the Digigram np driver are automatically installed Items that can be optionally installed are e Digigram Hardware Settings panel DHS installed by default The DHS control panel allows for adjusting digital level for input ouptut channels and monitoring parameters These settings cannot be controlled through DirectSound controls If the DHS is not installed these settings are accessible for the DirectSound controls Thi
23. und devices that can be selected from a DirectSound application are DirectSound playback devices DirectSound recording devices 12 OUT 1 2 Digigram PCX IP LW881e OUT 3 4 Digigram PCX IP LW881e OUT 5 6 Digigram PCX IP LW881e OUT 7 8 Digigram PCX IP LW881e OUT 5 1 Digigram PCX IP LW881 OUT 7 1 Digigram PCX IP LW881 OUT 1 2 Digigram PCX IP LW12216 OUT 3 4 Digigram PCX IP LW1221e OUT 5 6 Digigram PCX IP LW12216 OUT 7 8 Digigram PCX IP LW1221e OUT 9710 Digigram PCX IP LW12216 OUT 117412 Digigram PCX IP LW12216 OUT 5 1 Digigram PCX IP LW1221e OUT 7 1 Digigram PCX IP LW1221e OUT 5 142 Digigram PCX IP LW1221e PCX IP LW881e PCX IP LW1221e User s manual IN 1 2 Digigram PCX IP LW881 Digigram PCX IP LW1221e IN 3 4 Digigram PCX IP LW881 IN 5 6 Digigram PCX IP LW881 IN 7 8 Digigram PCX IP LW881 IN 5 1 Digigram PCX IP LW881 IN 7 1 Digigram PCX IP LW881 IN 5 1 2 Digigram PCX IP LW881 If the Wave driver has been installed and for OS older than Windows 7 e Goto menu lt Start gt Settings Control panel Sound and Multimedia tab Audio Default device Playback device Recording device The card s channels can be selected The card can be used with any Wave application Available Wave MME devices that can be selected from a Wave MME based application are Wave playback devices Wave recording devices PCX IP LW881e Wave PCX IP LW1221e Wave PCX
Download Pdf Manuals
Related Search