ABPM 7100 QUICK START GUIDE, EN
Contents
1. Ambulatory blood pressure gt Advanced Choose the correct Com port number in the ABPM 7100 drop down menu 7 Click OK to accept the change SETUP NEW PATIENT 1 Click s Patient to enter a new patient 2 Fill in the Patient card and click OK Note To select a patient from the database In the Patients tab enter the patient name or number into the search box and then select Go select the patient for whom you want to record the test PROGRAM YOUR DEVICE 1 Click on j ABP 2 If prompted select ABPM 7100 and click OK 3 Select Protocol Referring Physician etc and click OK The device is now programmed with the patient information 4 Disconnect the PC interface cable from the device PREPARE YOUR PATIENT FIT YOUR PATIENT WITH THE DEVICE AND CUFF WARNING strangulation risk The cuff tube and shoulder strap can wrap around the patient s neck When used on children the device must only be applied in children with special care and under permanent supervision When used on adults caution should be taken ZN warning Use only Welch Allyn approved accessories and use them according to the manufacturer s directions for use Using unapproved accessories with the recorder can affect patient and operator safety and can compromise product performance and accuracy ZN warning Patient Injury risk Do not place the cuff on any area where circulation is compromised Instruct the patient to remove the cuff immediately and n2. Jo print multiple formats the desired formats need to be selected in the print settings Select File gt Settings gt Ambulatory blood pressure gt Printing to access the print settings e To print one format click on the print icon and select the desired report PATIENT INFORMATION Ambulatory blood pressure monitoring ABPM takes numerous reading of your blood pressure over a 24 hour period or longer It provides accurate and reliable information and can give you and your doctor a truer picture of your blood pressure than occasional visits and readings taken at your doctor s office DEVICE BUTTONS Press Event to start a measurement if you are feeling an unusual event Press Start O to start a measurement If instructed to do so by your doctor Press Day Night fez immediately before going to sleep and upon waking If you are feeling or experiencing pain swelling redness or numbness in the limb where the cuff is placed remove the cuff immediately and notify your doctor PATIENT DO S amp DON TS DO e Position the device in such a way that the tube cannot be compressed e Record time symptom mood and activity position in the patient diary e Keep cuff arm motionless during readings e Keep vehicle driving and travel to a minimum e Bring the patient diary with you upon return to your doctor DON T e Remove the cuff unless you are experiencing pain swelling redness or numbness in the limb where the cuff is pla
3. AMBULATORY BLOOD PRESSURE MONITORING WelchAllyn DEVICE SAFETY For complete directions for use warnings and cautions please consult your user manual located on the software CD The cuffs and the tube are made from electrically nonconductive material and protect the device from the effects of a defibrillator discharge A N CAUTION Ensure the tube cannot be kinked or compressed when patient is resting or sleeping AN CAUTION During a defibrillator discharge the device must not be allowed to touch the patient The device can be damaged from the discharge and give inaccurate measurements AN CAUTION The device fulfills the requirements of EMC standards However it should not be exposed to strong electromagnetic fields AN CAUTION The device should not be used at the same time as high frequency surgical equipment AN CAUTION If liquids enter the device remove the device from use until it has been properly dried inspected and tested by qualified service personnel DEVICE BUTTONS Note o stop a measurement press any button starts the automatic protocol Triggers a measurement in addition to the automatic protocol Records an event and triggers an additional measurement Day Night button Patient presses immediately before going to sleep and upon waking On Off button Turns on or off device press for two seconds SIZING CHART Note Correct cuff fit is extremely important for accurate measureme
4. ced or unless you are instructed to do so by your doctor It is expected that you may experience some mild to moderate discomfort during a blood pressure measurement e Get the device wet e Swim shower or bathe during recording e Remove batteries from the device e Operate equipment or power tools Vibrations may disrupt the device reading 80019438 Ver C 2014 Welch Allyn Inc Welch Allyn Technical Support www welchallyn com support www welchallyn com
5. nt CUFF SIZE ARM CIRCUMFERENCE REUSABLE SLEEVE CUFFS Child Cuff 14 20 cm small Adult Cuff 20 24 cm Adult Cuff 24 32 cm Adult Plus Cuff 32 38 cm Large Adult Cuff 38 55 cm SOFTWARE INSTALL This Quick start guide is intended for use with CardioPerfect Workstation version 1 6 6 or higher Before you start install the CardioPerfect Workstation software and ABPM 7100 driver See the Welch Allyn CardioPerfect Workstation Installation Guide for installation instructions PROGRAM YOUR DEVICE CONNECT DEVICE TO A COMPUTER 1 Install two fresh AA batteries into the ABPM 7100 device 2 Connect the PC interface cable to the USB port on the computer Note Jo avoid repeating the device configuration steps use the same USB port Com port when connecting the device to the PC 3 Connect the other end to the ABPM 7100 device 4 Press and hold the On Off button for two seconds to turn on the device CO appears on the device screen indicating the device is connected COMMUNICATE WITH THE DEVICE 1 On the PC right click on My Computer 2 Select Properties 3 Click on Device Manager For Windows XP Device Manager is located on the Hardware tab 4 Double click Ports Com amp LPT and note the Prolific USB to serial Com port number You will need this number in the next steps 5 Open the CardioPerfect Workstation Software and log in 6 Navigate to the Advanced tab by selecting File gt Settings gt
6. otify the doctor if they are experiencing pain swelling redness or numbness in the limb where the cuff is placed as this may indicate compromised circulation 1 Place the appropriate sized cuff on the patient s non dominant bare upper arm See Sizing chart Note Correct cuff fit is extremely important for accurate measurement 2 Align the cuff tubing connector to the device fitting Click the tubing connector onto the device fitting to secure 3 Place the device into the equipment pouch Close the pouch flap 4 Put the pouch on the patient Note he pouch has a belt loop which can be used to wear the device without the strap 5 Press Start to begin automatic protocol The beep signals the start of a measurement MAKE SURE OF THE FOLLOWING BEFORE YOUR PATIENT LEAVES THE OFFICE the device is concealed according to patient s wishes the belt shoulder strap and pouch are positioned comfortably the buttons are accessible to the patient the patient has the appropriate sized cuff the patient diary and that fully charged batteries are installed in the device e Briefly explain to the patient the type of information to record in the patient diary e Remember the patient s comfort and ability can affect the relevance of the recorded data e Provide the Patient Information in this document to your patient WHEN YOUR PATIENT RETURNS RETRIEVE DATA When your patient returns remove the device and accessorie
7. s from the patient 1 If the device is on press the On Off button for two seconds to turn the device off 2 Connect the device to the computer with the PC interface cable 3 Press the On Off button for two seconds to power up the device CO appears on the device screen 4 Start the CardioPerfect Workstation Software and log in 5 Inthe Patients tab enter the patient name or number into the search box and then select Go Patients q Search Seach Go 6 Select the patient name 7 Select the test date and time I 5 oue ul amp Sv10 2008 4 17 12 FM 8 Select Read measurements 9 If prompted select ABPM 7100 and click OK Note f there is no response from the hardware click cancel and mini mize the CardioPerfect Workstation window Follow the steps in the section Communicate with the device to select the correct com port 10 Make your selections from the Ambulatory Blood Pressure Measurement read back window and click OK to transfer and save the data to the computer PRINT REPORT AND REVIEW DATA If automatic printing is checked in the ABPM print settings the report should print now If you did not select Automatic Printing in the settings e To print multiple formats click on the drop down button next to the Print icon and select Print selected formats to initiate printing Pint LA Print Preview Print Ctrl P G Print selected formats Ctri Alt P Note
Download Pdf Manuals
Related Search