Wireless Door/Window Alert
Contents
1. then activate the sensor 6 Once the sensor is programmed the green LED will be steadily on and none of the red zone LEDs will be on ai C W Separate the magnet from the sensor Receiver zone LED stops flashing Plug in the adapter to the receiver Learn Button Note Each zone can program up to 4 sensors If you try to program a fifth sensor into a zone the first programmed sensor will be erased Test Sensor After learning the sensor to the Receiver unit you may test the com munication by placing the magnet beside the sensor where the red marking is and remove the magnet from the sensor When the magnetic is closed the receiver will not beep When the magnetic contact is broken open the receiver will beep and zone LED will flash 2 PROGRAMMING CONT 1 Zone LED of this sensor will flash 2 Beeping according to the zone number Operating mode is set to Alert 1 beep for zone 1 2 beeps for zone 2 and etc until the magnetic contact is closed Erasing a sensor You cannot erase a specific sensor You must erase all sensors from the receiver then program the ones you would like to keep To erase all the sensors from the receiver 1 Remove the adapter from the receiver 2 Open the back cover press and hold the learn button Do not release the learn button until step 4 3 While holding onto the learn button plug in the adapter to the receiver 4 You may release the2. 5 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter ference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment dose cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced ra
3. Wireless Door Window Alert Model WD 434RTL 1 INTRODUCTION The Wireless Door Window Alert is designed to monitor any door or window within your house When the monitored window or door is opened the receiver will flash along with alert beeping or alarm In this package you should find a sensor a magnet a Household Alert receiver an adapter 3V lithium battery installed and other mounting accessories Magnet Sensor wo Adapter Mounting Household Alert Accessories Long Range Receiver Please follow the instructions below to setup your door window sensor and the receiver 2 PROGRAMMING The sensor must be programmed to the Household Alert Long Range Receiver before they can communication You may program the sensor to one of the 4 zones Follow the instructions below 1 Plug in an AC adapter to the receiver 2 Power up the Receiver unit The green LED will be on indicating it is turn on 3 Open the back cover and there is a learn button Press and hold this learn button for 5 seconds until both green LED and zone 1 red LED flash You may now release the learn button 4 If you would like to program the sensor to zone 1 activate the sensor while the zone 1 red LED is flashing Activate the Sensor by separating the magnetic contact from the sensor 5 If you would like to program the sensor to other zones press the learn button again until the red LED flashes at the zone you want to program the sensor to
4. dio TV technician for help 8 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 9 CUSTOMER SERVICE If you would like to order Skylink s products or have difficulty getting them to work or download information and user manual please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com P N 101Z800 2010 SKYLINK GROUP
5. learn button when the LEDs on the receiver are on 5 You have erased all sensors from the receiver 3 INSTALLATION The transmitters should be mounted on the door frame or window frame by double sided tape The magnet should be mounted on the door or window by either double sided tape or screws Make sure the magnet is aligned with the red marking on the transmitter If the surface of the frame is flat enough double sided foam tape is sufficient otherwise it is recommended to screw the mounting plate to the frame then apply double sided tape After mounting the sensor if the Skylink logo is inverted remove the front cover and rotate it so the Skylink logo is in the upright position Red Marking on the side Red Marking on the side Double sided foam tape 4 OPERATION There are 3 different operating modes for the Household Alert Long Range Receiver Mounting plate and screws optional Sensor 1 Alert Beeps when a sensor is activated corresponding zone LED will also flash 2 Alarm Sounds an alarm when a sensor is activated corresponding zone LED will also flash 3 Off No audio sound will be emitted when sensor is activated Zone LED will flash to indicate the activated sensor To select the operating mode place the slide switch on the side at the desired setting OFF No Audio ALERT Alert Mode ALARM Alarm Mode 4 OPERATION CONT Operation Alert When the magnetic contac
6. t is broken such as when the door or window is open the sensor will send a signal to the receiver It will beep and the corresponding zone red LED will flash If the sensor is set to zone 1 zone 1 red LED on the receiver will flash and the receiver will emit a continuous single beep i e beep pause beep pause etc If the sensor is set to zone 4 zone 4 red LED will flash and the receiver will emit a continuous 4 beeps i e beep beep beep beep pause beep beep beep beep pause etc By the number of beeps emitted by the receiver user can identify which zone is triggered Mute When a sensor is triggered for a long period of time you may stop the buzzer by pressing the mute button When another signal comes again you can disable the buzzer for all currently activated sensors by pressing the mute button The receive will beep again if it receives another signal For instance if you know the door window sensor will be on for a while when another family member is cleaning the window you may want to disable the buzzer for this sensor Then you can press the Mute button after it starts to sound If any other sensor is triggered the receiver will sound again Alarm When the receiver is in Alarm operation mode it will sound its siren when a sensor is activated The maximum alarm duration is set for 3 minutes To terminate the siren during the 3 min interval press the mu
7. te button Although the alarm siren is terminated if that sensor is still activated its corresponding LED will continue to flash Note This audio siren is not intended to prevent intruder break in it is rather an alert signal indicating a sensor is activated Therefore turning off the siren does not require specific password Off No audio will be emitted even sensor is activated Only zone LED will flash 5 LOSS OF SIGNAL INDICATION When the battery level on the sensor drops to a certain level or the sensor is out of the operating range the receiver will show a loss of signal indication The red LED representing that zone will flash rapidly i e if zone 1 sensor is lost the zone 1 red LED will flash rapidly When the loss of signal indication occurs move the receiver closer to the corresponding sensor and trigger that sensor If the red LED stops flash ing rapidly that means the receiver or sensor needs to be relocated If the loss of signal indication persists replace the battery of that sensor 6 OTHER HOUSEHOLD ALERT SENSORS The Household Alert Long Range Receiver can work with up to 4 different sensors garage door monitor sensor door window sensor water sensor indoor outdoor motion sensor etc Please visit www skylinkhome com or contact us at support skylinkhome com for more information of how to fully utilize your Wireless Door Window Alert 7 FCC This device complies with Part 1
Download Pdf Manuals
Related Search