Home

RADview-SC/Vmux-110

1. ACUI ML 4E1 i 2 PS2 PS1 TST ALM PWRI PWR mux 2100 o WC 2E1 2 EEE ML 4E1 eady 006 07 24 13 58 Figure 4 6 Element Manager Vmux 2100 Example 2 Click the lower half of the Element Manager window to focus on Agent mode 3 From the Options menu select Manager List The Manager List dialog box appears Note The Manager list is a list of trap destinations The agent sends traps to the IP addresses in the Manager List 4 Enter the NMS IP Address 172 17 191 12 or whatever the correct NMS IP address is for your network 5 Click Set The Manager List dialog box closes 6 Click the top half of the Element Manager window to focus on Edit mode From the Configuration menu select Read The Read Config dialog box appears Click OK 9 Repeat this procedure for the remaining two Vmux devices Vmux 110 Ver 4 0 Configuring the Network Management Station 4 9 Chapter 4 Configuring a Typical Application User s Manual 4 4 Creating Bundles In order for voice data to pass between the different Vmux devices you must create bundles between each branch site and the central site from Vmux 210 to Vmux 2100 and from Vmux 110 to Vmux 2100 In order to create a bundle between two Vmux devices you must e Launch the RADview Service Center e Add sites e Add element nodes to the sites e Create a bundle of time slots between the device at the centr
2. cceecceeeeeeeeeeeeeeeeeaeeeeeeeaaaeeeeseaaaeeeeeaaaeeeesaaaeeeesaaaaees 3 7 Setting the Operational ParaMeters ce eeeeeeeeeeeeeeeeeeeeeeeeeeeeaaaaaeeeeeeeeeeeaaaaaeeeeeeees 3 9 Configuring Signaling Profile Parameters 2 0 0 ccc eeeeeeee cece seca eeeeeeeeeeeeeeeaaaaaeeeeeeeeeeeeaaa 39 Viewing Signaling Profile Parameters ccecceeceeeeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeetentess 3 9 Changing Signaling Profile Data eect ene IU Vmux 110 Ver 4 0 i Table of Contents User s Manual Configuring Bridge POMtS sstseccccicanesteavidvasidweelac tewedees sudeedabnasiebtadigendavieauiaesbicandivdeetees 3 11 Configuring the VLAN Table siisii nnana aenn inetd chia 3 13 Configuring FXS Timeouts and Cadence 0 0 ceeceeeeeeeeeee eee eeeeeeeaeeeeeeeaaeaeeeeeaeaeeeeeaaees 3 16 CONTISUTINE Vm xX L10 POrts 2 s tisieeesssezes nanan aa E a NE a 3 19 Configuring Port INfOrmation esesssseseeessieeeeetsetttttttttttttttttttttttttttttttttttttttttttttrtttttettrttn 3 19 Copying a Port Configuratio seeren r naaa E eaea aaa E DAOIS EE i 3 35 3 3 Additional TaSKkS 2 0 ccccecee cece een ee eee reenter eee eee eee aeeee ee aan eee eaae reese dees eaaeaeeeesaaaeesesaaaes 3 36 Displaying Vmux 110 Host IP Information ssssssesesssssrrssssrrrresrrrrsrrrrresrrrressnrreenns 3 36 Displaying Analog Voice Port Status ccceceecceeeeee eee eeeeeeeaaeeeeeeeaeeeeeeeaaeeeeeesaaeeeeeeaa 3 37 Displaying Link E1 T1 Po
3. 3 Configure Telnet access and click lt Set gt A 1 172 17 158 14 Access i x Telnet z Set Cancel Get successful Figure 5 1 Access Dialog Box Table 5 1 Telnet and Web Access Parameters Possible Values Remarks Enable Disable accessing the device via Telnet Enable All users are allowed to access the device via Telnet Access Disable No one is allowed to access the device via Telnet Manager List Only Only manager stations listed in the manager s list are allowed to access the device via Telnet Default Enable Set Click lt Set gt to send new values to the Agent Cancel Vmux 110 Ver 4 0 Click lt Cancel gt to close the Access dialog box Setting Management Access Authorizations 5 1 Chapter 5 Security Management Installation and Operation Manual 5 2 UNIX Users and Permissions RADview OV when running on a UNIX based operating system supports the users and permissions security feature Only an Administrator can add or remove nodes from the Service Center map For further details refer to the chapter on Security in the RADView SC Vmux System Manual 5 2 UNIX Users and Permissions Vmux 110 Ver 4 0 Chapter 6 Performance Management This chapter describes how to monitor Vmux 110 performance and explains how to perform the following tasks e Setting the Polling Interval e Viewing Bundle Connection Statistics e Viewing Current Statistics for an E1 T1 Po
4. Parameter Possible Values Remarks Code Alarm code Port Port reporting the alarm Description Description of the alarm Status Off Event Minor Major Warning Critical Date Date in the format DD MM YYYY Time Time in the format HH MM SS Print Click lt Print gt to print the All Buffer Alarms list disabled if the list if empty Save to File Click lt Save to File gt to save the All Buffer Alarms list to a file The Save dialog box appears In the File Name field enter the name of the file In the File of type field select Acrobat pdf or HTML htm Click Save disabled if the list if empty Close Click lt Close gt to close the All Buffer Alarms list Refresh Click lt Refresh gt to update the All Buffer Alarms list 7 16 Monitoring Object Status Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management Displaying the New Buffer Alarms List The History Log gt New command enables you to display the alarm buffer that contains the alarms recorded since the last time you ran this command To display the alarm buffer for new alarms 1 In Agent mode select the device 2 From the Fault menu select History Log gt New 3 Sort the list of alarms by any one of the column values by clicking on the column header Each click toggles between ascending and descending order 4 1 172 17 158 14 New Buffer Alarms eee ares Rhee ail MAIN LINK OVERFLOW 09 07 2006 09 28 33 MAIN LINK OVE
5. 2 Select a table entry 3 Click lt Details gt The Bundle Connection Details dialog box appears with the following tabs SW Cfg 1 see Figure 3 27 and Table 3 26 SW Cfg 2 see Figure 3 28 and Table 3 27 SW Cfg 3 see Figure 3 29 and Table 3 28 SW Cfg 4 see Figure 3 30 and Table 3 29 SW Cfg 5 see Figure 3 31 and Table 3 30 4 Click the desired tab SW Cfg 1 SW Cfg 2 SW Cfg 3 SW Cfg 4 or SW Cfg 5 5 If you wish to display the Advanced Voice Parameters 1 2 Click the SW Cfg 5 tab Click lt Advanced Voice Parameters gt The Advanced Voice Parameters dialog box appears see Figure 3 32 and Table 3 31 3 44 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management 6 When you are finished viewing bundle parameters click lt Close gt SW Cfg 1 Tab 4 1 172 17 158 48 Bundle Connection Details Figure 3 27 Bundle Connection Details SW Cfg 1 Dialog Box Vmux 110 Ver 4 0 Additional Tasks 3 45 Chapter 3 Configuration Management User s Manual Table 3 76 Bundle Connection Details SW Cfg 1 Connection Parameters Parameter Bundle No Possible Values Remarks Index number of the IP Bundle 1 12 Bundle Name Unique bundle name Maximum of 10 characters Admin Status Connection status of the IP Bundle Connected Disconnected frames are not sent from this channel Dest Bundle Bundle number in the destination IPmux device 1 3
6. For a different view click on the Legend Port Ekaro anaien TE Running Time 3 days 04 03 48 a Correct Frames 81066 Bytes SIS oe ee Lt eee Broadcast Frames 85 TEE Multicast Frames 0 Reset Counters Close Poll et successful E 10sec to next polling Figure 6 9 LAN Transmit Frame Types Statistics Dialog Box 6 14 Viewing Transmit Frame Types Statistics for a LAN Port Vmux 110 Ver 4 0 User s Manual Parameter Port Chapter 6 Performance Management Table 6 8 LAN Transmit Frame Types Statistics Parameters Possible Values Remarks ETH NET ETH USER Running Time The system up time i e the time in hundredths of a second since the network management portion of the system was last re initialized Format DD days HH MM SS Status Bar Countdown Timer Displays number of seconds to next polling action Only in use when polling is enabled Tx Frame Type Table amp Graph Parameters Note The following parameters vary depending on the device s hardware version The parameters listed here are for a device hardware version of 1 1 or greater Correct Frames Counter of correct frames transmitted Bytes Counter of bytes transmitted Broadcast Frames Counter of broadcast frames Multicast Frames Counter of multicast frames Reset Counters Click lt Reset Counters gt to reset the counters of selected port to 0 Close Click lt Close gt to clo
7. Click lt Print gt to print the Port Active Alarm List Disabled if the list if empty Save to File Click lt Save to File gt to save the Port Active Alarm List to a file The Save dialog box appears In the File Name field enter the name of the file In the File of type field select Acrobat pdf or HTML htm Click Save Disabled if the list if empty Clear Click lt Clear gt to clear the selected alarm from the Port Active Alarm List Disabled if the list if empty Close Click lt Close gt to close the Port Active Alarm List dialog box Refresh Click lt Refresh gt to update the Port Active Alarm List Clearing the Port Active Alarm Buffer gt Note Vmux 110 Ver 4 0 The Alarms gt Clear command enables you to clear all entries in the active alarm buffer for a selected port To clear the Port Active Alarm buffer 1 In Agent mode select a port 2 From the Fault menu select Alarms gt Clear The next time you view the port level Active Alarm List only alarms that occur after the Clear operation appear in the list 7 2 Running Loopback Tests The Test command enables you run loop tests on a port or its time slots to troubleshoot data loss on a link and locate where the data is being lost in order to correct the problem This test is not relevant for Serial Link or Ethernet ports Running Loopback Tests 7 19 Chapter 7 Fault Management User s Manual gt Toruna test ona port 1 In Agent mode
8. Fault Menu Task Displaying the Active Alarm Buffer Displaying the System Level Active Alarm Buffer Location in User s Manual Chapter 3 Chapter 3 Mode Agent Agent Path in RADview Fault Alarms Display All Fault Alarms Display System Level Displaying the IP Bundles Active Alarm Buffer Clearing the Active Alarm Buffer Clearing the System Active Alarm Buffer Configuring Alarm Attributes Configuring Alarm Reports Chapter 3 Chapter 3 Chapter 3 Chapter 3 Chapter 3 Agent Agent Agent Agent Agent Fault we Alarms Display IP Bundles Fault ww Alarms Clear All Fault Alarms Clear Fault Alarms Configuration w Attributes Fault Alarms Configuration Reports Displaying the Alarm Buffer List Chapter 3 Agent Fault w History Log gt A ll Displaying the New Alarm Buffer List Chapter 3 Agent Fault History Log New Displaying Sanity Check Errors 2 12 Using the Graphical User Interface Chapter 3 Edit Fault Sanity Check Errors Vmux 110 Ver 4 0 User s Manual Chapter 2 Installation and Operation System Level Statistics Menu Table 2 7 System Management Options Statistics Menu Task Location in Mode Path in RADview User s Manual Viewing Bundle Connection Statistics Chapter 3 Agent Statistics Bundle Connection Table System Level Window Menu In Edit mode the Window menu is disabled gray if there i
9. select a port 2 From the Diagnostics menu select Test or From the toolbar click zi 3 From the Test drop down list select the desired test If you want to enable per time slot testing select Test per TS and then select the desired time slots 4 Configure the desired test parameters 5 Click lt Start Test gt to begin testing 6 When you are finished testing be sure to click lt Stop Test gt to return the port to normal operation A 1 172 17 158 14 Test E x Port Link T1 Current New Test None Test Local Loop v Test per TS TS Test r pifz s a sfe e s o vl ve rl rs va v5 v6 v7 ve vo 0 20 22 25 29 E Ae ma EEHSESNEERRSARARARANEEEEE Test per T5 Duration sec 1e Infinite eed Apply None LT Local Tone Injection Start Test Stop Test Refresh Get successful Cy Figure 7 13 Test Dialog Box for E1 T1 Ports with Time Slots A 1 172 17 158 13 Test a x Port FxS 2 Current p Soraa a ee Test Remote Loop v Test None Duration sec Infinite fo Start Test Stop Test Refresh Get successful m Figure 7 14 Test Dialog Box for Analog Voice Ports without Time Slots 7 20 Running Loopback Tests Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management Table 7 11 Test Parameters Parameter Possible Values Remarks Port Channel E1 Channel T1 Link E1
10. 0 Egress Tag Handling None Ingress Tag Handling None Close Refresh fet successful jE Figure 3 8 Bridge Ports Configuration Dialog Box 3 12 Setting the Operational Parameters Vmux 110 Ver 4 0 User s Manual Parameter Ingress Filtering Chapter 3 Configuration Management Table 3 7 Bridge Ports Configuration Parameters Possible Values Remarks When Ingress Filtering is enabled Vmux 110 discards incoming frames for VLANs that do not include this port in its member set When Ingress Filtering is disabled the port accepts all incoming frames This control does not affect VLAN independent BPDU frames such as GVRP and STP It does affect VLAN dependent BPDU frames such as GMRP Enable Disable Default Disable Port VID The PVID or VLAN ID that is assigned to untagged frames or Priority Tagged frames received on this port 1 4094 Default 1 Default Priority Tag The default ingress User Priority for this port This only affects media such as Ethernet that do not support native User Priority 0 7 Default O Egress Tag Handling How the Egress VLAN Tag is processed It is mainly for use with Double Tagging None Stacking Default None Ingress Tag Handling How the Ingress VLAN Tag is processed It is mainly for use with Double Tagging None Stripping Default None Close Click lt Close gt to close the dialog box Refresh
11. 2 10 System management options Agent mode 2 10 System Parameters configuring 3 4 dialog Edit mode 3 5 setting 3 2 T T1 port data stream statistics 6 9 intervals Statistics 6 8 link statistics 6 19 Telnet Access 5 1 Time and date setting 3 6 Time Slot Assigments Link E1 T1 Port displaying 3 39 Vmux 110 Ver 4 0 Index Time Slot Assignments displaying voice port 3 40 Timeouts and Cadences configuring FXS 3 16 Timeouts of an FXS port viewing 3 16 Transmit statistics Ethernet port 6 14 LAN port 6 14 Typical Application ASCII terminal connecting 4 2 logging in 4 2 bundles creating 4 13 overview 4 10 configuration summary 4 2 host IP settings configuring 4 3 manager list configuring 4 3 network nodes configuring 4 8 creating 4 5 NMS configuring 4 4 overview 4 1 RADview SC Vmux launching 4 10 requirements 4 1 sites adding 4 11 adding element nodes 4 11 SNMP management console launching 4 4 Vmux units configuring for management 4 2 connecting to the NMS 4 4 U Update Configuration dialog Edit mode 3 60 Updating agent configuration from Edit mode 3 59 Uploading current configuration from the agent 3 58 User Info of a port 3 3 User Name of a port 3 3 V Versions 1 1 VLAN Table configuring 3 13 Vmux 110 Configuration management 3 1 Index User s Manual l 4 Vmux 110 Ver 4 0
12. Disable Note This parameter is disabled when HDLC Mode is set to Cisco Bridged ETH Set Cancel 3 24 Setting the Operational Parameters Click lt Set gt to save the new values in the dialog box Click lt Cancel gt to cancel the selections made in the dialog box and close the box Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Link T1 Port Software Configuration E 1 172 17 158 47 Port Information oa ll Rey SENSILIVICY 7 oyu Sr o13 o o ooo o O A zane ix Gain level aby Disable 6100 Dele ooo Figure 3 15 Link T1 Port SW Cfg Tab Vmux 110 Ver 4 0 Setting the Operational Parameters 3 25 Chapter 3 Configuration Management User s Manual Table 3 13 Link T1 SW Cfg Tab Parameters Parameter Possible Values Remarks Port Link T1 Connect No Yes Default No Line Type The line type of the interface SF D4 ESF Default ESF Restore Time The time required to restore normal service after the end of a loss of synchronization condition FAST TR 62411 Default FAST Clock Mode Defines the clock operation mode of the interface LBT loop back timing Internal LBT from Channel Default LBT Line Code Line coding method used for zero suppression B8ZS TRANS AMI Default B8ZS coding A specified pattern of normal bits and bipolar variations replaces a sequence of 8 zero bits This option provides clear channel capa
13. Insert Manage Tools Config Window Help 440 S H DD BOPP e e Blall SI Ssteminto gt Z 2 o 25 34 e Ber ne i 10 lt mux EEE Root Subnet B x vmux IB Event History 172 17 158 14 Any Priority _ 0 x Minor 67 24 2006 11 21 51 172 17 158 14 alarmsTrap 1 alrBufDescription Displays a 67 24 2666 11 32 13 172 17 158 14 Object Changed by Administrator at 172 18 Trend Event Menu For Help press F1 localhost Administrator Supervisor Figure 4 2 SNMPc Management Console Creating the Network Nodes Before you can configure the circuits in RADview SC Vmux for each device you must first e Create the Vmux nodes in the SNMPc Management Console map according to the following table Table 4 3 Typical Application Host IP Settings Site Device Type IP Address Network Mask Gateway A Vmux 2100 172 17 158 11 255 255 255 0 172 17 158 1 B Vmux 210 172 17 158 9 255 255 255 0 172 17 158 1 C Vmux 110 172 17 158 14 255 255 255 0 172 17 158 1 gt To add a Vmux device to the SNMPc Management Console map 1 From the SNMPc map Insert menu select map Object gt device Vmux 110 Ver 4 0 Configuring the Network Management Station 4 5 Chapter 4 Configuring a Typical Application User s Manual Map Object Properties ae New Obiect foooo Bicones imm nknown Figure 4 3 Map Object Properties General Tab 2 Inthe Labe
14. Link T1 FXS FXO E amp M Current Test Description of the test currently running E1 T1 Local Loop Remote Loop Test per TS None FXS FXO E amp M Remote Loop Local Tone Injection Remote Tone Injection None New Disabled if a test is currently running Test Test description E1 T1 Local Loop Remote Loop Test per TS None FXS FXO E amp M Remote Loop Local Tone Injection Remote Tone Injection None Duration sec Duration of test to be run Infinite 1 60 Default Infinite no time limit to test length Disabled for Local Loop and Remote Loop tests Test per TS Enabled only if Test is set to Test Per TS in either New or Current group Time slot ID of the time slot to be tested 1 31 E1 1 24 T1 Test None LT Local Tone Injection Duration No test running 1 60 Duration of test in seconds Inf No time limit to test length Start Test Click lt Start Test gt to begin testing a port Stop Test Click lt Stop Test gt to stop the currently running test before its configured duration Close Click lt Close gt to close the Port Test Dialog Box Refresh Click lt Refresh gt to update the Port Test information Vmux 110 Ver 4 0 Running Loopback Tests 7 21 Chapter 7 Fault Management User s Manual 7 22 Running Loopback Tests Vmux 110 Ver 4 0 Index A About 2 10 Access setting 5 1 Agent configuration updating from Edit mode 3 59 uploading curr
15. No Bundle Name Admin Status Dest Type Dest Bundle 172 17 158 13 Phone Connected 172 17 155 240 Parameter Bundle No All Bundles One Bundle Close Refresh Ready E Figure 7 3 IP Bundle Active Alarms Dialog Box Table 7 3 IP Bundle Active Alarms Parameters Possible Values Remarks 1 12 Bundle Name Unique bundle name string maximum 10 characters Admin Status Indicates state of the link Connected Disconnected frames are not sent from this channel Dest IP IP address of the destination mux 0 0 0 0 255 255 255 255 Dest Type only on PBX Phone FXS device Dest Bundle Bundle number in the destination mux 1 30 All Bundles Click lt All Bundles gt to view a list of alarms for all Bundle Connection table entries This button is disabled if the table is empty One Bundle Click lt One Bundle gt to view a list of alarms for the selected Bundle Connection table entry This button is enabled only when a table entry is selected Close Click lt Close gt to close the dialog box Refresh Click lt Refresh gt to refresh the data displayed in the dialog box 7 6 Monitoring Object Status Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management All Bundles Active Alarm List erg A 1 172 17 158 49 All Bundles Active Alarm List o 1952 BUNDLE TSOOS major fon Nome 882 menos _major_on_Nene_ Figure 7 4 All Bundles A
16. Parameters Parameter Possible Values Remarks Source Port Selected analog voice port from which to copy configuration Destination Ports List of analog voice ports to which to copy the configuration Defaults FXS FXO E amp M 1 8 Set Click lt Set gt to copy the configuration to the selected ports Cancel Click lt Cancel gt to close the dialog box without copying the configuration 3 3 Additional Tasks Displaying Vmux 110 Host IP Information The Mux Info command enables you to view Host IP connection information about Vmux 110 such as its current IP address and default gateway gt To view Mux Host IP information 1 In Agent mode select the device 2 From the Configuration menu select Mux Info or From the toolbar click o 3 36 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management 4 1 172 17 158 14 Mux Information i i x IP Address 172 17 158 14 Default Gateway 172 17 172 1 i Refresh Get successful Em Figure 3 21 Mux Information Dialog Box Table 3 19 Mux Information Parameters Parameter Possible Values Remarks IP Address IP address of Vmux 110 0 0 0 0 255 255 255 255 Default Gateway Default gateway of Vmux 110 0 0 0 0 255 255 255 255 Close Click lt Close gt to close the Mux Information dialog box Refresh Click lt Refresh gt to refresh the data in the Mux Information dialog box Displaying Analog V
17. Signaling Profile table This button is enabled only when a table entry is selected Close In Signaling Profile table Click lt Close gt to close the dialog box Set In Change Profile Data dialog box Click lt Set gt to confirm the new value of a selected entry Cancel In Change Profile Data dialog box 3 10 Setting the Operational Parameters Click lt Cancel gt to close the dialog box without changing any settings Vmux 110 Ver 4 0 User s Manual gt Chapter 3 Configuration Management Changing Signaling Profile Data To change signaling profile parameters 1 In Edit mode only select the device 2 From the Configuration menu select Signaling Profile The Signaling Profile dialog box Figure 3 6 opens 3 Select the row of the signaling profile that you would like to change 4 Click lt Change gt The Change Profile Data dialog box Figure 3 7 opens The parameters in this dialog box are listed in 7ab e 3 6 5 Configure the desired parameters and click lt Set gt The changes are added to the NMS database and the Change Profile Data dialog box closes 6 Click lt Close gt to close the Signaling Profile dialog box Busy 1111 si Idle 0o00 Cancel Figure 3 7 Change Profile Data Dialog Box Configuring Bridge Ports Vmux 110 Ver 4 0 The Bridge Ports command enables you to configure the VLAN filtering VLAN prio
18. Statistics for a LAN Port Use the Frame Sizes command to display statistics about frame sizes and frame size errors on a LAN port gt To view frame sizes statistics for a LAN Port 1 In Agent mode select a LAN port 2 From the Statistics menu select LAN Statistics gt Frame Sizes Vmux 110 Ver 4 0 Viewing Frame Sizes Statistics for a LAN Port 6 17 Chapter 6 Performance Management gag 4 1 172 17 158 49 Frame Sizes Table and Graph Parameters User s Manual Delta rLegend 120 MUndersize m H Oversize B64 bytes 40 M64 127 bytes o e 3 01 30 jig 3 03 30 3 04 30 B512 1023 bytes For a different view click on the Legend 1024 Max bytes Port ETH NET betereserseesees serteerreee te e Running Time 4 days 04 35 03 Undersize Frames 0 3 Oversize Frames 0 64 bytes 3515369 64 127 bytes 230849 TERREN RE 128 255 bytes 351394 x 256 511 bytes 16875 512 1023 bytes 122 1024 Max bytes 0 Get successful ja 8 sec to next polling Reset Counters Close Poll Figure 6 11 LAN Frame Sizes Statistics Table 6 10 LAN Frame Sizes Statistics Parameter Undersize Frames Possible Values Remarks Total number of undersized frames Oversize Frames Total number of oversized frames 64 bytes Total number of 64 byte frames 65 127 bytes Total number of fr
19. System Level command enables you to view system level alarms gt To view system level Active Alarms 1 In Agent mode only select the device 2 From the Fault menu select Alarms gt Display gt System Level As the list of alarms is prepared a Progress Bar window illustrates the upload progress If no alarms exist the list will be empty 3 Sort the list of alarms by any one of the column values by clicking on the column header Each click toggles between ascending and descending order Monitoring Object Status 7 3 Chapter 7 Fault Management User s Manual 4 1 172 17 158 14 Mux Active Alarm List Es a E pn 18DB UPDATE OCCURRED event of None Figure 7 2 Mux Active Alarm List Dialog Box 7 4 Monitoring Object Status Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management Table 7 2 Mux Active Alarm List Parameters Parameter Possible Values Remarks Code Alarm code Description Description of the alarm Severity No Report Event Minor Major Warning Critical State On Off Mask Mask None Counter Number of times this alarm has been triggered since the last time the system was restarted or the alarm was cleared Print Click lt Print gt to print the Mux Active Alarm List This button is disabled if the table is empty Save to File Click lt Save to File gt to save the Mux Active Alarm List The Save File dialog box appears In the File Name field en
20. T1 SW Cfg Tab Parameters 3 30 Setting the Operational Parameters Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Table 3 15 Channel T1 SW Cfg Tab Parameters Parameter Possible Values Remarks Port Channel T1 Connect No Yes Default No Line Type The line type of the interface SF D4 ESF Default ESF Restore Time The time required to restore normal service after the end of a loss of synchronization condition FAST TR 62411 Default FAST Clock Mode Defines the clock operation mode of the interface LBT loop back timing Internal LBT from Link Default LBT Line Code Line coding method used for zero suppression B8ZS TRANS AMI Default B8ZS coding A specified pattern of normal bits and bipolar variations replaces a sequence of 8 zero bits This option provides clear channel capability Interface Type DSU CSU Default DSU Line Length feet Length of the cable connecting the T1 port and the network entry point This parameter affects the transmit signal mask required to meet DSX 1 requirements as specified by AT amp T CB 119 or operation requirements of FCC Rules Part 68A 0 133 134 266 267 399 400 533 534 655 Default 0 133 Disabled when Interface Type is set to CSU RX Sensitivity dBm Low 15 dBm High 36 dBm Default Low Disabled when Interface Type is set to DSU TX Gain level dBm The selected attenuation value brings y
21. Table amp Graph parameters listed here are for a device hardware version of 1 1 or greater Parameters Frames Counter of received frames Bytes Counter of received bytes Correct Frames Counter of received correct frames Correct Bytes Counter of received correct bytes Correct Broadcast Counter of received correct broadcast frames Frames Vmux 110 Ver 4 0 Viewing Receive Frame Types Statistics for a LAN Port 6 13 Chapter 6 Performance Management User s Manual Table 6 7 LAN Receive Frame Types Statistics Parameters Cont Parameter Possible Values Remarks Correct Multicast Counter of received correct multicast frames Frames Reset Counters Click Reset Counters gt to reset the counters of selected port to 0O Close Click lt Close gt to close the dialog box Poll Click lt Poll gt to update the information displayed in the dialog box 6 8 Viewing Transmit Frame Types Statistics for a LAN Port The Tx Frame Types command enables you to view Ethernet port transmit statistics gt To view transmit statistics for an Ethernet port 1 In Agent mode only select the Ethernet port 2 From the Statistics menu select LAN Statistics gt Tx Frame Types 4 1 172 17 158 48 Tx Frame Types Table and Graph Parameters x Delta 4000 Legend 2000 MiFrames Mbytes M iBroadcast Frames 10 42 30 10 43 30 10 44 30 10 45 30 B Multicast Frames Time
22. V 35 and Clock Mode is set to DTE Fragmentation bytes 200 1550 Default 610 HDLC Mode Transparent Cisco Bridged ETH Default Transparent Loop Detect Enables disables Loop Detection on the Serial Uplink Disable Enable Default Disable Note This parameter is disabled when HDLC Mode is set to Cisco Bridged ETH Set Click lt Set gt to save the new values in the dialog box Cancel gt Vmux 110 Ver 4 0 Click lt Cancel gt to cancel the selections made in the dialog box and close the box Copying a Port Configuration In order to save time and trouble once a port Is configured its software configuration can be easily copied to other ports using the port Copy command To copy a port configuration to another port 1 In Edit Mode select an FXS Port 2 From the Configuration menu select Copy 3 Click a destination port to select it Or To select multiple destination ports hold down the Control Ctrl key and click the desired destination ports 4 Ifa confirmation dialog box appears click lt OK gt to confirm that you want to copy any way and replace the existing port configurations Setting the Operational Parameters 3 35 Chapter 3 Configuration Management User s Manual The configuration is copied from the selected source port to the selected destination ports Source Port Destination Port Figure 3 20 Port Copy Dialog Box Table 3 18 Port Copy
23. Vmux 110 unit To open the Vmux 110 Element Manager from the SNMPc Management Console window PC version e Double click the Vmux 110 icon located in the map view The RADview Vmux 110 Element Manager window appears see Figure 2 3 gt To open the Vmux 110 Element Manager from the HPOV window Unix version e Select the Vmux 110 icon located in the map view and then click the zoom icon Te The RADview Vmux 110 Element Manager window appears see Figure 2 3 2 4 Launching RADview Vmux 110 Vmux 110 Ver 4 0 User s Manual Chapter 2 Installation and Operation 2 4 Using the Graphical User Interface E 1 172 17 158 48 Connected Configuration Fault Diagnostics Statistics Window Options Help ajel Ymux 110 CONTROL c SUL EITI Ei USER NET ACT LINK ACT LINK LINK CHANNEL SERIAL LINK am mux 110 ETH PWR R TO Fon CONTROL E sul EvTi E1 USER NET ACT LINK ACT LINK LINK CHANNEL SERIAL LINK Vmux 110 Ver 4 0 Figure 2 3 Element Manager Vmux 110 The RADview Vmux 110 Element Manager window provides a dynamically updated graphical representation of the Vmux 110 allowing you to monitor and manage the Vmux 110 device The Element Manager window displays e The device HW configuration showing the existing ports and their physical connectors e The Power Supply AC or internal DC e The LED status indicators of the device e Alarm Test status indication
24. according to the level selection Alarm Alarm code and description of the alarm Port Port to which the alarm applies if relevant Bundle Bundle to which the alarm applies Mask Masking status of the alarm A masked alarm is not logged in the alarm buffer no traps are set for it no LED is lit for it and it does not affect the Mux status in any way A masked alarm does appear in the Active Alarm list with a sign indicating that the alarm is masked A masked alarm cannot be cleared Add Click lt Add gt to add a new alarm entry to the Alarm Attributes List Change Mask Click lt Change Mask gt to set the mask of a selected alarm entry to Yes Remove Click lt Remove gt to effectively remove a selected alarm entry from the Alarm Attributes List by setting the mask to No Note If the selected alarm is still active it will still be displayed in the Alarm Attributes List Close Click lt Close gt to close the Alarm Attributes dialog box gt To add an alarm entry to the Alarm Attributes List 7 12 Monitoring Object Status 1 In Agent mode only select the device 2 From the Fault menu select Alarms gt Configuration gt Attributes The Alarm Attributes dialog box appears Figure 7 6 3 Click lt Add gt The Add Alarm Attributes dialog box Figure 7 7 appears The fields in the Add Alarm Attributes dialog box are described in 7ab e 7 5 Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Managem
25. and display additional voice parameters Close Click lt Close to close the dialog box Refresh Click lt Refresh gt to refresh the data displayed in the dialog box Vmux 110 Ver 4 0 Advanced Voice Parameters A 1 172 17 158 48 Advanced oice Parameters S x DTMF Detection Enable NLP Cutoff Level Amplitude 512 DTD ERL Ratio Cutoff Q3 15 Figure 3 32 Advanced Voice Parameters Dialog Box Additional Tasks 3 57 Chapter 3 Configuration Management User s Manual Parameter DTMF Detection Table 3 31 Advanced Voice Parameters Possible Values Remarks Enables or disables DTMF Dual Tone Multi Frequency detectors for this bundle Enable Disable Default Disable Note This parameter exists in version 3 11 and higher NLP Cutoff Level Amplitude The non linear processor NLP cutoff level for this bundle 0 1023 Default 512 Note This parameter is used by the echo canceller It defines the maximum absolute linear PCM amplitude of the near end signal that will cause the NLP module to be active and to mute low level residual echo amp noisy surroundings This parameter exists in version 4 0 and higher DTD ERL Ratio Cutoff The Double Talk Detection DTD Echo Return Loss ERL cutoff level Q3 0 96 Default 15 Note This parameter is used by the echo canceller when echo exists and there is voice with low volume on the line in order to determine whether the near end is t
26. configuration information displayed for the selected bundle are documented in Chapter 3 3 Select an entry in the list and click lt Statistics gt The Bundle statistics dialog box that appears is illustrated in Figure 6 3 The parameters are defined in Table 6 2 4 1 172 17 158 48 Bundle Connection Table Edeno tunde name _ admin status oest Dest unde e onde 2 Connected fi21 212 121 212 E E Connected fi21 212121 212 O O O a Figure 6 2 Bundle Connection Table Dialog Box Vmux 110 Ver 4 0 Viewing Bundle Connection Statistics 6 3 Chapter 6 Performance Management User s Manual 4 1 172 17 158 13 Bundle Statistics Figure 6 3 Bundle Statistics Dialog Box 6 4 Viewing Bundle Connection Statistics Vmux 110 Ver 4 0 User s Manual Parameter Bundle No Chapter 6 Performance Management Table 6 2 Bundle Statistics Parameters Possible Values Remarks 1 12 Index number of bundle Bundle Name Name of bundle Dest IP 0 0 0 0 255 255 255 255 IP address of the destination mux Oper Status Up Down HW Mismatch Running Time The system up time i e the time in hundredths of a second since the network management portion of the system was last re initialized Format DD days HH MM SS Counters Rx Rx Signaling Number of signaling frames received Frames Note For FXS ports only Rx Voice Frames Number of voice frames rec
27. current measurement interval When a new interval begins RADview displays a new graph The vertical axis indicates the various values of the measurements The origin of the axis represents 0 The highest point represents the maximum value of the measurements maximum 899 Viewing Current Statistics for an E1 T1 Port 6 7 Chapter 6 Performance Management User s Manual 6 5 Viewing Intervals Statistics for an E1 T1 Port RADview can display Intervals Statistics information and graphs that aggregate the statistics over 15 minute intervals The Intervals command enables you to view E1 or T1 or port level interval statistics in both table and graph format gt To view intervals statistics for an E1 or T1 Port 1 In Agent mode select an E1 or T1 port 2 From the Statistics menu select Intervals Data fag A 1 172 17 158 49 Intervals Statistics 07 00 08 30 10 00 11 30 13 00 14 30 16 00 17 30 19 00 20 30 22 00 23 30 01 00 02 30 04 00 05 30 Intervals Ending Time For a different View click on the Legend Figure 6 5 Intervals Statistics 6 8 Viewing Intervals Statistics for an E1 T1 Port Vmux 110 Ver 4 0 User s Manual Chapter 6 Performance Management Table 6 4 Intervals Statistics Parameters Parameter Possible Values Remarks Port Link E1 Link T1 Channel E1 Channel T1 No of Intervals 0 96 Interval Data One row of each of the following data points f
28. ence eee e cence eee eee eee ee ana aia dia oiha dia atat 2 4 Using the Graphical User Interface ccccceceeeeceeeeeeeaee eee eea eee eeeeaaaeeeeeeaaeeesesaaeeesesaaaeees 2 5 Editand Agent MOES freiss oinera aeieea E AKENDE 2 6 Displaying the Agent Mode VIEW cceeeeeeeeeeeeeeeeeeeeeeeaeeeeeesaeaeeeesaeaeesesaaaeeeesaaaeees 2 6 LEDS eeaeee aa E a aa O coc uae ee ae EEan 2 6 Alarm Test Status Indication Bars ccccccccsecccceceeecceeeeeeceeeeeeeeeeeeeeeceeeeeeeseeeeeeeeeess 2 7 Selecting the Device ora POIt 2 0 ieeceecetcecee cee eeee eee ea eens eee nanei eeaaa eee se aaa daitan aii ninaa da 2 8 Stat s INGICATO Sei saheesed ais evcedde aaa E usd veeccaxd reste vas EAE ARS E ERAEN 2 6 Common Dialog Buttons 0 0 cece eeeeee cece cette eee e eater eee ttres ttrt attr trutt eee eeaaaeeseeaaaeeeesaaaees 2 9 Displaying Help rriren nanninannan ayes scot oa ana aaan T ASA einai tanec e aiana nain 2 10 Displaying the Application Software Information s sseessseessessessrireerrirerrrrreerrrseeena 2 10 System Level OperatiONS ssassn innan inaa aade nnsa oiana i not Er ai ninaa 2 10 System Level Configuration MENU ccceeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaeeeaaeeaaeaaaeaaaeeaaaaaaaaaaaaaaaea 2 10 System Level Fault M nu ccccccccceccecceeceeeeeeeeeeeeeeeaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaea 2 12 System Level Statistics MENU ices scaveucssscsesssseencedoesdevedatsencadestenrsoedecosdadadanchecdecede
29. information is displayed The Read command is described in Reading Uploading the Agent Configuration on page 3 55 You should assign which Time Slots to use according to the bandwidth allocated from the carrier For example if the available bandwidth is 128 kbps then you should select two Time Slots of 64 kbps each The carrier may also require you to use specific Time Slot numbers Vmux 110 uses all of the Time Slots that you define 3 40 Additional Tasks Vmux 110 Ver 4 0 User s Manual gt Note Parameter Time Slot FXS FXO E amp M Bundle Type Dest TS Chapter 3 Configuration Management To display time slot assignments 1 In either Agent or Edit mode select the device for FXS FXO E amp M or the port for Channel E1 or Channel T1 ports 2 From the Configuration menu select Analog Voice gt TS Assignment The TS Assignment dialog box appears displaying IP Bundle Connections Each Bundle Connection contains the Time Slots numbers of the bundle and their Destination Time Slots numbers To display the Sub Channel Types and Sub Channel Masks for a Time Slot move the mouse pointer over the desired Time Slot If the Time Slot contains Sub Channels then a Tool Tip appears displaying the details of the Sub Channels TS Assignment Dialog Box Analog Voice Port E 1 172 17 158 41 4E amp M TS Assignment x Time Slot E amp M a 2 3 4 Bundle Type Des
30. is disabled when HDLC Mode is set to Cisco Bridged ETH Set Click lt Set gt to save the new values in the dialog box Cancel Vmux 110 Ver 4 0 Click lt Cancel gt to cancel the selections made in the dialog box and close the box Channel E1 Port Software Configuration 172 17 158 48 Port Information E 1 Port Channel E1 Connect No X Line Type E1 MF G 7325 X Restore Time FAST z Clock Mode LBT M Interface Type DSU X Line Impedance Poo Idle Code hex 00 M Signaling Mode CAS 557 FISU Suppression Profile Number 1 v Set a TETTE E E Figure 3 16 Channel El SW Cfg Tab Parameters Setting the Operational Parameters 3 27 Chapter 3 Configuration Management User s Manual Parameter Port Connect Line Type Restore Time Clock Mode Table 3 14 Channel E1 Port SW Cfg Tab Parameters Possible Values Remarks Channel E1 Indicates whether the port should be considered in any of the Vmux algorithms No Yes Default No The line type of the interface E1 MF G 732S E1 G 732N E1 CRC G 732NCRC E1 CRC MF G 732SCRC Default E1 G 732N The time required to restore normal service after the end of a loss of synchronization condition FAST TR 62411 CCITT G 732 Default FAST Defines the clock operation mode of the interface LBT loop back timing Internal
31. l 2 3 Display the System menu Configuration gt System Disable the router Save the changes Configuring the IP Parameters The Vmux 110 host IP parameters may be assigned automatically via DHCP or they may be configured manually gt To manually configure the host IP parameters l 2 3 4 5 6 Note Display the Host IP menu Configuration gt System gt Management gt Host IP Disable the DHCP client mechanism Save the changes Enter the new host IP parameters for Vmux 110 Host IP address IP subnet mask Default gateway Set the SNMP Read Write and Trap Communities for Vmux 110 to public Save the changes In order to manually configure the Host IP Parameters the Vmux 110 router must be disabled 2 2 Pre configuring Vmux 110 for Network Management Vmux 110 Ver 4 0 User s Manual Chapter 2 Installation and Operation Configuration gt System gt Management gt Host IP IP Address 172 17 172 191 Subnet Mask 255 255 255 0 Default Gateway 172 17 172 1 DHCP Client Disable Read public Write private Trap public Figure 2 1 Configuring the Host IP Parameters Configuring the Manager List In order to remotely configure Vmux 110 the NMS needs to be listed in the Manager List The Manager List command enables you to display and configure the Manager List where you designate the destination NMS stations for SNMP traps gt To configure
32. lost F 3 Cancel FERS E Figure 3 35 Reset Configuration Dialog Box Polling the Agent The Poll Agent command causes the device to immediately poll the Agent This command is useful if you configure the device NOT to perform periodic polling of the Agent Using this command you can perform a one time polling to update the device s status gt To poll the Agent 1 In either Agent or Edit mode select the device 2 From the Configuration menu select System Commands gt Poll Agent The device immediately polls the agent Resetting Vmux 110 The Reset HW command enables you to reset the Agent s hardware to re initialize the main board CPU of the Vmux 110 unit Use this command to reset Vmux 110 in the unlikely event that the device is unresponsive has locked up or is behaving erratically gt Toreset the hardware 1 In Agent mode only select the device 2 From the Configuration menu select System Commands gt Reset HW 3 Click lt OK gt The Agent s hardware resets the Vmux 110 unit is re initialized and its active software is decompressed and loaded into the RAM Vmux 110 Ver 4 0 Additional Tasks 3 61 Chapter 3 Configuration Management User s Manual 4 1 172 17 158 14 Reset Figure 3 36 Reset HW Dialog Box 3 62 Additional Tasks Vmux 110 Ver 4 0 Chapter 4 Configuring a Typical Application This chapter provides detailed instructions for setting up a typical application us
33. or 2 T Transparent C1 C2 C3 C4 C5 C6 C7 C8 HDLC Transparent Sub Channel Number V voice H HDLC Phase 2 compatible No Connection Note e Analog Voice ports are always type V e When the device on the other side of the link is running software version 2 x the only only valid Time Slot Types are No Connection V and H e The H value is only possible when the device on the other side is a Vmux 110 or a Vmux 2100 and it is running software version 2 x Port Destination Port Note if the destination port is an analog port then this parameter row is not displayed TS Destination TS Close Click lt Close gt to close the dialog box 3 42 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Displaying Bundle Connection Parameters The Bundle Connection Table command enables you to view IP Bundle connection parameter values Voice timeslots are grouped together into bundles Vmux 110 supports 12 bundles with a maximum of 30 timeslots per bundle For information on creating and managing bundle connections using the Service Center refer to Chapter 7 of the RADview SC Vmux System Manual gt To view the Bundle Connection Table parameters 1 In either Agent or Edit mode select the device 2 From the Configuration menu select Bundles Connection Table Note The Bundle Connection Table provides general information about each bundle connection More details are provided in
34. s Manual Chapter 3 Configuration Management Configuring Vmux 110 Ports Note Vmux 110 Ver 4 0 Configuring Port Information The Port Info command enables you to view general information about the selected port and to configure the various parameters of the port the port s software configuration The parameters vary according to the port type To view or set port information l 2 In Agent mode for viewing or Edit mode for Setting select a port From the Configuration menu select Port Info or From the toolbar click oj The Port Information Dialog Box appears Click either the Info tab or the SW Cfg tab to view or set the desired information The Info tab only appears in Agent mode 4 Configure the desired parameters the following tables describe the Port Information parameters Click lt Set gt If a confirmation dialog box appears click lt OK gt to save the changes For See General port information Figure 3 12 and Table 3 10 Agent mode only ETH port software Figure 3 13 and Table 3 11 configuration Link E1 port software Figure 3 14 and Table 3 12 configuration Link T1 port software Figure 3 15 and Table 3 13 configuration Channel E1 port software Figure 3 16 and Table 3 14 configuration Channel T1 port software Figure 3 17 and Table 3 15 configuration Analog Voice port software Figure 3 18and Table 3 16 configuration Serial link software Figure 3 19 and Table 3 17
35. s Manual Parameter Link E1 or Link T1 Table 3 21 TS Assignment Parameters Possible Values Remarks Time Slot Number El 1 31 T1 1 24 Cells are color coded to indicate time slot usage or availability Green In use Gray Available except for time slot 16 of an E1 port Dark Blue Non connectable and Line Type is E1 MF or E1 CRC MF To network Status of the time slot x The time slot is allocated empty The time slot is available Cells are color coded to indicate time slot usage or availability Yellow In use Gray Available Dark Blue Non connectable for example time slot 16 of an E1 or E1 CRC port Close Click lt Close gt to close the dialog box The left most column also changes color to indicate aggregate usage or availability in the following manner Green All of the time slots are used Gray All of the time slots are available Yellow Some of the time slots are used Displaying Voice Port Time Slot Assignments Note The TS Assignment command enables you to display time slot assignments for IP bundles For information on creating and managing bundle connections and time slots using the Service Center refer to Chapter 7 of the RADView SC Vmux System Manual This dialog box is useful in Edit mode even when there is no connection with the Agent When there is a connection with the Agent perform a Read before opening the TS Assignment dialog box to ensure that the most up to date
36. seconds since the beginning of the current 15 minute interval sec 0 899 ESs Errored Seconds Number of seconds in the current interval in which an event or alarm occurred SESs Severe Errored Seconds Number of seconds in the current interval in which at least 320 CRC events or one OOF event occurred UASs Unavailable Seconds Number of seconds in the current interval in which a failed signal state exists A failed signal state occurs after 10 consecutive severe errored seconds This state is cleared only after the Vmux processes 10 consecutive seconds of data without an SES CSSs Controlled Slip Seconds Number of seconds in the current interval in which at least one controlled SLIP event occurred BESs Bursty Errored Seconds Number of seconds in the current interval in which 2 319 CRC events occurred Close Click lt Close gt to close the Current Statistics dialog box Poll Click lt Poll gt to update the information displayed in the dialog box Vmux 110 Ver 4 0 The Current Graph shows Vmux performance statistics in the current measurement interval Each interval is 15 minutes 899 seconds Lines of various colors represent a measurement item A legend on the right side of the dialog box indicates the measurement items and their respective color indications For example Figure 6 4 shows that no errors occurred during the current interval The horizontal axis indicates the time elapsed in seconds since the beginning of the
37. steps of 10 Default 0 No Suppression Note e Example For a value of 10 1 keep alive packet will be discarded out of every 10 keep alive packets that were supposed to be sent over the network e When Signaling Mode is set to Robbed Bit this parameter is grayed out and unavailable Profile Number The Signaling Profile of the port 1 5 Default 1 Note When Signaling Mode is set to CCS this parameter is grayed out and unavailable Set Click lt Set gt to save the new values in the dialog box Cancel Click lt Cancel gt to cancel the selections made in the dialog box and close the box 3 32 Setting the Operational Parameters Vmux 110 Ver 4 0 User s Manual Parameter Port Chapter 3 Configuration Management Analog Voice Port Software Configuration Port ESRT E amp M Type sos x Wires hwre Tx Gain dB poo o H Rx Gain dB fo i x Set Cancel Le Figure 3 18 Analog Voice Port SW Cfg Tab Table 3 16 Analog Voice Port SW Cfg Tab Parameters Possible Values Remarks FXS 1 FXS 8 FXO 1 FXO 8 E amp M 1 E amp M 8 E amp M Type Type 1 Type 2 Type 3 SSDC5 Default Type 1 Note This parameter is visible for E amp M ports only in groups of 4 ports 1 4 and 5 8 Wires 2WIRE 4WIRE Default 4WIRE Note This parameter is visible for E amp M ports only in groups of 2 ports 1 2 3 4 etc Tx Gain dB The selected attenuat
38. the Bundle Connection Details dialog Click on the Details button to view all data for a selected bundle see below gag E 1 172 17 158 49 Bundle Connection Table Bundle No Bundle Name Admin Status O Desp Dest Type Dest ne ae 172 17 158 13 LE eee 172 17 155 240 Details Close Refresh Figure 3 26 Bundle Connection Table Vmux 110 Ver 4 0 Additional Tasks 3 43 Chapter 3 Configuration Management User s Manual Parameter Bundle No Table 3 25 Bundle Connection Parameters Possible Values Remarks 1 12 Bundle Name Unique bundle name string maximum 10 characters Admin Status Indicates state of the link Connected Disconnected frames are not sent from this channel Dest IP IP address of the destination mux 0 0 0 0 255 255 255 255 Dest Type PBX Phone Note This parameter is only visible when the Vmux 110 contains FXS ports Dest Bundle Bundle number in the destination mux 1 30 Default 1 Details Click lt Details gt to view detailed configuration information for the selected Bundle Connection table entry This button is enabled only when a table entry is selected Close Click lt Close gt to close the dialog box Refresh Click lt Refresh gt to refresh the data displayed in the dialog box Bundle Connection Details To view Bundle Connection details 1 In either Agent or Edit mode open the Bundles Connection Table
39. the Manager List 1 Display the Manager List menu Configuration gt System gt Management gt Manager list 2 Enter the Manager IP address of the Network Management Station 3 Save the changes Configuration gt System gt Management gt Manager list Manager ID IP Address 1 172 17 172 100 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Change cell 0 0 0 0 Figure 2 2 Configuring the Manager List Vmux 110 Ver 4 0 Pre configuring Vmux 110 for Network Management 2 3 Chapter 2 Installation and Operation User s Manual Note 2 2 Connecting Vmux 110 to the Management Station Vmux 110 can be managed by a Network Management Station NMS that is located on the LAN hub or switch connected to the one of the unit s Ethernet ports To connect Vmux 110 to the Network Management Station 1 Connect a Network Management Station to the LAN hub or switch 2 Connect one of the Vmux 110 s Ethernet ports to the LAN Normally Vmux 110 management is performed out of band via the USER port To enable in band management via the NET port you may need to configure additional parameters 2 3 Launching RADview Vmux 110 To monitor and manage the Vmux 110 device using the RADview Vmux 110 Element Manager application it must first be opened or launched The Element Manager can be opened from the SNMPc Management Console PC version or from HPOV Unix version A separate RADview Vmux 110 Element Manager window can be opened for each
40. thepercentage of SS7 Keep Alive packets that will be discarded 0 No Suppression 10 90 in steps of 10 Default 0 No Suppression Note e Example For a value of 10 1 keep alive packet will be discarded out of every 10 keep alive packets that were supposed to be sent over the network e When Signaling Mode is set to CAS this parameter is grayed out and unavailable The Signaling Profile of the port 1 5 Default 1 Note e When Signaling Mode is set to CAS the Profile Number parameter is grayed out and unavailable e When Line Type is set to G 732N no MF the signaling profile is not applicable and is ignored Click lt Set gt to save the new values in the dialog box Cancel Vmux 110 Ver 4 0 Click lt Cancel gt to cancel the selections made in the dialog box and close the box Setting the Operational Parameters 3 29 Chapter 3 Configuration Management User s Manual Channel T1 Port Software Configuration E 1 172 17 158 47 Port Information Port Channel T1 Connect No hd Line Type ESF v Restore Time rast tia Clock Mode LBT z Line Code fess H Interface Type DSU v Line Length feet 0 133 v Rx Sensitivity flow 15dBm Tx Gain level dB fo 7 Idle Code hex 7F X Signaling Mode Robbed Bit 557 FISU Suppression Ea ant etc TS Rate Kbps 64 v Profile Number 1 v Cancel Figure 3 17 Channel
41. to close the dialog box Refresh 3 52 Additional Tasks Click lt Refresh gt to refresh the data displayed in the dialog box Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management SW Cfg 4 Tab E 1 172 17 158 46 Bundle Connection Details Ringback Disable Immediate On Hook Detect while Ringing Disable Enable io Frequency KH2j 12 WE Duration msec OE Figure 3 30 Bundle Connection Details SW Cfg 4 Dialog Box Note The SW Cfg 4 tab is only visible if the Vmux 110 has analog ports for example FXS FXO or E amp M ports Vmux 110 Ver 4 0 Additional Tasks 3 53 Chapter 3 Configuration Management User s Manual Table 3 29 Bundle Connection Details SW Cfg 4 Connection Parameters Parameter Bundle No Possible Values Remarks 1 12 Signaling Parameters Signaling Bits On Hook 1st LSB Nibble representing the ON HOOK signal the same for transmit and receive 0000 1111 Default 1010 DCBA Off Hook 2nd LSB Nibble representing the OFF HOOK signal the same for transmit and receive 0000 1111 Default 1011 DCBA Ring 4th LSB Nibble representing the RING PATTERN 1 signal 0000 1111 Default 1011 DCBA Note This parameter is enabled for FXS ports only Ring Il 5th LSB Nibble representing the RING PATTERN 2 signal 0000 1111 Default 1011 DCBA Note This parameter is enabled for FXS ports only Rev
42. 0 Transport Protocol TDM over IP AAL2 over MPLS TDMoIP AAL20MPLS Note In the CLI ASCII terminal this parameter is called Function TDMoIP and AAL2oMPLS use header compression The values TDMoIP and AAL2oMPLS only exist in version 3 11 and higher MTU Max Transmission Unit The largest packet size that can be transmitted over this IP Bundle 100 1461 Default 500 Packet Interval msec Defines maximum amount of time msec between multiplexed frames that are sent 10 90 in steps of 10 Default 30 Note In the CLI ASCII terminal this parameter is called Packetizing Interval No of Transmissions for Each Packet The number of times to retransmit a voice frame 1 4 Default 1 Note This parameter exists in version 3 11 and higher Signaling Type of Service TOS Note In versions prior to 3 11 there is only one TOS group the group is called Type of Service Precedence Type of Service Priority of traffic from this IP Bundle over the network Routine Priority Immediate Flash Flash Override CRITIC ECP Inter network ctrl Network Control Default Routine Type of service for traffic from this IP Bundle Normal High Reliability High Throughput High Throughput Hi Reliability Low Delay Low Delay High Reliability Low Delay High Throughput Low Delay High Throughput High Reliability Default Normal Media Type of Service TOS Precedence 3 46 A
43. 0 Version 1 1 or greater Viewing Statistics for an E1 T1 or a Serial Port Link Chapter 6 Agent Statistics Link Statistics Vmux 110 Ver 4 0 Using the Graphical User Interface 2 15 Chapter 2 Installation and Operation User s Manual 2 16 Using the Graphical User Interface Vmux 110 Ver 4 0 Chapter 3 Configuration Management This chapter describes how to configure Vmux 110 on all levels including system and port and contains the following sections e Setting the System Parameters Configuring System Information Setting Port User Information Configuring System Parameters Selecting the Date Format Setting the Date and Time Configuring the Manager List e Setting the Operational Parameters Configuring Signaling Profile Parameters Configuring Bridge Ports Configuring the VLAN Table Configuring FXS Timeouts and Cadences Configuring Vmux 110 Ports e Additional Tasks Note Displaying Vmux 110 Host IP Information Displaying Analog Voice Port Status Displaying Link E1 T1 Port Time Slot Assignments Displaying Voice Port Time Slot Assignments Displaying Bundle Connection Parameters Reading Uploading the Agent Configuration Updating Downloading the Configuration to the Agent Resetting Vmux 110 to the Default Configuration Polling the Agent Resetting Vmux 110 Access Agent mode by selecting the bottom image of the device Access Edit mode by selecting the top image of the device Vmux 110 Ver 4 0 S
44. 1 48 Analog Voice 1 4 or 1 8 Note This parameter exists in version 4 0 and higher Disable Enable Note This parameter is only displayed for E1 T1 bundles 1780 2000 1780 and 2000 Note This parameter exists in version 3 11 and higher Disable Enable A Law u Law Note This parameter is disabled for FXS FXO EEM bundles 2 10 Note This parameter is disabled for FXS FXO EEM bundles 0 3000 in steps of 100 Default 400 Note e Inthe CLI ASCII terminal this parameter is called CLID Tx Delay e This parameter is enabled only when Voice Coding is set to G729A 8 Kbps e This parameter exists in version 3 11 and higher Additional Tasks 3 49 Chapter 3 Configuration Management User s Manual Parameter Noise Level for VAD Comfort Noise Generation Close Refresh Table 3 27 Bundle Connection Details SW Cfg 2 Connection Parameters Cont Possible Values Remarks Defines the level of noise on the line that the Voice Activation Detector VAD will have to handle Low High Off Default Low Note High optimizes the VAD for environments where background voice as well as background noise must be carried across the link such as in environments where conference bridges and speaker phones are used Low reduces the background noise passed across the link and therefore reduces the bandwidth consumed Off is only available when Voice Coding is not set to G711 A Law or G711 u Law 7he OFF v
45. 1 Link T1 Running Time The system up time i e the time in hundredths of a second since the network management portion of the system was last re initialized Format DD days HH MM SS Rx Octets Number of octets received Error Frames The number of frames received that included errors Discarded Frames The amount of discarded frames received TX Octets Number of octets transmitted Error Frames The number of frames sent that included errors Discarded Frames The amount of discarded frames sent Reset Counters Click lt Reset Counters gt to reset the counters of selected port to 0 Close Click lt Close gt to close the dialog box Poll Click lt Poll gt to update the information displayed in the dialog box 6 20 Viewing Statistics for an E1 T1 or Serial Port Link Vmux 110 Ver 4 0 Chapter 7 Fault Management This chapter describes Vmux 110 fault management and explains how to perform the following tasks e Viewing All Active Alarms e Viewing System Level Active Alarms e Viewing IP Bundles Active Alarms e Clearing the System Level Active Alarm Buffer e Clearing All Levels of the Active Alarm Buffer e Configuring Alarm Attributes e Configuring Alarm Reports e Sanity Checking Errors e Displaying the All Buffer Alarms List e Displaying the New Buffer Alarms List e Displaying the Port Active Alarm Lists e Clearing the Port Active Alarm Buffer e Ru
46. 60 Current data viewing 6 6 Current Statistics dialog Agent mode 6 6 D Date amp Time setting 3 6 Setup dialog Agent mode 3 7 Date format selecting 3 6 Device selecting 2 8 Downloading a specific Edit configuration to the agent 3 59 E El port data stream statistics 6 9 intervals Statistics 6 8 link statistics 6 19 Edit Configuration mode see Edit mode 2 6 Edit mode introduction 2 6 Edit mode dialogs FXS Timeouts and Cadence 3 17 Read Configuration 3 59 System Parameters 3 5 Update Configuration 3 60 Error Statistics for a LAN Port 6 15 Ethernet port receive statistics 6 12 transmit statistics 6 14 F FCAPS model 1 2 Frame sizes Statistics for a LAN Port 6 17 FXS port viewing cadence values 3 16 viewing timeouts 3 16 FXS Timeouts and Cadences configuring 3 16 FXS Timeouts and Cadences dialog Edit mode 3 17 Index G Graphical user interface 2 5 H Hardware resetting 3 61 Help displaying 2 10 Host IP Information displaying 3 36 Indicators status 2 8 Installation and Operation 2 1 Interfaces 1 1 Intervals Statistics dialog Agent mode 6 8 Introduction 1 1 L LAN port error statistics 6 15 frame sizes statistics 6 17 receive statistics 6 12 transmit statistics 6 14 LAN Receive dialog Agent mode 6 13 LAN Transmit dialog Agent mode 6 14 LEDs 2 6 Link statistics 6 19 M Management connecting Vmux to the NMS 2 4 functions 1 3 opt
47. Alarm List nes eme wey sae ns came nan 99 BUNDLE 15 005 SRG TEEN Clear Save to File Print Close Refresh Ready ja Figure 7 5 Bundle Active Alarm List Dialog Box Clearing the System Level Active Alarm Buffer The Clear command enables you to clear the system level active alarm buffer To clear system level active alarms 1 In Agent mode only select the device 2 From the Fault menu select Alarms gt Clear Note Alarms that are masked are not cleared Vmux 110 Ver 4 0 Monitoring Object Status 7 9 Chapter 7 Fault Management User s Manual Clearing All Levels of the Active Alarm Buffer The Clear All command enables you to clear the alarm buffer at all levels gt To clear the Active Alarm buffer at all levels 1 In Agent mode only select the device 2 From the Fault menu select Alarms gt Clear All Note e Alarms that are masked are not cleared e fan alarm continues to be triggered for any reason that alarm will not be cleared because it will immediately reappear as soon as It is retriggered Configuring Alarm Attributes The Configuration gt Attributes command enables you to define alarms for each level and set masking criteria for the alarms gt To configure Alarm Attributes 1 In Agent mode only select the device 2 From the Fault menu select Alarms gt Configuration gt Attributes 3 Click the radio button next to the category of alarms you wish to dis
48. Click lt Refresh gt to re load and display the current parameters Set Click lt Set gt to save the changes Cancel Click lt Cancel gt to cancel the selections made in the dialog box and close the box Note The Link Channel Ming tab is only enabled when the router is disabled Configuring the VLAN Table The VLAN Table command enables you to configure the list of virtual LANs VLANs A VLAN is a logical virtual network of devices that behave as if they are on the same physical LAN segment even if they are physically connected to different network segments In addition multiple VLANs can co exist on the same switching hardware providing a form of logical network segmentation Vmux 110 Ver 4 0 Setting the Operational Parameters 3 13 Chapter 3 Configuration Management User s Manual Note The VLAN Table is unavailable when either of the following is true e The router is enabled the Net User Routing Mode is Layer 3 Routing and the Connect Through value is Serial Link or Link E1 T1 e The router is enabled and the Connect Through value is ETH NET e The VLAN Table menu option is not displayed when the Vinux 110 hardware version is less than 1 10 gt To view the VLAN Table 1 In Agent mode for viewing or Edit mode for setting select the device 2 From the Configuration menu select VLAN Table E 1 172 17 158 14 LAN Table Figure 3 9 VLAN Table Edit Mode 3 14 Setting the Operati
49. LBT from Link Default LBT Interface Type Interface type DSU LTU Default DSU Line Impedance Unbalanced 75 Ohm Balanced 120 Ohm Default Balanced Idle Code hex Hexadecimal code transmitted to fill idle unused time slots in frames transmitted through the selected port 00 FF Default FF Note The following values are not allowed OH 8H 10H 12H 21H 24H 42H 49H 84H 92H Signaling Mode The signaling mode of the Framer module CAS Channel Associated Signaling is a signaling method used for E1 Links CCS Common Channel Signaling The signaling is not within the channel s time slot Instead a separate time slot is reserved and used for signaling Default CAS Note e When Line Type is set to EI MF or E1 CRC MF only CAS is available e When Line Type is set to El or E1 CRC only CCS is available 3 28 Setting the Operational Parameters Vmux 110 Ver 4 0 User s Manual Parameter SS7 FISU Suppression Profile Number Set Chapter 3 Configuration Management Table 3 14 Channel El Port SW Cfg Tab Parameters Cont Possible Values Remarks S87 Suppresion is used for SS7 Spoofing The SS7 spoofing terminates the keep alive messages from the local VMUX without sending them over the network thus improving the bandwidth utilization FISU means Fill in Service Unit The keep alive that is sent when no one Is talking on the line This object enables the configuration of
50. RADview SC Vmux Network Management System Service Center for Vmux Applications Vmux 110 1994 2007 RAD Data Communications Publication 01 07 Chapter 1 1 1 1 2 Chapter 2 2 1 2 2 2 3 2 4 Chapter 3 3 1 3 2 Contents Introduction Overview of the Vmux 110 Device s seserssssssrrererrrrnrersrrrrererrrrnrrrsrrerererrnrerererrerrrerr 1 1 WL ETTACES uenici satenidaavatatastedanbiedenneceiadonndey nagcuanedagdatdeeanabendebancnntades 1 1 RADview SC VmUX 110 OVErViCW ccccecccceccceecceceeceseeceeueceeeeueesuaseeueueuseueesaaeesueeeenaaeess 1 2 Overview of the RADview FCAPS Model ccccccceceeceeeeeceeeeeeeeeeeceeeeeeeeeeeeeeeaeeaeeees 1 2 Overview of the Vmux 110 Management FUNCTIONS cceeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaeeees 1 3 Installation and Operation Pre configuring Vmux 110 for Network Management s sseeesssesssisesrrrsessriresrrrrresrrens 2 1 Connecting a Terminal to the Control POrt esssssssssessrssssrriresrriressrrrssrrrerssrrrrersrrrne 2 1 Disabling the ROUTE sigoni i ddd ee eR eee ei ete 2 2 Configuring the IP Parameters sssssssssssrsssrrtsssrerisrnserssnrissrnnriosrnterssnreeernsrresnreet 2 2 Configuring the Manager List ceeceeteeeeeeeeeeeee eee tees e ea aeeeee saan eeeeaaeeeeesaaaeeeesaaaeeeees 223 Connecting Vmux 110 to the Management Station ccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaaees 2 4 Launching RADVieW VMUX 110 ceeee cece
51. RFLOW 09 07 2006 09 29 43 MAIN LINK OVERFLOW 09 07 2006 09 31 13 MAIN LINK OVERFLOW 09 07 2006 09 32 23 MAIN LINK OVERFLOW 09 07 2006 09 33 53 MAIN LINK OVERFLOW 09 07 2006 09 35 03 MAIN LINK OVERFLOW 09 07 2006 09 37 33 MAIN LINK OVERFLOW 09 07 2006 09 37 43 MAIN LINK OVERFLOW 09 07 2006 09 39 13 MAIN LINK OVERFLOW 09 07 2006 09 39 51 MAIN LINK OVERFLOW 09 07 2006 09 41 21 MAIN LINK OVERFLOW 09 07 2006 09 42 31 MAIN LINK OVERFLOW 09 07 2006 09 44 01 MAIN LINK OVERFLOW 09 07 2006 09 45 11 MAIN LINK OVERFLOW 09 07 2006 09 46 41 MAIN LINK OVERFLOW 09 07 2006 09 47 51 MAIN LINK OVERFLOW 09 07 2006 09 49 21 __ MAIN LINK OVERFLOW 09 07 2006 09 49 52 MAIN LINK OVERFLOW 09 07 2006 09 51 22 Figure 7 11 New Buffer Alarms Dialog Box Table 7 9 New Buffer Alarms Parameters Parameter Possible Values Remarks Code Alarm code Port Port reporting the alarm Description Description of the alarm Status Off Event Minor Major Warning Critical Date Date in the format DD MM YYYY Time Time in the format HH MM SS Print Click lt Print gt to print the New Buffer Alarms list disabled if the list if empty Save to File Click lt Save to File gt to save the New Buffer Alarms list to a file The Save dialog box appears In the File Name field enter the name of the file In the File of type field select Acrobat pdf or HTML h
52. Setup Dialog Box Table 3 4 Date amp Time Setup Parameters Parameter Possible Values Remarks Format Date format selected with the Date Format command Date System date in the format selected Time System time in HH MM SS format Set Click lt Set gt to send new values to the agent Cancel Click lt Cancel gt to cancel the selections made in the dialog box and close the box Configuring the Manager List In order to remotely configure Vmux 110 the IP address of the NMS must be listed in the Manager List The Manager List command enables you to display and configure the Manager List where you designate the destination NMS stations for SNMP traps gt To configure the manager list 1 In Agent mode select the device 2 From the Options menu select Manager List 3 Configure the desired parameters and click lt Set gt Vmux 110 Ver 4 0 Setting the System Parameters 3 7 Chapter 3 Configuration Management User s Manual 4 1 172 17 158 14 Manager List Manager Id IP Address 172 17 150 94 2 172 17 150 86 60C i SCS 3 172 18 159 33 60i itsti Cs S 4 foooo 5 oooo 6 booo o 7 fPooo oo oo 10 oooo Set Cancel Refresh et successful E Figure 3 5 Manager List Dialog Box Table 3 5 Manager List Parameters Parameter Possible Values Remarks Manager ID 1 10 IP Address An IP address of 0 0 0 0 means th
53. T Mode Ping z Media Type of Service TOS Precedence Routine v Packet Frequency sec feo Type of Service Normal v Timeout Cycles fs X lt Back Next gt Finish ETI Figure 4 13 Typical Application State 2 Dialog Box Note When creating bundles you may want to configure additional parameters For more information about configuring bundle parameters see the RADview SC Vmux User s Manual 7 Click Next The State 3 dialog box appears see Figure 4 14 8 To assign a time slot drag from the Source Port cell to the Destination Port cell according to the following table For the first part of our example creating a bundle from Site A to Site B you can use time slots 10 11 and 12 Later you can use 5 6 and 7 Table 4 5 Assigning Time Slots to Bundles Bundle Being Created From Source Port Destination Port Site A to Site B 10 10 11 11 12 12 Site A to Site C 5 5 6 6 7 7 Vmux 110 Ver 4 0 Creating Bundles 4 15 Chapter 4 Configuring a Typical Application errs Manual 4 Configuring a Typical Application User s Manual Circuit Time Slot Assignment x c mee ECTE Ba Cee a l oioi AOOO a BRR Figure 4 14 Typical Application State 3 Dialog Box After Adding Bundles 9 Click Finish You have defined a bundle using RADview Service Center 10 Verify that the line from Site A to Site B turns green Note The link re
54. Tab Setting the Operational Parameters 3 21 Chapter 3 Configuration Management Parameter Port Physical Address Agent Mode only Auto Negotiation Max Capability Advertised Default Type User s Manual Table 3 11 ETH Port SW Cfg Tab Parameters Possible Values Remarks ETH NET ETH USER MAC Address 6 Octets Whether Auto Negotiation is enabled Default Enabled 1OBASE T Half Duplex 1OBASE T Full Duplex 1OOBASE TX Half Duplex 100BASE TX Full Duplex Default LOOBASE TX Full Duplex Defines the rate and duplex mode of an ETHERNET port Applicable only when Auto Negotiation is disabled 10BASE T Half Duplex 10BASE T Full Duplex 1OOBASE TX Half Duplex 1OOBASE TX Full Duplex Default LOOBASE TX Full Duplex Input Rate Limit Kbps Disabled 128 256 512 1024 2048 4096 8192 Default Disabled Set Click lt Set gt to save the new values in the Port Information dialog box Cancel Click lt Cancel gt to cancel the selections made in the dialog box and close the box Close Click lt Close gt to close the Port Information dialog box Refresh Click lt Refresh gt to refresh the data in the Port Information dialog box 3 22 Setting the Operational Parameters Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Link El Port Software Configuration gig E 1 172 17 158 49 Port Information Loop Di Figure 3 14 Link E1 Port SW Cfg T
55. a non integral number of octets Alignment Error CRC Error Frames Total number of packets received that had a length excluding framing bits but including FCS octets of between 64 and 1518 octets inclusive but had either a bad Frame Check Sequence FCS with an integral number of octets FCS Error or a bad FCS with a non integral number of octets Alignment Error Fragments Total number of packets received that were less than 64 octets in length excluding framing bits but including FCS octets and had either a bad Frame Check Sequence FCS with an integral number of octets FCS Error or a bad FCS with a non integral number of octets Alignment Error Discarded Frames Total number of inbound packets which were chosen to be discarded even though no errors had been detected Filtered Frames 6 16 Viewing Errors Statistics for a LAN Port Total number of valid frames received which were discarded by the Forwarding Process Vmux 110 Ver 4 0 User s Manual Chapter 6 Performance Management Table 6 9 LAN Errors Statistics Parameters Cont Parameter Possible Values Remarks Total Collisions Total number of collisions on this Ethernet segment Reset Counters Click lt Reset Counters gt to reset the counters of selected port to O Close Click lt Close gt to close the dialog box Poll Click lt Poll gt to update the information displayed in the dialog box 6 10 Viewing Frame Sizes
56. ab Vmux 110 Ver 4 0 Setting the Operational Parameters 3 23 Chapter 3 Configuration Management Parameter Port Connect Line Type Restore Time Clock Mode User s Manual Table 3 12 Link El Port SW Cfg Tab Parameters Possible Values Remarks Link El Indicates whether the port should be considered in any of the Vmux algorithms No Yes Default No The line type of the interface E1 G 732N E1 CRC G 732NCRC E1 MF G 732S E1 CRC MF G 732SCRC Unframed Default E1 G 732N The time required to restore normal service after the end of a loss of synchronization condition FAST TR 62411 CCITT G 732 Default FAST Note This parameter is disabled when the Line Type is set to Unframed Defines the clock operation mode of the interface LBT loop back timing Internal LBT from Channel Default LBT Interface Type Interface type DSU LTU Default DSU Line Impedance Unbalanced 75 Ohm Balanced 120 Ohm Default Balanced Idle Code hex Hexadecimal code transmitted to fill idle unused time slots in frames transmitted through the selected port 00 FF Default FF Note The following values are not allowed OH 8H 10H 12H 21H 24H 42H 49H 84H 92H Fragmentation Bytes 200 610 1550 Default 610 HDLC Mode Transparent Cisco Bridged ETH Default Transparent Loop Detect Enables disables Loop Detection on the TDM Uplink Disable Enable Default
57. age Tools Config Window Help alslaja Ss Eleele 9 21 Al ne 7 Elala elelelNlalzlel O EEE Root Subnet B x vmux 172 17 158 11 172 17 158 9 172 17 158 14 17214715811 172 17 158 9 1721715814 IE Event History 172 17 158 14 Any Priority Minor 67 24 2006 11 21 51 172 17 158 14 alarmsTrap 1 alrBufDescription DisplayS a 67 24 2666 11 32 13 172 17 158 14 Object Changed by Administrator at 172 18 Trend Event Menu For Help press F1 localhost Administrator Supervisor Figure 4 5 SNMPc Management Console with 3 Nodes Configuring the Nodes for Management Before you can configure the circuits in RADview SC Vmux for each device you must first e Define the Manager List e Read the Configuration to synchronize the Edit mode with the Agent gt To configure a Vmux node for Management 1 From the SNMPc Management Console map Double click on the device icon to open its Element Manager application 4 8 Configuring the Network Management Station Vmux 110 Ver 4 0 User s Manual Chapter 4 Configuring a Typical Application fg4 1 172 17 158 11 Connected Configuration Fault Diagnostics Statistics Window Options Help 9 95 TST ALM PWRI PWR2 mux 2100 o Qo Nen a Loc REM Loc REM 3 Loc REM a RAD 2 o E VC 2E1 1 2 a EI B VCA ZE1 1 2 ACT LINK 4 He z Loc REM ETH E1 CONTROL ETH VWC 2E1 1 2 2100
58. aiting Displayed while the RADview station waits more than a few seconds for the network element response but less than the time out time Interrupted When all attempts to communicate with network element failed time out or when the response was an SNMP error Ready Common Dialog Buttons Displayed after the process has been successfully completed Function buttons located in a sub window or dialog box each initiate the execution of an operation The most common buttons and their respective functions are listed in the following table Button Set Table 2 4 Common Dialog Buttons Function Confirm and activate the selections made in the dialog box and close the box Apply Confirm and activate the selections made in the dialog box without closing the box Cancel Cancel the selections made in the dialog box and close the box Close Close the dialog box without any other effect OK Confirm the message displayed in an information box and close the box Add Open a new dialog box that is used to add a new item to the list or table displayed in the dialog box Change Open a new dialog box that is used to change an item selected in the list or table displayed in the dialog box Delete Delete a selected item from the list or table displayed in the dialog box Refresh Vmux 110 Ver 4 0 Poll the managed unit to retrieve again the information needed to d
59. al site and the device at each remote site Launching RADview SC Vmux RADview SC Vmux the RADview Service Center is a graphical tool for managing Vmux network elements nodes and creating bundles between them Before you can add Sites and Element Nodes or create bundles you must first launch the RADview Service Center gt To launch the RADview Service Center 1 From the Windows Start menu select All Programs gt Network Manager gt Service Center gt SC VMUX The Vmux Service Center application window appears and opens the User Log In dialog box P User Log In A xi User Name Password coe User is not logged in Figure 4 7 Typical Application User Log In Dialog Box 2 Enter your User Name and Password for example root and root and click OK You are now logged in to the Vmux Service Center application 4 10 Creating Bundles Vmux 110 Ver 4 0 User s Manual Chapter 4 Configuring a Typical Application Adding Sites Sites are containers that represent geographical groups of network elements devices or element nodes Before you can add network elements nodes to the Service Center you must first create sites to contain those elements gt To create a new site 1 From the Vmux Service Center Configuration menu select Add Site 2 Type the name o f the site Site A 3 Click Set The newly created site appears on the Service Center map 4 Repeat this procedure for the remaini
60. alking or not Echo Return Loss ERL is the power difference in dB between the far end signal and the echo returned This parameter exists in version 4 0 and higher OK Click lt OK gt to close the dialog box Reading Uploading the Agent Configuration Note gt Note The Read command uploads the current Agent configuration to the Edit configuration The Read command Is only available when there is communication with the Agent To upload the configuration from the Agent 1 In Edit mode only select the device 2 From the Configuration menu select Read 3 Click lt OK gt to upload the current Agent configuration automatically The configuration upload commences immediately No additional user confirmation Is requested The Read Configuration dialog box remains open while the data is uploading A Progress Bar illustrates the upload progress 3 58 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management E 1 172 17 158 14 Read Config x Description Last Update S Date 09 07 2006 Time 13 07 54 By 172 17 150 43 Reading operation will replace Edit Configuration Cancel A ee Figure 3 33 Read Configuration Dialog Box Table 3 32 Read Configuration Parameters Parameter Possible Values Remarks Description Brief description of each agent configuration in the RADview database Last Update Date Date of the
61. alog box Vmux 110 Ver 4 0 Additional Tasks 3 47 Chapter 3 Configuration Management User s Manual SW Cfg 2 Tab 4 1 172 17 158 48 Bundle Connection Details aiei Galler ID Tx Delay msec Figure 3 28 Bundle Connection Details SW Cfg 2 Dialog Box 3 48 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Table 3 27 Bundle Connection Details SW Cfg 2 Connection Parameters Parameter Bundle No Auto FAX Mode FAX Rate Kbps Assigned to FXS Port s Destination Type Modem Max VBD Modem Calls Max Relay Modem Calls Custom Tone Detection Custom Tone Frequency Hz Echo Canceller Coding Law Transparent Jitter Buffer 10 msec Caller ID Tx Delay msec Vmux 110 Ver 4 0 Possible Values Remarks 1 12 Checked Unchecked Not Connected 4 8 9 6 14 4 VBD FAX Default 14 4 Note When Auto FAX Mode is Unchecked this parameter is set to Not Connected 1 4 or 1 8 Note Multiple values may appear separated by commas This parameter is enabled for FXS bundles only PBX Phone Note This parameter enabled for FXS bundles only Disable Voice Band Data Relay Maximum number of voice band data VBD modem calls for this bundle Channel E1 1 31 Channel T1 1 24 Analog Voice 1 4 or 1 8 Note This parameter exists in version 4 0 and higher Maximum number of relay modem calls for this bundle Channel E1 1 62 Channel T1
62. alog box A confirmation dialog box appears 4 Click lt OK gt to save the changed values and return to the VLAN Table dialog box Removing an Entry from the VLAN Table To remove an entry from the VLAN table 1 Select an entry from the VLAN Table 2 Click lt Remove gt Configuring FXS Timeouts and Cadences Note The Timeouts amp Cadences command enables you to configure timeout and cadence values for a specific FXS port The ringer cadences determine the lengths of the ring tones and the silences in between Use the FXS Timeouts and Cadences dialog box to configure the on off timing characteristics of the ring signal as well as the ring and flash timeouts to match the local standards or to provide a custom ring signal for the line The Timeouts amp Cadences option Is available only when the device includes FXS ports gt To configure FXS Timeouts amp Cadences values 1 In Agent mode for viewing or Edit mode for setting select the device 3 16 Setting the Operational Parameters Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management 2 From the Configuration menu select Analog Voice gt Timeouts amp Cadences 3 Configure the desired parameters and click lt Set gt gag E 1 172 17 158 49 FXS Timeouts and Cadences Figure 3 11 FXS Timeouts and Cadences Dialog Box Vmux 110 Ver 4 0 Setting the Operational Parameters 3 17 Chapter 3 Configuration Management User s Man
63. alue exists in version 4 0 an higher Off On Default On Note This parameter exists in version 4 0 and higher Click lt Close gt to close the dialog box Click lt Refresh gt to refresh the data displayed in the dialog box 3 50 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management SW Cfg 3 Tab E 1 172 18 170 123 Bundle Connection Details VLAN ID Priority Tag Figure 3 29 Bundle Connection Details SW Cfg 3 Dialog Box Vmux 110 Ver 4 0 Additional Tasks 3 51 Chapter 3 Configuration Management User s Manual Table 3 28 Bundle Connection Details SW Cfg 3 Connection Parameters Parameter Possible Values Remarks Bundle No 1 12 Dest IP 0 0 0 0 255 255 255 255 VLAN Tagging Tag Untag VLAN ID 26 4094 Note This parameter is disabled when VLAN Tagging is set to Untag Priority Tag 0 7 Note This parameter is disabled when VLAN Tagging is set to Untag MFCR2 MFCR2 Enable Disable Minimum Pulse Width msec Minimum pulse width of the MF tone to be detected and relayed 45 300 Note This parameter is enabled only when MFCR2 is enabled This parameter is disabled for FXS FXO EEM bundles Minimum Power Level dBm Minimum power level of the MF tone to be detected and relayed 1 35 Note This parameter is enabled only when MFCR2 is enabled This parameter is disabled for FXS FXO EEM bundles Close Click lt Close gt
64. ames from 65 to 127 bytes 128 255 bytes Total number of frames from 128 to 255 bytes 256 511 bytes Total number of frames from 256 to 511 bytes 512 1023 bytes Total number of frames from 512 to 1023 bytes 1024 Max bytes Total number of frames from 1024 to 1518 bytes Close Click lt Close gt to close the dialog box Poll Click lt Poll gt to update the information displayed in the dialog box Reset Counters 6 18 Viewing Frame Sizes Statistics for a LAN Port Click lt Reset Counters gt to reset the counters Vmux 110 Ver 4 0 User s Manual Chapter 6 Performance Management 6 11 Viewing Statistics for an E1 T1 or Serial Port Link Use the Link Statistics command to view detailed statistics for a link To view statistics for a link 1 In Agent mode select the serial Link E1 or Link T1 port 2 From the Statistics menu select Link Statistics gag 4 1 172 17 158 49 Link Statistics Legend Wrx Octets WR Error Frames IR Discarded Frames IT Octets 3 45 30 3 46 00 3 46 30 3 47 00 3 47 30 Tx Error Frames Time I Tx Discarded Frames For a different View click on the Legend Figure 6 12 Link Statistics Vmux 110 Ver 4 0 Viewing Statistics for an E1 T1 or Serial Port Link 6 19 Chapter 6 Performance Management Parameter Port User s Manual Table 6 11 Link Statistics Possible Values Remarks Serial Link Link E
65. an E1 T1 or Serial Port Link eeeeeeeeeeeeeeeeeeeteteeeeeeeeeeees 6 19 Chapter 7 Fault Management 7 1 Monitoring Object Status cece cece cece teeter eee nese eae etree saan ee eeaaaeeeeaaaaeeeeeaaaeeeeeaaaees 7 1 Viewing All Active Al rms cccccceeecneeeeee eee ee ress eee eee eeaea eee eeaaeeeeeeaaaeeeeeaaeeeeeeaaeneeeeeaaes Fel Viewing System Level Active Alarms cceceeeeeeeeeeeeeaeeeeeeeeeeeeeeaaeeeeesaaeeeeesaaeeeeeeaaes 7 3 Viewing IP Bundles Active Alarms ccccecccceeeeeeeeeeeeeeeae nese eeaeeeeeeeaeaeeeeesaaeeeeeeaaeeeesaaes 7 5 IP Bundle Active AlarmS cceeceeceeceeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeteeeeteeeeees 7 6 All Bundles Active Alarm LiSt ccccececeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeteeeeeeeneegs T7 Bundle Active Alar Mi LISt iice deceeediv wees canes cecdeececesdanevagedsabvteatsestoedeadeegessawessachecdavedovdeathsethinedves 7 9 Clearing the System Level Active Alarm Buffer 0cceeccteeeeeeeeeeeeeeeeaeeeeeeeaaeeeeeeaaaes 7 9 Clearing All Levels of the Active Alarm BUffel ccccececceeeeeeeeeeeeeeeeaeeeeeeeeaeeeeeeeaaees 7 10 Configuring Alarm Attributes 0 cece ceeeeeee eee cee terse ae eeeeeeaeeeeeeeaaaaeeeeeaaaeeeesaeaeeeeeaaees 7 10 Configuring Alarm Reports ccceeceeeeeeeeeceeaeeeeeeeaeeeeeecaaaeeeesaaaaeeeseaaaeeeseaaaeeeeaaaaes 7 15 Viewing Sanity Check Errors ccccee
66. at there is no manager Set Click lt Set gt to send new values to the Agent Cancel Click lt Cancel gt to cancel the selections made in the dialog box and close the box Refresh Click lt Refresh gt to refresh the data in the Manager List dialog box 3 8 Setting the System Parameters Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management 3 2 Setting the Operational Parameters Configuring Signaling Profile Parameters Note The Signaling Profile command enables you to view or configure the system s signaling profiles If you are using CAS signaling you must configure the Vmux 110 signaling system to make it compatible with the signaling method used by the PBXs connected to the voice channel E1 T1 port The management software allows you to manipulate the ABCD signaling bits and methods of representation of the idle code and out of service signals generated by the PBXs Signaling conversion is used to connect to PBXs that use different signaling formats You can store up to five signaling profiles Vmux 110 uses only one of them at a time The Signaling Profile menu only exists for devices that feature Channel El or Channel T1 ports e A signaling profile translates bits from the network side to the user side e Signaling profile configuration is available only for units operating with CAS signaling A signaling profile is comprised of 6 parameters or nibbles Each parameter is composed of three Octe
67. au ie Figure 3 2 Port User Info Dialog Box Table 3 2 Port User Info Parameters Parameter Possible Values Remarks Port For ETH port ETH NET ETH USER For Link E1 port Link E1 For Link T1 port Link T1 For Channel E1 port Channel E1 For Channel T1 port ChannelT1 For FXS port FXS 1 FXS 8 For FXO port FXO 1 FXO 8 For E amp M port E amp M 1 E amp M 8 For Serial Link port Serial Link User Name User supplied name whose maximum length is 15 characters User Info User supplied information whose maximum length is 70 characters Set Click lt Set gt to send new values to the agent Cancel Click lt Cancel gt to cancel the selections made in the dialog box and close the box Configuring System Parameters The System Parameters command enables you to view and set major system parameters for the Vmux 110 device You can configure parameters such as whether the device contains an E1 or T1 port and which port should be used as the connect through or main link port The router function is not supported in this version of RADview gt To view and set system parameters 1 In Agent mode for viewing or Edit mode for setting select the device 2 From the Configuration menu select System Parameters 3 Configure the desired parameters and click lt Set gt 3 4 Setting the System Parameters Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Note come configuration select
68. ault Menu Table 7 12 Port Management Options Fault Menu Tasks Location in Mode Path in RADview User s Manual Displaying the Alarms for a Port Chapter 7 Agent Fault Alarms Display Clearing the Alarms for a Port Chapter 7 Agent Fault Alarms Clear 2 14 Using the Graphical User Interface Vmux 110 Ver 4 0 User s Manual Chapter 2 Installation and Operation Port Level Statistics Menu Statistics are only available from Agent mode Table 2 13 Port Management Options Statistics Menu Tasks Location in Mode User s Manual Setting the Polling Interval Chapter 6 Agent Path in RADview Statistics Polling Interval Viewing Current Statistics for an E1 T1 Port Chapter 6 Agent Statistics Current Viewing Intervals Statistics for an E1 T1 Port Chapter 6 Agent Statistics Intervals Viewing Data Stream Statistics for a Channel E1 T1 Port Chapter 5 Agent Statistics Data Stream Viewing Receive Statistics for a LAN Port Chapter 6 Agent Statistics wLan Statistics Rx Frame Types Vmux 110 Version 1 1 or greater Viewing Transmit Statistics for a LAN Port Chapter 6 Agent Statistics wLan Statistics wTx Frame Types Vmux 110 Version 1 1 or greater Viewing Error Statistics for a LAN Port Chapter 6 Agent Statistics wLan Statistics Errors Vmux 110 Version 1 1 or greater Viewing Frame Size Statistics for a LAN Port Chapter 6 Agent Statistics Lan Statistics wFrame Sizes Vmux 11
69. bars colored bars to the right of the device ports Using the Graphical User Interface 2 5 Chapter 2 Installation and Operation User s Manual Note Vmux 110 is managed by selecting an object and then selecting the desired function from the menus In many cases this will open a sub window or dialog box allowing further selection and manipulation Menus vary according to the hardware configuration and the selected mode and selected object Unavailable menu options either don t appear at all or are displayed in gray text and cannot be selected Edit and Agent Modes gt gt The Element Manager window contains two Vmux 110 images one above the other The two images provide two configuration modes e Edit mode the upper image modifies the temporary configuration stored at the Network Management Station e Agent mode the lower image configures the agent located within the physical Vmux 110 device the active configuration To select Edit Mode e Inthe Element Manager window click the top image To select Agent Mode e Inthe Element Manager window click the bottom image When Agent mode is selected the focus is on the configuration of the actual physical Vmux 110 the active configuration Displaying the Agent Mode View LEDs Note The Agent View command enables you to display or hide the Agent mode view To display or hide the Agent Mode View 1 Select the device 2 From the Window menu select A
70. bility Interface Type DSU CSU Default DSU Line Length feet Length of the cable connecting the T1 port and the network entry point This parameter affects the transmit signal mask required to meet DSX 1 requirements as specified by AT amp T CB 119 or operation requirements of FCC Rules Part 68A 0 133 134 266 267 399 400 533 534 655 Default 0 133 Disabled when Interface Type is set to CSU RX Sensitivity dBm Low 15 dBm High 36 dBm Default Low Disabled when Interface Type is set to DSU TX Gain level dBm The selected attenuation value brings your signal level closer to the expected repeater signal level on the cable O 7 5 15 0 22 5 Default O Disabled when Interface Type is set to DSU Idle Code hex Hexadecimal code transmitted to fill idle unused time slots in frames transmitted through the selected port 00 FF Default FF Note The following values are not allowed OH 8H 10H 12H 21H 24H 42H 49H 84H 92H Fragmentation Bytes 3 26 Setting the Operational Parameters 200 610 1550 Default 610 Vmux 110 Ver 4 0 User s Manual Parameter HDLC Mode Loop Detect Chapter 3 Configuration Management Table 3 13 Link T1 SW Cfg Tab Parameters Cont Possible Values Remarks Transparent Cisco Bridged ETH Default Transparent Enables disables Loop Detection on the TDM Uplink Disable Enable Default Disable Note This parameter
71. bnet mask and default gateway values according to the parameters in the following table Table 4 1 Typical Application Host IP Settings Site Device Type IP Address Subnet Mask Gateway A Vmux 2100 172 17 158 11 255 255 255 0 172 17 158 1 B Vmux 210 172 17 158 9 255 255 255 0 172 17 158 1 C Vmux 110 172 17 158 14 255 255 255 0 172 17 158 1 Note f they are enabled you must first disable the router and DHCP in order to manually configure the host IP settings of Vmux 110 and 210 Vmux 2100 does not contain a router 3 Enter the SNMP values for read write and trap communities according to the parameters in the following table Table 4 2 Typical Application SNMP Settings Read Community Write Community Trap public Private Public 4 Save the changes to the configuration database by pressing Shift 2 Configuring the Manager List 1 Display the Manager List menu Configuration gt System gt Management gt Manager List 2 Set the manager IP Address to 172 17 158 12 If your Network Management Station NMS Manager has a different IP address substitute the correct IP address of your NMS Note If your Network Management Station NMS Manager has a different IP address substitute the correct IP address of your NMS 3 Save the changes to the configuration database by pressing Shift 2 Vmux 110 Ver 4 0 Configuring the Vmux Units for Management 4 3 Chapter 4 Configuring a Typical Application Us
72. cific severity level ALM LED No Report Event Minor Major Device Alarm LED warning light is On if the severity level of any current active alarm is equal to or higher than the severity level selected here Alarm Off Severity Trap No Report Event Minor Major Defines whether traps for all alarms should be reported or only from a specific severity level Trap severity should be set to a level equal to or higher than Buffer severity Buffer No Report Event Minor Major Defines whether information about all alarms should be reported or only from a specific severity level ALM LED NA Set Click lt Set gt to save changes to Alarm Report parameters Cancel Click lt Cancel gt to close the Alarm Report dialog box without saving changes Note e f No Report Is selected there will be no report data no matter what the alarm severity actually Is e To prevent the Alarm ALM LED from lighting during an event set the ALM LED Alarm On Severity to Minor or to Major This configuration also causes a lighted ALM LED to extinguish after the problem Is fixed Viewing Sanity Check Errors 7 14 Vmux 110 records Sanity Check Errors which flag inconsistencies in the device database You can use the Sanity Check Errors command to view these critical errors so that you can correct them gt To view sanity check errors 1 In Edit mode only select the device 2 From the Fault menu select Sanity Check Errors or Fr
73. configuration Setting the Operational Parameters 3 19 Chapter 3 Configuration Management User s Manual General Port Information 4 1 172 17 158 14 Port Information Figure 3 12 Port Information Info Tab 3 20 Setting the Operational Parameters Vmux 110 Ver 4 0 User s Manual Parameter Port Port Type Operational Status Alarm Status not available for Analog Voice port Interface Desc Chapter 3 Configuration Management Table 3 10 Port Information Info Tab Parameters Possible Values Remarks For ETH port ETH NET ETH USER For El port Link E1 For T1 port Link T1 For Channel E1 port Channel E1 For Channel T1 port Channel T1 For Analog Voice port FXS 1 FXS 8 FXO 1 FXO 8 E amp M 1 E amp M 8 For Serial Link port Serial Link Up Down In Test In Test is not available for Serial ports Off Event Minor Major Warning Critical A description of the interface Close Click lt Close gt to close the Port Information dialog box Refresh Vmux 110 Ver 4 0 Click lt Refresh gt to refresh the data in the Port Information dialog box ETH Port Software Configuration Port ETH NET Physical Address 00 20 D2 22 EA 1E Auto Negotiation IV Max Capability Advertised 100Base TX Full Duplex Default Type s OBASE T Hal Duplex Input Rate Limit Kbps Disable Close Refresh Get successful E Figure 3 13 ETH Port SW Cfg
74. create bundles circuits 4 1 Configuring the Vmux Units for Management The recommended configuration procedure is similar for all three Vmux units except that each unit should be assigned a unique IP address The configuration for each Vmux device includes the following steps e Connect an ASCII terminal to Vmux e Log in as Superuser su e Configure the host IP settings e Save the configuration e Configure the SNMP management settings e Save the configuration Note You must save the selected values at each screen by pressing Shift 2 to update the Vmux 110 configuration database If the database s not updated Vmux 110 discards the new user settings when it is reset You can save selected values at any stage of the configuration procedure Connecting an ASCII Terminal and Logging in 1 Configure an ASCII terminal with the following settings One start bit Eight data bits No parity One stop bit No flow control VT100 emulation 2 Connect an ASCII terminal to the unit s Control port 3 Press lt Enter gt several times to allow the unit to detect the rate 4 Initiate the control session by entering the user name su and password 4 2 Configuring the Vmux Units for Management Vmux 110 Ver 4 0 User s Manual Chapter 4 Configuring a Typical Application Configuring the Host IP Settings 1 Display the Host IP menu Configuration gt System gt Management gt Host IP 2 Enter the IP address su
75. ctive Alarm List Dialog Box Vmux 110 Ver 4 0 Monitoring Object Status 7 7 Chapter 7 Fault Management User s Manual Table 7 4 All Bundles Active Alarm List Parameters Parameter Possible Values Remarks Code Alarm code Bundle No Index number of the bundle Description Description of the alarm Severity No Report Event Minor Major Warning Critical State On Off Mask Mask None Counter Number of times this alarm has been triggered since the last time the system was restarted or the alarm was cleared Clear Click lt Clear gt to clear a selected entry from the All IP Bundles Active Alarm list This button is disabled if the table is empty Save to File Click lt Save to File gt to save the All IP Bundles Active Alarm List The Save dialog box appears In the File Name field enter the name of the file In the File of type field select Acrobat pdf or HTML htm Click Save This button is disabled if the table is empty Print Click lt Print gt to print the All IP Bundles Active Alarm List This button is disabled if the table is empty Close Click lt Close gt to close the All IP Bundles Active Alarm List dialog box Refresh Click lt Refresh gt to update the All IP Bundles Active Alarm List 7 8 Monitoring Object Status Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management Bundle Active Alarm List gag 4 1 172 17 158 49 Bundle Active
76. d HR Frames Minx Bytes Wrx Discards rx Errors HTx Frames IT Bytes Ty Discards 10 29 00 10 30 00 10 31 00 10 32 00 10 33 00 Time For a different View click on the Legend Figure 6 7 Data Stream Statistics Dialog Box Viewing Data Stream Statistics for a Channel E1 T1 Port 6 11 Chapter 6 Performance Management User s Manual Parameter Port Table 6 6 Data Stream Statistics Parameters Possible Values Remarks Channel E1 Channel T1 Data Stream User selection from Data Stream dialog box Running Time The system up time i e the time in hundredths of a second since the network management portion of the system was last re initialized Format DD days HH MM SS Counters Rx Frames Number of frames received Bytes Number of bytes received Discarded Frames Number of discarded frames received Error Frames Number of error frames received Counters Tx Frames Number of frames sent Bytes Number of bytes sent Discarded Frames Number of discarded frames sent Poll Click lt Poll gt to update the information displayed in the dialog box Close gt Click lt Close gt to close the dialog box 6 7 Viewing Receive Frame Types Statistics for a LAN Port The Rx Frame Types command enables you to view Ethernet port receive statistics To view receive statistics for an Ethernet port 1 In Agent mode only select the Ethernet port 2 Fr
77. dditional Tasks Priority of traffic from this IP Bundle over the network Routine Priority Immediate Flash Flash Override CRITIC ECP Inter network ctrl Network Control Default Routine Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Table 3 26 Bundle Connection Details SW Cfg 1 Connection Parameters Cont Parameter Type of Service Possible Values Remarks Type of service for traffic from this IP Bundle Normal High Reliability High Throughput High Throughput Hi Reliability Low Delay Low Delay High Reliability Low Delay High Throughput Low Delay High Throughput High Reliability Default Normal Voice Coding Encoding type and transmission rate for voice traffic through this IP Bundle G7231 6 4 Kbps G7231 5 3 Kbps G729A 8 Kbps G711 A Law G711 u_Law Default G7231 6 4 Kbps Note In the CLI ASCII terminal this parameter is called Coder Rate MFC Spoofing Enable Disable Note This parameter is only visible for E1 T1 bundles with MFCR2 enabled Tone Ack Interval msec 60 400 in steps of 20 Note This parameter is only visible for E1 T1 bundles with MFCR2 and MFC Spoofing enabled Connectivity Packet Connectivity Mode Ping OAM Default Ping Packet Frequency sec 1 60 Default 60 Timeout Cycles 2 5 Default 3 Close Click lt Close gt to close the dialog box Refresh Click lt Refresh gt to refresh the data displayed in the di
78. ea 4 2 Connecting an ASCII Terminal and Logging in ee cece eee eeeeeeee eee eeeeeeeeeeeeeeeeaaeeeeeeaaaeees 4 2 Configuring the Host IP SCttingS cccceeeeeeeeeeee eae eee eee eae eeeeeeaaaeeeesaaeeeesaaaeeeeeaaaees 4 3 Configuring the Manager List 0 ceececceeeeeeeeee tees eaters eee aeeeee saan eeeeeaeeeeesaaeeeeesaaaeeeees 4 3 4 2 Connecting the Vmux Units to the Network Management Station c eeeeeeeeeeeees 4 4 4 3 Configuring the Network Management Station 0 cccccceeeeee ee eeeeeeeeaeeeeeeeaaeeeeeeaaeeeeeeed 4 4 Launching the SNMPc Management Console ccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeesesaaaeees 4 4 Creating the Network NOS ccceeeeeeeeee eee ee eee e saat cess aaa eee eeaaeeeeeesaaaeeeesaeaeeeesaaeees 4 5 Configuring the Nodes for Management cccceeececeeeeeeeaeeeeeeeaeeeeeeeaaaeeeesaeneeeesaaaeees 4 8 4 4 Cheating BUNGE Sasss iera aaa aa a aaa dues enue tne saeepeeebvaeettecvean hs 4 10 Launching RADview SC VMUKX sy deunncedisaavenisscodidixiiascavemhaninatdsaddoians obseevecbabuuaestbsd 4 10 AC GING Sites cc ise cdieesds geecdin ded ievecdewehane pha deccdinvisens ean bbeeaue badee iad veeent eee baceadiabesnuebia eee 4 11 Adding Element Nodes to the Sites 0 ccceeeeeeeeeeee eee eeeee eee eeeeeeeaaeeeeseaaeeeeeesaaeeeeeeea 4 11 Creating BUNCIOS ccc ee ceeceeeee cece eee ee eee aetna eee cates ea caa eee seca eee seaaa eee seaaaeeeseaaaeeeeaaaaes 4 13 Chap
79. eeeeeeeeee eee aeeeeeeeaae eee seaaaeeeseaaaeeeseeaaeeeseeaaeeeeeaey 7 14 Displaying the All Buffer Alarms List cceeecceeeee eee eeeeee eae tees saan eee eeaaeeeeeeaeeeeeenaa 7 16 Displaying the New Buffer Alarms LiSt ccceeeceeeeeeeeeee eee eeeeeaaeeeeeeeaaeeeeeeaaeeeeeeeaa 7 17 Displaying the Port Active Alarm List cceeceeeeeeeeeeeeeee eae eeeeeeaeeeeeeaaeeeeeeaeeeeeeaea 7 18 Clearing the Port Active Alarm Buffer cccceceeeeeeeeeeeeeeeeeeeeaeeeeeesaaeeeeesaeeeeeesaaaes 7 19 7 2 R nning Loopback TeStSsaczscesesehee ccen antaa iaa a R Ea EES 7 19 Index Vmux 110 Ver 4 0 iii Table of Contents User s Manual iv Vmux 110 Ver 4 0 Note Interfaces Vmux 110 Ver 4 0 Chapter 1 Introduction This chapter provides an overview of the Vmux 110 device and the RADview Service Center Vmux 110 user interface 1 1 Overview of the Vmux 110 Device Vmux 110 is a voice trunking gateway that enables digital E1 Tlor multiple FXS FXO E amp M analog voice channels to be compressed and extended over a serial E1 T1 or 10 100Base T uplink Vmux 110 implements G 723 1 G 729 A G 711 compression and TDMoIP or AAL20MPLS multiplexing algorithms to send the voice channels over the IP E1 T1 or n x 64 kbps network Vmux 110 utilizes voice activity detection silence suppression echo cancellation and other techniques to improve voice quality and bandwidth utilization The gateway detects generates and relays DTMF s
80. eived Rx HDLC Frames Number of HDLC frames received Counters Tx Tx Frames on Number of transmitted frames in the interval since the system was last re initialized Interval Tx Max Size Number of maximum sized frames transmitted Frames Tx Signaling Number of signaling frames transmitted Frames Note For FXS ports only Tx Voice Frames Number of voice frames transmitted Tx HDLC Frames Number of HDLC frames transmitted Frame Tracking Duplicated Number of packets dropped due to being duplicated A duplicated packet is a packet Dropped that has the same sequence number as a previously received packet Missing Number of packets that are missing A missing packet is a packet that was expected according to the current sequence number but was never received Longest Series of Missing Longest series of consecutive missing sequential numbers Missing sequential numbers represent missing packets that were expected to be received successively Close Click lt Close gt to close the Bundle Statistics dialog box Refresh Click lt Refresh gt to update the Bundle Statistics Reset Counters Vmux 110 Ver 4 0 Click lt Reset Counters gt to reset the Bundle Statistics Counters for the displayed bundle to 0 Viewing Bundle Connection Statistics 6 5 Chapter 6 Performance Management User s Manual 6 4 Viewing Current Statistics for an E1 T1 Port Use the C
81. ent 4 Enter the attributes of the new alarm entry 5 Click lt Set Add Alarm Attributes Alarm fi DB CONTROL WAS TAKEN BY TERM MMI m Port CJ i Bundle INA v Mask Yes Figure 7 7 Add Alarm Attributes Dialog Box Configuring Alarm Reports The Configuration gt Reports command enables you to set the severity of each type of alarm and thereby define when alarms are triggered or cleared This determines what information will be saved in the Report files gt To configure Alarm Reports 1 In Agent mode only select the device 2 From the Fault menu select Alarms gt Configuration gt Report A 1 172 17 158 44 8FXS Alarm Report E xi Alarm On Severity Alarm Off Severity Trap Waring M waming z Buffer Jwarning fwaming x ALM LED Jwaming gt NA Set Cancel Get successful jm Figure 7 8 Alarm Report Dialog Box Vmux 110 Ver 4 0 Monitoring Object Status 7 13 Chapter 7 Fault Management User s Manual Parameter Alarm On Severity Table 7 6 Alarm Report Parameters Possible Values Remarks Trap No Report Event Minor Major Defines whether traps for all alarms should be reported or only from a specific severity level Trap severity should be set to a level equal to or higher than Buffer severity Buffer No Report Event Minor Major Defines whether information about all alarms should be reported or only from a spe
82. ent configuration to Edit mode 3 58 Agent Configuration mode see Agent mode 2 6 Agent mode introduction 2 6 port level operations 2 14 system level operations 2 10 Agent mode dialogs Bundle Statistics 6 4 Current Statistics 6 6 Date amp Time Setup 3 7 Intervals Statistics 6 8 LAN Receive 6 13 LAN Transmit 6 14 Manager List 3 8 Polling Interval 6 2 Port Information Sw Cfg Analog Voice Port 3 33 Port Information Sw Cfg El port 3 23 3 25 Port Information Sw Cfg ETH port 3 21 Port Information Sw Cfg Serial Link port 3 34 Reset hardware 3 62 System Information 3 2 Agent view toggling 2 6 Agent polling 3 61 Alarm Test Status Indication Bars 2 7 analog voice port viewing status 3 37 Analog Voice Port Status displaying 3 37 Application information 2 10 B Bridge Ports configuring 3 11 Bundle Connection Details Advanced Voice Parameters 3 57 SW Cfg 1 tab 3 45 SW Cfg 2 tab 3 48 SW Cfg 3 tab 3 51 SW Cfg 4 tab 3 53 SW Cfg 5 tab 3 55 Bundle Connection Parameters displaying 3 43 Bundle Statistics dialog Agent mode 6 4 Bundles viewing bundle connection statistics 6 2 viewing system bundles 3 43 Buttons common dialog 2 9 Vmux 110 Ver 4 0 gt Cadence of an FXS port viewing 3 16 Clock setting date and time 3 6 Configuration updating the agent 3 59 uploading from the agent 3 58 Configuration management overview 3 1 Configuration modes 2 6 Configuration resetting 3
83. er ID type used by the DSP for this bundle Bellcore Type 1 V 23 Default Bellcore Type 1 Note Bellcore type Caller ID is the American method V 23 type Caller ID is the European method This parameter is only available when Voice Coding is set to G729A 8 This parameter exists in version 4 0 and higher VBD Rate Kbps The voice band data VBD rate for this bundle 64 in 5 msec Intervals G 711 64 in 10 msec Intervals G 711 32 G 726 24 G 726 Default 64 in 5 msec Intervals G 711 Note This parameter exists in version 4 0 and higher 3 56 Additional Tasks Vmux 110 Ver 4 0 User s Manual Parameter CAS Redundancy Chapter 3 Configuration Management Table 3 30 Bundle Connection Details SW Cfg 5 Connection Parameters Cont Possible Values Remarks Enables or disables CAS signaling redundancy Disable Enable Default Disable Note Enable means that each packet containing CAS signaling will be replicated for redundancy into 3 packets This setting is useful when there are problems with the network This parameter only affects connections that utilize CAS signaling such as E1 MF G 732S or E1 CRC MF G 732SCRC Disable means that no redundancy will exist Only I packet containing CAS will be transmitted This parameter exists in version 3 11 and higher Advanced Voice Click lt Advanced Voice Parameters gt to open the Advanced Voice Parameters Parameters dialog box
84. er s Manual 4 2 Connecting the Vmux Units to the Network Management Station Vmux units can be managed by a Network Management Station NMS that is located on the LAN hub or switch connected to the one of the unit s Ethernet network ETH NET ports Install the physical devices and connect their cables according to the network diagram in Figure 4 1 gt To connect a Vmux unit to the Network Management Station 1 Connect the Network Management Station to the LAN hub or switch 2 Connect one of the Vmux s Ethernet network ETH NET ports to the LAN 4 3 Configuring the Network Management Station Before you can configure the circuits in RADview SC Vmux you must first use the SNMPc Management Console to e Launch the SNMPc Management Console e Create the Vmux nodes e Define the Manager List e Read the Configuration Launching the SNMPc Management Console The SNMPc Management Console is used to create and configure the network nodes so that the devices are available for management in the RADview Service Center Before you can create and manage the network nodes you must first launch the SNMPc Management Console gt To launch the SNMPc Management Console e From the Windows Start menu select All Programs gt Network Manager gt RADview 32 4 4 Configuring the Network Management Station Vmux 110 Ver 4 0 User s Manual Chapter 4 Configuring a Typical Application Z5 SNMPc Management Console me 6 x File Edit Yiew
85. erse Polarity 3rd LSB Nibble representing the REVERSE POLARITY signal 0000 1111 Default 1001 DCBA Note This parameter is enabled for FXS and FXO ports when Pulse Metering is enabled Pulse Metering 6th LSB Nibble representing the PULSE METERING signal 0000 1111 Default 1001 DCBA Note This parameter is disabled when Reverse Polarity is enabled Ringback Disable Enable Default Enable Note This parameter is enabled for FXO ports only Reverse Polarity Disable Enable Default Disable Note This parameter is enabled for FXS and FXO ports when Pulse Metering is disabled Immediate On Hook Detect While Ringing Pulse Metering Enables or disables immediate reaction to On Hook bits from network while ringing Disable Enable Default Disable Note This parameter is enabled for FXS ports only Note The Pulse Metering parameters are disabled grayed out for Vmux 110 3 54 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Table 3 29 Bundle Connection Details SW Cfg 4 Connection Parameters Cont Parameter Possible Values Remarks Enable Enables or disables pulse metering synthesis No Yes Default No Frequency KHZ Frequency of synthesized pulse metering for this bundle 12 16 Default 16 Duration msec Duration of synthesized pulse metering 100 250 Default 150 Close Click lt Close gt to close the dialog box Refresh Cl
86. ersentoenecess 2 13 System Level Window MO NU ccccceccceeeeccceeeeeeeceeeeeeeaeeeeaeeaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaea 2 13 System Level Options Merl cscsssccceccccceeeeaaeeeaaeaaeeaaaeaaaaeaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaea 2 13 P rt Level OPEratlONs siazseccedareetsansenstaw saves ana anatina destousy ad aaa aiea ta 2 14 Port Level Configuration Men cccccceesceeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeteetenegs 2 14 Port Level Diagnostics M NU ti isisciies ieetiodeectdies Gi dete esi a i eE AEE AENEAS 2 14 Port Level Fault Meriti rerien eseve deed aeea nitty iwi adtlaeeede dion 2 14 Port Level Statistics MOMs siccciistageveecictoasd coegiactenes tip ec nae aaia ea Weber eyelet inte 2 15 Configuration Management Setting the System Parameters cceecee cece cece ee eee eee e eee eee ea aaa eeeeaaaaeeeeeaaaeeeesaaaeeeesaaaeees 3 2 Configuring System Information ccceeeeeeeeeeeeee eee eeee saan eee eeaaeeeeeeaaaeeeeesaeeeeeesaaeeees 3 2 Setting Port User INfOrmation eee cece eee ee rree eee ee esse eae aaa aeeeeeeeeeeeaaaaaeneeeeeeeeeaaga 23 Configuring System ParaMetels ccccceeeeeeeeeeeeeeeaeeeeeeeaaeeeeeeaeeeeeeeaeeeeeesseeeeseaaneeeees 3 4 Selecting the Date Format cc ccceeceeeeeee eee ee eee ee eae eee eee aaeeeeas ae age aAa Sa e 3 6 Setting the Date and Time risorsi tnin aaaeaii aani nii aeaiia vi iaeia ins 3 6 Configuring the Manager LiSt
87. etting the System Parameters 3 1 Chapter 3 Configuration Management User s Manual 3 1 Setting the System Parameters Configuring System Information The System Info command enables you to view and set system information for the Vmux 110 device This information is useful for identifying multiple Vmux 110 units and for tracking their locations and administrative contacts gt To view and set system information 1 In Edit mode for viewing or Agent mode for setting select the device 2 From the Configuration menu select System Info 3 Configure the desired parameters and click lt Set gt 4 1 172 17 158 14 System Information Description Vmux 110 HW Version 1 00 SW Version 4 0071 Object ID Ymuxl10 Oo Name mue tt sss SsSSSS Contact fara Location The location of this device S System Up Time 3 days 01 29 56 Number of Interfaces 11 Set Cancel Refresh Get successful gO Figure 3 1 System Information Dialog Box Agent Mode 3 2 Setting the System Parameters Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Table 3 1 System Information Parameters Parameter Possible Values Remarks Description A description of the device including hardware and software versions Object ID The device s SNMP Object ID without the rad prefix Agent mode only Name The name of the device a string of up
88. gent View If the Agent mode view was previously hidden a check mark appears next to the Agent View entry in the menu and the Agent mode view appears If the Agent mode view is already visible the Agent mode view disappears The Window menu is only enabled when there is communication with the Agent The Agent mode front panel of the Vmux 110 includes LED indicators that show the current operating status of the device 7ab e 2 1 describes the indicators Using the Graphical User Interface Vmux 110 Ver 4 0 User s Manual Name ALM red ETH green PWR green Chapter 2 Installation and Operation Table 2 1 Vmux 110 LEDs Function ON Alarm exists OFF No alarm exists ON Link is connected and synchronized OFF Link is not connected ON Device is receiving its Power Supply from PS OFF No power in the device Alarm Test Status Indication Bars Vmux 110 Ver 4 0 Location Front panel Front panel Front panel In addition to the LED indicator colors when there are active alarms or tests the Agent mode front panel of Vmux 110 displays alarm and test status indication bars These short vertical bars are located to the right side of the Vmux 110 device and to the right of each of its ports indicating the locations of the alarms and tests The indication bars display the active alarm status and test status based upon polling and traps The following table describes how to interpret the meaning
89. ick lt Refresh gt to refresh the data displayed in the dialog box SW Cfg 5 Tab 4 1 172 17 158 48 Bundle Connection Deta REE xj SW Cfg 1 SW Cfg 2 sw Cfg3 VAD Method HE 7 Tx Gain dB 0 Rx Gain dB 0 Galler ID Type Bellcore Type 1 VBD Rate Kbps 64 in 5 msec Intervals G 711 GAS Redundancy Disable Advanced Voice Parameters Close Refresh Get successful j Figure 3 31 Bundle Connection Details SW Cfg 5 Dialog Box Vmux 110 Ver 4 0 Additional Tasks 3 55 Chapter 3 Configuration Management User s Manual Table 3 30 Bundle Connection Details SW Cfg 5 Connection Parameters Parameter VAD Method Possible Values Remarks The voice activation detection VAD method Proprietary Internal ITU T Default Proprietary Note Proprietary uses a non standard VAD method based only on power measurement This method Is very sensitive to background noise Internal ITUT uses the standard ITU T method for VAD This method is very robust This parameter exists in version 3 11 and higher Tx Gain dB The transmit gain in dBm 6 6 Default O Note This parameter is disabled for FXS FXO E amp EM bundles In the CLI this parameter is called Volume To Line Rx Gain dB The receive gain in dBm 6 6 Default O Note In the CLI this parameter is called Volume From Line This parameter exists in version 3 11 and higher Caller ID Type The Call
90. ignaling In addition Vmux 110 supports fax relay modem relay and voice band data The built in router supports NAT firewall static and dynamic routing RIP1 and RIP2 To facilitate the integration of new devices into a DHCP IP network the router also supports DHCP client server and relay In this version of RADview the router function is not supported Vmux 110 is managed locally via an ASCII terminal or remotely via Telnet or RADview RAD s SNMP based network management application Vmux 110 includes two Ethernet LAN ports user and network and can be ordered with the following options Voice port options e El voice channel port e T1 voice channel port e 4 FXS voice ports e 4 FXO voice ports e 4 E amp M voice ports e 8 FXS voice ports e 8 FXO voice ports e 8 E amp M voice ports Overview of the Vmux 110 Device 1 1 Chapter 1 Introduction User s Manual Link port options e E11 link e T1 link e Serial V 35 link e Ethernet link 1 2 RADview SC Vmux 110 Overview Vmux 110 includes an SNMP agent that enables full management from the network via SNMP for example by means of RADview network management stations In addition Vmux 110 includes the following additional management capabilities via both out of band and inband communication e Supervision terminal ASCII terminal or a PC running a terminal emulation program connected either directly or through a modem or any other type of full duplex data lin
91. ing a Vmux 110 8 E amp M and a Vmux 210 30 FXS operating opposite a central Vmux 2100 unit over an IP network and contains the following sections e Configuring the Vmux Units for Management e Connecting the Vmux Units to the Management Station e Configuring the Network Management Station e Creating Bundles Circuits Application Figure 4 1 illustrates a typical TDM application in which a Vmux 110 anda Vmux 210 operate opposite a central Vmux 2100 over an IP network Two El trunks are transmitted by the central Vmux 2100 over an IP network to two remote Vmux units 172 17 158 9 Site B amp Ph Central Site 30 x FXS one Site A Vmux 210 oz gt SEI 172 17 158 11 10 100Base T amp i Phone 10 100Base T IP ETH Network Vmux 2100 172 17 158 14 10 100Base T E 172 17 158 12 ce F Vmux 110 E a Site C amp A Cl Phone NMS Figure 4 1 Typical Application with a Vmux 110 and a Vmux 210 opposite a Vmux 2100 Vmux 110 Ver 4 0 Configuring the Vmux Units for Management 4 1 Chapter 4 Configuring a Typical Application User s Manual Configuration Sequence The recommended configuration procedure for this application includes the following steps 1 Configure all three Vmux units for management via an ASCII terminal 2 Install the Vmux units in their locations and connect their cables 3 Using the SNMPc map add the managed elements MEs network nodes 4 Using the RADview Service Center
92. ion Add Circuit ME Selection 3 Select the Source ME and the Destination ME 4 Click Set The Add Circuit dialog box closes and the State 1 dialog box appears State 1 Source amp Destination x rSource ME r Destination ME Site Name v Ste Name stes z ME Name 172 17 158 11 gt ME Name 172 17 158 9 x ME Type Vrux 2100 ME Type Ymux 210 IP Address 172 17 158 11 IP Address 172 17 158 9 Sot wna cl Card Type VC 2E1 Card Type NJA Port 1 amp 2 ba Port 1 30 bd Port Type El Port Type FXS Bundle No fi z Bundle No fe Ne Bundle Name Bundle 1 Bundle Name Bundle 2 Connect Through Ethernet v Description Circuit created 2006 7 9 Comments Back Next gt Finish Cancel Figure 4 12 Typical Application State 1 Dialog Box 5 Click Next 6 Ifa reset warning dialog box appears click OK 4 14 Creating Bundles Vmux 110 Ver 4 0 User s Manual Chapter 4 Configuring a Typical Application State 2 Circuit Parameters Noses ah aes fe os x SW Cfg 1 sw cfg 2 sw cfa3 5w cfa sw cFg5 Circuit Name 7 4 Voice Coding Kbps e7231 6 4 v Connect Yes z MFCR2 Disable v Transport Protocol fromor Compressed Header v MFG Spoofing Disa ble Y Packet Interval msec fso morni an Signaling Type of Service TOS Tone Ack Interval msec fo 4 Precedence Routine v Type of Service Normal v PE
93. ion value brings your signal level closer to the expected repeater signal level on the cable FXS 4 5 FXO 4 5 E amp M 7 5 Default 0 Rx Gain dB FXS 10 5 Default 4 FXO 17 1 Default 4 E amp M 17 2 Default 0 Set Click lt Set gt to save the new values in the dialog box Cancel Vmux 110 Ver 4 0 Click lt Cancel gt to cancel the selections made in the dialog box and close the box Setting the Operational Parameters 3 33 Chapter 3 Configuration Management User s Manual Serial Link Port Software Configuration E 1 172 17 158 14 Port Information xl Transparent Serial Link 2 jo xH 2 io Transparent zd rable H Figure 3 19 Serial Link Port SW Cfg Tab Agent Mode 3 34 Setting the Operational Parameters Vmux 110 Ver 4 0 User s Manual Parameter Port Chapter 3 Configuration Management Table 3 17 Serial Link SW Cfg Tab Parameters Possible Values Remarks Serial Link Interface Type The line type of the interface V 35 X 21 EIA530 EIA530A Default V 35 Connect Indicates whether the port should be considered in any of the VMUX algorithms No Yes Default No Clock Mode DCE DTE Default DCE Rate Kbps 1x64 64 2x64 128 31x64 1984 32x64 2048 Default 1x64 64 Control Signals Ignore Implement only available when Default Ignore Interface type is set to
94. ions 1 2 pre configuration 2 1 setting access authorizations 5 1 Management pre configuration configuring the IP parameters 2 2 configuring the manager list 2 3 connecting a terminal to the control port 2 1 disabling the router 2 2 Management station adding to Manager List 3 7 Manager List adding a manager 3 7 Agent mode 3 8 configuring 3 7 Managing configuration 3 1 Mux Information dialog 3 37 displaying Agent mode 3 36 O Object selecting 2 8 Operational Parameters setting 3 9 Operations port level Agent mode 2 14 system level Agent mode 2 10 Overview 1 2 User s Manual Overview of device 1 1 p Performance Management 6 1 introduction 6 1 Polling Interval dialog Agent mode 6 2 setting 6 2 Polling the agent 3 61 Port analog voice time slot assignments 3 40 configuring analog voice port 3 33 Channel E1 3 27 Channel T1 3 30 Ethernet 3 21 Link El 3 23 Link T1 3 25 serial 3 34 displaying configuration 3 19 link E1 T1 time slot assignments 3 39 selecting 2 8 Port configuration 3 19 Port Configuration copying 3 35 Port Information configuring 3 19 displaying 3 19 general port information 3 20 Port Information Sw Cfg dialog Analog Voice Port Agent mode 3 33 Port Information Sw Cfg dialog E1 port Agent mode 3 23 3 25 Port Information Sw Cfg dialog ETH port Agent mode 3 21 Port Information Sw Cfg dialog Serial Link port Agent mode 3 34 Port level opera
95. ions may produce a second confirmation dialog box to verity the configuration settings f you receive the following error message Cannot change Link Type Link TSA and or Voice Bundles exist Removing them can be done only via the Service Center e norder to remove a Link TSA via the Service Center In the Service Center from the Channel List click lt Remove gt e norder to remove a Voice Bundle via the Service Center In the Service Center from the Circuit List or the Channel Circuit List click lt Remove gt E 1 172 17 158 14 System Parameters me xi Connect Through Serial Link Link Type Ti v Router Enable E Net User Routing Mode Layer 2 Switching ia Default Gateway 0 0 0 0 Figure 3 3 System Parameters Dialog Box Edit Mode Vmux 110 Ver 4 0 Setting the System Parameters 3 5 Chapter 3 Configuration Management Parameter Connect Through User s Manual Table 3 3 System Parameters Possible Values Remarks ETH NET Serial Link Link E1 T1 Default Serial Link Note In the CLI this parameter is called Main Link Link Type E1 T1 Default E1 Router Note The router function is NOT supported in this version of RADview Enable Checked Unchecked Default Unchecked Net User Routing Mode enabled only when Router is Enabled and Connect Through is Serial Link or Link E1 T1 Layer 2 Switching Layer 3 Routing Default Laye
96. isplay the current dialog box This action updates the displayed information Using the Graphical User Interface 2 9 Chapter 2 Installation and Operation Displaying Help User s Manual The Help menu provides convenient access to online help gt To display online help e From the Help menu select User s Manual The online User s Manual appears Displaying the Application Software Information The About Vmux 110 menu displays information about the RADview SC Vmux 110 Element Manager application software such as the version number gt To display the Element Manager software information e From the Help menu select About Vmux 110 The About Vmux 110 dialog box appears System Level Operations The following tables list the RADview tasks available on the system level System Level Configuration Menu Table 2 5 System Management Options Configuration Menu Task Location in User s Mode Path in RADview Manual Viewing Mux Information Chapter 3 Agent Configuration Mux Info Configuring System Information Chapter 3 Both Configuration System Info Configuring System Parameters Chapter 3 Both Configuration wSystem Parameters Selecting the Date Format Chapter 3 Agent Configuration gt Date Format Setting the Date and Time Chapter 3 Agent Configuration Date amp Time Reading Uploading Agent Configuration Chapter 3 Edit Configuration Read Updating Downloading Configuration to the Chapter 3 Edit C
97. ites and Devices Site Name Device Type Device IP Address Site A Vmux 2100 172 17 158 11 Site B Vmux 210 172 17 158 9 Site C Vmux 110 172 17 158 14 4 12 Creating Bundles Vmux 110 Ver 4 0 User s Manual Chapter 4 Configuring a Typical Application When you have added all three devices the Service Center map will contain three sites with one Vmux unit in each site P mux Service Center Ioj xi Configuration Yiew Events Security Statistics Help e il SS aK a e m At least one ME is not responding Figure 4 10 Typical Application Service Center Map with 3 Populated Sites Creating Bundles Bundles are groups of timeslots In order for voice data to pass between the different Vmux devices you must create bundles between each branch site and the central site from Vmux 210 to Vmux 2100 and from Vmux 110 to Vmux 2100 gt To create a bundle between two Vmux devices 1 From the Vmux Service Center map hold down the CTRL key and left click on the Site A 2 Left click Site A and drag to Site B A line appears from Site A as you drag from Site A When you finish dragging the Add Circuit wizard starts Vmux 110 Ver 4 0 Creating Bundles 4 13 Chapter 4 Configuring a Typical Application User s Manual P Add Circuit MEs Selection Source ME Destination ME ME Name SW Version ME Name SW Version 58 11 58 vmux 2100 58 49 7 9 Vmux 210 Figure 4 11 Typical Applicat
98. k This terminal can perform all of the Vmux 110 supervision and configuration functions including preliminary system configuration e Telnet from any host capable of IP communication with Vmux 110 out of band using SLIP or PPP or inband over IP The functions available via the Telnet are similar to those available from a supervisory terminal e Web browsers using ConfiguRAD ConfiguRAD is a user friendly Web based element management system that is embedded in Vmux 110 and provided at no extra cost ConfiguRAD can be accessed from any standard Web browser This manual discusses configuration via RADview RAD s SNMP based network management application for PC or Unix To configure Vmux 110 via ASCII terminal Telnet or Web browser see the Vmux 110 Installation and Operation Manual Overview of the RADview FCAPS Model RADview provides a complete solution for monitoring and controlling Vmux 110 The RADview solutions conform to ITU T Telecommunication Management Network TMN recommendations for SNMP management systems known as the FCAPS model e Fault management detects and correlates faults in network devices isolates faults and initiates recovery actions e Configuration management tracks configuration changes configures installs and distributes software and configuration files over the network e Accounting management collects accounting data and generates network usage reports e Performance management continuousl
99. l field type the Vmux unit s IP Address The Label field defines the name assigned to the node 3 In the Address field type the Vmux unit s IP Address 4 Click the Access tab 4 6 Configuring the Network Management Station Vmux 110 Ver 4 0 User s Manual 5 6 7 8 9 Chapter 4 Configuring a Typical Application Map Object Properties General Access Attributes Dependencies Name Lip er a ee Value ee A Attrib Name Value Read Access Mode SNMP 1 Read Write Access Mode SNMP 1 Read Community public Read Write Community private Trap Community public 3 Engineid lt auto gt Y3 Context Name lt not seb Y3 No Auth Security Name lt not set gt w3 Auth Priv Security Name lt not seb 3 Auth Passwd lt not set gt w3 Priv Passwd lt not set gt Figure 4 4 Map Object Properties Access Tab In the Attrib area click Read Community In the Value field select public In the Attrib area click Read Write Community In the Value field select private In the Attrib area click Trap Community 10 In the Value field select public 11 Click OK The Vmux icon appears on the SNMPc Management Console map 12 Repeat this procedure for the remaining two Vmux devices Vmux 110 Ver 4 0 Configuring the Network Management Station 4 7 Chapter 4 Configuring a Typical Application User s Manual Z5 SNMPc Management Console i E y l xj File Edit Yiew Insert Man
100. last update of each configuration Time Time of the last update of each configuration By IP address of the manager that performed the last update of each configuration 0 0 0 0 255 255 255 255 OK Click lt OK gt to automatically upload the current Agent configuration Cancel Click lt Cancel gt to close the Read Configuration dialog box without uploading the current Agent configuration Abort Click lt Abort gt to stop reading the current Agent configuration Updating Downloading the Configuration to the Agent The Update command downloads a specific Edit Configuration to the VMUX Agent Vmux 110 Ver 4 0 Additional Tasks 3 59 Chapter 3 Configuration Management User s Manual To update the Agent 1 In Edit mode only select the device 2 From the Configuration menu select Update 3 If desired enter a description of the configuration 4 Click lt OK gt to download the selected configuration to the VMUX The Update Configuration dialog box remains open while the data is downloading A Progress Bar illustrates the download progress E 1 172 17 158 14 Update Config ait x Description Update operation will replace Agent s Configuration OK Cancel Abort Figure 3 34 Update Configuration Dialog Box Table 3 33 Update Configuration Parameters Parameter Possible Values Remarks Description Brief description of the selected Edit Configuration a string of up to 19 character
101. le Remove Click lt Remove gt to remove an entry from the VLAN table Apply Click lt Apply gt to save new parameter values and add an entry to the VLAN table in Add VLAN table only Set Click lt Set gt to save new parameter values for an entry in the VLAN table in Change VLAN table only Close Click lt Close gt to close the dialog box Vmux 110 Ver 4 0 Adding an Entry to the VLAN Table To add an entry to the VLAN table l 2 In Edit mode in the VLAN Table dialog box click lt Add gt Configure the desired parameters in the Add VLAN dialog box see the following table Click lt Apply gt to save the new values Click lt Close gt to close the Add VLAN dialog box and return to the VLAN Table dialog box Setting the Operational Parameters 3 15 Chapter 3 Configuration Management User s Manual Note gt gt You can add up to ten entries Add LAN i xj VLAN ID fi ETH NET Transparent X ETH USER Transparent Ma Link Mng Forbidden X ai 7 Close l Figure 3 10 Add VLAN Entry Dialog Box Changing an Entry in the VLAN Table To reconfigure an entry in the VLAN table 1 In the VLAN Table dialog box select an entry from the VLAN Table and click lt Change gt 2 Configure the desired parameters in the Change VLAN dialog box see Table 3 8 3 Click lt Set gt to save the new values and return to the VLAN Table di
102. mains green as long as the service is connected If the service is down then the link turns red 4 16 Creating Bundles Vmux 110 Ver 4 0 User s Manual Chapter 4 Configuring a Typical Application P mux Service Center Configuration view Events Security Statistics Help At least one ME is not responding Figure 4 15 Typical Application Service Center Map with One Bundle 11 Repeat this procedure from Step 1 to Step 10 but this time create the bundle from Site A to Site C and use time slots 5 6 and 7 Vmux 110 Ver 4 0 Creating Bundles 4 17 Chapter 4 Configuring a Typical Application User s Manual mux Service Center Configuration View Events Security Statistics Help C3 mal aa e Figure 4 16 Typical Application Service Center Map with 2 Connected Bundles 4 18 Creating Bundles Vmux 110 Ver 4 0 gt Parameter Telnet Chapter 5 Security Management This chapter describes how to manage Vmux 110 security and includes the following sections e Setting Management Access Authorizations e UNIX Users and Permissions 5 1 Setting Management Access Authorizations The Access command allows you to enable or disable management via Telnet Use this command to tighten security or to enable access when necessary To enable or disable Telnet access 1 In Edit mode select the device 2 From the Options menu select Access The Access dialog box appears Error Reference source not found
103. n fae 1 Print Save to File Clear All Close Refresh Ready jm Figure 7 1 Mux All Active Alarm List Dialog Box 7 2 Monitoring Object Status Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management Table 7 1 Mux All Active Alarm List Parameters Parameter Possible Values Remarks Code Alarm code Port Selected port if applicable Description Description of the alarm Severity No Report Event Minor Major Warning Critical State On Off Mask Mask None Counter Number of times this alarm has been triggered since the last time the system was restarted or the alarm was cleared Print Click lt Print gt to print the Mux All Active Alarm List This button is disabled if the table is empty Save to File Click lt Save to File gt to save the Mux All Active Alarm List The Save File dialog box appears In the File Name field enter the name of the file In the File of type field select Acrobat pdf or HTML htm Click Save This button is disabled if the table is empty Clear All Click lt Clear All gt to clear all active alarms of all levels and close the Mux All Active Alarm list This button is disabled if the table is empty Close Click lt Close gt to close the Mux All Active Alarm List dialog box Refresh Click lt Refresh gt to update the Mux All Active Alarm List Viewing System Level Active Alarms Vmux 110 Ver 4 0 The Display gt
104. ndow click the frame surrounding the desired port e When a Vmux device contains more than 4 analog ports for example 8 ports all these ports reside on a single connector Each port within this specific connector is marked with its relative number for example the 8FXS connector has 8 numbers labeled 1 through 8 Select a specific port number by clicking the number of the desired port e The Control port is not selectable Status Indicators At the top of the window the title bar displays lt element name gt lt status gt where status is either Connected or Disconnected according to the current connectivity of the network element to the NMS At the bottom of the Element Manager window there is also a communications status bar Sometimes congestion in the network handling the management traffic causes significant delays during polling transfer of large data tables etc When feasible a progress bar is used to inform the operator of the ongoing process status Otherwise a message is displayed in the status bar at the bottom of the screen according to the following table 2 8 Using the Graphical User Interface Vmux 110 Ver 4 0 User s Manual Message Working Chapter 2 Installation and Operation Table 2 3 Element Manager Status Bar Messages Status Displayed from the moment when a request is sent to the network element Vmux 110 until data is received or a certain time expires around 5 seconds W
105. ng two sites Site B and Site C e ymux Service Center x Configuration View Events Security Statistics Help DME SA aK lt i S a Figure 4 8 Typical Application Service Center Map with 3 Empty Sites Adding Element Nodes to the Sites In order to manage a network element from the Service Center you must first add it to a site as a managed element node gt To add a managed element ME to a site 1 From the Vmux Service Center map Double Click Site A The Site A window appears 2 From the Site A window Configuration menu select Add ME Vmux 110 Ver 4 0 Creating Bundles 4 11 Chapter 4 Configuring a Typical Application User s Manual yadd Managed Element to Site A Available RADview Agent List i TME ie IP Address JU Ym mux mux 110 172 17 158 14 mux 110 172 17 158 13 mux 110 172 17 158 46 mux 110 172 17 158 47 Nmux 110 172 17 158 48 Nmux 210 172 17 158 49 Nmux 210 172 17 158 9 172 17 158 11 Vinux 2100 172 17 158 11 re Ps emae etn Tee Figure 4 9 Add Managed Element to Site A Dialog Box 3 Select the Vmux 2100 row 172 17 158 11 to select it Click ea to add the selected ME to the site Click Set The Add Managed Element to Site A dialog box closes Close the Site A window Oo AD O U N Repeat this procedure for the remaining two devices adding one device to each site according to the following table Table 4 4 Typical Application S
106. nning Loopback Tests Note Access the Agent mode by selecting the bottom image of the device Access the Edit mode by selecting the top image of the device 7 1 Monitoring Object Status The Fault menu provides access to the system alarm options You can view alarm severity as well as mask alarms Different Fault menu options may appear depending on whether the user is working in Agent or Edit mode Viewing All Active Alarms The Display gt All command enables you to view active alarms at all levels system bundle or port gt To view all active alarms 1 In Agent mode only select the device Vmux 110 Ver 4 0 Monitoring Object Status 7 1 Chapter 7 Fault Management User s Manual 2 From the Fault menu select Alarms gt Display gt All or From the toolbar click B As the list of alarms is prepared a Progress Bar window illustrates the upload progress If no alarms exist the list will be empty 3 Sort the list of alarms by any one of the column values by clicking on the column header Each click toggles between ascending and descending order gag LA 1 172 17 158 49 Mux All Active Alarm List ee E S EAE ana e z e 8 DBS LEXICAL SANITY CORRECTION 18 NA DB UPDATE OCCURRED levent BF None A 87 LinkE1 T1 E1 SIGNAL LOSS major loff None 2 195 Bundle BUNDLE IS 005 major loff None 2 195 Bundle BUNDLE IS 005 major lon None 1 195 Bundle BUNDLE IS 005 major lo
107. of a status indication bar based upon its location and color Table 2 2 Vmux 110 Alarm Test Status Indication Bars Location Upper right of device port Upper right of device port Upper right of device port Upper right of device port Lower right of device port Lower right of device port Color Alarm Test Status Indication Transparent There are no alarms on the device port invisible Yellow Minor alarms exist on the device port Orange Major alarms exist on the device port Red Critical alarms exist on the device port Transparent All tests are stopped on the device port invisible Blue A test is active on one or more time slots of the device port Using the Graphical User Interface 2 7 Chapter 2 Installation and Operation User s Manual Selecting the Device or a Port By selecting an object you can manipulate or manage the selected system or port When selected a light blue frame is displayed around the selected window or object Only one object can be selected at a time There are two Vmux 110 user interface object levels e System whole device contains all of the parameters and functions that are common to the whole device e Port contains all of the parameters and functions of the selected port To select the entire device system e Inthe Element Manager window click any empty area of the device where there is no port To select a port Note e Inthe Element Manager wi
108. oice Port Status The Status command enables you to view the status of the FXS FXO or E amp M ports gt To display FXS FXO E amp M status 1 In Agent or Edit mode select the one of the Analog Voice ports 2 From the Configuration menu select Analog Voice gt Status The number of rows in the dialog box corresponds to the number of FXS FXO E amp M ports Vmux 110 Ver 4 0 Additional Tasks 3 37 Chapter 3 Configuration Management User s Manual 4 1 172 17 158 14 E amp M Status SRE Rea oP Bundle No ag Close Refresh Ready Figure 3 22 FXS Status Dialog Box Table 3 20 FXS EXO EEM Status Parameters Parameter Possible Values Remarks Port Port Name Connected Yes No Bundle No 1 8 State On Hook Off Hook Agent mode only Close Click lt Close gt to close the FXS FXO E amp M Status dialog box 3 38 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management Displaying Link E1 T1 Port Time Slot Assignments The TS Assignment command enables you to display time slot assignments for IP bundles Time Slot Assignments for Analog Voice ports are accessed through the System Level Configuration menu Time Slot Assignments for Link El and Link T1 ports are accessed through the Port Level Configuration menu For information on creating and managing bundle connections and time slots using the Service Cente
109. om the Statistics menu select Data Stream The Data Stream Dialog box appears see Figure 6 6 3 Click the desired yellow Data Stream cell to select it 4 Click lt Statistics gt The Data Stream Statistics Dialog Box appears see Figure 6 7 Viewing Data Stream Statistics for a Channel E1 T1 Port 6 9 Chapter 6 Performance Management User s Manual A 1 172 17 158 48 Data Stream ese Ri Port Channel E1 A ae ae eS lives Data Streams A Close Get successful CI Figure 6 6 Data Stream Dialog Box Statistics F Table 6 5 Data Stream Parameters Parameter Possible Values Remarks Port Channel E1 Channel T1 Data Streams Arranged in three groups Transparent SS7 1 SS7 2 HDLC 1 HDLC 4 Sub Channel 1 Sub Channel 8 Cells within each group are colored to indicate Selectable Yellow or Protected Blue Statistics Click lt Statistics gt to view the statistics for a selected cell Disabled if no selectable yellow cell is selected Reset Counters Click lt Reset Counters gt to reset the counters of selected port to 0 Disabled if no selectable yellow cell is selected Cancel Click lt Cancel gt to close the dialog box 6 10 Viewing Data Stream Statistics for a Channel E1 T1 Port Vmux 110 Ver 4 0 User s Manual Vmux 110 Ver 4 0 Chapter 6 Performance Management 4 1 172 17 158 48 Data Stream Statistics Legen
110. om the Statistics menu select LAN Statistics gt Rx Frame Types 6 12 Viewing Receive Frame Types Statistics for a LAN Port Vmux 110 Ver 4 0 User s Manual Chapter 6 Performance Management 4 1 172 17 158 48 Rx Frame Types Table and Graph Parameters x Delta Legend 6000 W Total Frames 4000 W Total Bytes 2000 EW Wi correct Frames 0 I Correct Bytes 10 40 30 10 41 30 10 42 30 10 43 30 Correct Broadcast Frames Time E Correct Multicast Frames For a different View click on the Legend Port ETH NET Running Time 3 days 04 01 40 Frames 404804 Bytes J Correct Frames 404804 Correct Bytes 29436913 ZE TERTESEER TEE z Correct Broadcast Frames 306572 2 d Correct Multicast Frames 18193 Rete EN A E Ee Reset Counters Close Poll et successful E 6 sec to next polling Figure 6 8 LAN Receive Frame Types Statistics Dialog Box Table 6 7 LAN Receive Frame Types Statistics Parameters Parameter Possible Values Remarks Port ETH NET ETH USER The system up time i e the time in hundredths of a second since the network management portion of the system was last re initialized Format DD days HH MM SS Running Time Status Bar Countdown Timer Displays number of seconds to next polling action Only in use when polling is enabled Rx Frame Type Note The following parameters vary depending on the device s hardware version The
111. om the toolbar click 1E 3 If there are errors to display the Sanity Check Errors dialog box appears As the list of alarms is prepared a Progress Bar window illustrates the upload progress Monitoring Object Status Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management 4 If there are no errors to display a message box appears with the appropriate message No Sanity Errors or No Valid Errors E 1 172 17 158 41 4E amp M Sanity Check Error List Se x Bundle Description MAIN LINK ROUTER S INTERFACE HAS NO IP ADDRESS MAIN LINK ROUTER S INTERFACE HAS ILLEGAL MASK Print Save to File Close Ready Figure 7 9 Sanity Check Errors Dialog Box Table 7 7 Sanity Checks Errors Parameters Parameter Possible Values Remarks E W E Error number W Warning number Port Port where the error occurred TS Timeslot where the error occurred Bundle IP Bundle where the error occurred Description Description of the error Print Click lt Print gt to print the Sanity Check Errors dialog box Save to File Click lt Save to File gt to save the Sanity Check Errors List The Save dialog box appears In the File Name field enter the name of the file In the File of type field select Acrobat pdf or HTML htm Click Save Close Click lt Close gt to close the Sanity Check Errors dialog box Vmux 110 Ver 4 0 Monitoring Object Status 7 15 Chapter 7 Faul
112. onal Parameters Vmux 110 Ver 4 0 User s Manual Parameter VLAN ID Chapter 3 Configuration Management Table 3 8 VLAN Table Parameters Possible Values Remarks 1 4094 Default 1 ETH Net Transparent This port transmits egress packets for this port as unmodified Forbidden This port is prohibited from being included in the egress list for this VLAN Untagged This port transmits egress packets for this VLAN as untagged Tagged This port transmits egress packets for this port as tagged Default Forbidden ETH User Transparent This port transmits egress packets for this port as unmodified Forbidden This port is prohibited from being included in the egress list for this VLAN Untagged This port transmits egress packets for this VLAN as untagged Tagged This port transmits egress packets for this port as tagged Default Forbidden Link Mng OR Channel Mng available if Connect Through is Link E1 T1 or Serial Port Transparent This port transmits egress packets for this port as unmodified Forbidden This port is prohibited from being included in the egress list for this VLAN Untagged This port transmits egress packets for this VLAN as untagged Tagged This port transmits egress packets for this port as tagged Default Forbidden Add Click lt Add gt to add an entry to the VLAN table Change Click lt Change gt to change the parameter values of an entry in the VLAN tab
113. onfiguration Agent Update Configuring Signaling Profile Parameters Chapter 2 Both Configuration Channel E1 T1 devices only 2 10 Using the Graphical User Interface Signaling Profile Vmux 110 Ver 4 0 User s Manual Chapter 2 Installation and Operation Table 2 5 System Management Options Configuration Menu Cont Task Location in User s Mode Path in RADview Manual Viewing Bundle Connection Table Parameters Chapter 3 Both Configuration Bundles Connection Table Configuring Bridge Ports Chapter 3 Both Configuration Bridge Ports Configuring the VLAN Table Chapter 3 Both Configuration VLAN Table Displaying Analog Voice Port Chapter 3 Both Configuration Time Slot Assignments Analog Voice TS Assignment Displaying Analog Voice Port Status Chapter 3 Both Configuration w Analog Voice w Status Configuring FXS Timeouts and Cadences Chapter 3 Both Configuration w Analog Voice Timeouts amp Cadences Polling the Agent Chapter 3 Both Configuration System Commands Poll Agent Resetting the Hardware Chapter 3 Agent Configuration System Commands Reset HW Resetting the Configuration Chapter 3 Agent Configuration Vmux 110 Ver 4 0 System Commands Reset Configuration Using the Graphical User Interface 2 11 Chapter 2 Installation and Operation System Level Fault Menu User s Manual In Edit mode the Fault menu is disabled gray if there is no communication with the Agent Table 2 6 System Management Options
114. or each interval in the table Int No Total 1 N number of the selected interval or group of intervals to examine From hh mm Start time of data to be examined When working with all intervals Total the value of N 15min To hh mm End time of data to be examined When working with all intervals Total the value of CurrentTime ElapsedTime ESs Errored Seconds Number of seconds in this interval in which an event or alarm occurred SESs Severe Errored Seconds Number of seconds in the current interval in which at least 320 CRC events or one OOF event occurred UASs Unavailable Seconds Number of seconds in the current interval in which a failed signal state exists A failed signal state occurs after 10 consecutive severe errored seconds This state is cleared only after the Vmux processes 10 consecutive seconds of data without an SES CSSs Controlled Slip Seconds Number of seconds in the current interval in which at least one controlled SLIP event occurred BESs Bursty Errored Seconds Number of seconds in the current interval in which 2 319 CRC events occurred Close Click lt Close gt to close the Intervals Statistics Vmux 110 Ver 4 0 6 6 Viewing Data Stream Statistics for a Channel E1 T1 Port The Data Stream command enables you to view T1 or E1 port level data stream statistics as a table To view data stream statistics for a Channel E1 T1 Port 1 In Agent mode only select an E1 T1 port 2 Fr
115. our signal level closer to the expected repeater signal level on the cable 0 7 5 15 0 22 5 Default O Disabled when Interface Type Is set to DSU Idle Code hex Vmux 110 Ver 4 0 Hexadecimal code transmitted to fill idle unused time slots in frames transmitted through the selected port 00 FF Default FF Note The following values are not allowed OH 8H 10H 12H 21H 24H 42H 49H 84H 92H Setting the Operational Parameters 3 31 Chapter 3 Configuration Management User s Manual Parameter Signaling Mode TS Rate Kbps Table 3 15 Channel T1 SW Cfg Tab Parameters Cont Possible Values Remarks The signaling mode of the Framer module CCS Common Channel Signaling The signaling is not within the channel s time slot Instead a separate time slot is reserved and used for signaling Robbed Bit Robbed Bit is a signaling method used for T1 links dedicating 7 bits for voice and 1 bit for signaling Default CCS 56 64 Default 64 SS7 FISU Suppression SS7 Suppresion is used for SS7 Spoofing The SS7 spoofing terminates the keep alive messages from the local VMUX without sending them over the network thus improving the bandwidth utilization FISU means Fill in Service Unit The keep alive that is sent when no one Is talking on the line This object enables the configuration of thepercentage of SS7 Keep Alive packets that will be discarded 0 No Suppression 10 90 in
116. play All alarms System level alarms only Port level alarms only may be limited to a specific port IP Bundle alarms only may be limited to a specific bundle The list of alarms displayed by default includes all active alarms for the selected group plus any inactive alarms in that group with at least one attribute set to Yes 4 Sort the list of alarms by any one of the column values by clicking on the column header Each click toggles between ascending and descending order 7 10 Monitoring Object Status Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management ig l4 1 172 17 158 49 Alarm Attributes REMOVE Figure 7 6 Alarm Attributes Dialog Box Vmux 110 Ver 4 0 Monitoring Object Status 7 11 Chapter 7 Fault Management User s Manual Table 7 5 Alarm Attributes Parameters Parameter Possible Values Remarks Level All System port and IP Bundle level alarms System Only System level alarms only Port Port level alarms only Bundles IP Bundle level alarms only Port All Link E1 Link T1 Serial Link Specific Port to display in the Alarm Attributes List Enabled only when Level is set to Port Bundle All 1 31 E1 1 24 T1 Specific Bundle to display in the Alarm Attributes List Enabled only when Level is set to Bundle Attributes All All alarms are displayed according to the level selection Mask Only entries that are masked Yes are displayed
117. r refer to Chapter 7 of the RADView SC Vmux System Manual Note f A e Perform a Read before opening the TS Assignment dialog box to ensure that the most up to date information Is displayed The Read command is described in Reading Uploading the Agent Configuration page 3 55 e For Link El T1 ports when Line Type is set to Unframed Time Slot Assignment s not relevant and the menu is unavailable Unframed E1 T1 Ports are treated like a pipe of 2 Mbps e You should assign which Time Slots to use according to the bandwidth allocated from the carrier For example if the available bandwidth is 128 kbps then you should select two Time Slots of 64 kbps each The carrier may also require certain Time Slot numbers Vmux 110 uses all of the Time Slots that you define gt To display configure time slot assignments for a Link E1 T1 Port 3 In either Agent or Edit mode select the Link E1 or Link T1 port 1 From the Configuration menu select TS Assignment The TS Assignment dialog box appears displaying IP Bundle Connections Each Bundle Connection contains the Time Slots numbers of the bundle and their Destination Time Slots numbers x 4 1 172 17 158 14 TS Assignment xj Link T4 4 2 7 H 12 16 eis Sinica i i Refresh Get successful Figure 3 23 TS Assignment Dialog Box Link E1 T1 Port Vmux 110 Ver 4 0 Additional Tasks 3 39 Chapter 3 Configuration Management User
118. r 2 Switching Note When Router is enabled and Connect Through is ETH then Net User Routing Mode is Layer 3 Routing Default Gateway enabled only if Router is enabled Enable is The IP address of the next hop 0 0 0 0 255 255 255 255 Default 0 0 0 0 Router Default Gateway is disabled checked Set Click lt Set gt to save System Parameters settings Cancel Click lt Cancel gt to cancel the selections made in the dialog box and close the box Selecting the Date Format The Date Format command enables you to select the format in which you want the system date to appear in all dialog boxes gt To set the date format 1 In Agent mode only select the device 2 From the Configuration menu select Date Format 3 Select a date format from the dropdown menu Possible formats are DD MM YYYY MM DD YYYY YYYY MM DD Setting the Date and Time The Date amp Time command enables you to adjust the system clock gt To set the system date and time 1 In Agent mode only select the device 2 From the Configuration menu select Date amp Time Setting the System Parameters Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management 3 Configure the desired parameters and click lt Set gt A 1 172 17 158 14 Date amp Time SetUp eo x Format DD MM Y YYY Date s 07 2006 Time 17 19 18 Set Cancel Get successful C Figure 3 4 Date amp Time
119. rity and VLAN tag handling of the Vmux 110 bridge Separate tabs control the configuration for the ETH NET port ETH USER port and the Link Channel Mng Internal CPU interface For example you can use this dialog to configure a port to automatically add a single VLAN to received packets or to double tag double stack the packets before forwarding them to the destination Setting the Operational Parameters 3 11 Chapter 3 Configuration Management User s Manual Note Bridging connects bridges network segments together to provide Layer 2 data link level switching e The Link Channe Ming Management interface refers to a virtual port which is also known as the CPU port or the Internal port in the CLI The CPU port processes the packets received from the user port and the network port gt To configure bridge ports 1 In Agent mode for viewing or Edit mode for setting select the device 2 From the Configuration menu select Bridge Porrts The Bridge Ports Configuration Dialog Box appears 3 Click the tab that corresponds to the port that you want to configure the ETH NET tab ETH USER tab or Link Channel Mng tab 4 Configure the desired parameters and then click lt Set gt 5 If a confirmation dialog box appears click lt OK gt a 1 172 17 158 14 Bridge Ports Com TETANET ETH USER Link Ming Ingress Filtering Disable Port VID 1 Default Priority Tag
120. rt e Viewing Intervals Statistics for an E1 T1 Port e Viewing Data Stream Statistics for an E1 T1 Port e Viewing Receive Frame Types Statistics for a LAN Port e Viewing Transmit Frame Types Statistics for a LAN Port e Viewing Errors Statistics for a LAN Port e Viewing Frame Sizes Statistics for a LAN Port e Viewing Statistics for an E1 T1 or Serial Port Link 6 1 Introduction Vmux 110 continuously collects performance statistics for its various ports and for bundle connections The collected data enables network administrators to monitor the transmission performance and thus the quality of service provided to users RADview can display Current Statistics information and graphs displaying an immediate view of the statistics counters The Statistics window is refreshed periodically according to the Polling Interval or manually whenever you click the lt Poll gt button RADview can also display Intervals Statistics information and graphs that aggregate the statistics over 15 minute intervals Note All performance management is performed in Agent mode Access Agent mode by selecting the bottom image of the device Vmux 110 Ver 4 0 Introduction 6 1 Chapter 6 Performance Management User s Manual gt Parameter Polling Interval sec 6 2 Setting the Polling Interval Use the Statistics gt Polling Interval command to enable polling and set the interval between polling attempts Statistics windows other than Inter
121. rt Time Slot Assignments 0 eeeeeeeeeeeeeeeeeeeeeeeeeeeeees 3 39 Displaying Voice Port Time Slot Assignment ceeeeeeeeeeeeeeeaeeeeeeeaeeeeeeeeaaeeeeeeaa 3 40 TS Assignment Dialog Box Analog Voice POFt cece eee e eee e tere eter eee teeeeteeeteeeeeereeees 3 41 TS Assignment Dialog Box Voice Channel E1 T1 Port ccccceeeeeeeeeeeeeeeeeeeteeeetneeeeees 3 42 Displaying Bundle Connection Parameters cccceeeceeeeeeeeeeeeeeeeeaeeeeeeeaaeeeeeeaaaeeeeeeea 3 43 Bundle Connection Details eeeecececeeeeeeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeseeeeteeeeteeeneegs 3 44 Reading Uploading the Agent Configuration ssssssssersrrrrrrrrnrrnrnrrnnrrnnrnnrnn e 3 58 Updating Downloading the Configuration to the Agent eeeeeeeeeeeeeeees 3 59 Resetting Vmux 110 to the Default Configuration cccceeeeeeeeeeeeeeeeeeeeeaeeeeeeaee 3 60 Polling the Agent iiion ace dives Gnd Gitlin vivre Riedie 3 61 Resetting Vm X 10 s cscace siveascveassezecaaedscagasidaee seas can ediseg ences bbaitbencs sueeacsyviasedaesedeeeaces 2 61 Chapter 4 Configuring a Typical Application APDUGQTON cece sttaasticsccueepeteadaeee see aeea aA Aa tack aana Koat aeaaea ien 4 1 Configuration SEQUENCE 200 eee ce eee e cette eee e ee ee eee e aiaiai inanki iii a aaa ia ekaia EES 4 2 4 1 Configuring the Vmux Units for Management cceeceeeeneeeee eee eeeee tena eeeeeaaaeeeeeaaaeeeee
122. s OK Click lt OK gt to automatically download the Edit configuration Cancel Click lt Cancel gt to close the Update Configuration dialog box without downloading the Edit configuration Abort Click lt Abort gt to stop updating the current Agent configuration Note If the configuration download Is interrupted for any reason a message box appears with the message Update was interrupted Click lt Cancel to cancel the update operation Click Retry to attempt to resend the rest of the unsent data starting with the last sent message Resetting Vmux 110 to the Default Configuration The Reset Configuration command enables you to reset the Agent s configuration back to the factory defaults Use this command when you wish to reconfigure all of the parameters from a clean starting point This is useful when Vmux 110 s current configuration is completely unsatisfactory such as when moving a device to another site or if the configuration database has become corrupted or the device s software has been upgraded 3 60 Additional Tasks Vmux 110 Ver 4 0 User s Manual Chapter 3 Configuration Management gt To reset the configuration 1 In Agent mode only select the device 2 From the Configuration menu select System Commands gt Reset Configuration 3 Click lt OK gt The hardware configuration is reset 4 1 172 17 158 14 Reset me axl RESETTING AGENT CONFIGURATION Current configuration will be
123. s no communication with the Agent and the Agent window is not currently displayed Table 2 8 System Management Options Window Menu Task Location in Mode Path in RADview User s Manual Toggling the Agent View Chapter 2 Both Window Agent View System Level Options Menu Table 2 9 System Management Options Options Menu Task Location in Mode Path in RADview User s Manual Configuring the Manager List Chapter 3 Agent Options Manager List Setting Management Access Authorizations Chapter 5 Agent Options we Access Vmux 110 Ver 4 0 Using the Graphical User Interface 2 13 Chapter 2 Installation and Operation User s Manual Port Level Operations Table 2 10 lists the configuration management tasks that are available when you select a port in Agent or Edit Mode Port Level Configuration Menu Table 7 10 Port Management Options Configuration Menu Task Location in Mode Path in RADview User s Manual Configuring Port Information Chapter 3 Both Configuration Port Info Displaying Link E1 or Link T1 Port Chapter 3 Both Configuration Time Slot Assignments TS Assignment Copying a Port Configuration Chapter 3 Edit Configuration gt Copy Configuring Port User Information Chapter 3 Edit Configuration User Info Port Level Diagnostics Menu Table 2 11 Port Management Options Diagnostics Menu Tasks Location in Mode Path in RADview User s Manual Running a Loopback Test on a Port Chapter 5 Agent Diagnostics wTest Port Level F
124. se the dialog box Poll Click lt Poll gt to update the information displayed in the dialog box 6 9 Viewing Errors Statistics for a LAN Port Use the LAN Statistics Errors command to display error statistics for a LAN port To view receive errors statistics for a LAN Port Vmux 110 Ver 4 0 1 In Agent mode select a LAN port 2 From the Statistics menu select LAN Statistics gt Errors Viewing Errors Statistics for a LAN Port 6 15 Chapter 6 Performance Management 4 1 172 17 158 48 Errors Table and Graph Parameters User s Manual tegen Wi jabber MECRC Error Frames I Fragments o W discarded Frames 9 15 00 9 16 00 9 17 00 9 18 00 Filtered Frames Time W Total Collisions For a different view click on the Legend Port ETH NET ae ras i A Running Time 0 days 20 11 33 Jabber HE E R ERE ees 0 CRC Error Frames 0 o Fragments Discarded Frames 0 0 Filtered Frames 0 o Total Collisions Reset Counters Close Poll et successful 9 sec to next polling Parameter Jabber Figure 6 10 LAN Errors Statistics Dialog Box Table 6 9 LAN Errors Statistics Parameters Possible Values Remarks Total number of packets received that were longer than 1518 octets excluding framing bits but including FCS octets and had either a bad Frame Check Sequence FCS with an integral number of octets FCS Error or a bad FCS with
125. ssary to first configure some basic Vmux 110 parameters via an ASCII terminal The following steps are required 1 Connecting a Terminal to the Control Port 2 Disabling the Router 3 Configuring the host IP parameters IP address IP mask default gateway SNMP Communities 4 Defining the Network Management Station in the Manager List For more detailed information about configuring Vmux 110 for Network Management see Chapter 4 of the Vmux 110 Installation and Operation Manual Connecting a Terminal to the Control Port gt Vmux 110 Ver 4 0 In order to configure the basic IP parameters it is necessary to connect an ASCII terminal to the Vmux 110 control port and log in To configure the Vmux 110 system parameters 1 Configure an ASCII terminal to One start bit Eight data bits No parity One stop bit No flow control VT100 emulation Pre configuring Vmux 110 for Network Management 2 1 Chapter 2 Installation and Operation User s Manual Connect the terminal to the Vmux 110 CONTROL port Press lt Enter gt several times to allow Vmux 110 to detect the rate Initiate the control session by entering the administrator user name and password Disabling the Router The Vmux 110 host IP parameters may be assigned automatically via DHCP or they may be configured manually In order to manually configure the Host IP Parameters the Vmux 110 router must be disabled gt To disable the Vmux 110 router
126. t Management User s Manual Displaying the All Buffer Alarms List The History Log gt All command enables you to display all contents of the alarm buffer that contains all recorded alarms for the device gt To display the alarm buffer for all alarms 1 In Agent mode select the device 2 From the Fault menu select History Log gt All 3 Sort the list of alarms by any one of the column values by clicking on the column header Each click toggles between ascending and descending order 4 1 172 17 158 14 All Buffer Alarms Re e A 09 07 2006 09 28 33 MAIN LINK OVERFLOW 09 07 2006 09 29 43 MAIN LINK OVERFLOW 09 07 2006 09 31 13 MAIN LINK OVERFLOW 09 07 2006 09 32 23 MAIN LINK OVERFLOW 09 07 2006 09 33 53 MAIN LINK OVERFLOW 09 07 2006 09 35 03 MAIN LINK OVERFLOW 09 07 2006 09 37 33 MAIN LINK OVERFLOW 09 07 2006 09 37 43 MAIN LINK OVERFLOW 09 07 2006 09 39 13 MAIN LINK OVERFLOW 09 07 2006 09 39 51 MAIN LINK OVERFLOW 09 07 2006 09 41 21 MAIN LINK OVERFLOW 09 07 2006 09 42 31 j VERI p 09 07 2006 09 44 01 MAIN LINK OVERFLOW 09 07 2006 09 45 11 MAIN LINK OVERFLOW 09 07 2006 09 46 41 MAIN LINK OVERFLOW 09 07 2006 09 47 51 MAIN LINK OVERFLOW 09 07 2006 09 49 21 MAIN LINK OVERFLOW 09 07 2006 09 49 52 MAIN LINK OVERFLOW 09 07 2006 09 51 22 Figure 7 10 All Buffer Alarms Dialog Box Table 7 8 All Buffer Alarms Parameters
127. t TS Figure 3 24 TS Assignment Dialog Box Analog Voice Port Table 3 23 TS Assignment Parameters Analog Voice Port Possible Values Remarks The analog voice port number The Bundle No to which this timeslot belongs Cells are color coded to indicate usage or availability Dark Blue In Use Gray Available Time Slot Type V voice Note Analog Voice ports are always type V Destination TS Close Vmux 110 Ver 4 0 Click lt Close gt to close the dialog box Additional Tasks 3 41 Chapter 3 Configuration Management User s Manual TS Assignment Dialog Box Voice Channel E1 T1 Port 4 1 172 17 158 47 TS Assignment A i x Source TS TS 4 aa ar a s le E A EE Te As 12 143 14 15 16 17 18 19 20 21 22 23 24 Bundle Type Destination TS Port Te eet successful j Figure 3 25 TS Assignment Dialog Box Voice Channel E1 T1 Port Table 3 24 TS Assignment Parameters Voice Channel E1 T1 Port Parameter Possible Values Remarks Source TS TS The voice port number Bundle The Bundle No to which this timeslot belongs Cells are color coded to indicate usage or availability Dark Blue In Use Gray Available Type Time Slot Type Destination TS H1 H2 H3 H4 HDLC 1 2 3 or 4 S1 S2 SS7 Signaling number 1
128. ter 5 Security Management 5 1 Setting Management Access Authorizations ccceecceceeeeeeeeeeeeeeeeeeeeeeeaeeeeeeeaaaeeeeeaaaaees 5 1 5 2 UNIX Users and PermiSSIONS 2 sccecscetiescoudt idgaesccdee tense vias latch eedshsnbsadiveacsubiaciedstvedsbcbaans 5 2 Chapter 6 Performance Management OL IMMFOGUCTH ON nsss a a a a aa aae ENAR aai 6 1 6 2 Setting the Polling Interval sssesesssesissssstrissririrestirrrtttriretttirettrrrettnrrtstttnraartrnensrennt 6 2 6 3 Viewing Bundle Connection Statistics s ssesssssesssrestrisetttirettriretttrrtstrrrrssrrrrersrnnnt 6 2 6 4 Viewing Current Statistics for an EL T1 Port cccceseessceceecceeeceeeeeeeeeeeceeeeeeeeeeeeeeeeeess 6 6 6 5 Viewing Intervals Statistics for an E1 T1 POrt ccccccccccccscceseseesececeeeeeseeseseeeeeeeeeeeeeeaas 6 8 6 6 Viewing Data Stream Statistics for a Channel E1 T1 Port ccceccceeceeceeeeeeeeeeeeeeees 6 9 6 7 Viewing Receive Frame Types Statistics for a LAN POrt ccceeeeseeeeeeeeeeeeeeeeaeeeeeeeaaees 6 12 6 8 Viewing Transmit Frame Types Statistics for a LAN Port cccceeeeeeeeeeeeeeeeeeeeeeeaaees 6 14 Vmux 110 Ver 4 0 User s Manual Table of Contents 6 9 Viewing Errors Statistics for a LAN Port ccccceeeeeeeeeeeeee eee eeeeeeaeeeeeeeaeeeeeesaaeeeeeesaaees 6 15 6 10 Viewing Frame Sizes Statistics for a LAN Port cccceeeeeeeeeeeeeeeeeeeeeeeaeeeeeeesaaeeeeeeaaaes 6 17 6 11 Viewing Statistics for
129. ter the name of the file In the File of type field select Acrobat pdf or HTML htm Click Save This button is disabled if the table is empty Clear Click lt Clear gt to clear the Mux Active Alarm list This button is disabled if the table is empty Close Click lt Close gt to close the Mux Active Alarm List dialog box Refresh Click lt Refresh gt to update the Mux Active Alarm List Viewing IP Bundles Active Alarms Vmux 110 Ver 4 0 The Display gt IP Bundles command enables you to view IP Bundle alarms gt To view all IP Bundles Active Alarms 1 In Agent mode select the device 2 From the Fault menu select Alarms gt Display gt IP Bundles The IP Bundle Active Alarms dialog box appears see P Bundle Active Alarms page 7 6 3 To view a list of all alarms for all bundles click lt All Bundles The All Bundles Active Alarm List dialog box appears see A Bundles Active Alarm List page 7 7 4 To view alist of alarms for a single bundle select a table entry and click lt One Bundle gt The Bundle Active Alarm List dialog box appears see Bundle Active Alarm List page 7 9 As the list of alarms is prepared a Progress Bar window illustrates the upload progress If no alarms exist the list will be empty Monitoring Object Status 7 5 Chapter 7 Fault Management User s Manual IP Bundle Active Alarms ee Bundle 3 gag 4 1 172 17 158 49 IP Bundle Active Alarms
130. tions Agent mode 2 14 Port management options Agent mode 2 14 Port statistics displaying current data 6 6 Port user information configuring 3 3 Ports configuring 3 19 Profiles signaling 3 9 R RADview launching 2 4 RADview using 2 5 RADview SC Vmux 110 overview 1 2 Read Configuration dialog Edit mode 3 59 Receive statistics Ethernet port 6 12 LAN port 6 12 Reset hardware dialog Agent mode 3 62 Resetting configuration 3 60 hardware 3 61 Vmux 110 Ver 4 0 User s Manual S Security UNIX users and permissions 5 2 Selecting Objects 2 8 Serial port link statistics 6 19 Signaling Profile detail 3 9 viewing 3 9 Signaling Profile Parameters configuring 3 9 Statistics viewing current statistics for an E1 1 Port 6 6 IP bundle connection statistics 6 2 Statistics viewing El port data stream 6 9 El port intervals Statistics 6 8 E1 T1 port link statistics 6 19 Ethernet port receive statistics 6 12 Ethernet port transmit statistics 6 14 LAN port error statistics 6 15 LAN port frame sizes statistics 6 17 LAN port receive statistics 6 12 LAN port transmit statistics 6 14 Serial port link statistics 6 19 T1 port data stream 6 9 T1 port intervals Statistics 6 8 Status indicators 2 8 Status Indication Bars alarm test 2 7 Status of an analog voice port viewing 3 37 System Information configuring 3 2 dialog Agent mode 3 2 System level operations Agent mode
131. tm Click Save disabled if the list if empty Close Click lt Close gt to close the New Buffer Alarms list Refresh Click lt Refresh gt to update the New Buffer Alarms list Vmux 110 Ver 4 0 Monitoring Object Status 7 17 Chapter 7 Fault Management User s Manual Displaying the Port Active Alarm List The Alarms gt Display command enables you to view active alarms for a selected port gt To display the active alarms for a port 1 In Agent mode select a port 2 From the Fault menu select Alarms gt Display 3 Sort the list of alarms by any one of the column values by clicking on the column header Each click toggles between ascending and descending order 4 1 172 17 158 14 Port Active Alarm List Port Serial Link own ion ae mek ome SS TC a a 7 Print Save to File Clear Close Refresh Ready j Figure 7 12 Port Active Alarm List Dialog Box 7 18 Monitoring Object Status Vmux 110 Ver 4 0 User s Manual Chapter 7 Fault Management Table 7 10 Port Active Alarm List Parameters Parameter Possible Values Remarks Port The port reporting the alarm Code Alarm code Description Description of the alarm Severity Event Minor Major Warning Critical Status Off On Mask Mask None Counter Number of times this alarm occurred since the system was last started or this alarm was last cleared Print
132. to 12 characters Contact The name of the person responsible for the functioning of this device a string of up to 32 characters Location The exact location of this device a string of up to 32 characters System Up Time Agent mode only The amount of time that elapsed since this device was initialized or reset Format XX Days HH MM SS Number of Interfaces Agent mode only The number of physical and logical interfaces on this device Set Agent mode only Click lt Set gt to save System Information settings Cancel Agent mode only Click lt Cancel gt to cancel the selections made in the dialog box and close the box Refresh Agent mode only Click lt Refresh gt to update the System Information Close Edit mode only Click lt Close gt to close the System Information dialog box Setting Port User Information The User Info command enables you to assign user information for a port This information is useful for keeping track of contact information specific to each port gt To change port user information parameters I 2 3 4 Vmux 110 Ver 4 0 In Edit mode select a port From the Configuration menu select User Info Configure User Name and User Info Click lt Set gt Setting the System Parameters 3 3 Chapter 3 Configuration Management User s Manual E 1 172 17 158 14 Port Port Serial Link User Name User Info Set
133. ts constructed from the following list O hex 0000 0 1 hex 0001 1 2 hex 0010 A bit 3 hex 0011 B bit 4 hex 0100 C bit 5 hex 0101 D bit 6 hex 0110 Inverse A 7 hex 0111 Inverse B 8 hex 1000 Inverse C 9 hex 1001 Inverse D Viewing Signaling Profile Parameters gt To view signaling profile parameters Vmux 110 Ver 4 0 1 In either Agent or Edit mode select the device 2 From the Configuration menu select Signaling Profile Setting the Operational Parameters 3 9 Chapter 3 Configuration Management User s Manual 4 1 172 17 158 48 Signaling Profile Parameter Profile Number Figure 3 6 Signaling Profile Dialog Box Table 3 6 Signaling Profile Parameters Possible Values Remarks The identification number assigned to each signaling profile 12 5 A A B C D Inverse A Inverse B Inverse C Inverse D 1 0 Default A B A B C D Inverse A Inverse B Inverse C Inverse D 1 0 Default B C A B C D Inverse A Inverse B Inverse C Inverse D 1 0 Default C D A B C D Inverse A Inverse B Inverse C Inverse D 1 0 Default D Busy Tone value for busy signal 0000 1111 Default 1000 Applicable only for Rx translation Idle Tone value for idle signal 0000 1111 Default 1000 Applicable only for Rx translation Change Click lt Change gt to change the value of a selected entry In
134. ual Table 3 9 FXS Timeouts and Cadences Parameter Parameter Possible Values Remarks Timeouts Ringing Sec 60 600 Default 120 Flash mSec 10 2000 Default 700 Ringing Cadence 1 On Period 1 Sec 0 1 5 0 Default 1 0 Off Period 1 Sec 0 1 5 0 Default 3 0 Period 2 Enabled Checked Unchecked When checked Period 2 is enabled On Period 2 Sec 0 1 5 0 Default 1 0 Note This parameter is enabled when Period 2 Is enabled Off Period 2 Sec 0 1 5 0 Default 3 0 Note This parameter is enabled when Period 2 Is enabled Ringing Cadence 2 On Period 1 Sec 0 1 5 0 Default 1 0 Off Period 1 Sec 0 1 5 0 Default 3 0 Period 2 Enabled Checked Unchecked When checked Period 2 is enabled On Period 2 Sec 0 1 5 0 Default 1 0 Note This parameter is enabled when Period 2 Is enabled Off Period 2 Sec 0 1 5 0 Default 3 0 Note This parameter is enabled when Period 2 Is enabled Refresh Click lt Refresh gt to refresh the data displayed in the dialog box Close Click lt Close gt to close the FXS Timeouts and Cadences dialog box Set Click lt Set gt to update the FXS Timeouts and Cadences information with the new Edit mode values Cancel Click lt Cancel gt to cancel the selections made in the dialog box and close the box Edit mode 3 18 Setting the Operational Parameters Vmux 110 Ver 4 0 User
135. undle Connection Statistics e Viewing Current Statistics for an E1 T1 Port e Viewing Intervals Statistics for an E1 T1 Port e Viewing Data Stream Statistics for an Channel E1 T1 Port e Viewing Receive Frame Type Statistics for a LAN Port e Viewing Transmit Frame Type Statistics for a LAN Port e Viewing Error Statistics for a LAN Port e Viewing Frame Size Statistics for a LAN Port e Viewing Statistics for an E1 T1 or Serial Port Link Fault Chapter 7 e Viewing All Active Alarms e Viewing System Level Active Alarms e Viewing IP Bundles Active Alarms e Clearing the System Level Active Alarm Buffer e Clearing All Levels of the Active Alarm Buffer e Configuring Alarm Attributes e Configuring Alarm Reports e Displaying Sanity Check Errors e Displaying the All Buffer Alarms List e Displaying the New Buffer Alarms List e Displaying the Port Active Alarm List e Clearing the Port Active Alarm Buffer e Running Loopback Tests 1 4 RADview SC Vmux 110 Overview Vmux 110 Ver 4 0 Chapter 2 Installation and Operation This chapter describes how to configure Vmux 110 for management and explains how to perform the following tasks e Pre configuring Vmux 110 for Network Management e Connecting Vmux 110 to the Management Station e Launching RADview Vmux 110 e Using the Graphical User Interface 2 1 Pre configuring Vmux 110 for Network Management To remotely administer Vmux 110 via a Network Management Station NMS it is nece
136. urrent command to display E1 T1 port statistics for the current 15 minute interval The Time Elapsed field shows how much time passed since the beginning of the current interval Statistics are displayed in either table or graph format gt To view the current statistics for an E1 T1 Port 1 In Agent mode only select an E1 or T1 port 2 From the Statistics menu select Current 3 The Current Statistics dialog box shows the amount of time that error s exist s in the current measurement interval Each interval is 15 minutes 900 seconds gag LA 1 172 17 158 49 Current Statistics Port Link E1 Iae y y y 0 5 10 15 20 25 30 Time Elapsed sec For a different View click on the Legend Time Elapsed sec 0 ESs 10 SESS 0 UASs 16317 CSSs 0 BESs 1 Close Poll et successful E 4sec to next polling Figure 6 4 Current Statistics 6 6 Viewing Current Statistics for an E1 T1 Port Vmux 110 Ver 4 0 User s Manual Chapter 6 Performance Management Table 6 3 Current Statistics Parameters Parameter Possible Values Remarks Port Link E1 Link T1 Channel E1 Channel T1 Status Bar Countdown Timer Displays number of seconds to next polling action Only in use when polling is enabled Timer Displays system time as of the last polling refresh action Current Data Time Elapsed Number of
137. val Statistics are refreshed periodically according to the Polling Interval or manually whenever you click the lt Poll gt button To configure the polling interval 1 In Agent mode select a port From the Statistics menu select Polling Interval 2 3 In the Polling Interval field select the desired value 4 Check Polling Enable to enable polling for E1 or T1 ports only 5 Click lt Set gt Polling Interval sec 10 Figure 6 1 Polling Interval Dialog Box Table 6 1 Polling Interval Parameters Possible Values Remarks Time between polling attempts 5 60 in steps of 5 Default 10 Set Click lt Set gt to save polling interval settings Cancel Click lt Cancel gt to close the Polling Interval dialog box without saving changes 6 3 Viewing Bundle Connection Statistics The Bundle Connection Table command enables you to view statistics for all IP bundle connections To view IP Bundle statistics 1 In Agent mode select the device 6 2 Viewing Bundle Connection Statistics Vmux 110 Ver 4 0 User s Manual Chapter 6 Performance Management 2 From the Statistics menu select Bundle Connection Table The Bundle Connection Table Appears For more detailed configuration information about a specific bundle entry in the Bundle Connection Table select a bundle and click lt View gt The parameters for the Bundle Connection Table dialog box Figure 6 2 and for the detailed
138. y monitors network performance QoS CoS and resource allocation e Security management controls and restricts access to network resources 1 2 RADview SC Vmux 110 Overview Vmux 110 Ver 4 0 User s Manual Chapter 1 Introduction Overview of the Vmux 110 Management Functions Table 1 1 lists the operations that you can perform via RADview and their locations in this manual Table 1 1 Management Functions Operation Location in User s Manual Configuration Chapter 3 e System Information e Port User Information e System Parameters e Date and Time e Manager List e Signaling Profile Parameters e Bridge Ports e VLAN Table e FXS Timeouts and Cadences e Port Information e Copying a Port Configuration e Displaying Host IP Information e Displaying Analog Voice Port Status e Displaying Link E1 or Link T1 Port Time Slot Assignments e Displaying Analog Voice Port Time Slot Assignments e Displaying Bundle Connection Parameters e Reading Uploading the Agent Configuration e Updating Downloading the Configuration to the Agent e Resetting Vmux 110 to the Default Configuration e Polling the Agent e Resetting Vmux 110 Security Chapter 5 e Setting Management Access Authorizations Vmux 110 Ver 4 0 RADview SC Vmux 110 Overview 1 3 Chapter 1 Introduction User s Manual Table 1 1 Management Functions Cont Operation Location in User s Manual Peformance Chapter 6 e Setting the Polling Interval e Viewing B

Download Pdf Manuals

Related Search

RADview SC/Vmux 110

RADview-SC/Vmux-110

Contents

Download Pdf Manuals

Related Search

Related Contents