T9101 & Cancel Panel
Contents
1. Repaging Repaging sends repeated messages to the pagers Server To set the re page time for Server pagers e Press PROG PROG 6 e Press 1 for Re page At time use the number keys to enter as mm ss minute seconds then press ENT The screen will briefly show the updated re page time If done press 6 for Yes if not press 10 for No Long Range Systems 12 T9101 amp Cancel Panel User Manual Manager To setthe Manager to be paged once after the third re page e Press PROG PROG 6 e Press 10 for More At mgr press 6 for Manager e Press 5 to turn On If done press 6 for Yes if not press 10 for No To turn Off the Manager to be paged e Press PROG PROG 6 e Press 10 for More At mgr press 6 for Manager e Press 10 to turn Off If done press 6 for Yes if not press 10 for No Repeater Delay When using a repeater it may be necessary to add a delay between pages when paging multiple pagers to allow the repeater time to repeat the signal and detect the next one Default setting is OFF To add repeat Delay e Press PROG PROG 6 e Press 10 for More e Press 10 for repeater At rPt press 6 for ON to enable the Repeat Delay Press 10 for OFF to disable Repeat Delay If done press 6 for Yes if not press 10 for No Duty Pager The duty pager is used to remind someone of a periodic repetitive task To setup e Press PROG PROG 7 At duty Press 6 for On After2. Down scroll button scroll until display shows Auto ON OFF 2 Press Read Select to set auto on off 3 Use the Up or Down scroll button to select On or Off 4 Press Up or Down scroll button to set on off time and press Read Select to move through the seg ments Set Key Tone On Off 1 Using the Up or Down scroll button scroll until display shows Set Key Tone 2 Press Read Select to set key tone on off 3 Use the Up or Down scroll button to select On or Off 4 Press Read Select to set Long Range Systems 28 T9101 amp Cancel Panel User Manual Select Alert 1 Using the Up or Down scroll button scroll until display shows Set Alert Mode 2 Use the Up or Down scroll button to select Beep Vibe Off 3 Press Read Select to set Beep Use the Up or Down scroll button to select e Select Loud or Soft and press Read Select to set e Select Duration seconds and press Read Select to set Vibe Off Use the Up or Down scroll button to select e Press Read Select to set Long Range Systems 29 T9101 amp Cancel Panel User Manual Using the Star Pager 14 a a O O O gt E Charging Any rechargeable pager will require use of an LRS charger The Star Pager SP4 uses the Charger 9 CH R9 1 Place the pager in the charger 2 Allow unit to charge fully overnight at least 24 hours 3 Remove from charger and pager will vibrate beep and light 4 Replace the pager in the cha
3. the clean rag with the isopropyl alcohol cleaner 3 Wipe down the pagers or equipment Cleaning equipment with any other non approved cleaners can weaken plastic and cause hairline cracks Pagers and equipment that are cleaned with unapproved clean ers and suffer cracking will not be covered under warranty Do not submerge any LRS paging equipment in any type of liquid as this will also dam age the equipment and is not covered under the standard warranty Charging Place rechargeable pagers on the charger and let them charge for 8 hours prior to first use Rechargeable pagers should be kept on charge even during extremely long periods of inactivity Only 10 VAC power supplies should be used with LRS chargers and transmitters DC power supplies will cause damage to equipment that is not covered under the standard warranty Should you have any questions please contact the LRS Customer Service Department at 800 437 4996 Long Range Systems 31 T9101 amp Cancel Panel User Manual Warranty Long Range Systems Inc warrants this product against any defects that are due to faulty material or workmanship for a two year period after the original date of consumer purchase This warranty does not include damage to the product resulting from accident misuse or improper electrical connection If this product should become defective within the war ranty period we will repair or replace it with an equivalent product free of charge LRS will
4. 10 seconds the screen will default to Off Enter the Duty Pager number with the keypad then press ENT e Enter Vibe Level value of 1 2 or 3 then press ENT e Enter the re page time as hh mm hours minutes then press ENT e Screen will briefly display the new settings If done press 6 for Yes if not press 10 for No To disable the Duty Pager e Press PROG PROG 7 e At duty Press 10 for Off If done press 6 for Yes if not press 10 for No Restaurant ID The ID of the Restaurant system Set if more than one LRS system is in an area to prevent interference To set e Press PROG PROG 14 At rest ID enter a value from 0 to 9 and then press ENT If done press 6 for Yes if not press 10 for No Long Range Systems 13 T9101 amp Cancel Panel User Manual Station ID The station that will be displayed on a pager if more than 1 station is in use To set e Press PROG PROG 11 e At stn ID enter a value from 0 to 9 and then press ENT If done press 6 for Yes if not press 10 for No POCSAG FM Start e Press PROG PROG 8 e Select FM Start by pressing 1 Note A 10 second delay will default to FM Start e Set the start point at value from 00 to 99 and then press ENT If done press 6 for Yes if not press 10 for No Edit Manager Pager Number In the event the Manger s pager numbers are changed to change the T9101 e Press PROG PROG M1 or M2 At MGR1 num enter the new
5. 9100 and T9100CP paging transmitters and on site pagers comply with the essential requirements in the European RE amp TTE Directive 1999 5 EC of the European Parliament of the Council of 9 March 1999 on radio equipment and telecommunication terminal equipment and the mu tual recognition of their conformity The following standards were utilized ETS 300 224 1998 EN 301 489 2 2002 EN61000 3 2 1998 EN 61000 3 3 1995 EN 60950 1992 with A1 A2 amp A3 XU 0035 12 04 09 Long Range Systems 32 T9101 amp Cancel Panel User Manual Long Range Systems UK Ltd Link House Leek Road Milton Stoke on Trent Staffordshire ST2 7AH 01782 537000 www Irspagers co uk www pagers co www hospitalpagers co uk
6. T9101 Cancel Panel Paging System Transmitter USER MANUAL A LY WWW pager net DOC eo COSSsoce Installation Warranty and Service Information Long Range Systems UK Ltd Link House Leek Road Milton Stoke on Trent Staffordshire ST2 7AH 01782 537000 www Irspagers co uk www pagers co www hospitalpagers co uk Table Of Contents The 19101 cna sweohenad sc ake niet ats wee et okie ee wee eae ess 3 EEL FS Ce tee 3 Hardware Provided ac c00 e ad ceed Aa a eee a a wee Hae Seed 2 3 Optional HardWare eie ceca iio o weed een eddie knee Redden we Ce A 3 Hardware Setup Procedure 0 0c eee eee tenet nee 3 Overview of T9101 o ee a ee ee eee ee ee 7 Keypad eeneg nr da doi Ga eee a E A a 7 Antenna sa em rl e ts e E 8 Rest TECMINANS io fave een a a a rra a 8 Status LED 20 iii A a de 8 System Specifications oooooocoococoo eee eens 8 Using the T9101 o cu se ee ee ee a ee ee ee ee ee eae ee es ee 9 Time and Date mese id ao Seed aes Sate al tek tive dae Se aed 9 Pag stats daa nae hw Ree taba eda aa debate heed ee 9 Cancel Page edie caia aera ica aber alte a a a EEDAN 9 User Preferences 00000 ees 10 Display Current Settings 0 ccc tenet eens 10 PMU OR rerit s sieaas Wis AA aoe we EM Na Ed ele E 10 Display Clock ase odessa se acecwsd di a usd pil dd wee wee 2 11 VIDE LEVEL ici dae a e ee A ee eee a Reda OY ee ee koe 2 11 ROW LOC oscar a add dd o ede ce 11 Preset Message rca ar
7. a a e denote 12 FRE PO AIG eii ads ii ada do ea a te Se Eten ee 13 Repeater Delay cobol rata e 13 PUY RAGE sumen alo pase ero ia po oe 13 RestaurantiD cocos a e ao 13 Station D cria a id ta 14 POCSAG FM Staf ers repare re ee 14 Edit Manager Pager Number 0 occccccccc c eee tee 14 Reset to Factory Default 0 ccc ce eee nen eens 14 Server Statistics cone se e a de lesa cies ale mate be a Suave Seen 14 RANGE IESE ini be ai apaia et eid 2 hed Meee ane Oe a ete ae eee 16 iaio MID Aa ano sets ee o Sareea aS ues set es Sees eet ees 16 Pager Programming 0 o 17 T9100 Cancel Panel 2 2 0 eee ee 18 Overview of T9100 Cancel Panel 0 ccc eee eee eee 18 Long Range Systems 1 T9101 amp Cancel Panel User Manual Rey Pad siseste pienaari a a tt aad a 18 Using the T9100 Cancel Panel ooooo ooo o 19 Paging craige Er ras ee bees ee easel tio std ias E 19 Cancel Page ec A A a A e 19 User Preferences 0020 asmanni tana eee 20 Paging from Cancel Panel 00 ccc eee eee 20 Associating the T9100 Cancel Panel to T9101 2200000 2 eee 21 Setting T9100 Cancel Panel as UHF Master 222000002 eee 22 Service Questions and Answers oooo ooo ooo o 23 LRS PAGERS AVAILABLE FOR THE T9101 o 24 USING THE SP5 00200 e dt is Be ee ee i ee ee ee eee dc 24 CHAOIN cancelados dread dada atic aes apes ide 24 MENUS estaria Moe hii dG Doe Rha de beade
8. ber Keys Status LED Bt sci QOVOQ IKK Reset Terminals Function Keys Vibration Keys Keypad Function Keys The function keys are located along the bottom row of the T9101 gt 30 used to page pagers whose number is 31 through 99 M1 amp M2 used to page and program Manager Pagers 86 All Call button used to page all pagers CLR used to clear an entry or to back up one menu level PROG press once to program pagers press a second time to access the menu functions ENT used to enter functions Vibration Keys V1 V2 and V3 select the number of vibrations a pager will respond with This button is pressed before pag ing a pager Sends message 1 2 or 3 to Alpha pagers Number Keys Number keys 1 through 30 located along the center row Number 10 is also 0 when Programming using the Menus or paging pagers greater than 30 Long Range Systems 7 T9101 amp Cancel Panel User Manual Antenna The T9101 utilizes 2 antennas when transmitting A UHF antenna located to the user s left is used to communicate with the LRS pagers A 2 4 GHz antenna located to the user s right communicates with the T9100 Cancel Panel Reset Terminals The Reset Terminals are located to the user s left side on the transmitter These are used to reset a pager for programming Status LED This LED will light green to indicate that the T9101 is sending information to the pagers or T9100 Cancel Panel System Specificati
9. conds to match the displayed time of the T9101 to within about a second Repeat steps 6 through 12 for additional Cancel Panels Long Range Systems 21 T9101 amp Cancel Panel User Manual Setting 19100 Cancel Panel as UHF Master The Cancel Panel can be set to act as the UHF Master of a system of T9101 and other Cancel Panels to page LRS Pagers To enable the Cancel Panel as UHF Master e Press PROG PROG 1 8 ENT e Press the button under Yes to select Yes If done select Yes button under Yes if not select No button under No To enable the T9101 as UHF Master e Press PROG PROG 18 e Press the button under Yes to select Yes If done select Yes button under Yes if not select No button under No Long Range Systems 22 T9101 amp Cancel Panel User Manual SERVICE QUESTIONS AND ANSWERS Should your paging system ever fail or should you need additional paging supplies call Long Range Systems at 800 437 4996 Normal Business Hours Monday Friday 8 30 am to 5 00 pm Central Time Weekend or Night Emergencies e Long Range Systems has 24 7 live technical support available e Please keep in mind that replacement options are limited over the weekend Long Range Systems 23 T9101 amp Cancel Panel User Manual LAS PAGERS AVAILABLE FOR THE 18101 These pagers are sold separately SP5 Rechargeable Alpha LRS Alpha E467 Star Rechargeable Pager USING THE SPO Sel
10. d Le bod Sade Td 24 SOMO Sica nta ura Huns ake doi T ia rod 26 Messages 2420 cng be ricardo roo ira 26 e TO 26 Reprogramming and Reset o ooccocoooo eee eee 26 USING THE LRS ALPHA E467 22 2 eee ee 27 AENA Gace aimed iu CEEE aoe gee alter EEE EAEE eevee mde 2 27 Power On Off tesos eaei de 27 Read Messag cion Cow i a e a e aon 28 Delete Messages cece eee eee tee 28 Time Date Set 2 2650 nd aiai td we aero de ed 28 SEL COMUASE pateo cue adan oa dias papas 28 Auto ON OFF ui lt inka eie ind Gb eee ad ea hace ee ww eke 28 Set Keytone On Off 0 ccc eee tenet e eens 28 Select Alert 2 040008 deca ett Drews ti oe ei mea eee sd 29 USING THE STAR PAGER 2 02 e eee eee ee ee 30 Charging ea esis Sere ethan se shed ale A Secon be ms Reels REER ated ENSEDE 30 Messaging de orcas re e e aE 30 Cleaning Charging Instructions for LRS Paging Equipment 31 Warranty sic ni ma la a a a si lc sc S i aa 32 Long Range Systems 2 T9101 amp Cancel Panel User Manual THE 19101 Installation Hardware Provided Each transmitter kit contains the transmitter Instruction Booklet two antenna one 10VAC 1 5A power adap tor one Staff Name board and four mounting bracket kits Optional Hardware The T9101 and T9100 Cancel Panel have the ability to print a server report to a POS Printer Contact LRS if you wish to purchase a printer Hardware Setup Procedure 1 Remove all items from their
11. ease to wards the minimum 6 Release the Select Button when desired vibration level has been reached 7 To exit wait 8 seconds and the pager will go back to the vibe contrast menu VIBE CONTRAST Contrast To setthe Contrast Level 1 Remove the pager from the charger 2 While vibrating or beeping press and hold the Select Button for 5 8 seconds 3 Highlight the Contrast selection then PRESS and HOLD the Select Button until the screen shows CONTRAST 4 Press or hold the Select Button until the desired contrast is selected 5 If holding down on the Select Button the contrast level will increase to Max NOTE screen could be dark and hard to read 6 Release the Select Button and press or hold again to change the level back towards the minimum or until your desired contrast is selected 7 To exit wait 8 seconds and the pager will go back to the vibe contrast menu VIBE CONTRAST 8 To exit this menu wait 8 additional seconds Long Range Systems 25 T9101 amp Cancel Panel User Manual Settings To view the current pager settings 1 Remove pager from the charger or reset on the T9601 T9100 or T9101 reset terminals 2 Press the Select Button repeatedly to scroll through the settings C1 System ID number and Pager ID number C2 System ID number and All Page number C3 System ID number and System ID number G Group number Enc Encryption enabled 128 or none Ver Current Firmware Ver
12. ect Button www pager net s Charging Any rechargeable pager will require use of an LRS charger The SP5 uses the Charger 5 CH R5 1 Place the pager in the charger 2 Allow unit to charge fully overnight at least 24 hours 3 Remove from charger and the pager will vibrate or beep 4 The LCD will show e C1 System ID Pager ID Ex C1 0 91 e Programming Active e Blank screen or Date and Time if set Ex 10 07 2008 12 05 am 5 Return the pager to the charger at the end of each day Menus To access the vibe contrast menu 1 Remove the pager from the charger 2 While vibrating or beeping press and hold the Select button for 8 seconds The menu will display VIBE CONTRAST Long Range Systems 24 T9101 amp Cancel Panel User Manual 3 If you PRESS and RELEASE the Select Button the menu selector will scroll to the right and will high light Contrast VIBE CONTRAST 4 To exit this menu wait 8 seconds 5 To re enter the vibe contrast menu at anytime repeat Step 1 Vibe To set the Vibration Level 1 Remove the pager from the charger 2 While vibrating or beeping press and hold the Select Button for 5 8 seconds 3 Highlight the Vibe selection then PRESS and HOLD the Select Button until the screen shows 4 Press or hold the Select Button until the desired vibration level is selected VIBE 5 If holding down on the Select Button the vibe level will increase to max and then decr
13. end by pressing 10 At Auto press 6 for ON If done press 6 for Yes if not press 10 for No To disable e Press PROG PROG 1 e Select send by pressing 10 At Auto press 10 for OFF If done press 6 for Yes if not press 10 for No Paging 1 To page pagers 1 through 30 press the pager number and the unit pages automatically 2 To page pagers 31 through 99 e Press gt 30 Enter the pager number up to 99 using 1 9 and 10 as zero e Press the ENT key All Call If all staff pagers need to be called at once press the 86 key Manager Pagers To page the managers press the M1 for the 1 manager pager or M2 for the 2 manager pager Cancel Page To clear cancel a pager to the server e Press CLR pager Long Range Systems 9 T9101 amp Cancel Panel User Manual User Preferences The T9101 will come with factory settings for normal operating use Some features can change per the user s custom needs Display Current Settings To view the current settings for the transmitter e Press PROG PROG 16 e Press ENT to scroll through each item e Date e Restaurant ID Number e Station ID Number e FM Start point e Pre canned Message e Repage interval e M1 Manager 1 information e M2 Manager 2 information e Duty Pager information e Cancel Panel set to page yes or no Note Only seen on Cancel Panel e UHF Master T9101 is set to Master yes or no e Joined or Not Joined e Pan and C
14. hannel ID e Node ID e Channel Scan is on or off e Synched on or off e Beeper keytone is on or off e Code Version e Error Count If done press 6 for Yes if not press 10 for No Antitheft Note This feature is ONLY for text pagers This feature will make a pager beep and or vibrate continuously if goes beyond the range of the transmitter To enable e Press PROG PROG 4 At theft press 6 If done press 6 for Yes if not press 10 for No To disable e Press PROG PROG 4 At theft press 10 If done press 6 for Yes if not press 10 for No Long Range Systems 10 T9101 amp Cancel Panel User Manual Display Clock The default setting for the clock is ON during normal operation To disable e Press PROG PROG 10 e Press 10 to select the Clock sub menu e At cloc press 10 If done press 6 for Yes if not press 10 for No To enable e Press PROG PROG 10 e Press 10 to select the Clock sub menu e At cloc press 7 If done press 6 for Yes if not press 10 for No Vibe Level The default Vibration Level for pagers can be set via 1 Pressing the V1 V2 or V3 buttons for levels 1 2 and 3 respectively 2 From the menus e Press PROG PROG 12 e Enter a value of 1 2 or 3 from the keypad If done press 6 for Yes if not press 10 for No Keytone The transmitter default is for tones to sound with each key press To disable e Press PROG PROG 22 At beeper pre
15. if not select No button under No To enable e Press PROG PROG 1 7 ENT e At CP Paging press the cancel button under ON If done select Yes button under Yes if not select No button under No Long Range Systems 20 T9101 amp Cancel Panel User Manual Associating the 19100 Cancel Panel to 19101 oor WN Apply power to T9101 and allow it to boot up Press PROG PROG 19 and then press 10 to Set the channel Input a channel between 11 and 26 and then press ENT Press ENT to accept Pan ID Allow T9101 to reset While T9101 is resetting on T9100 Cancel Panel apply power to the Cancel Panel and allow it to boot up 7 Press PROG PROG 1 9 ENT and then press the button under SET to Set the channel 11 q Note If the Cancel Panel fails to join the display will show Attempt Fail Note The channel and 12 13 Enter the same channel as set on T9101 then press ENT Press ENT to accept Pan ID On T9101 press PROG PROG 29 to start Associate mode NOTE The T9101 will stay in Asso ciate for 2 minutes On Cancel Panel press PROG PROG 2 9 ENT to start Associate mode When the Cancel Panel associates it will display e Attempt Join e PAN Found e Then display channel and Pan ID Pan ID of the T9101 and Cancel Panel must match to associate After associating Exit by pressing CLR The time displayed on the Cancel Panel should take about 10 se
16. manger number from the keypad value from 0 to 99 then press ENT e Enter the Vibration Level Value of 1 2 or 3 then press ENT If done press 6 for Yes if not press 10 for No Reset to Factory Default A R Note Caution If you reset the T9101 to factory defaults the system ID vibration mode and sta x tion ID could be reset and you may have to re set these to work with your exist ing pagers If you still want to proceed with this function do the following e Press PROG PROG 21 At reset press 6 for Yes Press 10 for No to keep current settings If done press 6 for Yes if not press 10 for No Server Statistics The T9101 can track the daily statistics of the number of times a server was paged the server s average re sponse and the number of times a manager is paged To enable Server Statistics e Press PROG PROG 23 e At Stats select ON Enter the start time example 3 for 3 AM or 3 PM and then press ENT e Select AM or PM e The transmitter s memory will clear If done press 6 for Yes if not press 10 for No Notes At the set time the daily report will print to the POS Printer At the set time the memory will also clear to begin a new set of daily statistics To disable the Server Statistics e Press PROG PROG 23 e At Stats select OFF If done press 6 for Yes if not press 10 for No Long Range Systems 14 T9101 amp Cancel Panel User Manual dis e
17. mp Cancel Panel User Manual Using the 19100 Cancel Panel Paging To page pagers 1 though 99 enter the 2 digit number of the pager The transmitter can page up to 16 pagers at one time without using the 86 all call button When paged the pager number will show on Cancel Panel display If not canceled the pager number will begin to flash after the first re page time expires The pager number will flash faster after the second re page time expires Cancel Page To Cancel a page press the Cancel Key immediately under the number of the pager If using a Cancel Panel with T9101 the pager number may be canceled from the Cancel Panel or by press ing CLR then the pager number on the T9101 Long Range Systems 19 T9101 amp Cancel Panel User Manual User Preferences The T9100 Cancel Panel operates as a Slave to the T9101 Many settings are transmitted to the Cancel Panel via the T9101 To edit preferences refer to the User Preferences of the T9101 Note To enter selections greater than 10 the user will need to enter as two numbers Example enter 15 by pressing 1 and then 5 Paging from Cancel Panel This feature enables or disables the Cancel Panel from paging pagers This feature is only available and only set on the Cancel Panel The default setting is On to page pagers To disable e Press PROG PROG 1 7 ENT At CP Paging press the cancel button under OFF If done select Yes button under Yes
18. nd replace battery 4 Press PROG ENT is the pager number 1 through 99 5 After the pager responds page it to ensure it programmed okay e Star pagers will do one glow mode cycle e Alpha pagers will beep 4 times For Manager Pagers 1 Be sure to set the T9101 for the System ID in use 2 Be sure the POCSAG FM start is correct for the pagers in use Long Range Systems 17 T9101 amp Cancel Panel User Manual 18100 CANCEL PANEL Overview of T9100 Cancel Panel Antenna Cancel Keys www pager net CANCE PANEL Power Supply Reset Terminals Function Keys Number Keys Vibration Keys Keypad Function Keys The function keys are located along the bottom row of the Cancel Panel M1 amp M2 used to page and program Manager Pagers 86 All Call button used to page all pagers CLR used to clear an entry or to back up one menu level PROG press once to program pagers press a second time to access the menu functions ENT used to enter functions Vibration Keys V1 V2 and V3 select the number of vibrations a pager will respond with This button is pressed before pag ing a pager Sends message 1 2 or 3 to Alpha pagers Cancel Keys The row of keys located below the display These keys will cancel a call to the pager number shown on the display immediately above the respective key The Cancel Keys also are used during menu selection Long Range Systems 18 T9101 a
19. ng nuts to the clamps 2 Use the 10 32 x 3 8 screws to hold the clamps Do not fully tighten screws Clamp Captive Nuts Screws r 3 Adjust the distance between clamps G until fits to the mounting surface 4 Tighten screws _ Long Range Systems 4 T9101 amp Cancel Panel User Manual 5 Place the thumbscrew into the clamp op posite the one with the foam pad 6 Attach the foot of the thumbscrew 7 Adjust position of thumbscrew and tighten to hold the transmitter in place Clamp with Foam Pad Z A Thumbscrew A A Foot A Aa A A eS a a Ee E ES EA ES Thumbscrew Turn clockwise to tighten Turn counter clockwise to loosen Because the thumbscrews and brackets can be mounted in many ways they can be adapted to most locations O Thumbscrew Mounting Bracket Horizontal Mount Mounting Screws Vertical Mount Thumbscrew Mounting Bracket E A Mounting Screws Long Range Systems 5 T9101 amp Cancel Panel User Manual Power Connection 1 Plug the power supply into a standard 110V outlet and the barrel connector end into the jack on the side of the transmitter 2 Upon completion of the setup make sure pagers are fully charged Long Range Systems 6 T9101 amp Cancel Panel User Manual Overview of 19101 Antenna Num
20. nge of the T9101 in your environment To start the range test e Press PROG PROG 8 e Select range by pressing 10 The Range Test will begin automatically Stop the Range Test by pressing any button If done press 6 for Yes if not press 10 for No Find ID e Press PROG PROG 10 e Select ID by pressing 1 Note A 10 second delay will default to ID e To start locating the ID press 7 for Yes To not locate the ID press 10 for No e The transmitter will begin by transmitting on ID O zero If the pager received the page at the prompt receive press 7 for Yes If not press 10 for No The transmitter will automatically in crement to the next ID and page Repeat this step until the pager receives the page If done press 6 for Yes if not press 10 for No Long Range Systems 16 T9101 amp Cancel Panel User Manual Pager Programming Star and Alpha Pagers can be reprogrammed from the T9101 transmitter If the pagers need to have their identification code reprogrammed contact LRS before proceeding The following is the basic procedure to use For Server Pagers 1 Be sure to set the T9101 for the System ID in use 2 Be sure the POCSAG FM start is correct for the pagers in use 3 Reset the pager e Rechargeable pagers are removed from the charger or touched to the reset terminals They stop vibrating when reset is complete e Battery powered pagers reset when turned off and then back on or remove a
21. ons Notice Operation is subject to the following e This device may not cause interference e This device will accept any interference including interference that may cause undesired oper ation of the unit Required Voltage One 110 220V outlet for the T9101 transmitter Operating Frequency 420 470 MHz Radiated Power lt 4900 micro volts meter Operating Range Dependent upon pagers used Long Range Systems 8 T9101 amp Cancel Panel User Manual Using the 19101 Time and Date Initial Power Up During power up to enter the time and date At enter time enter the hh mm hour minute using the number keys and then press ENT e Press 2 for AM or 10 for PM e At date enter the mm dd yy month day year using the number keys and then press ENT Clock Menu The time and date can also be set from the Clock menu by e Press PROG PROG 1 Select set by pressing 6 At enter time enter the hh mm hour minute using the number keys and then press ENT e Press 2 for AM or 10 for PM At date enter the mm dd yy month day year using the number keys and then press ENT e If done press 6 for Yes if not press 10 for No Note The transmitter will use a default selection of Yes after 30 seconds of inactivity Send Time This feature will automatically send the current time and date to the pagers every 15 minutes The default setting is OFF To enable e Press PROG PROG 1 e Select s
22. packaging 2 Locate the silver connector on the top of the transmitter Twistthe antenna about 3 long BNC silver bottom onto the connector 3 Locate the gold connector on the top of the transmitter Twist the antenna about 4 long SMA bends at right angle onto the gold connector Note Both antennas must be attached before turning on transmitter Do not remove either antenna at any time due to risk of damage 4 Mount the power supply in convenient location with access to 110V power Mounting the Transmitter The T9101 is designed to be mounted in various ways to accommodate the kitchen environment to a hori zontal surface i e table counter shelf to a vertical surface or hanging to a wall or stand Caution Mounting with the antenna near any large metal objects will degrade the operating range To place on a wall or stand locate the four slots on the mounting plate Then align four wall anchors 5mm diameter into the wall to the mounting plate Panel and Wall Mount Mounting Holes Long Range Systems 3 T9101 amp Cancel Panel User Manual For mounting to surfaces place the mounting brackets into the captive nuts for either horizontal or vertical mounting There are two sets of 4 cap tive nuts for mounting to horizontal surfaces and one set of captive nuts for mounting to vertical surfaces Captive Nuts To attach the clamps 1 Align the mounti
23. pose nor does LRS Inc assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages Typical parameters that may be provided in LRS Inc data sheets and or specifications can and do vary in different applications and actual performance may vary over time All operating parameters including Typicals must be validated for each customer application by customer s technical experts LRS Inc products are not designed intended or authorized for use as components in sys tems intended to support or sustain life or for any other application in which the failure of the LRS Inc product could create a situation where personal injury or death may occur Should Buyer purchase or use LRS Inc products for any such unintended or unauthorized application Buyer shall indemnify and hold LRS Inc and its officers employees sub sidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unau thorized use even if such claim alleges that LRS Inc was negligent regarding the design or manufacture of the part de vice or system EU DECLARATION OF CONFORMITY We Long Range Systems hereby declare under our sole responsibility that the T
24. return your product via UPS ground shipping All warranty claims must be initiated through our customer service department Copyright August 2009 Long Range Systems Inc All Rights Reserved This manual contains proprietary information of Long Range Systems Inc LRS and is intended for use only by its em ployees or customers None of the material contained herein may be copied reproduced republished downloaded dis played posted or transmitted in any form or by any means including but not limited to electronic mechanical photocopying recording or otherwise without the prior written permission of LRS Additional copies of this manual may be obtained by contacting LRS Screen displays keyboard layouts hardware descriptions or software are proprietary to LRS and are subject to copy right and other intellectual property rights of LRS and shall be treated in accordance with the previous paragraph All attempts have been made to make the information in this document complete and accurate LRS is not responsible for any direct or indirect damages or loss of business resulting from inaccuracies or omissions Specifications and other information contained within this document are subject to change without notice Long Range Systems Inc reserves the right to make changes without further notice to any products herein LRS Inc makes no warranty representation or guarantee regarding the suitability of its products for any particular pur
25. rger at the end of each day Messages The pager can vibrate beep and light up message lights e Star pagers are intended to vibrate the number of times determined by the Vibe mode selected On the T9101 this is done by choosing the V1 V2 or V3 button This can be a way to send ad ditional information or to identify 1 of 3 stations e On the front of the pager are four lights 1 through 4 In normal operation each station or T9101 would be set for different STATION ID s e g kitchen is station 1 etc Each station will also send different messages example 1st light for station 1 2nd light for station 2 4th and 1st light for station 5 etc So ifthey were paged they can look down atthe pager to see which sta tion sent the message which light was lit As an option you can also send the message as a V1 for a station one message or V2 for station 2 or V3 for station 3 This will enable the per son being paged to avoid having to look down to see the lights Long Range Systems 30 T9101 amp Cancel Panel User Manual Cleaning amp Charging Instructions For LAS Paging Equipment Cleaning LRS pagers are made from industrial strength polycarbonate material However this material is susceptible to hairline cracking if non approved cleaners are used When clean ing LRS pagers we recommend only using ISOPROPYL ALCOHOL BASED CLEANERS To clean the equipment 1 Take a clean rag and an isopropyl alcohol based cleaner 2 Soak
26. sa 9 Note Server Stats needs to be turned ON before Stats can be viewed or printed The current POS Printer supported for the T9101 is the Star TSP650 Attach the DB25 to DB9 adapter between the printer and the serial cable Then connect the serial cable to the serial port of the T9101 To print a current view of the Server Statistics e Press PROG PROG 24 e Enter a server number and press ENT e Select PRINT e The statistics will now print If done press 6 for Yes if not press 10 for No Note The Statistics will also print at the time set in the Stats menu Example Print Date Time Server Response Report Svr Pages A R T Mgr 1 5 00 44 02 5 4 00 29 01 12 3 00 15 17 4 00 25 01 Svr Server Pager of pages in last 24 hours A R T Average Response Time Mgr of times manager was paged Viewing Statistics To View the current Server Statistics e Press PROG PROG 24 e Enter a server number and press ENT e Select VIEW e Press ENT to scroll through the list of servers The list will start at the number entered and will continue to the end of the list or until CLR is pressed If done press 6 for Yes if not press 10 for No Long Range Systems 15 T9101 amp Cancel Panel User Manual Example Statistics View Servers of Pages in Average of Times 24 hr Period Response time Manager Paged mm ss 1 05 00 44 02 Range Test This can be used to determine the effective ra
27. se Up or Down Scroll button to select YES 3 Press Read Select button to set Set OFF 1 Using the Up or Down scroll button scroll until display shows Power OFF 2 Press Read Select button to set power on off 3 At Power OFF screen use Up or Down Scroll button to select YES 4 Press Read Select button to set Long Range Systems 21 T9101 amp Cancel Panel User Manual Read Message ts tow 46 0102 2008 SCROLL UP 40 04 AM Appel Telephonique SCROLL DOWN e Messages are displayed upon receipt e Press Read Select to display To review stored messages 1 Select Read All 2 Press Read Select to display messages and time stamps 3 Use the Up or Down Scroll button to scroll through messages Delete Messages 1 Using the Up or Down scroll button scroll until display shows Delete All 2 Press Read Select 3 Use the Up or Down scroll button to select Yes or No 4 Press Read Select button to confirm Time Date Set 1 Using the Up or Down scroll button scroll until display shows Set Time Date 2 Press Read Select to set time date 3 Press Up or Down scroll button to set each time or date segment and press Read Select to move through the segments Set Contrast 1 Using the Up or Down scroll button scroll until display shows Set Contrast 2 Press Read Select 3 Use the Up or Down scroll button to adjust 4 Press Read Select to confirm Auto ON OFF 1 Using the Up or
28. sion 3 To exit wait 8 seconds Messages The pager stores the last 5 received messages To view the messages 1 At the blank screen time amp date menu display press the Select Button once 2 Messages 2 lines in length will show a gt symbol at the end of the first line and a lt symbol at the be ginning of the second line 3 Messages over 2 lines in length the middle lines will show lt the next line of the message gt 4 Press the Select Button to continue scrolling forward through the message or messages Time Pager will display the current time This feature is automatically updated by the T9101 transmitter Ifthe time does not appear a flashing star will appear on the right side of LCD to show pager is operational Reprogramming and Reset To reset and reprogram the pager see Pager Programming of this document Long Range Systems 26 T9101 amp Cancel Panel User Manual USING THE LAS ALPHA E46 SCROLL UP wwwpasernet Rs SCROLL DOWN SELECT READ BUTTON Menus 12 SCROLL UP Read All 10 25 10 38am SCROLL DOWN Selecting functions 1 From Read All screen press Up or Down Scroll button until desired selection displays 2 Press Read Select button to select item 3 Press Up or Down Scroll button to choose adjust 4 Press Read Select to confirm set Power On Off Set ON if unit is off 1 Press and hold Scroll Up until YES NO shows 2 At Power ON u
29. ss 10 If done press 6 for Yes if not press 10 for No To enable e Press PROG PROG 22 At beeper press 6 If done press 6 for Yes if not press 10 for No Long Range Systems 11 T9101 amp Cancel Panel User Manual Preset Message The LRS transmitters come with a list of preset messages that can be sent to Alpha Pagers To edit which message is sent e Press PROG PROG 13 Enter the preferred message from the table then press ENT If done press 6 for Yes if not press 10 for No Pre Loaded Messages 000 Phone Call 020 Starter 040 Door 060 Car 001 Sales Call 021 Service drive 041 Survey 061 Bus 002 Manager 022 Showroom 042 T nnn O mm 062 Bay 003 Customer 023 Parked Call 043 Break 063 Low battery 004 Room 024 Voice Mail 044 Fire 064 Error 005 Visitor 025 Dressing room 045 Unit 065 Exit 006 call Ext 026 Price check 046 Window 066 Fax 007 MTG Room 027 Department 047 Nurse 067 host 008 Lane 028 Cashier 043 Register 068 Space 009 Aisle 029 Office 049 Owner 069 Location 010 Void 030 Table 050 Check 070 Nursery 011 Stamps 031 Winner 051 Drink 071 Teller 012 Change 032 Pickup 052 Food 072 Officer 013 Station 033 Dock 053 Service 073 Buffet 014 Machine 034 You have mail 054 Seat 074 Diaper change 015 Operator 035 Table ready 055 Booth 075 Child crying 016 Emergency 036 No special 056 Lobby 076 To nursery 017 XX Minutes 037 Hole 057 Help 018 Tee 038 Kitchen 058 Restroom 019 ProShop 039 Bar 059 Valet
Download Pdf Manuals
Related Search