WSG08POE User Manual
Contents
1. Tree IEEE 802 1w Rapid Spanning tree protocol LACP provides a loop free network and redundant links to the core network with rapid convergence to ensure faster recovery from failed links enhancing overall network stability and reliability RSTP System Configuration gt System Priority This parameter configures the spanning tree priority globally for this switch The device with the highest priority becomes the STP root device However if all devices have the same priority the device with the lowest MAC address becomes then the root device gt Hello Time Interval in seconds at which the root device transmits a configuration message BPDU frame Number between 1 10 default is 2 gt Max Age The maximum time in seconds a device can wait without receiving a configuration message before attempting to reconfigure It also means the maximum life time for a BPDU frame Number between 6 40 default is 20 gt Forward Delay The maximum time in seconds the root device waits before changing states i e discarding to learning to forwarding Number between 4 30 default is 15 K Force Version Set and show the RSIP protocol to use Normal use RSTP Compatible compatible with STP Wildix WSGO8POE User Manual 16 RSTP System Configuration System Pronty 32768 Hello Time 2 Max Age 20 Forward Delay 15 Force version Normal Figure 1 8 1 RSTP Port Configuration gt Port The port ID It cannot be changed2. a packet to travel from this port to the root in the current Spanning Tree configuration The slower is the media the higher is the cost gt Edge Port Shows if this port is functioning as an edge port either through manual selection see the RSTP Port Configuration table or auto detection Note that if the switch detects another bridge connected to this port the manual setting for Edge Port will be overridden and the port functions as a point to point connection instead gt P2P Port Shows if this port is functioning as a Point to Point connection The switch can automatically determine if the interface is attached to a pointto point link or to shared media If shared media is detected the switch assumes that it is connected to two or more bridges gt Protocol Shows the spanning tree protocol functioning on this port either RSTP or STP STP compatible mode RSTP VLAN Bridge Overview RSTP VLAN Bridge Overview VLAN Id Bridge Id Hello Time Max Age Fwd Delay Topology Root Id 1 32769 00 03 ce 09 3c 8f 2 20 15 Steady This switch is Root Refresh and RSTP Port Status Port Group Vlan Id Path Cost Edge Port P2p Port Protocol Port State Poe ee ee Nasr Pot HEE ros Mam Pots S Mm Pots Mam Pats Mam Pas O O o Ha Figure 2 4 2 gt Hello Time Interval in seconds with which the root device transmits a configuration message Wildix WSGO8PO
3. at the rear panel of the switch right side shown as below Hardware Installation Set the switch on a large flat space with a power socket close by The flat space should be clean smooth level and sturdy Make sure there is enough of space to attach the cables power cord and allow air circulation Use twisted pair cable to connect this switch to your PC Software Description This part provides you with the information about how to set up and manage the switch through the web user interface Open the web browser and type in the URL 192 168 2 1 You see the login screen The factory default did not set up a password so you can just click the Apply button The login process is completed and Password successfully entered appears on the screen Login Please enter password to login Password Apply Password Successfully Entered Figure 1 1 Wildix WSGO8POE User Manual 8 Aher the user login the right side of website shows all functions Fig 1 2 Figure 1 2 Configuration Administrator System Configuration This page shows system configuration information Wildix WSGO8POE User Manual System Configuration Figure 1 3 gt MAC Address hardware address assigned by manufacturer default gt S W Version switch s firmware version gt H W Version switch s Hardware version gt DHCP Enabled click to enable DHCP gt Fallback IP address assign the IP address manually the default
4. can be installed where the space is limited moreover it provides smooth network migration the network capacity can be upgraded easily In addition the switch has comprehensive features such as QoS Quality of Service Spanning Tree VLAN Power over Ethernet PoE Link Aggregation SNMP IGMP Snooping capability via the intelligent software It is suitable for both metro LAN and office application Web Management Features Configuration Administrator Ports Configuration VLAN Setting Trunking Link Aggregation Raid Spanning Tree IGMP Snooping Port Mirroring QoS Setting PoE Configuration Storm Control Monitoring Statistics Overview Detailed Statistics LACP Status RSTP Status IGMP Status VeriPHY Ping Maintenance Reboot Device Warm Restart Load Default Setting Factory Default Firmware Updating Software Upload Backup Recovery Configuration File Transfer Wildix WSGO8POE User Manual 4 Logout Specifications gt Standard IEEE 802 3 10BaselT IEEE 802 3u 100BaseTX IEEE 802 ab 1000BaseT IEEE 802 af Power over Ethernet IEEE 802 3at IEEE 802 3z 1000BaseSX LX IEEE 802 3x Full duplex Flow Control IEEE 802 3ad Link Aggregation IEEE 802 1Q VLAN IEEE 802 1d Spanning tree protocol IEEE 802 1w Rapid Spanning tree protocol IEEE 802 1p Qos gt Number of Port 8 port PoE 10 100 1000BaseT X with 2 Gigabit SFP Open Slots Mechanical gt LED Indicator Port 1 8 Link Act 1000M PoE Port ZFX 8F
5. hash algorithm automatically applies load balancing to the ports in the trunk A port failure within the trunk group causes the network traffic to be directed to the remaining ports Load balancing is maintained whenever a link in a trunk is lost or returned to service Aggregation Trunking Configuration To assign a port to a trunk click on the required trunk number then click Apply Aggregation Trunking Configuration Group Pot 1 2 3 4 5 6 7 8 Normal 8 8 Group 1 o Group 2 Group 3 Group 4 Apply Refresh Figure 1 6 Link Aggregation IEEE 802 3ad Link Aggregation Control Protocol LACP increases bandwidth by automatically aggregating several physical links together as a logical trunk and providing load balancing and fault tolerance for uplink connections LACP Port Configuration gt Port The port number gt Enabled Enables LACP on the associated port gt Key Value Configures a port s LACP administration key The port administrative key must be set to the same value for ports that belong to the same link aggregation group LAG If this administrative key is not set when an LAG is formed i e it has the null value of O this key is automatically set to the same value as the one used by the LAG Wildix WSGO8POE User Manual 15 LACP Port Configuration Port Protocol Enabled Key Value 1 auto auto auto auto auto auto auto N A Ua kd N auto Apply Refresh Figure 1 7 Raid Spanning
6. the VLAN identified by the VLAN tag in the packet If the Packet Type is set to Tagged Only the port drops untagged packets and receives only tagged packets Tagged packets are dropped unless the port is a member of the VLAN identified by the VLAN tag in the packet Switches should be connected to each other with the Packet Type set to Tagged Only PVID The PVID Port VLAN ID is associated with untagged ingress packets It is assigned to untagged frames received on the specified interface The PVID has no effect on ports that have Packet Type set to Tagged Only Default PVID 1 It is not possible to remove a port from VLAN 1 unless its BVID has been changed to something other than 1 Outgoing packets are tagged unless the packet s VLAN ID is the same as the PVID When the PVID is set to None all outgoing packets are tagged Note If you select Tagged Only mode for a port it is recommended to set the PVID to None as the standard configuration Trunking Port trunk allows multiple links to be bundled together and act as a single physical link for increased throughput It provides load balancing and redundancy of links in a switched inter network Actually the link does not have an inherent total bandwidth equal to the sum of its Wildix WSGO8POE User Manual 14 component physical links Traffic in a trunk is distributed across an individual link within the trunk in a method called a hash algorithm The
7. 1 13 2 Wildix WSGO8POE User Manual 24 Monitorning Statistic Overview You can mirror traffic from any source port to a target port for real time analysis the following tigures shows clearly the statistics overview Figure 2 1 Detailed Statics Statistics for Port 1 Figure 2 2 LACP Status Wildix WSGO8POE User Manual 25 LACP Aggregation Overview LACP Aggregation Overview Legend BB dow Port link down o Blocked Port Blocked by RSTP Number is Partner port number d other switch has LACP enabled 0 Leamng Port Learning by RSTP B Forwarding Port ink up and forwarding frames o Forwarding Port link up and forwarding by RSTP Number is Partner port number if other switch has LACP enabled Figure 2 3 1 gt Port Port number gt Port Active Shows if the port is a member of an active LACP group gt Partner Port Number A list of the ports attached to the remote end of this LAG link member gt Operational Port Key Current operational value of the key used by this LAG LACP Port Status RSTP Status Wildix WSGO8POE User Manual 26 RSTP Port Status RSTP Port Status Port Group Vian Id Path Cost Edge Port P2p Port Protocol Port State Port 1 Non STP Port 2 Non STP Port 3 Non STP Port 4 Non STP Port Non STP Port 6 Non STP Port 7 Non STP Port 8 Non STP Figure 2 4 1 gt Port Group The number of a port or the ID of a static trunk gt Path Cost The cost for
8. Aggregations mean any configured trunk group gt Enabled Click on the tick box to enable disable the RSTP protocol for the port gt Edge Expect the port to be an edge port linking to an end station or a link to another STP device gt Path Cost This parameter is used by the STP to determine the best path between devices Therefore lower values should be assigned to ports attached to faster media and higher values assigned to ports with slower media Set the RSTP pathcost on the port Number between O 200000000 O means auto generated pathcost RSTP Port Configuration Port Protocol Enabled Edge Path Cost Aggregations 1 d auto J auto auto d auto auto auto d auto oo w Sod J auto Apply Refresh Figure 1 8 2 Wildix WSGO8POE User Manual 17 RSTP System Configuration System Priority 32768 v Hello Time 7 gt uae 8192 Max Age 42288 Forward Delay been Force version 24576 28672 32768 36864 40960 RSTP Port C 45056 ton 49152 53248 Port 57344 abled Edge Path Cost Figure 1 8 3 RSTP System Configuration System Prionty 32768 Hello Time 2 Max Age 20 Forward Delay 15 Force version Normal lt E atible Figure 1 8 4 IGMP Snooping IGMP Snooping is the process of listening to IGMP network traffic IGMP Snooping as implied by the name is a feature that allows a layer 2 switch to listen in on the IGMP conversation between hosts and routers by processing th
9. E User Manual 27 gt Max Age The maximum time in seconds a device can wait without receiving a configuration message before attempting to reconfigure All device ports except for designated ports should receive configuration messages at regular intervals Any port that age out STA information provided in the last configuration message becomes the designated port for the attached LAN If it is a root port a new root port is selected from among the device ports attached to the network gt Fwd Delay The maximum time in seconds the root device waits before changing states i e discarding to learning to forwarding This delay is required because every device should receive information about topology changes before it starts to forward frames In addition each port needs time to listen for conflicting information that would make it return to a discarding state otherwise temporary data loops might occur gt Topology Indicates if spanning tree topology is steady or undergoing reconfiguration The time required for recontiguration is extremely short so no values other that steady state are likely to be seen in this field gt Root ID The priority and MAC address of the device in the Spanning Tree that this switch has accepted as the root device and the port connected to the root device IGMP Status IGMP Status IGMP Status shows the IGMP Snooping statistics for the whole switch gt VLAN ID VLAN ID number gt Queri
10. IP is 192 168 2 1 gt Fallback Subnet Mask assign the subnet mask to the IP address gt Fallback Gateway assign the network gateway the default gateway is 0 0 0 0 gt Management VLAN ID of the configured VLAN 1 4094 to manage the switch By default all ports on the switch are members of VLAN 1 However if the management VLAN is changed the management station should be attached to a port belonging to this VLAN Wildix WSGO8POE User Manual 10 gt Name type in the new user name default value is admin gt Password type in the new password default value is admin gt SNMP Enabled enables or disables SNMP on the switch Supports SNMP version land 2c management clients gt SNMP Trap Destination IP address of the trap manager to receive notification messages from this switch Traps indicating status changes are issued by the switch to specified trap managers Specify trap managers so that key events are reported by this switch to your management station gt SNMP Read Community community string acts like a password and allows access to the SNMP database on this switch Authorized management stations are only able to retrieve MIB objects gt SNMP Trap Community community string sent with the notification operation Port Configuration Port configuration ensures access to a switch port based on MAC address limits the total number of devices using a switch port and protects against MAC flooding attacks P
11. User Manual 33 Contacts S Italy France 39 0461 1715112 33 176 747 980 support wildix com support wildix fr Wildix WSGO8POE User Manual 34
12. Value 0 normal v 1 low g 2 low X 3 normal v 4 medum 3 medium f 6 high v 7 high APPLY CANCEL Figure 1 11 3 Wildix WSGO8POE User Manual 21 QoS Configuration 9 Strict WRR Queue Mode Note WRR is not supported in Jumbo Frame mode QoS Mode 802 1p Prioritize Traffic Custom v 802 1p Configuration 802 1p 802 lp 802 1p Priority 802 1p Priority Value Priority Value Priority Value 7 Value lt 0 medium lt l low 2 low 3 normal 4 medium lt 5 uras 6 high 7 high medium APPLY CANCEL rogn Figure 1 11 4 QoS Mode DSCP DSCP Packets are prioritized using the DSCP Differentiated Services Code Point value The Differentiated Services Code Point DSCP is a six bit field that is contained within an IP TCP or UDP header The six bits allow the DSCP field to take any value in the range O 63 When QoS Mode is set to DSCP the DSCP Configuration table is displayed allowing you to map each of the DSCP values to a hardware output queue low normal medium or high The default settings map all DSCP values to the high priority egress queue You can use the Prioritize Trattic drop down list to quickly set the values in the DSCP Configuration table to a common priority queue Use Custom if you want to set each value individually When the QoS Mode is set to DSCP the DSCP Configuration table is displayed as shown below QoS Configuration Stict WRR Queue Mode Note WRR is not supported in Ju
13. WSGO8POE Switch User Manual Version 01 01 2011 VWildix nnn Introduction Product Overview Web Management Features Specifications Mechanical Performance Package Contents Hardware Description Physical Dimensions Weight Front Panel LED Indicators Rear Panel Hardware Installation Software Description Login Configuration Administrator Port Configuration VLAN Setting Trunking Link Aggregation Raid Spanning Tree IGMP Snooping Port Mirroring QoS Setting PoE Power over Ethernet Configuration Wildix WSGO8POE User Manual o o O o o N 0O OOF ODO OF uo a ua A Ba DA N u A N Ny mh ek O O O O A A M _ N N Q Storm Control Monitorning Statistic Overview Detailed Statics LACP Status RSTP Status IGMP Status VeriPHY Ping Maintenance Reboot Device Warm Restart Load Default Setting Factory Default Firmware Updating Software upload Backup Recovery Configuration File Transfer Logout Wildix WSGO8POE User Manual 24 25 25 25 25 26 28 28 30 32 32 32 33 33 33 Introduction Product Overview This switch is equipped with 8 ports PoE 10 100 1000BaseT X with 2 combo gigabit SFP open slots It is designed for easy installation and high performance in an environment where traffic is on the network and the number of users increases continuously The compact rigid 19 rack mount size is specifically designed for small to medium workgroups It
14. X Link Per Unit Power gt Power Consumption 130 Watts Max for 8 port share Max 30 per port gt Power Input 100 240V AC 50 60HZ gt Product Dimensions Weight 44 x 220 x 440 mm H x D x W 3 2kg Performance MAC Address 8K Buffer Memory 176 KB Jumbo Frames 9K Transmission Method Store and Forward Wildix WSGO8POE User Manual Package Contents Before you start to install this switch please verify your package that contains the following items gt One PoE Gigabit Ethernet Switch gt One AC Power Cord gt User Manual CD gt One Rack mount kit ce E is Hardware Description This part primarily presents hardware of the web smart switch physical dimensions and functional overview would be described Physical Dimensions Weight 44 x 220 x 440 mm H x W x D 3 2KG Front Panel The front Panel of the managed switch consists of 8 gigabit RJ 45 ports with 2 Combo gigabit SFP open slot The LED Indicators are also located on the front panel Wildix WSGO8POE User Manual 6 8 Pat Gaart Pot Enamat Switch wih 2 app SFP Open Slot LED Indicators The LED Indicators present real time information of systematic operation status This table provides description of LED status and the meaning Table 1 1 LED Indicators providing the power not providing the power 00000000 SFP Status o LIL Wildix WSGO8POE User Manual 7 Rear Panel The 3 pronged power plug is placed
15. able corresponds to one port or trunk trunked ports cannot be configured individually configure the trunk instead Wildix WSGO8POE User Manual 13 VLAN Per Port Configuration VLAN aware Ingress Filtering Port Enabled Enabled Packet Type Pvid Port 1 7 All TaggedOnly 12 Port 2 7 All Tagged Only Port 3 9 All Tagged Only p Port 4 All Tagged Only Pon 5 gt All Tagged Only w Pon 6 All Tagged Only Pon o All Tagged Only Port 8 All Tagged Only Apply Cancel Figure 1 5 3 Port Trunk The port number of the port or the ID of a trunk VALN Aware Enabled VLAN aware ports are able to use VLAN tagged frames to determine the destination VLAN of a frame Default Enabled VLAN aware ports strip the VLAN tag from received frames and insert the tag in transmitted frames except for the PVID VLAN unaware ports will not strip the tag from received frames or insert the tag in transmitted frames Ingress Filtering Enabled If enabled incoming frames for VLANs which do not include this ingress port in their member set are discarded Default Disabled Packet Type Sets the interface to accept all frame types including tagged or untagged frames or only tagged frames Default All If the Packet Type is set to All the port can accept incoming tagged and untagged packets Any received packets that are untagged are assigned to the default VLAN Any tagged packets are dropped unless the port is a member of
16. e layer3 IGMP packets sent in a multicast network When IGMP Snooping is enabled in a switch it analyzes all IGMP packets between hosts connected to the switch and multicast routers in the network When a switch hears an IGMP report from a host for a given multicast group the switch adds the host s port number to the multicast list for that group And when the switch hears an IGMP Leave it removes the host s port from the table entry It prevents flooding of IP multicast traffic and limits bandwidth intensive video traffic to only the subscribers IGMP Configuration gt IGMP Enabled When enabled the switch monitors network traffic to determine which hosts want to receive multicast traffic gt Router Ports Set if ports are connecting to the IGMP administrative routers gt Unregistered IPMC Flooding enabled Set the forwarding mode for unregistered not joined IP multicast traffic The traffic floods when enabled and forward to router ports when disabled Wildix WSGO8POE User Manual 18 gt IGMP Snooping Enabled When enabled the port monitors network traffic to determine which hosts want to receive the multicast traffic gt IGMP Querying Enabled When enabled the port can serve as Querier which is responsible for asking hosts if they want to receive multicast traffic IGMP Configuration IGMP Enabled J Router Ports ivi 24 30 407 50 60M 70 BY Unregistered IPMC Flooding enabled VLAN ID IGMP Snooping Enabled IGMP Queryi
17. er Show whether Querying is enabled gt Queries transmitted Show the number of transmitted Query packets gt Queries received Show the number of received Query packets gt vl Reports Show the number of received v1 Report packets gt v2 Reports Show the number of received v2 Report packets gt v3 Reports Show the number of received v2 Report packets gt v3 Leave Show the number of v3 leave packets received IGMP Status VLAN eat Queries Queries vi v2 v3 v2 ID transmitted received Reports Reports Reports Leaves 12 Active 1 0 0 0 0 0 Refresh Figure 2 5 VeriPHY VeriPHY Cable Diagnostics Wildix WSGO8POE User Manual 28 User can perform cable diagnostics for all ports or selected ports to diagnose any cable faults short open etc and feedback a distance to the fault gt Cable Diagnostics Cable diagnostics is performed on a per port basis Select the port number trom the drop down list gt Cable Status Shows the cable length operating conditions and isolates a variety of common faults that can occur on Category 5 twisted pair cabling Figure 2 6 1 VeriPHY Cable Diagnostics Wildix WSGO8POE User Manual 29 VeriPHY Cable Diagnostics Port Pon 5 lt Mode Anomaly wo X pair Apply Figure 2 6 3 VeriPHY Cable Diagnostics Port Poti Poti Mode Port 2 si Port 3 td Port 6 Port 7 Port 8 Figure 2 6 4 Ping This command sends ICMP echo request packets to another node on t
18. ghts with default values of 1 2 4 8 for queues O through 7 respectively This is the default selection Note WRR can only be selected if Jumbo Frame mode is disabled on the Port Configuration page QoS Configuration o Strict WRR Queue Mode Note WRR is not supported in Jumbo Frame mode QoS Mode QoS Disabled QoS Disabled 802 1p DSCP APPLY _ CANCEL Figure 1 11 1 Wildix WSGO8POE User Manual 20 QoS Mode QoS Disabled When the QoS Mode is set to QoS Disabled the following table is displayed QoS Configuration Strict WRR Queue Mode Note WRR is not supported in Jumbo Frame mode QoS Mode QoS Disabled v APPLY CANCEL Figure 1 11 2 QoS Mode 802 1p Packets are prioritized using the 802 1p field in the VLAN tag This field is three bits long representing the values O 7 When the QoS Mode is set to 802 1p the 802 1p Configuration table appears allowing you to map each of the eight 802 1p values to a local priority queue low normal medium or high The default settings are shown below When the QoS Mode is set to 802 1p the 802 1p Configuration table is displayed as shown below QoS Configuration Stict WRR Queue Mode Note WRR is not supported in Jumbo Frame mode QoS Mode 802 1p Prioritize Traffic Custom All Low Pnonty All Normal Priority All Mediurn Priority 802 1p Configu Hgh Pronty 802 1p 7 802 1p oh 802 1p apa 802 1p ae Value Y Value Y Vale 7
19. he network Ping Parameters gt Target IP Address IP address of the host gt Count Number of packets to send Range 1 20 gt Time Out setting the time period of host is Ping Use the ping command to see if another site on the network can be reached The following are some results of the ping command gt Normal response The normal response occurs in one to ten seconds depending on network traffic gt Destination does not respond If the host does not respond a timeout appears in ten seconds gt Destination unreachable The gateway for this destination indicates that the destination is unreachable Wildix WSGO8POE User Manual 30 gt Network or host unreachable The gateway found no corresponding entry in the route table Press lt Esc gt to stop pinging Ping Parameters Figure 2 7 1 192 168 0 1 Cot te Figure 2 7 2 Wildix WSGO8POE User Manual 3 Ping Parameters Target IP address 192 16801 Count E Time Out in secs 1 1 10 30 Ping Results Target IP address 192 168 0 1 tg lt n TCO Average Response Time in ms b Refresh Figure 2 7 3 Maintenance Reboot Device Warm Restart Press Yes button to restart the switch the reset is complete when the power lights stop blinking Warm Restart Are you sure you want to perform a Warm Restart No Figure 3 1 Load Default Setting Factory Default Forces the switch to restore the original factory se
20. mbo Frame mode QoS Mode OscP Prioritize Traffic 48 High Priory Custom All Low Pronty All Normal Pronty All Medium Pronty OSCP Configu L DSCP Value 0 63 Priority Figure 1 11 5 Wildix WSGO8POE User Manual 22 DSCP Configuration DSCP Value 0_ 63 Priority high 7 low normal medu nigr high k high high k high All others high v APPLY CANCEL Figure 1 11 6 PoE Power over Ethernet Configuration Power over Ethernet PoE is an advanced technology PoE devices products deliver power to wide range of devices this technology is especially useful for VoIP phones wireless LAN access points and IP cameras It is deployed when AC power is inconvenient expensive or infeasible to supply Web Smart features are able to realize remote control and centralized power management CATS cable deliver data and power PoE Configuration Remote access and monitor the attached PD Powered Device status Enable Disable PoE Enabled PoE of the port is able to supply power to the attached PD Delivering Power W Output power Current mA Current status of port PoE Power over Ethernet Configuration Power Budget r PD Class sanje Current mA Voltage V fo EE 9 249 HTH A 9 THH HTH BE O ee TORT T THT ETT S TEE TTT NIT RTT THIS EE HL 790 E a a E S HHR a TORO RTS THH TER TRE TE T HT RET E T T HII ee PT HT ee ROTH oe an i an ee nT TT Figure 1 12 1 Wildix WSGO8POE User Manual 23 Storm Control Broadca
21. ng Enabled 1 d d Apply Refresh Figure 1 9 1 Port Mirroring Port Mirroring is used on a network switch to send a copy of network packets seen on one switch port or an entire VLAN to a network monitoring connection on another switch port This is commonly used for network appliances that require monitoring of network traffic such as an intrusion detection system Mirroring Configuration gt Port to Mirror to The port that duplicates or mirrors the traffic on the source port Only incoming packets can be mirrored Packets are dropped when the available egress bandwidth is less than ingress bandwidth gt Ports to Mirror Select the ports that you want to mirror from this section of the page A port is mirrored when the Mirroring Enabled check box is checked Mirroring Configuration Mirror Source S O dW Oe U Na Mirror Port 1 Apply Refresh Figure 1 10 1 Wildix WSGO8POE User Manual 19 Mirroring Configuration Mirror Source eon A AAO N Mirror Port Apply Refresh NM h j GB d Z LP i Figure 1 10 2 QoS Setting In QoS Mode select QoS Disabled 802 1p or DSCP to configure the related parameters QoS Configuration gt Strict Services the egress queues in sequential order transmitting all traffic in the higher priority queues before servicing lower priority queues gt WRR Weighted Round Robin shares bandwidth at the egress ports by using scheduling wei
22. ort Configuration In Port Configuration you can set and view the operation mode for each port gt Enable Jumbo Frames This switch provides more efficient throughput for large sequential data transfers by supporting jumbo frames on Gigabit Ethernet ports up to 9 6 KB Compared to standard Ethernet frames that run only up to 1 5 KB using jumbo frames significantly reduces the per packet overhead required to process protocol encapsulation fields gt Power Saving Mode Adjusts the power provided to ports based on the length of the cable used to connect to other devices Only sufficient power is used to maintain connection requirements gt Mode allow user to manually set the port speed as Auto 10 half 10 Full 100 Half 100 Full 1000 Full or Disabled Press Apply button to complete the configuration procedure Wildix WSGO8POE User Manual 1 Port Configuration Enable Jumbo Frames PERFECT_REACH Power Saving Mode Full lt Full Link down Disable Link Mode Flow Control Auto Speed Auto Speed Auto Speed Auto Speed Auto Speed Auto Speed Auto Speed sn M w Ww N k Auto Speed Figure 1 4 1 Port Link Mode Flow Control Auto Speed v Auto Speed 10 Half 10 Full 100 Full 1000 Full Disabled Auto Speed Auto Speed lt O N fF A A Mad NH k Auto Speed Drop frames after excessive collisions Refresh Figure 1 4 2 VLAN Setting A Virtual LAN VLAN is a logical ne
23. st storms may occur when a device on your network is malfunctioning or if application programs are not well designed or properly configured If there is too much broadcast traffic on your network performance can be severely degraded or everything can come to complete halt You can protect your network from broadcast storms by setting a threshold for broadcast traffic for each port Any broadcast packets exceeding the specitied threshold is then dropped Storm Control Configuration There are three types of traffic which can be rate limited including broadcast multicast frame and Flooded Uncast Rate Storm Control Configuration Storm Control Number of frames per second Broadcast Rate No Limit lt Multicast Rate No Limit lt Flooded unicast Rate No Lima lt Figure 1 13 1 gt Enable Rate Limit Click the check box to enable storm control gt Rate number of frames per second The Rate field is set by a single drop down list The same threshold is applied to every port on the switch When the threshold is exceeded packets are dropped irrespective of the flow control settings gt Web Click PORTS Storm Control This page enables you to set the broadcast storm control parameters for every port on the switch Storm Control Configuration Storm Control Number of frames per second Broadcast Rate 9910 t 1982 Multicast Rate 3964 Flooded unicast Rate v 9910 Apply Refresh 11892 13874 15856 17838 No Limit Figure
24. ttings To reset the switch select Reset to Factory Defaults from the drop down list and click Apply The LAN IP Address Subnet Mask and Gateway IP Address are reset to their factory defaults Wildix WSGO8POE User Manual 32 Firmware Updating Software upload Select Upgrade Firmware from the Tools drop down list then click on the Browse button to select the firmware file Click the APPLY button to upgrade the selected switch firmware file You can download firmware files from the Support section of your local supplier Software Upload ae Upload Figure 3 2 Backup Recovery Configuration File Transfer Configuration file transfer allows you to save the switch s current configuration or restore a previously saved configuration back to the device Configuration files can be saved to any location on the web management station Select Upload the configuration file to save a configuration or Download to restore a configuration Use the Browse button to choose a file location on the web management station or to find a saved configuration file Configuration Upload aa Upload Configuration Download Download Figure 3 4 Logout The administrator has write access for all parameters governing the onboard agent User should therefore assign a new administrator password as soon as possible and store it in a safe place Please enter password to login Password Apply Figure 3 5 Wildix WSGO8POE
25. twork grouping that limits the broadcast domain which would allow you to isolate network traffic so only the members of the same VLAN will receive traffic from the ones of the same VLAN Basically creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch However all the network devices are still plugged into the same switch physically Port Segmentation VLAN Configuration gt VLAN ID ID of configured VLAN 1 4094 no leading zeroes gt VLAN Configuration List Lists all the current VLAN groups created for this system Up to 16 VLAN groups can be defined VLAN 1 is the default untagged VLAN Wildix WSGO8POE User Manual 12 Port Segmentation VLAN Configuration Add a VLAN VLAN ID 17 VLAN Configuration List 12 9 Mody Delete Refresh Port Config Figure 1 5 1 VLAN Setup The switch supports up to 16 VLANs based on 802 1Q standard From the VLAN Membership page you can create and delete VLANs and change the VLAN port membership VLAN Setup VLAN ID 12 Port Member Port Member Port 1 d Port 5 Boat 2 Vv Port 6 Port 3 Port 7 J Port 4 Pot8 v Refresh Figure 1 5 2 VLAN Per Port Configuration The 802 1Q Per Port Configuration page allows you to change the VLAN parameters for individual ports or trunks You can configure VLAN behavior for specific interfaces including the accepted frame types and default VLAN identifier PVID Each row of the t
Download Pdf Manuals
Related Search