uk-300t user`s manual
Contents
1. 1 4 1 52. UK 300T USER S MANUAL Functions 2Band EQ with Chromatic LED tuner 1 Tuner LED Display Tuner LED Display ABCDEFG chromatic Tunep gt Tuning Guide LED for Sharp tune gt YS Tuning Guide LED for right tune ABCDEFG a Tuning Guide LED for flat tune 2 Bass for bass tones 3 Treble for high tones The BASS TREBLE controls are a 3 band equalizer for controlling tone LB BASS TREB UK 300T The center detent on these tone controls yields a flat tone response 12 boosts the tone 12 cuts the tone 4 Volume Knob The VOLUME controls the output volume At O it is completely OFF At 10 it is loud le o e Oe o eo 5 Low Batt Low Battery LED Light The LED will light when the battery has lost power Replace the 1 Tuner LED Display battery when this light is on 2 Bass This LED light will flash when a cable is connected to the output 3 Treble jack of the pickup system This shows the battery is good 4 Volume Knob 5 Low Batt Low Battery LED Light 6 Tuner on off Button 6 Tuner on off Button Power switch of built in Chromatic LED tuner 7 Battery box Automatic power off after 5 minutes 7 Battery box 2 X CR2032 Coin Battery 1 CENNE oe Specification Caution The jack should be pluged for proper Preamp working Features 2Band EQ with Chromatic LED tuner TUNER will works regardless pluging jack Input Impedance 22 MQ There i
3. s no output sound please check if tuner or mute is turned on Frequency Response 20Hz 20KHz When LCD screen is dim or no display please check battery life Control Range To prevent battery loss please unplug jack when preamp is not in use Do not disassemble for repair Bass 12dB at 100Hz Return to your dealer for service or repair Treble 12dB at 10KHz Do not use too much force when operating the control Battery Status LED Power Supply 2 X CR2032 Coin Battery Battery Life Only Eq Over 200Hours Tuner on Over 100Hours Pick up Omega II Piezo Cable pick up Dimension W 56mm X H 40mm 2 2 X 1 6 belat BELCAT Co Ltd Tel 86 752 355 7545 ROHS Fax 86 752 355 2460 Email belcat belcat com This product complies with the RoHS directive Internet www belcat com INSTALLATION 1 Contents Hk 1 Preamp 4 Clip 2 Tool 1 Electric Drill ESS 2 Drill Bit 2 3mm or 3mm and 12mm 3 Phillips Screwdriver mm 2 Output Jack MANUAL 3 Pick Up 5 Screw 4 Router and Grinder cutting edge 3mm om ee 5 Round File gt 6 Masking Tape 1 Cut out the hole with template Cutting Masking Template Masking 4 Fasten screws properly 6 Installing the pick up 3 Insert EQ and battery box into hole of guitar 5 Put plugs into jacks 7 Fix wire with clip Out put jack X Cable Sol
4. ution 1 When there is no sound or sound is stopped Check guitar cable amp or Mixer Check if there is batter or not When it happens noise or distortion please exchange battery Check if the pickup and battery connector is connected correctly or not Check if out put jack is connected correctly 2 When there is hum noise Check the pickup is connected well or not Check if the connectors are connected to correct position well or not 3 Some causes of the balance problem When the bottom of saddle or the groove of saddle is not flat When saddle is installed to the groove of saddle loosly When the connection is not good between the bottom of saddle and the groove of saddle When Saddle is very short When there is grounds on the groove of saddle When Saddle is declined toward front or back When the top of guitar is bended When the pickup is installed to only a part of the groove of saddle back page Cutting Template 1 Print gt Page Handling gt Page Scaling W None O Fit to print margins Reduce to print margins 2 2 Check the size with actual ruler 5 Cut follow solid line use cutter 50 9mm O O Se eae eames Preamp Opening 3 4 5 6 7 8 9 1 12 1 10 1 3 1 Print this file without scaling option 3 Cut out the dotted line or desire model 4 Adhere to location use double stick tape
Download Pdf Manuals
Related Search