16CH Digital Video Recorder User`s Manual
Contents
1. Use UP 1 DOWN 3 button for up and down movement of PTZ camera LEFT 4 RIGHT 2 for left and right movement and FF gt REW 4 4 buttons for zoom IN and OUT d To escape PTZ control mode press ENTER button or any button Then the PTZ MODE OSD on upper right corner of monitor will be disappeared NOTE Before using PTZ control mode please check that correct selection of PTZ protocol in PTZ TYPE of DISPLAY SETUP is done IV Software Upgrade Procedure 1 S W Upgrade procedure 1 Copy files including hqd1600 tar into USB Memory Drive using PC in advance 2 3 4 5 6 7 Turn off power of your DVR Turn on power of your DVR Insert USB Memory Drive into USB port in front panel of DVR Press MENU button Input password and then press ENTER button Select SYSTEM SETUP menu in main menu It takes several seconds for your DVR to display SYSTEM SETUP menu because 7 upgrade files like hqd1600 tar has been read into your DVR SYSTEM SETUP LANGUAGE ENG CHN VIDEO FORMAT NTSC PASSWORD eek ADMIN LOCK YES TIME FORMAT 24HOURS DATE FORMAT MM DD YY DATE TIME SET 05 20 2005 10 50 11 DEFAULT YES NO REV STATUS VERSION 1 1 1 ENTER AV 4 EXIT NOTE The terminology of 9 REV STATUS of SYSTEM SETUP in version 0 0 3 current version is changed into 9 REV STATUS in version 0 0 4 new version After finishing S W upgrade terminology will be chan2. VIDEO LOSS 14 PLAYBACK Mode Normal playback can be started PLAY button gt after recorded file selection in search list While your DVR is in playback mode the camera channel which want to watch could be selected by UP RIGHT DOWN LEFT button Fast forward FF or fast backward playback REW 4 4 can be done by FF gt gt REW 4 4 button In order to freeze picture in playback PAUSE IM button is used The movement of single field in still picture mode can be fulfilled by PAUSE button For selecting the forward or backward playback of single field FF gt gt REW 4 4 button would be needed to press before using PAUSE button Your DVR supports x2 x4 x8 x16 x32 playback for Fast Forward x2 x4 x8 x16 play back for Fast Backward Note When motion in image is detected or external alarm is triggered there is pop up image display of the channel during 30 seconds But your DVR doesn t display pop up image display of the channel when your DVR is in playback mode or search list Menu to minimize user s inconvenience Ci SY Lm A 12 03 2004 06 26 23 PM Playback Mode u Ex v i pus z IT LL V2 m em 15 PTZ Control Procedure a Select the camera which PTZ camera is connected to control PTZ using UP A RIGHT gt DOWN Y LEFT 4 buttons of front panel in your DVR b Press ENTER button to select PTZ mode PTZ MODE OSD will be displayed on upper right corner of monitor
3. DURATION WEEK START 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 10 Ui gt HDD INFORMATION mem HARDDISK TOTAL ARCHIVING TYPE FREE ARCHIVING TIME 2 FORMAT HDD ARCHIVE INFO 3 OVERWRITE TOTAL ARCHIVE LOG HOLIDAY Main Menu Programming 1 Overview Main Menu Before using your DVR for the first time you will want to establish the initial settings This includes items such as time and date password display record mode network and so on In order to program Main Menu first press MENU button of front panel in DVR If ADMIN LOCK is set as YES factory default is YES below figure will be appeared PASSWORD LOGIN Then input password number using 1 2 3 4 Channel Buttons Factory default is to PASSWORD press 1 button 4 times and press ENTER button MAIN MENU will be appeared ENTER AV 4 b EXIT NOTE To access the DVR Main Menu press MENU To escape MENU ESC button is also used Buttons for movement in Menu are lt or gt Button for selection is ENTER Buttons for increasing or decreasing parameter are A or Press ESC to return to the previous MENU after setting and to save the values of setup Ji lt LEFT RIGHT Y DOWN and ENTER buttons e MAIN MENU gt MAIN MENU SYSTEM SETUP DISPLAY SETUP RECORDING SETUP ALARM SETUP MOTION SETUP WEEKLY SCHE
4. l Introduction Package Content When purchasing this product unpack it at first and unload it on a flat floor or a place where it is to be located Then verify that the following contents are contained 16CH DVR Adapter 12V 5A Rack Mount Bracket User s manual Remote controller Optional Install CD 8CH BNC cable harness for loop through video output 2EA Optional en ne ee E ee ee ee 9 1 16CH DVR Adapter Rack Mount Bracket User s Manual Install CD Remote controller BNC cable harness Optional for loop Optional 2 Features This DVR provides recording capabilities for 16 camera inputs It provides playback or live display and network function while in recording mode And also it offers the following features 16 Composite Input Connectors 16 Loop Through Video Connectors Compatible with Color NTSC or PAL and B amp W CCIR and EIA 170 Video Display and Record Video Resolution Display Resolution NTSC 720x240 PAL 720x288 real time display Display mode Full QUAD 8 9 10 16 picture display mode and Sequential Image Display Compression M JPEG Standard image high quality 16KB field Multiple Search Categories Date Time Event Manual Schedule Records up to 60 NTSC IPS 50 PAL Images per Second Normal Recording 16CH multiplexing recording with 720x240 NTSC 720x288 PAL at field mode Alarm Motion recording 1CH recor
5. Purchasing Date Warranty Period 1 year from the purchasing date The product Warranty Sheet will not be issued again The Product Warranty Sheet must be filled on the same day of the product s purchase It will be requested to show this warranty to receive free repair service
6. 4x4 16 picture will be displayed on monitor Whenever it is pressed two 8 1 7 picture with CH1 CH8 and CH9 CH16 and two 10 2 8 picture with CH1 CH10 and CH7 CH16 will be displayed on monitor repeatedly If changing main picture bigger picture is requested in 8 1 7 picture mode and 10 2 8 picture mode it can be done by pressing channel selection button just after pressing FUNCTION button lt 16 picture Display gt lt 8 Ru SIUS gt lt 10 picture Display gt E Sequential Picture Display Mode All of video channels connected with video inputs of DVR are sequentially displayed on monitor 13 RECORDING Mode There are several kinds of recording modes such as Manual Schedule Alarm event Motion Recording quality including high standard plus standard low for all of recording is decided by the QUALITY setting in RECORDING SETUP Menu Frame rate recording time can be separately selected in each of RECORDING SETUP Menu It is recorded on HDD that 16CH video input signals are multiplexed with field by field 1 Manual recording is started by REC STOP button of front panel 2 WEEKLY RECORDING can be started by setting in WEEKLY SETUP 3 Motion Recording can be started when any motions in image are detected 4 Alarm recording is started by external alarm trigger input en Recording Mode N A de 03 2004 06 26 23 coi 269 VA 1 m 5 N a TONG x mm H Lt S LELT
7. by Left or Right button Search list sorting support All Event Schedule and Time Network GUI or Internet Protocol TCP IP PPP and DHCP Explorer GUI or Internet Explorer viewing and configuration support APPENDIX 1 Specification 1 2 HDD Management One or Two EIDE ATA 6 3 5 inch 7200rpm Archiving USB Storage Class Key for data backup Firmware upgrade System log file Pan Tilt Zoom RS485 Controlled by button Viewer S W Mechanical Unit dimension 44 W x31 5 D x4 4 H 17 3 in x12 4In x 1 73 In 19 rack mountable 1U Unit Weight 1110 5kg Ambient Temperature 40 to 104 F 5 to 40 Approval FCC Class A CE and MIC APPENDIX 2 Pin Description of connectors 1 USB Pin Descriptions Pin description 3 omg 3 ome 5 3 85485 Pin Descriptions D LAN port RJ 45 Pin Descriptions s mo s No connected VR Slave Unit like PTZ Camera 4 Alarm Input amp Outputs Pin Descriptions 0000000 mongmunummnunuumum YE ot lt Alarm Input Pin gt lt Alarm Output Pin gt Ground Common Ground Common Ground e Sermo Ground Common 8 Semwmut 9 Sensorinputo7 Ground Common 12 Ground Common 7 16 Sensor input 14 17 Sensor input 15 18 Sensor input 16 19 Ground Common Ground Common 0 o 12 EN LO y 6 EE RN EN 09 War
8. camera from remote area by network viewer software proper PTZ TYPE should be selected in here Your DVR supports over ten PTZ cameras According to customer requirements PTZ control will be added in it NOTE PTZ stands for pan tilt and zooming PTZ protocols Panasonic Pelco D PelcoP Techwin Niko DRX502A_DSC230s KRE 301 302 GC 755 NP TOA CC554 RAS716LS and so on 2 SEQ DEWLL TIME 1 to 60 seconds SEQ DWELL TIME can be changed using LEFT or RIGHT button NOTE It is just reflected in sequential display mode 3 SPOT DWELL 1 to 60 seconds SPOT DWELL TIME can be changed using LEFT or RIGHT button All of video channels connected with video inputs of DVR are sequentially switched for video output for SPOT monitoring 4 TIME DATE OSD ON OFF When it is set as OFF characters which indicates time date will be disappeared on monitor But time and date information still are added into recording files 5 CAM NUMBER OSD ON OFF When it is set as OFF characters which indicates camera number will be disappeared on monitor 6 VIDEO LOSS OSD ON OFF When it is set as OFF black pictures will be displayed in the cameo with video loss When it is set as ON VIDEO LOSS character with white color will be displayed in blue screen 7 POP UP DISPLAY ON OFF When it is set as OFF pop up image of camera which motion detection or alarm triggering is occurred will not displayed When it is set as ON the cha
9. hold the button and insert the wire in the hole below of connector pin After releasing the pin pull gently on the wire to make certain it is connected To disconnect a wire press and hold the connector pin above the wire and pull out the wire 16 Alarm Inputs 1 2 3 4 16 G Ground You can use external devices to signal the DVR responding to events Mechanical or electrical switches can be wired to the Alarm Inputs and GND Ground connectors The threshold voltage is 4 3V and should be stable at least 0 5 seconds to be detected G Ground COM common G is same as common Connect the ground side of the Alarm input to G Ground Connect the ground side of relay output to COM connector 4 Relay output 4 relay output with NO or NC can be sent to external device You can select NO or NC according to characteristic of mechanical or electrical switch 7 Ethernet Port RJ45 jack Connect a Cat5 cable with an RJ 45 jack to the DVR connector Remote PC viewer software via network enable you to live viewing or searching 8 RS232C serial port An RS232 port is provided to connect other external equipments Use DB 9S female connector to connect to the DVR 9 Power Input from Adapter Connect the adaptor to the DVR for DC power supply DC 12V 5A Remote Controller lt Remote Controller buttons gt Stand alone Digital Video Recorder P Button
10. 16CH Digital Video Recorder User s Manual This user s manual is subject to change without any previous notice by Version_1 0 function upgrade or addition May 2005 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This label may appear on the rear of the unit due to space limitations The lightning flash with arrow point symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of importance operating and maintenance servicing instructions in the literature accompanying the appliance Warning To reduce the risk of fire or electric shock Do not expose this product to rain or moisture Do not insert any metallic object through ventilation grills Power disconnect Units with or without ON OFF switches have power supplied to the unit whenever the power cord is inserted into the main source However the unit is operational only when the ON OFF switch is in the ON position To disconnect it from the main source you have to disconnect the Power cord FCC COMPLIAN
11. 26 063 001 PORT 5000 NTP TIME OFF ON TIME ZONE GMT 08 00 DDNS STATUS NONE OK ERR 1 2 3 4 5 6 7 8 9 A V 4 gt EXIT To access NETWORK SETUP press ENTER when NETWORK SETUP in MAIN MENU using DOWN or UP is highlighted with blue color The menu above will appear on monitor 1 CONNECT STATIC or DHCP You DVR can select STATIC IP or DHCP using LEFT or RIGHT Button 2 IP ADDRESS 3 SUB NET MASK 4 GATE WAY If static IP be selected IP address SUB NET and GATEWAY should be written on it manually according to network environment LEFT or RIGHT button is used for movement DOWN or UP button is used for changing the value of parameter If DHCP be selected your DVR would read network parameters automatically from network equipment display them on IP ADD SUB NET and GATEWAY 5 DNS DNS Server IP setting to change Domain Name into IP address Default value is KT s Domain Name Server IP 6 PORT Port number for TCP IP connection in DVR Net Viewer should have same port Number to access remote DVR through network 80 TCP www http World Wide Web HTTP Ex 123 UDP NTP Network Time Protocol Default Port No is 5000 If Port is set as 5000 port number of from 5000 to 5002 is used in DVR Therefore If DVR is used in network environment with firewall port number of from 5000 to 5002 should be opened for DVR s external access If IP sharing machine is used with DVR port forwarding should be don
12. 3 4 5 6 7 8 9 10 20 30 40 50 60 minutes It can be selected using LEFT or RIGHT button 3 SENSOR TYPE NONE N O N C Your DVR can select the input type for external alarm inputs which usually has normal open or normal close using LEFT or RIGHT button 4 ALARM INPUT Relay TRIGGER Out Your DVR support both dry open and dry contact through relay output port 1 to port 4 It can be selected using LEFT or RIGHT button Trigger Output 1 to 4 corresponding to alarm input from 01 to 16 can separately be designated For example trigger output for alarm input 01 can be designated as DISABLE when trigger output isn t needed Trigger output for alarm input 02 can be designated as trigger output 1 Trigger output for alarm input 10 can be designated as trigger output 3 Trigger output for alarm input 16 can be designated as trigger output 4 5 BUZZER ALERT DISABLE ENABLE If external alarm sensor s be triggered beep sound from buzzer by BUZZER ALERT with ENABLE would be occurred during two seconds 6 MOTION SETUP 5 MOTION SETUP SENSITIVITY Normal FRAME RATE 60 IPS DURATION 1 MIN CAM NUM CH1 CH16 AREA SETTING DISABLE ALL SETUP TRIGGER OUT DISABLE 1 to 4 BUZZER ALERT DISABLE ENTER A AN EXIT Your DVR has built in video motion detection function Motion detection Enable Disable motion area can be selected separately for each camera When your DVR detects motion it begin to record mult
13. CE STATEMENT A CLASS A computing device subject to certification by the Commission shall be identified pursuant to Par 2 925 et Seq of the chapter In addition the label shall include the following statement This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Where a device is constructed in two or more sections connected by wires and marked together the statement specified in this Section is required to be affixed only to the main control unit The users manual or instruction manual for the EUT shall contain the following statement or equivalent Caution Changes or Modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment If the EUT requires accessories such as special shield cables and or connectors to enable compliance with emission limits the instruction manual for the EUT shall include appropriate instruction on the first page of the text concerned with the installation of the device that these special accessories must be used with the device It is the responsibility of the user to use the needed special accessories supplied with the equipment For a CLASS A digital device or peripheral the instruction furnished the user shall include the f
14. CK button can be utilized If this button is pressed all of buttons in front panel are not operated with yellow LOCK LED To release buttons LOCK password will be requested just after pressing LOCK button If correct password is input button LOCK will be released 6 Archiving button Whenever ARCHIVE button is pressed archiving will be started 7 REC STOP button Press REC Red circle to begin record Press REC to stop recording again This is toggle button 8 REW 4 4 Press REW perform high speed backward playback It support 2 16 times playback speed 9 PLAY button gt 10 STOP button If PLAY gt is pressed search lists will be displayed on monitor After selecting one recorded file among lists playback will be started by PLAY button To stop playback STOP button is used While DVR is in high speed playback mode like FF or REW it return to playback by PLAY button 11 FF gt Press FF to perform high speed forward playback It support 2 to 32 times playback speed 12 PAUSE IH Press PAUSE to pause playback This PAUSE button can be used for backward or forward movement by one field The direction of field movement is decided by pressing FF or REW previously 13 MENU Press MENU button to enter menu system 14 ESC ESC button is used to return upper menu and to save set up parameter at the same time 15 Direction button and Enter Button Direction buttons are used to move LEFT RIG
15. DULE NETWORK SETUP ARCHIVING HDD INFORMATION A V EXIT 2 SYSTEM SETUP To access SYSTEM SETUP press ENTER button after moving highlight bar to SYSTEM SETUP in MAIN MENU Below menu will appear on monitor SYSTEM SETUP LANGUAGE ENG CHN VIDEO FORMAT NTSC PASSWORD ADMIN LOCK YES TIME FORMAT 24HOURS DATE FORMAT MM DD YY DATE TIME SET 05 20 2005 10 50 11 DEFAULT YES NO REV STATUS VERSION AV 4 EXIT 1 LANG Language Selection The languages supported are English Chinese Japanese 2 VIDEO FORMAT NTSC PAL Video format is automatically detected after power ON The detected video information will be displayed on VIDEO FORMAT User don t need to change video format 3 PASSWORD Move Highlight bar to PASSWORD in the SYSTEM Menu using DOWN or UP button And then press ENTER to change password For four digit password input 1 2 3 and 4 buttons can be used NOTE Factory Default is Pressing 1 channel button four times SYSTEM SETUP PASSWORD Input old password Factory Default is Pressing 1 button four times SYSTEM SETUP PASSWORD Input new password Enter the password by pressing the appropriate combination of four SYSTEM SETUP number 1 2 3 4 buttons PASSWORD Input new password again to confirm new password 4 ADMIN LOCK YES NO Move Highlight bar to ADMIN LOCK in th
16. Description gt Ro beserpion Buron ame 1 Sequential display button Video Picture 2 QUAD display button Display mode 3 9 picture display button 4 16 8 10 picture display button Main picture selection button Function in 8 10 picture display mode Movement to upper menu Movement to menu mode MENU 1 UP A Direction 2 DOWN Password 3 LEFT 4 Number Input and 4 RIGHT gt 5 ENTER ENTER buttons Playback Stop button STOP Playback Start button Search PLAY PAUSE 1 field movement Movement backward forward or PAUSE 1 field movement backward forward by 1 Field Fast Playback buttons FF REW Menu Tree MAIN MENU DISPLAY SETUP RECORDING SETUP ALARM SETUP MOTION SETUP WEEKLY SCHEDULE NETWORK SETUP SYSTEM SETUP i Ui 5 VIDEO FORMAT PASSWORD ADMIN LOCK TIME FORMAT DATE FORMAT DATE TIME SET DEFAULT REV STATUS DISPLAY SETUP BRIGHTNESS CONTRAST PTZ TYPE SEQ DWELL TIME SPOT DWELL TIME DATE OSD CAM NUMBER OSD VIDEO LOSS OSD POP UP DISPLAY POSITION ARCHIVING HDD INFORMATION MOTION SETUP e AUDIO STOP KEY FRAME RATE CAMERA NUM DURATION RECORD AREA SETTING TRIGGER OUT BUZZER ALERT ALARM SETUP DURATION SENSOR TYPE ALARM INPUT TRIGGER OUT BUZZER ALERT NETWORK SETUP IP ADD SUB NET GATE WAY DNS PORT NTP TIME TIME ZONE DDNS STATUS WEEKLY SCHEDULE
17. EKLY SCHEDULE MAIN MENU using DOWN or UP button is highlighted with blue color The menu above will appear on monitor WEEKLY SCHEDULE START DURATION 00 00 00 00 00 00 00 00 NONE NONE ENTER A V EXIT When blue bar is on SUN blue bar movement from SUN to SAT and HOLIDAY can be selected by DOWN or UP button To return Main Menu ESC button is used To move START DURATION and OFF ON LEFT or RIGHT Button is used To decide the time for START time DURATION and OFF ON time with bold character or OFF ON at that position can be changed by DOWN or UP button For example the blue bar movement by LEFT or RIGHT Button like this WEEKLY SCHEDULE WEEKLY SCHEDULE START DURATION START DURATION SUN 00 00 00 00 00 00 00 00 WEEKLY SCHEDULE WEEKLY SCHEDULE START DURATION START DURATION SUN 00 00 00 00 SUN 00 00 00 00 WEEKLY SCHEDULE START DURATION SUN 00 00 00 00 When blue bar is placed on START DURATION and OFF ON you can change value like time or ON OFF When there is no bold character blue bar can move from SUN to SAT and HOLIDAY START means recording starting time It can be changed from 00 00 to 23 59 DURATION means total recording time duration HOLIDAY is for holiday recording setup It can be adjusted from SUN to SAT 8 NETWORK SETUP 7 NETWORK SETUP STATIC DHCP IP ADD 192 168 123 171 SUB NET 255 255 255 000 GATE WAY 192 168 123 254 DNS 168 1
18. HT UP and DOWN in menu They also can be used to input password ENTER button is used to save parameter to select parameter in the menu And also in playback it is used to select one of listed file for playback after searching recorded files by all time alarm motion manual and so on 16 LED Indicators POWER NETWORK REMOCON USB Archiving EXT REC Lock 1 POWER LED This red LED turns ON when Power is ON 2 NETWORK indication LED This green LED will turn while data communication is working through network 3 Archiving LED This green LED will turn ON while data archiving is working through USB Memory driver 4 REC This red LED will turn ON during recording 5 EXT This yellow LED will turn ON when external alarms are triggered or motions are detected 6 LOCK This yellow LED will turn ON while LOCK button is working 7 Remote Controller receiver Remote controller sensor input window 1 gt 16CH Video Input 16 channel composite video inputs with BNC connectors Since this DVR automatically detects video format NTSC or PAL as soon as power is ON NTSC or PAL video sources can be connected in DVR But NTSC and PAL video sources for 16CH video inputs can not be mixed If they are mixed DVR can not be operated properly 2CH Video Output One video output Upper BNC is used to monitor live playback pictures Th
19. RS MM DD YY 05 20 2005 10 50 11 HOUR SET 09 HOUR REV STATUS WAIT 1 1 1 9 1 1 2 ENTER A V 40 EXIT 11 S W Upgrade Completion S W upgrade version will be seen on 9 REV STATUS of SYSTEM SETUP SYSTEM SETUP LANGUAGE VIDEO FORMAT PASSWORD ADMIN LOCK TIME FORMAT DATE FORMAT DATE TIME SET 05 20 2005 GMT HOUR SET REV STATUS ENG CHN NTSC EEEk YES 24HOURS MM DD YY 10 50 11 09 HOUR VERSION Upgrade Version 1 1 2 V EXIT APPENDIX 1 Specification 1 2 Compression Rate KB image Normal image 13 17KB Image NTSC 15 19KB Image PAL NTSC 720x240 PAL 720x288 Complex image 20 25KB Image NTSC 22 27KB Image PAL o Frame Rate Recording IPS 16CH video real time multiplexing recording Total number of Images sec 60 IPS 720x240 NTSC 50 IPS 720x288 PAL Recoding Mode Images sec 60 30 15 10 5 1 0 5 NTSC 50 25 12 6 5 1 0 5 PAL Manual Schedule Motion Event 5 Permits those allowed to access the system Status Indicator LED Power Network Archive Record EXT Key Lock Alarm Event Motion Selectable recording CH Pop up Display Duration 30sec 1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 min Alarm In 4 Relay Out 1 NONE NO or NC selectable Both NO and NC support in rear panel for Relay Out Playback Normal x1 speed Fast Forward x2 x4 x8 NTSC PAL Fast Backward x2 x4 x8 NTSC PAL Move 1 page movement
20. TE 1 If PLAY button be pressed two times successively latest recorded file could be playbacked soon 2 The example for searching recorded files by TIME Search list by TIME can be selected from ALL TIME MANUAL ALARM MOTION SCHEDULE using DOWN or UP button After moving 11 20 2004 date area using LEFT or RIGHT Button and then related date character would be turned into bold character the date which want to search can be selected by using DOWN or UP button Then recorded files just after selected date time ex 11 20 2004 10 33 would be listed as bellows To playback a recorded file from listed files press ENTER button to move listed files And then press PLAY button gt for playback after selecting the recorded file using DOWN or UP button SEARCH LIST LIST 11 20 2004 10 33 1 11 20 2004 10 33 11 20 2004 11 20 2 11 20 2004 22 00 11 20 2004 23 10 12 DISPLAY Mode There are three kind of display modes such as single as full QUAD sequential mode regardless recording mode When there are motion detection or alarm triggering the video channel which motion is detected or alarm is triggered would be display on monitor during 30 Seconds After it pass 30 Seconds your DVR would display previous display mode such as full QUAD or sequential picture 12 03 2004 06 26 23 PM NAT SEY 7 Ao a gt m RJ NEU 4713 AM MAIN MENU on SYS
21. TEM SETUP EN DISPLAY SETUP BaN RECORDING SETUP SLEDS ALARM SETUP MOTION SETUP WEEKLY SCHEDULE NETWORK SETUP ARCHIVING 1 2 3 4 5 6 7 8 9 HDD INFORMATION When your DVR is in recording playback and network mode gt are displayed on left top corner of monitor But it is on MENU Mode P are temporarily disappeared as upper figure 12 1 Picture Display Mode A Full Picture If each video channel selection is pressed the channel will be displayed as full screen The video channel from CH11 to CH16 in remote controller can be selected with 10 digit button and 1 4 digit button together Ex For selecting CH15 press 10 digit 10 and then press No 5 for 1 digit number If QUAD picture button is pressed first time QUAD picture a4 with CH1 to will be displayed on monitor Whenever it is pressed QUAD picture displayed on monitor will be changed 4 from CH1 CH4 CH5 CH8 CH9 CH12 to CH13 CH16 on and on The QUAD picture mode for monitoring can be selected by pressing this button repeatedly If 9 picture button is pressed first time 9 picture with CH1 to CH9 will be displayed on monitor Whenever it is pressed 9 picture displayed on monitor will be changed from CH1 CH9 to CH8 CH16 on and on The 9 picture mode for monitoring can be selected by pressing this button repeatedly D 16 8 10 picture Display If 16 picture button is pressed first time
22. can use LEFT or RIGHT button for horizontal movement UP or DOWN button for vertical movement ENTER button for selection You can define the area of the image where you don t want to detect motion Selected blocks in 14x10 blocks will be blinking To remove previously defined image block for motion detection press ENTER button again at that block After defining motion zone press ESC button to return upper Menu Motion detection zone is the area which edge of the motion blocks is not flickering The example of motion area SEED gt TRIGGER OUT DISABLE 1 to 4 It is supported to output alarm output relay output when motion is detected In case that relay output isn t requested it can be set DISABLE When motion is detected in some of video channels relay output 1 to 4 can be selected to support relay output Trigger output for motion detection in 2 can be designated as trigger output 1 Trigger output for motion detection in CH10 can be designated as trigger output 3 5 BUZZER ALERT DISABLE ENABLE If motion be detected in motion area beep sound from buzzer by BUZZER ALERT with ENABLE would be occurred during two seconds 7 WEEKLY SCHEDULE 6 WEEKLY SCHEDULE WEEK START DURATION SUN 00 00 00 00 00 00 00 00 TUE 00 00 00 00 WED 00 00 00 00 THU 00 00 00 00 FRI 00 00 00 00 SAT 00 00 00 00 HOLIDAY ENTER AN EXIT setup WEEKLY SCHEDULE press ENTER when WE
23. ding at 1 alarm 1 motion 16CH multiplexing recording at other conditions Continuous Recording in Disk Overwrite Mode Simultaneously Record Playback and Network Archiving using USB Memory Drive USB 1 1 Storage Class support User friendly Graphical User Interface GUI Manual Schedule and alarm motion recording Modes Time and Event 16 Alarm input Connections 4 relay output connection 9 9 Network Function Dynamic IP DHCP Floating IP support Live or Recorded Video Access via Ethernet Remote Configuration DDNS client support Audio Recording and Playback 1ch audio support 3 Front Panel and Rear Panel Connection Remote controller X e USB Memory Drive f 7 Microphone Sensor Alarm Cameras Input Output 2 Adaptor Video Out 16CH 12V 5A for Loop Through T TUTTUTT TUTTTUTTTTTHTTTTTTHTTTTT 75 Ohm Terminator Monitor amp Spot Speaker Ethernet ll INSTALLATION Front Panel 4 1 USB port A USB port is provided to connect external USB memory drive for archiving video 2 Video Display Channel Selection buttons Channel button from CH1 to CH16 is to select video channel displayed on monitor 3 Video Display mode selection buttons There are four kinds of video display modes which consists of s
24. e 7 NTP TIME OFF ON DVR can synchronize standard time with Time Server using Network Time Protocol NOTE If DNS server is not set properly in fixed IP address this function will not be operated 8 TIME ZONE GMT 08 00 Time information can be synchronized with time server For example to synchronize time GMT 8 for Taiwan 9 DDNS STATUS Dynamic DNS status display This DDNS status is just readable It is recommended not to use this DDNS service for fixed IP or IP sharing machine NONE It indicate that DDNS is not used ERR DDNS IP update failure OK Normal operation lt How to use DDNS service gt 1 Create User ID password and domain Name in the company which support DDNS service with free of charge Ex 2 Access to your DVR using any PC installed Net Viewer 3 Input User ID password site and DDNS enable received from company which support DDNS service in DDNS setting of remote setup of Net Viewer DVR will be upgraded as soon as DDNS setting by remote setup of Net Viewer is finished 4 Check the status of 8 DDNS STATUS of NETWORK SEYUP 9 ARCHIVING ARCHIVING ARCHIVING TYPE SINGLE MOTION ARCHIVING TIME 1 to 60 SEC ARCHIVE INFO NAME TOTAL FREE ARCHIVE LOG ENTER V 40 EXIT 1 ARCHIVE TYPE SINGLE or MOTION For archiving data via USB port first set up ARCHIVING TYPE and ARCHIVING TIME which you want to have using LEFT or RIGHT Button And then insert USB
25. e SYSTEM Menu using DOWN or UP button If ADMIN LOCK is selected as YES by LEFT or RIGHT password is requested whenever entering menu If NO password isn t requested 5 TIME FORMAT 24 12 HOURS Move Highlight bar to TIME FORMAT in the SYSTEM Menu using DOWN or UP button and press the LEFT or RIGHT button to select 24 HOURS military time or 12 HOURS AM PM Whenever Time Format is changed clock information on monitor and file information in search list will be changed together 6 DATE FORMAT MM DD YY DD MM YY MM DD YY Move Highlight bar to DATE FORMAT in the SYSTEM Menu using DOWN or UP button Date format can be changed using LEFT or RIGHT button 7 DATE TIME SET Move Highlight bar to DATE TIME SET in the SYSTEM Menu using DOWN or UP button And then press ENTER to set the time NOTE 1 If you set a date and time that is older than some of your recorded images it is not easy to manage recorded files 2 Before starting your DVR DATE TIME should be setting properly SYSTEM SETUP DATE TIME SET Year is changed by DOWN or UP button 01 11 10 50 11 By LEFT or RIGHT button SYSTEM SETUP DATE TIME SET Month is changed by DOWN or UP button 2004 01 11 10 50 11 LEFT or RIGHT button SYSTEM SETUP DATE TIME SET Date is changed by DOWN or UP button 2004 01 11 10 50 11 LEFT or RIGHT button SYSTEM SETUP DATE TIME SET Time is changed by DOWN or UP button To confirm DATE TIME set
26. e other lower BNC is used to monitor SPOT monitoring which displays all of connected video channels sequentially Audio input upper RCA and Output Lower RCA Unbalanced audio signal input and output with RCA jack Connect the audio source to audio input audio output to your amplifier because the DVR does not have amplified audio output A speaker with an amplifier will be needed for audio playback The audio input can be from an amplified source or directly from a microphone 16CH Loop through outputs 16 channel composite video outputs with D SUB connectors If the connection of loop through video outputs into another video equipments is requested 16CH Loop Through outputs can be utilized for it If loop through video outputs will be connected to another video equipments 75 Ohm termination switch should be OFF Then another video equipments should be 75 ohm terminated 75 Ohm Termination Switch If you want to connect loop through video outputs into another video equipments 75 Ohm termination switch should be OFF Then another video equipments should be 75 ohm terminated If loop through video outputs are not connected to another video equipments it should be If 75 Ohm termination switch ON or OFF is changed it will cause poor video quality 6 Alarm input and relay output 16 alarm inputs and 4 relay output with NO NC To make secure connections on the Alarm Connector Strip press and
27. equential display QUAD 9CH 16CH display mode Full Picture Display mode Full picture can be selected by channel selection button from CH1 to CH16 Sequential Display mod If this button is pressed under given video display mode each video display mode is switched sequentially For example if this button is pressed in QUAD mode QUAD picture is switched sequentially from CH1 4 CH5 8 to CH13 16 QUAD Display modd If QUAD button is pressed QUAD picture will be displayed Whenever this button is pressed QUAD picture including CH1 to CH4 CH5 to CH8 CH9 to CH12 and CH13 to Ch16 will be changed in turn 9 Picture Display mod If 9 picture display button is pressed initially 9 picture with CH1 to CH9 will be displayed The coming 9 picture with CH8 to CH16 will be displayed by pressing this button one more Whenever this button is pressed 9 picture is switched in turn from to CH1 CH9 to from CH8 CH16 16 Picture Display mod B Whenever 16 picture display button is pressed picture display mode will be changed from 16 picture display to 1 7 display mode 2 8 display mode 4 FUNCTION The main picture in 1 7 2 8 display of 16 picture display mode can be changed by the combination of FUNCTION and channel selection button Main picture can be changed by channel selection button from CH1 to CH16 after pressing FUNCTION button 5 KEY LOCK In order for only authorized person to operate buttons in front panel this LO
28. ged 8 Move to 9 REV STATUS of SYSTEM SETUP The SYSTEM MENU shows UPGRADE version from 0 0 3 current to 0 0 4 new SYSTEM SETUP LANGUAGE VIDEO FORMAT PASSWORD ADMIN LOCK TIME FORMAT DATE FORMAT DATE TIME SET 05 20 2005 DEFAULT REV STATUS ENG CHN NTSC o YES 24HOURS MM DD YY 10 50 11 YES NO UPGRADE 1 1 1 gt 1 1 2 ENTER V EXIT 9 Press RIGHT 2 button of front panel in your DVR 9 REV STATUS UPGRADE will be changed into 9 REV STATUS CONFIRM SYSTEM SETUP LANGUAGE VIDEO FORMAT PASSWORD ADMIN LOCK TIME FORMAT DATE FORMAT DATE TIME SET 05 20 2005 GMT HOUR SET REV STATUS ENG CHN NTSC YES 24HOURS MM DD YY 10 50 11 09 HOUR CONFIRM 1 1 1 31 1 2 ENTER AV lt gt EXIT 10 Press ENTER button of front panel in your DVR While 9 REV STATUS WAIT is appearing S W upgrade will be executed It takes around 20 seconds After completing S W upgrade your DVR will be re booted NOTE 1 After pressing ENTER button for upgrading USB Memory Driver should not be plugged out before displaying INITIALIZING message in your DVR 2 Please remove USB Memory Drive from front panel of your DVR when INITIALIZING character is displayed on monitor SYSTEM SETUP LANGUAGE VIDEO FORMAT PASSWORD ADMIN LOCK TIME FORMAT DATE FORMAT DATE TIME SET ENG CHN NTSC YES 24HOU
29. iplexed video signals from the camera or cameras which motion is detected and display only the camera with motion during 30 seconds Recoding duration can be selected in MOTION SETUP menu To access MOTION SETUP press ENTER when MOTION SETUP in MAIN MENU using DOWN or UP button is highlighted with blue color The menu above will appear on monitor 1 SENSITIVITY 5 steps very low low normal high very high Your DVR support 5 sensitivity levels It can be selected using LEFT or RIGHT button 2 FRAME RATE Your DVR support 60 30 15 10 5 1 0 5 IPS for NTSC 50 25 16 10 5 1 0 5 IPS for PAL It can be selected using LEFT or RIGHT button 3 DURATION It define recording duration after motion is detected This DVR support 10 sec 30sec 1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 minutes It can be selected using LEFT or RIGHT button 4 CAM NUM CH1 CH16 AREA SETTING DISABLE ALL SETUP Motion Enable Disable Motion zone can be selected separately for each of sixteen cameras using LEFT or RIGHT button DISABLE means that function of motion detection isn t utilized ALL means that entire image area is selected for motion detection SETUP can be selected in order to select given image area which want to monitor motion detection Total motion area consists of 14x10 blocks To select arbitrary motion zone select SETUP using LEFT or RIGHT button And then press ENTER button to designate motion areas in 14x10 blocks You
30. m For the installation of NetViewer program in PC Setup exe in NetViewer S W CD can be executed To playback archived image file in USB memory driver First connect USB memory drive to PC then execute Netviewer program NOTE For more detail information about NetViewer program confer the user s manual of NetViewer program lt The procedure of archived file playback using NetViewer program gt A Install NetViewer program as executing Setup exe in NetViewer S W CD After finishing installation next icon will be appeared in PC B Double click the icon to execute NetViewer Program Main Window of NetViewer program will be appeared Confer next page figure C Connect USB Memory drive to USB port of PC D Search archived files using searching icon of NetViewer program E Playback the archived file as double clicking the file NOTE USB Memory driver usually will be recognized as removable disk in most of PC Confer example of recognizing USB Memory drive in PC a Is 5 30 lt NetViewer Program gt NOTE On the viewer program buttons Viewer GUI 1 Search Button S This Search Button can be used to find archived image in USB Memory drive After searching the image files double click the file And then it will be playbacked 2 Slide bar In order to move much faster the archived image where you want to see just drag this slice bar forward or backward 3 Move
31. memory drive in USB port of DVR front panel Press ARCHIVE button in playback or live mode SINGLE in ARCHIVE TYPE means that field by field image can be captured in USB memory drive MOTION means that it can be captured during the time duration when you set in ARCHIVE TIME Note Archiving operation through USB Memory Drive can be executed only in live mode or playback mode 2 ARCHIVE TIME 1 to 60 seconds and 30 minutes ARCHIVE TIME is time duration which you want to archive in MOTION 3 ARCHIVE INFO First connect USB memory drive in USB port of DVR front panel And then enter menu mode You can see the information of USB Memory Drive inserted in DVR like USB memory drive manufacturer total memory size available memory size 4 ARCHIVE LOG NONE or ENTER All of log information including DVR power OFF recording time event time and so on can be backup through USB Memory drive After backup log file you can see backup log information using WORD PAD of PC For ARCHIVE LOG first select ENTER using LEFT or RIGHT Button And the press ENTER button NOTE Don t keep to connect USB Memory drive in USB port of DVR after finishing DVR power up And don t plug out USB Memory drive when it is working Please plug out USB memory drive after Archive LED turn off When playback pictures is archived archived speed is followed by playback speed 5 The archived image playback To play archived image it needs NetViewer progra
32. nnel s which motion is are detected or external alarm is are triggered will be POP UP in monitor during maximum 30 seconds In case that motion detection or alarm event is occurred more than two channels POP UP picture will be appeared in monitor turn by turn during 3 seconds for each channels Total period of POP UP display is 30 seconds 8 POSITION According to monitor even same Video signal can be displayed on different position of monitor by the deflection characteristic of it In this case vertical and horizontal display position can be adjusted by VERTICAL and HORIZONTAL of POSITION VERTICAL 52 HORIZONTAL 205 DEFAULT NO 4 RECORDING SETUP 3 RECORDING SETUP QUALITY HIGH FRAME RATE 60 IPS NUDO OFF STOP KEY DISABLE CAMERA NUM CH01 16 RECORD ENABLE ENTER A V EXIT access RECORDING SETUP press ENTER when RECORDING SETUP in MENU using DOWN or UP is highlighted with blue color The menu above will appear on monitor 1 QUALITY LOW STANDARD STANDARD PLUS HIGH Your DVR support four recording quality from low to high It can be selected using LEFT or RIGHT button 2 FRAME RATE 60 30 15 10 5 1 0 5 IPS NTSC Your DVR support several frame rates from 0 5 to 60 Image per seconds for NTSC from 0 5 to 50 IPS for PAL It can be selected using LEFT or RIGHT button NOTE when your DVR is in recording mode some of parameters related to RECORDING can
33. nner and alcohol for cleaning They may deform the product Do not touch the exposed terminal For the power off of system normally turn off the power of the program and then power off the peripherals Do not power it off with the power button on the front panel of body Be careful to prevent a conductive object from falling into a hole that was punched for ventilation Do not dissemble and remodel the product Do not place a heavy thing on the body Do not give a shock during the movement of equipment If you use the product in the state of smoke or smell emitted it may cause fire or an electric shock For this case immediately block the power switch and contact the company or the place where you purchased the product to consult it with a special technician This user s manual is subject to change without any notice by function upgrade and SO On Table of Contents I Introduction 1 Package Contents 2 Features 3 Front Panel and Rear Panel Connection Installation 1 Front Panel 2 Rear Panel 3 Menu Tree Main MENU Programming Overview Main Menu SYSTEM SETUP DISPLAY SETUP RECORDING SETUP ALARM SETUP MOTION SETUP WEEKLY SETUP NETWORK SETUP ARCHIVING 10 HDD INFORMATION 11 SEARCH LIST 12 DISPLAY Mode 13 RECORDING Mode 14 PLAYBACK Mode IV Software Upgrade Procedure APPENDIX 1 Specification 2 Pin Description of connectors
34. observe 1 Precautions for installation Install the product on a flat floor not closed and retain the distance of more than 15 cm from the rear panel to the wall Install the product on a well ventilated place Keep it away from strong magnetism or electromagnetic wave Installing it near radio equipment such as TV and radio may cause a fault Do not install it on a place that is exposed directly to the sun or contains lots of heat such as near a heating apparatus Do not install it on a cold place Place the equipment or tools in the site remote from a busy road so that people are not hurt Do not install it on a place where there is severe vibration much humidity or soot Should use the product in the rated voltage The equipment is used as both 110V and 220V but it is set to 220V for delivery It is possible to adjust it with the changeover switch on the rear panel Connect it to the outlet with the ground terminal Discard the vinyl bag well It is dangerous to put it on the head 2 Precautions for use For the repair contact the company or the place where you purchased the product Read the user manual before using the product Do not open the cover at your discretion because there are parts sensitive to the environment within the equipment Arrange the power cord safely and do not touch it with wet hands Do not use a loose outlet or a damaged power cable Do not use benzene thi
35. ollowing or Similar statement placed in a prominent location in the text of the manual Note This equipment has been tested and found to comply with the limits for a CLASS a digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment Generates uses and can radiate radio frequency energy and if not in stalled and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of the this equipment in a residential area is likely to cause harmful interference in which cause the user will be required to correct the interference at his own expense Before Starting Your DVR Operation This document is a basic manual for the DVR users This manual describes the appearance and name of products how to configure the system program and how to use the system Before using DVR a user should read the contents of user manual and then deal with the product considering the precautions defined in the manual To open the system case and touch the inner parts for corrective maintenance a user should contact the place where he she purchased the products to get the help from expert In addition if there is any question for use or any damage on the product please contact call the place where he she purchased the products Precautions for safety User should
36. ranty Guide The quality of this product is guaranteed by strict quality control process and tests If the Product is damaged despite following the instructions provided in the manual this Warranty will be in effect provided the product is damaged within 1 year of purchase Warranty Guide Check the Product Warranty Sheet to make sure it is still in effect Check the problem again and contact your dealer you purchased from About product repair exchange or refund we follow the compensation regulation for customer s loss announced by the Economic Planning Board Warranty e If the product is damaged despite following the instructions provided in the manual this warranty will be in effect provided the product is damaged within 1 year of purchase Service fee and replacement parts will be charged in below cases 1 Damaged the user s carelessness 2 Damaged due to a natural disaster 3 Damaged due to the user not following the instructions and cautions written in the user s guide 4 Damaged due to incorrect power voltage and or frequency being used 5 If the Product Warranty sheet is expired 6 Damaged due to an engineer not employed by Sole Vision modifying the system f your system is damaged after the warranty period free repair service will not be available If you wish the system to be repaired service fee and replacement parts will be charged Warranty Product Model Name Serial Number
37. t be changed 3 AUDIO ON OFF Your DVR can select whether to record audio signal with video signal together or not It can be selected using LEFT or RIGHT button 4 STOP KEY DISABLE ENABLE In case of manual recording manual recording is started and stop by the REC STOP button This STOP KEY ENABLE can protect the recording stop which is not intended NOTE While your DVR is on recording mode it doesn t support the setup related to the recording including recording quality frame rate audio ON OFF and date time setup in SYSTEM SETUP 5 CAMERA NUM 1 16 RECORD ENABLE DISABLE Recording channel from CH1 to CH16 can be selected separately The video channel which don t need to record can be set DISABLE after selecting channel in CAMERA NUM 5 ALARM SETUP 4 ALARM SETUP FRAME RATE 60 IPS DURATION 3 MIN SENSOR TYPE NONE N O N C ALARM INPUT 01 to 16 TRIGGER OUT DISABLE 1 to 4 BUZZER ALERT DISABLE AV lt gt EXIT To access ALARM SETUP press ENTER when ALARM SETUP in MAIN MENU using DOWN or UP is highlighted with blue color The menu above will appear on monitor 1 FRAME RATE 60 30 15 10 5 1 0 5 IPS NTSC Your DVR support several frame rates from 0 5 to 60 Image per seconds for NTSC from 0 5 to 50 IPS for PAL It can be selected using LEFT or RIGHT button 2 DURATION It define recording duration after motion is detected This DVR support 10 sec 30 sec 1 2
38. ting ENTER EAN te eA button should be pressed After setting DATE TIME ESC or ENTER button can be used in order to return upper Menu 8 DEFAULT Return to factory default mode 9 REVISION STATUS It shows DVR software version Whenever upgrading software upgraded version will be displayed 3 DISPLAY SETUP 2 DISPLAY SETUP ADJUST CHANNEL CHI CH2 CH16 BRIGHTNESS 1 99 CONTRAST 1 99 PTZ TYPE SEQ DWELL TIME NONE 1 60 SEC SPOT DWELL 1 60 SEC TIME DATE OSD ON OFF NUMBER OSD OFF 055 ON OFF POP UP DISPLAY ON OFF POSITION ENTER AV 4 EXIT To access DISPLAY SETUP press ENTER button after moving highlight bar to DISPLAY SETUP in MAIN MENU Above menu will appear on monitor 1 ADJUST CHANNEL CH1 CH2 CH3 CH4 The camera channel to adjust brightness contrast can be selected by ADJUST CHANNEL using LEFT or RIGHT button BRIGHTNESS 1 to 99 BRIGHTNESS can be changed using LEFT or RIGHT button NOTE Minimum value is 1 very dark maximum value is 99 very bright CONTRAST 1 to 99 CONTRAST can be changed using LEFT or RIGHT button PTZ TYPE Pan Tilt and zooming protocol selection The high end camera s with panning tilting and zooming function would be connected with some of video inputs The camera s has have its own control protocol to control panning tilting and zooming according to PTZ camera manufacturer In order to control PTZ of the
39. to beginning of archived images 4 Move single frame backward 5 Playback button 6 Stop PAUSE button 7 Move single frame forward 8 Move to end of archived images lt Example USB Memory Drive will usually be recognized as removable Disk in PC gt My Computer File Edit View Favorites Tools Help Back search Folders lt TAR ay Address 3 My Computer x Go Norton Antivirus System Tasks la View system information 12 Add or remove programs GF Change setting Eject this disk Other Places X Network Places My Documents Shared Documents G Control Panel Details Removable Disk 1 Removable Disk File System FAT Files Stored on This Computer C Shared Documents Hard Disk Drives Cae Local Disk C pe backup E Devices with Removable Storage H 31 Floppy A ge YSE600KOR1 G Other 10 HDD INFORMATION 9 HDD INFORMATION HARD DISK WDC WD1200 TOTAL 111GB FREE 111GB 2 FORMAT HDD NO OVERWRITE a joiner s Documents a Local Disk D ro backup2 H CD RW Drive F ENTER WA A EXIT 1 HARD DISK This machine automatically detects HDD display HDD information in menu like total HDD capacity and available memory space 2 FORMAT HDD This support quick HDD format function To format HDD in FORMAT HDD first select YES using LEFT or RIGHT Button and then press ENTER b
40. utton Press ENTER button again after MASTER is displayed Then quick format is implemented with CONFIRM 3 OVERWRITE Your DVR can be enable or disable HDD overwrite when HDD is full 11 Search List SEARCH LIST 10 10 The number of recorded files LISTTYPE ALL 10 15 2004 10 15 2004 10 20 10 15 2004 11 20 10 15 2004 12 20 10 15 2004 13 20 10 15 2004 13 20 10 15 2004 14 20 10 15 2004 14 20 10 15 2004 15 20 10 15 2004 16 20 10 15 2004 17 20 10 15 2004 18 20 10 15 2004 18 50 10 15 2004 19 20 10 15 2004 19 25 10 15 2004 20 20 10 15 2004 20 25 10 15 2004 21 20 10 15 2004 21 50 10 15 2004 22 00 10 15 2004 23 10 Latest recorded file ENTER AV lt gt EXIT Search list can be sorted all the recorded file as ALL TIME MANUAL ALARM MOTION SCHEDULE using DOWN or UP button for fast file searching SEARCH LIST 10 10 SEARCH LIST 1 10 15 2004 10 20 10 15 2004 11 20 10 15 2004 10 20 10 15 2004 11 20 Change the numbers by highlighting them and using the DOWN or UP button to increase or decrease the number for year month date after moving from ALL to 2004 10 using LEFT or RIGHT Button SEARCH LIST 10 10 mE AE ee To select recorded file for playback 10 10 15 2004 22 00 10 15 2004 23 10 DOWN or UP button is used after pressing ENTER button Playback will be started by pressing SEARCH LIST 10 10 PLAY button gt button LIST TYPE ALL 10 15 2004 1 10 15 2004 10 20 10 15 2004 11 20 NO
Download Pdf Manuals
Related Search