Blizzard Lighting, LLC www.blizzardlighting.com Waukesha, WI USA
Contents
1. wi ICE LIGHTING Blizzard Lighting LLC www blizzardlighting com Waukesha WI USA Copyright c 2014 TABLE OF CONTENTS The Puck CSI Xtreme LED PAR Can 1 1 Getting Started 3 What s In The Box 3 Getting It Out Of The Box 3 Powering Up 3 Getting A Hold Of Us 3 Safety Instructions Don t Stick Your Hand In The Toaster 4 2 Meet The Puck CSI Xtreme LED PAR Can 5 Features 5 DMX Quick Reference 5 The Puck CSI Xtreme Pin up Picture 6 3 Setup 7 Fuse Replacement 7 Connecting A Bunch Of Puck CSI Xtreme LED PAR Cans 7 Data DMX Cables 7 Cable Connectors 8 3 Pin 5 Pin Huh 8 Take It To The Next Level Setting up DMX Control 8 Fixture Linking Master Slave Mode 9 Mounting Rigging 9 Using this fixture with the wiCICLE Wireless DMX System 10 4 Operating Adjustments 12 The Control Panel 12 Control Panel Menu Structure 13 DMX Mode 14 Set the DMX Starting Address 14 Set the DMX Channel Mode 14 Master Slave Mode 14 Sound Active Pixel Group Auto Fade Mode 14 Individual Pixel Group Intensity 15 Troubleshooting 15 5 Appendix 16 Keeping The Puck CSI Xtreme As Good As New 16 Returns Gasp 16 Shipping Issues 16 Tech Specs 17 Page 2 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC 1 GETTING STARTED What s In The Box e 1 x Puck CSI Xtreme UV LED PAR Fixture e 1x IEC Power Cord e This Lovely User Manual Getting It Out Of The Box Congratulations aspirin2. 2014 Blizzard Lighting LLC Figure 1 The Puck CSI Pin Up Picture Dual Mounting Yokes 36x 3 watt UV LEDs Ridiculously Thin Figure 2 The Rear Connections DMX In DMX Out LED Control Panel Microphone AC Power In Out Page 6 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC 3 SETUP Before replacing a fuse disconnect power cord ALWAYS replace with the same type and rating of fuse Fuse Replacement With a flat head screwdriver wedge the fuse holder out of its housing Remove the damaged fuse from its holder and replace with exact same type fuse Insert the fuse holder back in its place and reconnect power Connecting A Bunch of Puck CSI Xtreme Flat LED PAR Cans You will need a serial data link to run light shows using a DMX 512 controller or to run shows on two or more fixtures set to sync in mas ter slave operating mode The combined number of channels required by all the fixtures on a serial data link determines the number of fix tures the data link can support Fixtures on a serial data link must be daisy chained in one single line Also connecting more than 32 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal The maximum recommended cable run distance is 500 meters 1640 ft The maximum recommended number of fixtures on a serial data link is 32 fixtures Data DMX Cabl
3. El 0 ohm 1 4 watt resistor CAUTION Do not allow contact between the common and the fix ture s chassis ground Grounding the common can cause a ground loop and your fixture may perform erratically Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other 3 Pin 5 Pin Huh If you use a controller with a 5 pin DMX output connector you will need to use a 5 pin to 3 pin adapter They are widely available over the internet and from specialty retailers If you d like to build your own the chart below details a proper cable conversion O A e Output Input Take It To The Next Level Setting Up DMX Control Step 1 Connect the male connector of the DMX cable to the female connector output eccceess e CA mn pme eee on the controller ZA AAA AAA TA 0 Step 2 Connect the female connector of the DMX cable to the first fixture s male connec tor input Note It doesn t matter which fixture address is the first one connected We recommend connecting the fixtures in terms of their proximity to the controller rather than connecting the lowest fixture DMX IN number first and so on il I giidi iil Next Fixture in Chain Step 3 Connect other fixtures in the chain from output to input as above Place a DMX terminator on the output of the final fixture to ensure best communication DMX IN DMX OUT To
4. and ensure properly rated rigging is used when mounting fixutres overhead Adjust the angle of the fixture by loosening both knobs and tilting the fixture After finding the desired position retighten both knobs e When selecting installation location take into consideration lamp replacement access if applicable and routine maintenance e Safety cables MUST ALWAYS be used e Never mount in places where the fixture will be exposed to rain high humidity extreme temperature changes or restricted ventilation Page 9 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC USING THIS FIXTURE WITH THE wiCICLE WIRELESS DMX SYSTEM In addition to the unbridled thrill you already re ceived the first time you plugged in your fixture LU E E you ll be delighted to know that This fixture also works seamlessly with our wiCICLE Wireless DMX system without additional power e ONLY fixtures bearing this logo are certified for use with the wiCICLE without external power e Unauthorized modification and or using the wiCICLE with unap proved fixtures may cause damage to the wiCICLE or fixture UNDER NO CIRCUMSTANCES IS BLIZZARD LIGHTING RESPONSIBLE FOR ANY DAMAGE FROM SUCH OPERATION e Fixtures bearing the above logo MUST only use cable and connectors which separate chassis case ground from cable shielding Cabling with the shield con nected to the connector s case chassis may cause malfunc
5. page intentionally left blank Page 19 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC Enjoy your product Our sincerest thanks for your purchase The team O Blizzard Lighting
6. the desired menu function Use the lt UP gt and lt DOWN gt buttons to navigate the menu options Press the lt ENTER gt button to select the menu function currently displayed or to enable a menu option To return to the previ ous option or menu without changing the value press the lt MENU gt button Page 12 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC ic To set DMX address 1 512 as mo os gt gt I a l A Ma y i ne il To choose 7 channel DMX mode i pre P a To choose 4 channel DMX mode Set as master fixture Lim ro e Set as slave fixture Sound Active Mode lt ENTER gt gt Pixel Group 1 _ gt Pixel Group 2 Pixel Group 3 5 IQ IS asi a o Lin J pu mo Le T a Oo gt Pixel Group 4 DI 5 gt Pixel Group 5 ob gt Pixel Group 6 Vr T ss a gt Pixel Group 7 oo oS Pixel Group 8 gt gt Pixel Group 9 o il gt Pixel Group 10 paee T n gt gt Pixel Group 11 Pixel Group 12 o Io pre T Le E Pixel Group 13 o O a a L Pixel Group 14 ja ja ja ja ja ja ja ja ja us ua ua P EQ EES ES ES ES ES ES ES ES ES ES ES by pe Io Pixel Group 15
7. A Don t worry this is easy Just send an email to support blizzardlighting com and we ll is sue you an RA Then you ll need to send the unit to us using a trackable pre paid freight method We suggest using USPS Priority or UPS Make sure you carefully pack the fixture for transit and whenever possible use the original box amp packing for shipping When returning your fixture for service be sure to include the following 1 Your contact information Name Address Phone Number Email address 2 The RA issued to you 3 A brief description of the problem symptoms We will at our discretion repair or replace the fixture Please remember that any shipping damage which occurs in transit to us is the customer s responsibility so pack it well Shipping Issues Damage incurred in shipping is the responsibility of the shipper and must be re ported to the carrier immediately upon receipt of the items Claims must be made within seven 7 days of receipt Page 16 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC Tech Specs Width T Power SSS oma OOOO U OSO comro SSCS 2 year limited warranty does not cover malfunction Warranty caused by damage to LED s Page 17 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC This page intentionally left blank Page 18 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC This
8. Next Fixture Page 8 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC Fixture Linking Master Slave Mode 1 Connect the male 3 pin connector side of the DMX cable to the output female 3 pin connector of the first fixture 2 Connect the end of the cable coming from the first fixture which will have a female 3 pin connec tor to the input connector of the next fixture con sisting of a male 3 pin connector Then proceed to connect from the output as stated above to the input of the following fixture and so on A quick note Often the setup for Master Slave and Standalone operation requires that the first fixture in the chain be initialized for this purpose via either settings in the control panel or DIP switches Secondarily the fixtures that follow may also re quire a slave setting First Fixture in Chain Next Fixture in Chain To Next Fixture Check the Operating Adjustments section in this manual for com plete instructions for this type of setup and configuration Mounting Rigging This fixture may be mounted in any SAFE position provided there is enough room for ventilation It is important never to obstruct the fan or vents pathway Mount the fixture using a suitable C or O type clamp The clamp should be rated to hold at least 10x the fixture s weight to ensure structural sta bility Do not mount to surfaces with unknown strength
9. Speed Too Check to ensure proper setup of speed adjustment Fast Slow Check fuse AC cord and circuit for malfunction Blown Fuse Check AC cord and circuit for damage verify that moving parts are not restricted and that unit s ventilation is not obstructed Slow Movement Verify that 220V 110V switch is in the correct position if applicable Also check that speed channels are set appropriately No Response to Verify that the fixture is in Sound Active mode Audio Adjust Audio Sensitivity If Applicable Fixture Not Make sure all connectors are seated properly and securely Responding Use Only DMX Cables and or check cables for defects Responding Er Install a Terminator raticly Reset fixture s Intermittent Check lamp for properly installation Lamp Relamp lamp may have reached end of life Remote Doesn t Verify remote control cable is installed properly and securely Work Verify remote is correct type CA 9 or other as applicable Fixture Moving Verify proper mode of operation Is the fixture in Auto mode On Its Own If your problem persists or isn t listed contact support blizzardlighting com Page 15 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC 5 APPENDIX Keeping Your Puck CSI Xtreme As Good As New The fixture you ve received is a rugged tough piece of pro lighting equipment and as long as you take care of it it will take care of you That said like a
10. d for indoor use only e To prevent risk of fire or shock do not expose fixture to rain or moisture e Make sure there are no flammable materials close to the unit while operating e The unit must be installed in a location with adequate ventilation at least 20in 50cm from adjacent surfaces Be sure that no ventilation slots are blocked e ALWAYS disconnect from the power source before servicing or replacing fuse and be sure to replace with same fuse size and type e ALWAYS secure fixture using a safety chain NEVER carry the fixture by its cord Use its carrying handles e DO NOT operate at ambient temperatures higher than 104 F 40 C e In the event of a serious operating problem stop using the unit immediately NEVER try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized tech nical assistance center Always use the same type spare parts e NEVER connect the device to a dimmer pack e Make sure the power cord is never crimped or damaged e Never disconnect the power cord by pulling or tugging on the cord e Avoid direct eye exposure to the light source while it is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact Blizzard Lighting at sup port blizzardlighting com Page 4 The Puck CSI Xtre
11. eme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC Fade Mode 1 Use the lt MENU gt button to navigate to ShNd then press lt ENTER gt 2 Then use the lt UP DOWN gt buttons to display FAde then press lt ENTER gt 3 Press the lt UP DOWN gt buttons to navigate the speed setting from SP1 slow to SP8 fast 4 Press lt ENTER gt The selected fade will start in 15 seconds Individual Pixel Group Intensity Allows the user to adjust the intensity level of each grouping of LEDs These settings are global they will effect all modes 1 Use the lt MENU gt button to navigate to NAnu then press lt ENTER gt 2 Then use the lt UP DOWN gt buttons to choose either red Gree bLue or Uhlt 3 Press the lt ENTER gt button 4 Use the lt UP DOWN gt buttons to select from O off to 255 100 5 Press the lt ENTER gt button to confirm Troubleshooting Symptom Solution SSCS Fixture Auto Shut Check the fan in the fixture If it is stopped or moving slower than Off normal the unit may have shut itself off due to high heat This is to protect the fixture from overheating Clear the fan of obstructions or return the unit for service Beam is Dim Check optical system and clean excess dust grime Also ensure that the 220V 110V switch is in the correct position if applicable No Light Output Check to ensure fixture is operating under correct mode IE sound active auto DMX Etc if applicable Chase
12. g crime fighter and or psychedelic music aficionado Now that you ve got The Puck CSI Xtreme or hopefully Xtreme s you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition If anything looks as if it has been damaged in transit notify the shipper immediately and keep the packing material for inspection Again please save the carton and all packing materials If a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing Powering Up All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel is used solely for a 0 to 100 switch AC Voltage Switch Not all fixtures have a voltage select switch so please verify that the fixture you receive is suitable for your local power supply See the label on the fixture or refer to the fixture s specifications chart for more information A fixture s listed current rating is its average current draw under normal conditions Check the fixture or device carefully to make sure that if a voltage selection switch exists that it is set to the correct line voltage you will use Warning Verify that the voltage select switch on your unit matches the line voltage applied Damage to your fixture may result if the line voltage applied does not match the voltage indica
13. h to DMX mode upon receiving DMX signal our Pucks do that If you plug a wiCICLE receiver into an autosensing fixture set as a mas ter chances are good that the wiCICLE receiver will begin transmitting the master program Most times this is undesirable and taking the two seconds to switch these programs off will solve a lot of ails Got that done Good Then let s proceed 1 Plug the wiCICLE Receiver into the DMX IN connector of the fixture and verify it is receiving power the STATUS LED should illuminate 2 Connect the AC DC adaptor to the wiCICLE Transmitter and verify it is re ceiving power the STATUS LED should illuminate 3 Press the RECESSED SELECTOR BUTTON on the Transmitter to select the operating channel group The system will store this setting for future use The 7 Color Status LED will change color to indicate the current channel group GROUP 1 RED GROUP 2 GREEN GROUP 3 YELLOW NOTE GROUP number also corresponds to the ao E a GROUP setting on our LightCaster wireless DMX GROUP 6 CYAN Transceiver GROUP 7 WHITE 4 Follow the same procedure on the Receiver to select the channel group 5 Once both the transmitter and receiver s are both set to the same chan nel group connect the transmitter to the DMX controller or the DMX out of a fixture on your DMX chain 6 Once a DMX signal is provided to the transmitter the status LED will blin
14. ing To link fixtures together you ll need data cables You should use data grade cables that can carry a high quality signal and are less prone to electromagnetic interference For instance Belden 9841 meets the specifications for EIA RS 485 applications Standard microphone cables will probably be OK but note that they cannot transmit DMX data as reliably over long distanc es In any event the cable should have the following characteristics 2 conductor twisted pair plus a shield Maximum capacitance between conductors 30 pF ft Maximum capacitance between conductor amp shield 55 pF ft Maximum resistance of 20 ohms 1000 ft Nominal impedance 100 140 ohms Page The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC Cable Connectors Cables must have a male XLR connector on one end and a female XLR connector on the other end Duh A Word on Termination DMX is a resilient communication protocol however errors still occasionally occur Termination reduces signal errors and therefore best practices include use of a terminator in all circumstances If you are experiencing problems with erratic fixture behavior especially over long signal cable runs a terminator may help improve performance To bulld your own OMX Terminator Obtain a 120 ohm 1 4 watt resistor and wire it between pins 2 amp 3 of the last fixture They are also readily available from specialty retailers
15. jo a ae Y o pe pre a Auto Mode Speed SP1 SP8 T j J i tu ry Fade Mode Speed SP1 SP8 Pixel Group 1 Intensity 0 255 gt ro pesca a fo w Ly a H Pixel Group 2 Intensity 0 255 7 mo rc Pixel Group 3 Intensity 0 255 jr sto T m Control Panel Menu Structure Pixel Group 4 Intensity 0 255 gt Test Mode Auto Check Fri gt Displays Total Running Hours Page 13 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC DMX Mode Allows the unit to be controlled by any universal DMX controller Set the DMX Starting Address 1 To set the DMX address of the fixture use the lt MENU gt button to navigate to Addr then press lt ENTER gt 2 Then use the lt UP DOWN gt buttons to choose the starting DMX address within the range of 000 512 3 Press the lt ENTER gt button to confirm Set the DMX Channel Mode 1 To set the DMX channel mode of the fixture use the lt MENU gt button to navigate to ChNd then press lt ENTER gt 2 Then use the lt UP DOWN gt buttons to highlight 7CH or 4CH 3 Press the lt ENTER gt button to confirm Master Slave Modes Allows you to link up to 32 units together without a controller 1 To set the unit to act as either a master or slave use the lt MENU gt button to navigate to SLNd then press lt ENTER gt 2 Use the lt UP DOWN gt button
16. k RED slowly until communication is established with the receiver The status LED onthe receiver s will flash GREEN slowly until communication is estab lished 7 Once the clearest channel is auto selected the status LEDs will blink quickly on both the transmitter and receiver NOTE The color of the LED DURING operation does not indicate channel group instead it indicates whether the unit is transmitting or receiving That s It Page 11 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC 4 OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with the Puck CSI Xtreme are accessed by using the control panel on the rear of the fixture There are 4 control buttons below the LED display which allow you to navigate through the various control panel menus lt MENU gt Is used to navigate to the previous higher level menu item lt UP gt Scrolls through menu items and numbers in ascending order lt DOWN gt Scrolls through menu items and numbers in descending order lt ENTER gt Is used to select and confirm store the current selection The Control Panel LED Display shows the menu items you select from the menu map on page 13 When a menu function is selected the display will show immediately the first available option for the selected menu function To select a menu item press lt ENTER gt Press the lt MENU gt button repeatedly until you reach
17. me User Manual Rev B Copyright c 2014 Blizzard Lighting LLC 2 MEET THE PUCK CSI XTREME CONTROL FEATURES e High output UV via 36x 3w 390 410nm UV LEDs e Full on UV LED intensity 4 separate LED pixel patterns e Variable electronic strobe e Variable electronic dimmer e Built in automated programs via DMX and master slave e Built in sound active programs ADDITIONAL FEATURES e Lightweight and compact It kept its New Years resolution e 4 Button LED control panel for easy programming e Dual bracket for flexibility in mounting e Power outlet for fixture linking DMX Quick Reference 7 Channel Mode Channel Channel Value What It Does 1 000 lt gt 255 Master Dimmer 0 lt gt 100 12 000 lt gt 255 Pattern 1 Intensity 0 lt gt 100 3 000 lt gt 255 Pattern 2 Intensity 0 lt gt 100 4 000 lt gt 255 Pattern 3 Intensity 0 lt gt 100 5 000 lt gt 255 Pattern 4 Intensity 0 lt gt 100 6 000 lt gt 255 Strobe slow lt gt fast Auto Mode slow lt gt fast DMX Quick Reference 4 Channel Mode Channel Channel Value What It Does 1 000 lt gt 255 Pattern 1 Intensity 0 lt gt 100 2 000 lt gt 255 Pattern 2 Intensity 0 lt gt 100 3 000 lt gt 255 Pattern 3 Intensity 0 lt gt 100 4 000 lt gt 255 Pattern 4 Intensity 0 lt gt 100 Page 5 The Puck CSI Xtreme User Manual Rev B Copyright c
18. nything you ll need to take care of it if you want it to operate as designed You should absolutely keep the fixture clean especially if you are using it in an environment with a lot of dust fog haze wild animals wild teenagers or spilled drinks Cleaning the optics routinely with a suitable glass cleaner will greatly improve the quality of light output Keeping the fans free of dust and debris will keep the fixture running cool and prevent damage from overheating In transit keep the fixtures in cases You wouldn t throw a prized guitar drumset or other piece of expensive gear into a gear trailer without a case and similarly you shouldn t even think about doing it with your shiny new light fixtures Common sense and taking care of your fixtures will be the single biggest thing you can do to keep them running at peak performance and let you worry about designing a great light show putting on a great concert or maximizing your client s satisfaction and wow factor That s what it s all about after all Returns Gasp We ve taken a lot of precautions to make sure you never even have to worry about sending a defective unit back or sending a unit in for service But like any complex piece of equip ment designed and built by humans once in a while something doesn t go as planned If you find yourself with a fixture that isn t behaving like a good little fixture should you ll need to obtain a Return Authorization R
19. s to highlight NASt master or SLAu slave 3 Press the lt ENTER gt button to confirm There can be only one master fixture in the DMX chain The first fixture should be set as the master while the others set as slave units It may be necessary to use a terminator at the last fixture Sound Active Pixel Groups Auto 8 Fade Mode Display static pixel groups individually or combined in sound active auto or fade modes Sound Active Mode 1 Use the lt MENU gt button to navigate to ShNd then press lt ENTER gt 2 Then use the lt UP DOWN gt buttons to display SoUn the display will flash 3 Do not press any buttons You will enter sound active mode in 15 seconds Static Pixel Groups 1 Use the lt MENU gt button to navigate to ShNd then press lt ENTER gt 2 Then use the lt UP DOWN gt buttons to display CoLo then press lt ENTER gt 3 Press the lt UP DOWN gt buttons to display Co 1 Co15 4 Press the lt ENTER gt button then lt ENTER gt again to save Auto Mode 1 Use the lt MENU gt button to navigate to ShNd then press lt ENTER gt 2 Then use the lt UP DOWN gt buttons to display CoLo then press lt ENTER gt 3 Press the lt UP DOWN gt buttons to display Auto 4 Press the lt ENTER gt button then from here use the lt UP DOWN gt buttons to navigate the speed setting from SP1 slow to SP8 fast 5 Press the lt ENTER gt button then lt ENTER gt again to save Page 14 The Puck CSI Xtr
20. ted on the voltage selector switch All fixtures must be connected to circuits with a suitable Ground Earthing Getting A Hold Of Us If something is wrong just give us a call or send an email We ll be happy to help honest Blizzard Lighting N16 W23390 Stoneridge Dr Suite E Waukesha WI 53188 USA www blizzardlighting com 414 395 8365 Email support blizzardlighting com Disclaimer The information and specifications contained in this document are subject to change without notice Blizzard Lighting assumes no responsibility or liability for any errors or omissions that may appear in this user manual Blizzard Lighting reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time You can download the latest version of this document from www blizzardlighting com Page 3 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC SAFETY INSTRUCTIONS Please read these instructions carefully They include important information about the installation usage and maintenance of this product e Please keep this User Guide for future use If you sell the unit to someone else be sure that they also receive this User Guide e ALWAYS make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the de cal or rear panel of the fixture e This product is intende
21. tion and damage to the wiCICLE or fixture e wiCICLE transmitters have additional power requirements and there fore cannot be powered directly from the fixture You will need to utilize the supplied AC DC adaptor to drive wiCICLE transmitters in your system WE HAD THIS SPACE SO WE FIGURED WE D DRAW YOU A PICTURE Antenna Housing amp 1 2 wave Antenna Antenna ferrule amp articulation joint Stainless Steel Housing Recessed Selector Button Status LED 3 Pin XLR Connector Male on transmitter Female on receiver model Page 10 The Puck CSI Xtreme User Manual Rev B Copyright c 2014 Blizzard Lighting LLC Each wiCICLE acts as both a transmitter and a receiver depending on whether a DMX source is applied to the integral XLR connector This is an extremely powerful feature of the system however it also requires 1 piece of due dili gence and that is the removal of extraneous DMX signals from your lighting rig BEFORE proceeding SO BEFORE DOING ANYTHING ELSE YOU SHOULD DISABLE ANY BUILT IN PROGRAMS IN THE FIXTURES YOU WISH TO CONNECT AND OR SET THEM AS SLAVES PRIOR TO RETURNING THEM TO DMX MODE IF APPLICABLE Most fixtures contain a built in automatic sound active or custom program which is designed to operate with the fixture NOT connected to a DMX chain Some of these programs will automatically run unless the fixture is set to slave mode These fixtures typically sense DMX automatically and switc
Download Pdf Manuals
Related Search