Invacare Softform Premier Active
Contents
1. Yes you can Softform Premier Active Cushion User Manual lt Yes you can Alarm Mode In the event of pressure loss an audible intermittent beep shall sound and the red low pressure led will flash The audio alarm can be muted by pressing the ALARM MUTE button If at any time there is a power failure a constant audible beep shall sound Please note that pressing the ALARM MUTE will not function in this case Power needs to be re established for Pump to function correctly If power cannot be re established the alarm may be muted by pressing the power switch to the off position Refer to Troubleshooting section Transport Mode If it is necessary to move the cushion or bedside chair simply disconnect the pump power lead and if necessary the air supply hose When the system is ready to reactivate follow the Installing the System instructions from stage 2 Troubleshooting 1 If the system appears to be non functioning and the System in Cycle light is out the mains power is lost e Check that the unit is plugged in at both ends and switched on e Check replace fuses in power plug and pump main inlet This must be undertaken by a suitably qualified and competent electrician 2 System will not pressurise or pressure is lost e Check air hose set is correctly fitted to pump and cushion e Check that the air hose is not kinked or crushed in the mattress or by the2. A 5 metre power lead Instructions for Use e Read the instructions carefully before use e Remove all packaging before use e Place the Softform Premier Active Cushion directly onto a bedside chair Technical S ecification Pump Unit Main Supply Rated Input Current Supply Fuse Noise Level Classification Cycle Time Size Weight Air Flow Operating Pressure Tested to 220 240 AC 50Hz 1A 2 XP LA lt 32 Db Class 1 Type B 10 min 237mm x 177mm x 655mm 2 Kg 4 Ltr per min 60mm Hg EC Directive 89 336 EEC BS EN 55022 1998 EN 61001 1 2 1993 Manufactured to Comply to EN 60601 1 Cushion Cover Two way stretch vapour permeable water resistant Composite Blue Gr RX 39 200 Pink Gr RX 39 120 Air Insert Polyurethane Air Insert Size 46cm x 51cm x 15 2cm Standard Size Weight 1 5kgs Fire Retardency BS 5852 1982 ignition sources 0 1 and crib 5 Cover tested to BS7175 1989 Service amp Maintenance The Softform Premier Active system is designed to be maintenance free however the system should be checked periodically for damage or excessive wear The mains lead and hose connections should be carefully checked for damage including kinks If any problems occur that cannot be simply rectified please contact Customer Services on 44 0 1656 647327 Cleaning amp Infection Control rocedures decontamination Always use universal precautions especially where the product is kno
3. bed frame e Check for leaks in the cell system Warning Do not attempt to dismantle pump Failure to comply with this will invalidate the warranty and may result in electrocution or fatal injury Warranty The Softform Premier Active System is manufactured from high quality materials and is designed to operate highly effectively and efficiently The Active System component parts are covered by the following warranty periods e Cover Warranty 12 months e Foam Warranty 12 months e Pump Warranty 24 months e Air Insert Warranty 12 months In the event of the need to return the product under warranty please contact Customer Services on 44 0 1656 647327 who will arrange collection and upon inspection resolve the enquiry appropriately Decontamination procedures must be adhered to prior to returning any product General Description The Softform Premier Active cushion system is a pressure relieving static cushion that contains an alternating air cell insert The Softform Premier Active cushion system acts as a static pressure reducing support cushion for patients at High Risk that can by facilitating the air pump introduce effective alternating pressure if the patients condition requires alternating pressure therapy The complete system comprises of 1 A cushion insert comprised of alternate inflatable air cells that connect to a twin air connector hose 2 A micro processor controlled air pump unit 3
4. ctive twin hose line to the Pump Connect the mains power lead to the pump and a suitable power supply Switch on the mains power and the pump switch The system will start to pressurise indicated by a flashing green LED System in cycle and three audible beeps Once operating pressure is reached the green light will be Insert the power permanently illuminated and the pump will emit three short connector and audible beeps switch power on Invacare Ltd South Road Bridgend Industrial Estate Bridgend CF31 3PY UK Tel 0 1656 647327 Fax 0 1656 649016 Email uk invacare co uk Orders ordersuk invacare com Web www invacare com Invacare Ireland Ltd Unit 5 Seatown Business Campus Seatown Road SWORDS County Dublin Ireland Tel 353 1 810 7084 Fax 353 1 810 7084 Email Ireland invacare com Web www invacare ie Ce
5. wn or suspected to be contaminated Always refer to your Infection Control Manual for advice The cushion cover may be wiped clean using a solution of neutral detergent and hot water applied with a single use wipe Alternatively covers can be decontaminated using a freshly prepared solution containing 1 000 ppm 0 1 available chlorine at room temperature When covers are immersed in solutions of hypochloride contact should be maintained for at least 30 minutes DO NOT USE ALCOHOLS OR PHENOLS For heavy soiling the removable cover may be laundered at 80 C with a dilute detergent solution Following application the cover should be rinsed with clean water and thoroughly dried before placing back on the product The Active insert may also be wiped down using a solution of neutral detergent and hot water applied with a single use wipe The pump unit tubing and mains lead may be wiped over With a neutral detergent ALWAYS ENSURE THE MAINS SUPPLY HAS BEEN DIS CONNECTED TRY TO AVOID WETTING THE PUMP Installing the System hung by the built in pump hooks The pump may be placed on the floor This will not affect the pump s performance but may expose it to possible damage 1 Place the pump unit next to the bedside chair preferably Position the Pump Unit next to the chair Remove the Active twin hose from the cushion and connect it to the pump An automatic click will signify a secure connection Connect the A
Download Pdf Manuals
Related Search